2015 Citroen DS3 fuel

DS3_en_Chap04_conduite_ed01-2015
There is a risk of damage to the gearbox:
- i f you press the accelerator and
brake
  pedals   at   the   same   time,
-
 
i
f   you   force   the   movement   of   the  
s

elector   from   the   P position to
another position when the battery
is
  flat.
To
  reduce   fuel   consumption   when   at
 a

  prolonged   standstill   with   the   engine
 r

unning   (traffic   jam...),   put   the   selector   in
 t

he
n  

position   and   apply   the   parking   brake.
If the selector is not in position P
,
when
 
the
 
driver's
 
door
 
is
 
opened
 
or
 
a

pproximately
 
45
 
seconds
 
after
 
the
 
i

gnition
 
is
 
switched
 
off,
 
a
 
warning
 
m

essage
 
appears
 
in
 
the
 
screen.
F

R

eturn the selector to position P ;
 
t

he
 
message
 
disappears.
When
 
driving
 
on
 
flooded
 
roads
 
or
 
when
 
c

rossing
 
a
 
ford,
 
proceed
 
at
 
walking
 
p

ace.
Operating fault
Manual operation
When the ignition is on, the lighting o
f   this   warning   lamp,   accompanied  
b

y
 
an
 
audible   signal   and   a   message   in   the  
m

ultifunction   screen,   indicates   a   gearbox   fault.
In
 
this
 
case,   the   gearbox   switches   to   back-up  
m

ode
 
and
 
is   locked   in   3rd   gear.   You   may   feel  
a

 
substantial   knock   when   changing   from   P
to R
 
and
 
from  n to R .
  This   will   not   cause   any  
d

amage
 
to
 
the   gearbox.
Do
 
not
 
exceed   60   mph   (100   km/h),   local   speed  
r

estrictions
 p
ermitting.
Contact
 
a
 
CITROËN   dealer   or   a   qualified  
w

orkshop
 
as   soon   as   possible.
F
Sel
ect position M for sequential c
hanging o
f
 
the
 
four
 
gears.
F

P

ush the selector towards the +
 
sign
 
to
 
c

hange
 
up
 
a
 
gear.
F

P

ull the selector towards the -
 
sign
 
to
 
c

hange
 
down
 
a
 
gear.
It
 
is
 
only
 
possible
 
to
 
change
 
from
 
one
 
gear
 
to
 
a

nother
 
if
 
the
 
vehicle
 
speed
 
and
 
engine
 
speed
 
p

ermit;
 
other wise,
 
the
 
gearbox
 
will
 
operate
 
t

emporarily
 
in
 
automatic
 
mode. This
 
symbol
 
is
 
displayed
 
if
 
a
 
gear
 
i

s
 
not
 
engaged
 
correctly
 
(selector
 
b

etween
 
two
 
positions).
d

 
disappears
 
and
 
the
 
gears
 
e

ngaged
 
appear
 
in
 
succession
 
in
 
the
 
in

strument
 pan

el.
Stopping the vehicle
Before switching off the engine, you can engage p osition P or
n 
to   place   the   gearbox   in   neutral.
In
  both   cases,   apply   the   parking   brake   to  
i

mmobilise   the   vehicle.
Invalid value during manual
operation
If the engine speed is too low or too high, the gear   selected   flashes   for   a   few   seconds,   then  
t

he   actual   gear   engaged   is   displayed.
It
  is   possible   to   change   from   position  d
(automatic)
  to   position   M   (manual)   at   any   time.
When
  the   vehicle   is   stationary   or   moving  
v

ery   slowly,   the   gearbox   selects   gear   M1
automatically.
The
  sport   and   snow   programmes   do   not  
o

perate   in   manual   mode.

