2015 Citroen DS3 instrument panel

DS3_en_Chap04_conduite_ed01-2015
F Apply  the   parking   brake.
F  W ith   a   manual   gearbox:   place   the   lever   in  
n

eutral   and   fully   depress   the   clutch   pedal.
F
 
W
ith   an   electronic   gearbox:   place   the   lever  
a

t position n  and   press   the   brake   pedal  
f

i r m l y.
F
 
W
ith   an   automatic   gearbox:   place   the   lever  
a

t position P   and   press   the   brake   pedal  
f

i r m l y.
F
 
I
nsert   the   key   in   the   ignition   switch;   the  
s

ystem   recognises   the   code.
F
 
U
nlock   the   steering   column   by  
s

imultaneously   turning   the   steering   and   the  
k

ey.
Starting the engine
In some circumstances, you may have to   apply   some   force   to   turn   the   steering  
w

heel   (wheels   on   lock   for   example).In
  wintry   conditions,   the   warning   lamp  
w

ill   stay   on   longer.   When   the   engine   is  
h

ot,   it   does   not   come   on.In   temperate   conditions,   do   not  
w

arm   the   engine   up   with   the   vehicle  
s

tationary,   but   move   off   straight   away  
a

nd   drive   at   moderate   engine   speeds.
If   the   engine   does   not   start   straight  a
way,   switch   the   ignition   off.   Wait   a  
f

ew   moments   before   trying   again.   If  
t

he   engine   does   not   start   after   a   few  
a

ttempts,   do   not   keep   trying:   you   risk  
d

amaging   the   starter   motor   and   the  
e

ngine.   Call   on   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.Never
  leave   the   engine   running   in  
a

n   enclosed   area   without   adequate  
v

entilation:
 in
ternal
 c
ombustion
 e

ngines   emit   toxic   exhaust   gases,  
s

uch   as   carbon   monoxide.   Danger   of  
i

ntoxication   and   death.   In   very   severe  
w

inter   conditions   (temperatures  b
elow -23°C),   it   is   necessary   to   allow  t
he   engine   to   run   for   4   minutes   before  
s

etting   off,   in   order   to   ensure   the  
c

orrect operation and durability of
the
  mechanical   components   of   your  
v

ehicle,   the   engine   and   gearbox.
F
 
W
ith   a   petrol   engine,   operate   the   starter  
m

otor   by   turning   the   key   to   position   3 until
the
  engine   starts,   without   pressing   the  
a

ccelerator   pedal.   Once   the   engine   starts,  
r

elease   the   key.
F
 
W
ith   a   Diesel   engine,   turn   the   key   to  
p

osition 2 ,
  ignition   on,   to   operate   the  
eng

ine
 p
reheating
 s
ystem. Wait
  until   this   warning   lamp   goes   off
 i

n   the   instrument   panel,   then   operate
 t

he   starter   motor   by   turning   the   key   to
 p

osition
3
 
until   the   engine   starts,   without
 p

ressing   the   accelerator   pedal.   Once
 t

he   engine   starts,   release   the   key.

107
DS3_en_Chap04_conduite_ed01-2015
display in the instrument panel
n. Neutral
R. R everse
1 2 3 4 5 / 6.
  Gears   in   manual   mode.
AUTO.
 

 
T
his   comes   on   when   automated   mode  
i

s   selected.   It   goes   off   when   changing  
t

o   manual   mode.
Moving off
F Select position n.
F  P ress   the   brake   pedal   fully.
F
 
S
tart   the   engine.
n

  appears   in   the   instrument   panel.
If
  the   engine   does   not   start:
-
If
n
  is   flashing   in   the   instrument  
p

anel,   move   the   gear   selector   to  
p

osition A, then to position
n
.F

 S elect   automated   mode   (position   A
), m
anual   mode   (position   M)   or   reverse  
(

position
 R)
AU

TO and 1 , 1 or R appear in the
instrument
 pan

el.
F
 
R
elease   the   parking   brake.
F
 
P
rogressively   take   your   foot   off   the   brake  
ped

al.
Depending
  on   the   type   of   electronic  
g

earbox,   the   vehicle   may   move   off   on  
i

ts   own.
For
  more   information,   refer   to   the  
"