11 5
DS3_en_Chap04_conduite_ed01-2015
Gear shift indicatorSystem which reduces fuel consumption by advising the driver to change up.
Operation
Example:
- Y ou   are   in   third   gear.
-
 
Y
ou   press   the   accelerator   pedal.
-
 
T
he   system   may   suggest   that   you   engage  
a

  higher   gear.
The
  information   appears   in   the   instrument  
p

anel   in   the   form   of   an   arrow. The
  system   adapts   its   gear   change  
r

ecommendation   according   to   the  
d

riving   conditions   (slope,   load, ...)   and  
t

he   demands   of   the   driver   (power,  
a

cceleration,   braking, ...).
The
  system   never   suggests:
-
 
e
ngaging   first   gear,
-
 enga

ging
 r
everse
 g
ear,
-
 
e
ngaging   a   lower   gear.
With
 
an
 
electronic
 
or
 
automatic
 
g

earbox,
 
the
 
system
 
is
 
only
 
active
 
in
 
m

anual
 m

ode.
On  vehicle   fitted   with   a   manual  
g

earbox,   the   arrow   may   be  
a

ccompanied   by   the   gear  
re

commended.
Depending
 
on
 
the
 
driving
 
situation
 
and
 
your
 v
ehicle's
 
equipment,
 
the
 
system
 
may
 
advise
 
y

ou
 
to
 
skip
 
one
 
(or
 
more)
 
gear(s).
 
You
 
can
 
f

ollow
 
this
 
instruction
 
without
 
engaging
 
the
 
i

ntermediate
 g

ears.
The
 
gear
 
engagement
 
recommendations
 
must
 
n

ot
 
be
 
considered
 
compulsory.
 
In
 
fact,
 
the
 
c

onfiguration
 
of
 
the
 
road,
 
the
 
amount
 
of
 
traffic
 
a

nd
 
safety
 
remain
 
determining
 
factors
 
when
 
c

hoosing
 
the
 
best
 
gear.
 
Therefore,
 
the
 
driver
 
r

emains
 
responsible
 
for
 
deciding
 
whether
 
or
 
not
 
t

o
 
follow
 
the
 
advice
 
given
 
by
 
the
 
system.
This
 
function
 
cannot
 
be
 
deactivated.
driving

DS3_en_Chap04_conduite_ed01-2015
Stop & StartThe Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine   restarts   automatically   -   START   mode   -   as   soon   as   you   want   to   move   off.   The   restart   takes   place   instantly,   quickly   and   silently.
Per fect
  for   urban   use,   the   Stop   &   Start   system   reduces   fuel   consumption   and   exhaust   emissions   as   well   as   the   noise   level   when   stationary.
Operation
going into engine STOP mode
For your comfort, during parking manoeuvres,   STOP   mode   is   not  
a

vailable for a few seconds after
coming
  out   of   reverse   gear.
STOP
  mode   does   not   affect   the  
f

unctionality of the vehicle, such as for
example,
  braking,   power   steering...
Never
  refuel   with   the   engine   in   STOP  
m

ode;   you   must   switch   off   the   ignition  
w

ith   the   key.
The "ECO" 
warning
 
lamp
 
comes
 o
n
 
in
 
the
 
instrument
 
panel
 
and
 
the
 
e

ngine
 
goes
 
into
 
standby:
-

w

ith a manual gearbox , at speeds below
12
 
mph
 
(20
 
km/h),
 
when
 
you
 
put
 
the
 
gear
 
l

ever into neutral, and you release the
clutch
 
pedal.
-

w

ith a 5 or 6-speed electronic gearbox ,
when
 
stationary
 
or
 
at
 
speeds
 
below
 
5
 
mph
 
(

8
 
km/h)
 
(depending
 
on
 
version),
 
when
 
y

ou
 
press
 
the
 
brake
 
pedal
 
or
 
put
 
the
 
gear
 
s

elector in position
n
.
A

 
time
 
counter
 
calculates
 
the
 
sum
 o

f
 
the
 
periods
 
in
 
STOP
 
mode
 
during
 a

 
journey.
 
It
 
rests
 
itself
 
to
 
zero
 
every
 t

ime
 
the
 
ignition
 
is
 
switched
 
on
 
with
 t

he
 
key. STOP
  mode   is   not   invoked   when:
-  t he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(

10 km/h)   since   the   last   engine   start   using  
t

he   key,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
Special cases: STOP mode not
available
The "ECO" warning   lamp   flashes   for  a
  few   seconds   then   goes   off.
This operation is perfectly normal.