Creep   function"   section.
Do
  not   press   the   brake   and   clutch  
p

edals   simultaneously.   This   can   cause  
r

apid   clutch   wear.
F
 
A
ccelerate   away.
-
 
I
f   this   warning   lamp  
c

omes   on,   accompanied  
b

y   an   audible   signal   and  
t

he  
d
isplay  
o
f  
a
 
m
essage,  
p

ress   firmly   on   the   brake  
ped

al.
driving

DS3_en_Chap04_conduite_ed01-2015
Creep function
(depending on equipment)
This function allows the vehicle to be
manoeuvred  more   easily   at   low   speeds   (when  
p

arking,   in   traffic   jams...).
With
  the   gear   selector   in   position   A, M or R ,
the vehicle moves as soon as you take your
foot off the brake pedal , at low speed and
with
  the   engine   at   idle.
Automated mode
AUTO and   the   gear   engaged   appear  i
n   the   instrument   panel.
The
 
gearbox   then   operates   in   auto-adaptive  
m

ode,
 
without   any   action   on   the   part   of   the  
d

river.
 
It
 
continuously   selects   the   most   suitable  
g

ear
 
taking   account   of:
-
 
o

ptimisation   of   fuel   consumption,
-
 
d

riving   style,
-

r

oad conditions,
-
 
v

ehicle   load.
For
 
optimum   acceleration,   when   overtaking  
a

nother
 
vehicle   for   example,   press   the  
a

ccelerator pedal fully down, beyond the point
of
 
resistance. You
  can   change   mode   at   any   time   by  
m

oving   the   gear   selector   from   A to M or
the
  other   way   round.
The
 
creep
 
function
 
may
 
be
 
temporarily
 
u

navailable
 
if
 
the
 
clutch
 
temperature
 
is
 
t

oo
 
high
 
or
 
the
 
slope
 
too
 
steep.
Do not leave children unsupervised
inside
 
the
 
vehicle
 
when
 
the
 
engine
 
is
 
r

unning. F

Sel

ect position A
.
Never   select   neutral   (position  n
)
  when  
m

oving.
Temporary control of gear
changing
You can temporarily take over control of gear c hanges   using   the   steering   mounted   "+" and
"-"
control
  paddles:   if   the   engine   speed   allows,   the
 g

ear   change   is   carried   out.
This function allows you to anticipate certain
situations
 
s
uch  
a
s  
ov
ertaking  
a
nother  
v
ehicle  
o
r  
a

pproaching   a   bend.
After
  a   few   moments   without   any   action   on   the  
p

addles,   the   gearbox   resumes   control   of   gear  
c

hanging
 a
utomatically.

109
DS3_en_Chap04_conduite_ed01-2015
The gear change requests are only carried out if   the   engine   speed   permits.
It is not necessary to release the accelerator
pedal
  during   gear   changes.
When
  braking   or   slowing   down,   the   gearbox  
c

hanges   down   automatically   so   that   the   vehicle  
p

icks   up   in   the   right   gear.
Under
  full   acceleration,   the   change   up   will   not  
t

ake   place   unless   the   driver   operates   the   gear  
s

elector   or   steering   mounted   control   paddle  
(

unless   the   engine   is   close   to   its   maximum  
s

peed).
Reverse
To engage reverse, the vehicle must be immobilised   with   your   foot   on   the   brake.
F

Sel
ect position R .
Stopping the vehicle
Before switching off the engine:
-  c hange   to   position  n to be in neutral,


or
-
 
l
eave   the   vehicle   in   gear;   in   this   case   the  
v

ehicle   cannot   be   moved.
Manual mode
F Select position M.
The   gears   engaged   appear   in  
s

uccession   in   the   instrument   panel.
You
  can   change   mode   at   any   time   by  
m

oving   the   gear   selector   from   A to M or
the
  other   way   round.
Never
  select   neutral   (position  n
)
  when  
m

oving. There
  is   an   audible   signal   on  
enga

gement
 o
f
 r
everse.For
  all   parking   situations,   you   must
apply the parking brake
 