Under-inflation detection
System which automatically checks the pressures of the tyres while driving.
T he   under-inflation   detection   system  
d

oes   not   replace   the   need   for   vigilance  
o

n   the   part   of   the   driver.
This
  system   does   not   avoid   the   need   to  
c

heck   the   tyre   pressures   (including   the  
s

pare   wheel)   every   month   as   well   as  
b

efore   a   long   journey.
Driving
  with   under-inflated   tyres  
i

mpairs   road   holding,   extends   braking  
d

istances   and   causes   premature  
t

yre wear, particularly under arduous
condition
  (high   loading,   high   speed,  
lon

g
 jo
urney).The inflation pressures defined for
your vehicle can be found on the tyre
pressure
  label.
See
  the   "Identification   markings"  
s

ection.
Tyre
  pressures   should   be   checked  
w

hen   the   tyres   are   "cold"   (vehicle  
s

topped   for   1   hour   or   after   a   journey   of  
l

ess   than   6   miles   (10   km)   at   moderate  
s

peeds).
Other wise
  (when   hot),   add   0.3   bar   to  
t

he   pressures   shown   on   the   label.
Driving
  with   under-inflated   tyres  
i

ncreases   fuel   consumption.
The
  system   monitors   the   pressures   in   the   four  
t

yres,   once   the   vehicle   is   moving.
It
  compares   the   information   given   by   the   four  
w

heel speed sensors with reference values,
which must be reinitialised ever y time the
tyre pressures are adjusted or a wheel
changed .
The
  system   triggers   an   alert   as   soon   as   it  
d

etects a drop in the inflation pressure of one
or
  more   tyres.

DS3_en_Chap08_info-pratiques_ed01-2015
Fuel tankFuel tank capacity: approximately 50 litres (petrol) or 46 litres (diesel) or 33 litres (LPg) ;
(dep ending on version: approximately 30 litres (petrol or di esel)).
Low fuel level
Filling
A label affixed to the inside of the flap reminds you   of   the   type   of   fuel   to   be   used   depending   on  
y

our
 eng
ine.
Additions
  of   fuel   must   be   of   at   least   7   litres,   in  
o

rder   to   be   registered   by   the   fuel   gauge.The
  key   cannot   be   removed   from   the  
l

ock   until   the   cap   is   refitted.
Opening
  the   filler   cap   may   create   a  
n

oise   caused   by   an   inrush   of   air.   This  
v

acuum   is   entirely   normal,   resulting  
f

rom   the   sealing   of   the   fuel   system.
To
  fill   the   tank   safely:
F

t
he engine must be switched off,
F

o
pen the fuel filler flap,
F
 
i
nsert   the   key   in   the   cap,   then   turn   it   to   the  
l

eft,F
 r emove   the   cap   and   hook   it   onto   the   clip  
l

ocated on the inside of the flap,
F
 
f
ill   the   tank,   but do not continue after the
3rd cut- off of the pump ;
  this   could   cause  
m

alfunctions.
When
  you   have   filled   the   tank:
F
 
p
ut   the   cap   back   in   place,
F
 
t
urn   the   key   to   the   right,   then   remove   it  
f

rom   the   cap,
F
 
c
lose   the   flap.
When the fuel tank minimum level is reached   this   warning   lamp   comes   on o

n   the   instrument   panel.   When   it   first
 c

omes   on   there   remains   approximately
5 litres
  of   fuel   in   the   tank.
With Stop & Start, never refuel with the
system  in   STOP   mode;   you   must   switch  
o

ff   the   ignition   with   the   key.
You
 
must   refuel   as   soon   as   possible   to   avoid  
r

unning   out   of   fuel.
If
 
you
 
run   out   of   fuel   (Diesel),   refer   also   to   the  
"

Checks"
 s
ection.

185
DS3_en_Chap08_info-pratiques_ed01-2015
Fuel used for petrol engines
The petrol engines are compatible with E10   bio-petrol   (containing   10   %   ethanol),  
c

onforming   to   European   standards   EN   228   and  
E

N
 1
5376.
E85
  type   fuels   (containing   up   to   85   %   ethanol)  
a

re   reserved   exclusively   for   vehicles   marketed  
f

or   the   use   of   this   type   of   fuel   (BioFlex  
v

ehicles).   The   quality   of   the   ethanol   must  
c

omply   with   European   standard   EN   15293.
Fuel used for diesel
engines
The Diesel engines are compatible with b
iofuels   which   conform   to   current   and   future  
E

uropean   standards   (Diesel   fuel   which  
c

omplies   with   standard   EN   590   mixed   with  
a

  biofuel   which   complies   with   standard  
E

N 14214)   available   at   the   pumps   (containing  
u

p   to   7   %   Fatty   Acid   Methyl   Ester).
B30 biofuel can be used in certain Diesel
engines.
  However,   this   use,   even   occasional,  
r

equires   strict   application   of   the   special  
s

ervicing   conditions.   Contact   a   CITROËN  
d

ealer   or   a   qualified   workshop.
The
  use   of   any   other   type   of   (bio)fuel  
(

vegetable   or   animal   oils,   pure   or   diluted,  
d

omestic   fuel...)   is   strictly   prohibited   (risk   of  
d

amage   to   the   engine   and   fuel   system).
For
 
the
 
DS
 
3
 
R ACING,
 
we
 
strongly
 
r

ecommend
 
the
 
use
 
of
 
98
 
RON
 
u

nleaded
 
petrol
 
to
 
ensure
 
optimum
 
o

peration
 
of
 
the
 
engine
 
(refer
 
to
 
the
 
l

abel
 
inside
 
the
 
fuel
 
filler
 
flap).
Practical information

DS3_en_Chap08_info-pratiques_ed01-2015
* According to country of sale.
Misfuel prevention (Diesel)*Mechanical device which prevents filling the tank of a Diesel vehicle with petrol. It avoids the risk of engine damage that can result from filling with the wrong   fuel.
Located
  in   the   filler   neck,   the   misfuel   prevention   device   appears   when   the   filler   cap   is   removed.
Operation
When a petrol filler nozzle is introduced into the
fuel  filler   neck   of   your   Diesel   vehicle,   it   comes  
i

nto   contact   with   the   flap.   The   system   remains  
c

losed   and   prevents   filling.
do n

ot persist but introduce a d
i
esel type
filler nozzle. It
  remains   possible   to   use   a   fuel   can   to  
f

ill   the   tank.
In   order   to   ensure   a   good   flow   of   fuel,  
d

o not place the nozzle of the fuel can
in direct contact with the flap of the
misfuel   prevention   device   and   pour  
s

l ow l y.
Travelling abroad
As Diesel fuel pump nozzles may b
e different in other countries, the
presence
  of   the   misfuel   prevention  
d

evice   may   make   refuelling   impossible.
Before
  travelling   abroad,   we  
r

ecommend   that   you   check   with   the  
C

ITROËN   dealer   network,   whether  
y

our vehicle is suitable for the fuel
pumps
  in   the   country   in   which   you   want  
t

o   travel.

187
DS3_en_Chap08_info-pratiques_ed01-2015
Running out of fuel (Diesel)If your vehicle has an HDi engine, the fuel system must be primed if you run out of fuel.
T his   system   consists   of   a   priming   pump   and   a   transparent   pipe   under   the   bonnet.
F
 
F
ill   the   fuel   tank   with   at   least   five   litres   of  
D

iesel.
F
 
O
pen   the   bonnet.
F
 
D
epending   on   version,   unclip   the   cover   to  
g

ain   access   to   the   priming   pump.
F
 
S
queeze   and   release   the   priming   pump  
u

ntil   resistance   is   felt   (could   be   from   the  
f

irst   application)   and   fuel   appears   in   the  
t

ransparent   pipe   with   the   green   connector.
F
 
O
perate   the   starter   until   the   engine   starts.
F
 
D
epending   on   version,   put   the   cover   back  
i

n   position   and   clip   it   in   place.
F
 
C
lose   the   bonnet.
BlueHdi 100 engines
F Fill  the   fuel   tank   with   at   least   five   litres   of  D
iesel.
F
 
S
witch   on   the   ignition   (without   starting   the  
e

ngine).
F

W
ait around 6 seconds and switch off the
ignition.
F
 
R
epeat   the   operation   10   times.
F
 
O
perate   the   starter   to   run   the   engine.
If
 
the
 
engine
 
does
 
not
 
start
 
at
 
the
 
first
 
a

ttempt,
 
do
 
not
 
try
 
again.
Operate
 
the
 
priming
 
pump
 
again,
 
then
 
t

he
 
starter.
Practical information