to   immobilise  
t

he   vehicle.
When
  immobilising   the   vehicle   with   the  
e

ngine   running,   you   must   put   the   gear  
s

elector   into   the   neutral   (position  n
).
B

efore   doing   anything   under   the  
b

onnet,   ensure   that   the   gear   selector  
i

s   in   neutral   (position  n
)
  and   that   the  
p

arking   brake   is   applied.
At
  low   speed,   if   reverse   gear   is   requested,  
t

he n  warning   lamp   flashes   and   the   gearbox  
g

oes   into   neutral   automatically.
To
  engage   reverse,   put   the   gear   selector   into  
p

osition n
, t
hen to position R.
driving

DS3_en_Chap04_conduite_ed01-2015
Operating fault
With the ignition on, if this warning lamp   comes   on   and   AUTO flashes,
accompanied
  by   an   audible   signal   and   a  
m

essage
 
in
  the   multifunction   screen,   this  
i

ndicates
 
a
 
gearbox   fault.
Have
 
it
 
checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w

orkshop.
Reinitialisation
(5-speed electronic
gearbox)
In exceptional circumstances, the g earbox   may   need   an   automatic  
r

einitialisation:   starting   and   gear  
c

hanging   are   no   longer   possible.
AUTO and - - appear in the
instrument
 pan

el.
AUTO and - -   appear   in   the   instrument   panel.
F Select position n.
F  P ress   the   brake   pedal.
F

W
ait for around 30 seconds until n or a
gear
  appears   in   the   instrument   panel.
F
 
M
ove   the   gear   selector   to   position   A, then
to position
n
.
F

 
W
ith   your   foot   still   on   the   brake   pedal,   start  
t

he
 eng
ine.
The
  gearbox   is   operational   again.
Following
  disconnection   of   the   battery,   it   is  
n

ecessary   to   reinitialise   the   gearbox.
F  
S
witch   on   the   ignition.
Follow   the   procedure   described   above.

DS3_en_Chap04_conduite_ed01-2015
When you move the selector in the gate to select   a   position,   the   corresponding   indicator   is  
d

isplayed   in   the   instrument   panel.
P.
 Pa

rk
R.
R

everse
n. N

eutral
d

.
 D
rive   (Automatic   driving)
S.
Sport
 pro
gramme
T .
Snow
 pro
gramme
1 2 3 4.
  
G
ears   engaged   during   manual  
ope

ration
-.
 I

nvalid   value   during   manual   operation
displays in the instrument panel
Foot on brake
F Press  the   brake   pedal   when   this  i
ndicator   lamp   is   displayed   in   the  
i

nstrument   panel   (e.g.:   starting  
t

he
 eng
ine).
Moving off
If position n is selected inadvertently
w hile   driving,   allow   the   engine   to  
r

eturn to idle then select position d to
accelerate.
If
  the   ambient   temperature   is  
b

elow -23°C,   the   engine   should   be   left  
a

t   idle   for   four   minutes,   to   ensure   the  
c

orrect   operation   and   life   of   the   engine  
an

d
 g
earbox. When
  the   engine   is   running   at   idle,   with  
t

he   brakes   released,   if   position   R
, d or
M   is   selected,   the   vehicle   moves   even  
w

ithout   the   accelerator   being   pressed.
When   the   engine   is   running,   never  
l

eave children in the vehicle without
supervision.
When   carrying   out   maintenance   with  
t

he   engine   running,   apply   the   parking  
b

rake   and   select   position   P
.
F
 
A

pply   the   parking   brake.
F

Sel
ect position P or n
.
F

 
S

tart   the   engine.
If this procedure is not followed, there is an
audible   signal,   accompanied   by   the   display   of  
a

n
 
warning   message.
F
 
W
ith   the   engine   running,   press   the   brake  
ped

al.
F
 
R

elease   the   parking   brake.
F

Sel
ect position R
, d or M
.
F
 
G

radually   release   the   brake   pedal.
The
 
vehicle   moves   off   immediately.

11 3
DS3_en_Chap04_conduite_ed01-2015
Automatic operation
F Select position d for automatic c hanging o
f   the   four   gears.
The
  gearbox   then   operates   in   auto-adaptive  
m

ode,   without   any   intervention   on   the   part  
o

f   the   driver.   It   continuously   selects   the   most  
s

uitable   gear   according   to   the   style   of   driving,  
t

he profile of the road and the load in the
vehicle.
For
  maximum   acceleration   without   touching  
t

he selector, press the accelerator pedal down
fully
  (kick   down).   The   gearbox   changes   down  
a

utomatically   or   maintains   the   gear   selected  
u

ntil   the   maximum   engine   speed   is   reached.
On
  braking,   the   gearbox   changes   down  
a

utomatically   to   provide   efficient   engine  
b

raking.
If you release the accelerator sharply, the
gearbox
  will   not   change   to   a   higher   gear   for  
s

afety   reasons.
Never select position
n while the
vehicle
  is   moving.
Never select positions P or R unless
the
  vehicle   is   completely   stationary.
Sport and snow
programmes
These two special programmes supplement the automatic   operation   in   very   specific   conditions  
o

f   use.
Sport programme "S"
F Press button "S" ,   after   starting   the   engine.
The   gearbox   automatically   favours   a   dynamic  
s

tyle   of   driving.
S
  appears   in   the   instrument   panel.
Snow programme "T"
F Press button " T",   after   starting   the   engine.
The   gearbox   adapts   to   driving   on   slippery  
r

oads.
This
  programme   improves   starting   and   drive  
w

hen   traction   is   poor.
T
  appears   in   the   instrument   panel.
Return to standard
automatic operation
F At  any   time,   press   the   button   selected  a
gain   to   quit   the   programme   engaged   and  
r

eturn   to   auto-adaptive   mode.
driving

DS3_en_Chap04_conduite_ed01-2015
Stop & StartThe Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine   restarts   automatically   -   START   mode   -   as   soon   as   you   want   to   move   off.   The   restart   takes   place   instantly,   quickly   and   silently.
Per fect
  for   urban   use,   the   Stop   &   Start   system   reduces   fuel   consumption   and   exhaust   emissions   as   well   as   the   noise   level   when   stationary.
Operation
going into engine STOP mode
For your comfort, during parking manoeuvres,   STOP   mode   is   not  
a

vailable for a few seconds after
coming
  out   of   reverse   gear.
STOP
  mode   does   not   affect   the  
f

unctionality of the vehicle, such as for
example,
  braking,   power   steering...
Never
  refuel   with   the   engine   in   STOP  
m

ode;   you   must   switch   off   the   ignition  
w

ith   the   key.
The "ECO" 
warning
 
lamp
 
comes
 o
n
 
in
 
the
 
instrument
 
panel
 
and
 
the
 
e

ngine
 
goes
 
into
 
standby:
-

w

ith a manual gearbox , at speeds below
12
 
mph
 
(20
 
km/h),
 
when
 
you
 
put
 
the
 
gear
 
l

ever into neutral, and you release the
clutch
 
pedal.
-

w

ith a 5 or 6-speed electronic gearbox ,
when
 
stationary
 
or
 
at
 
speeds
 
below
 
5
 
mph
 
(

8
 
km/h)
 
(depending
 
on
 
version),
 
when
 
y

ou
 
press
 
the
 
brake
 
pedal
 
or
 
put
 
the
 
gear
 
s

elector in position
n
.
A

 
time
 
counter
 
calculates
 
the
 
sum
 o

f
 
the
 
periods
 
in
 
STOP
 
mode
 
during
 a

 
journey.
 
It
 
rests
 
itself
 
to
 
zero
 
every
 t

ime
 
the
 
ignition
 
is
 
switched
 
on
 
with
 t

he
 
key. STOP
  mode   is   not   invoked   when:
-  t he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(

10 km/h)   since   the   last   engine   start   using  
t

he   key,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
Special cases: STOP mode not
available
The "ECO" warning   lamp   flashes   for  a
  few   seconds   then   goes   off.
This operation is perfectly normal.