2015 CITROEN DS3 CABRIO DAG turn signal

35
DS3_en_Chap01_controle-de-marche_ed01-2014
With the engine running, when the needle is:
- i n zone A ,
  the   temperature   is   correct,
-

i
n zone B,   the   temperature   is   too   high;  
t

he central STOP
 
warning   lamp   and   the  
m

aximum   temperature   warning   lamp 1
come
  on   in   red,   accompanied   by   an  
a

udible   signal   and   a   message   in   the  
m

ultifunction
 s
creen.
You must stop as soon as it is safe to do so.
Wait
  a   few   minutes   before   switching   off   the  
e

ngine.
Contact a CITR
oË

N dealer or a qualified
workshop.
coolant temperature indicator
After driving for a few minutes, the temperature a nd   pressure   in   the   cooling   system   increase.
To
  top   up   the   level:
F
 
w
ait   for   the   engine   to   cool   down,
F

u
nscrew the cap by two turns to allow the
pressure to drop,
F
 
w
hen   the   pressure   has   dropped,   remove  
t

he cap,
F
 
t
op   up   the   level   to   the   "MA X"   mark.
Monitoring

DS3_en_Chap06_conduite_ed01-2014
When you move the lever in the gate to select a  position,   the   corresponding   indicator   is  
d

isplayed   in   the   instrument   panel.
P.
 Pa

rk
R.
R

everse
N.
N

eutral
d

.
 D
rive   (Automatic   driving)
S.
Sport
 pro
gramme
T .
Snow
 pro
gramme
1 2 3 4.
  
G
ears   engaged   during   manual  
ope

ration
-.
 I

nvalid   value   during   manual   operation
displays in the instrument panel
Foot on brake
F Press  the   brake   pedal   when   this  i
ndicator   lamp   is   displayed   in   the  
i

nstrument   panel   (e.g.:   starting  
t

he
 eng
ine).
Moving off
If position N is selected inadvertently
while  driving,   allow   the   engine   to  
r

eturn to idle then select position d to
accelerate.
If
  the   ambient   temperature   is   below  
-

23°C,   the   engine   should   be   left   at   idle  
f

or   four   minutes,   to   ensure   the   correct  
o

peration   and   life   of   the   engine   and  
g

earbox. When
  the   engine   is   running   at   idle,   with  t
he   brakes   released,   if   position   R
, d or
M   is   selected,   the   vehicle   moves   even  
w

ithout   the   accelerator   being   pressed.
When
  the   engine   is   running,   never  
l

eave children in the vehicle without
supervision.
When
  carrying   out   maintenance   with  
t

he   engine   running,   apply   the   parking  
b

rake   and   select   position   P.
F
 
A

pply   the   parking   brake.
F

Sel
ect position P or N
.
F
 
S

tart   the   engine.
If this procedure is not followed, there is an
audible   signal,   accompanied   by   the   display   of  
a

n
 
warning   message.
F
 
W
ith   the   engine   running,   press   the   brake  
ped

al.
F
 
R

elease   the   parking   brake.
F

Sel
ect position R
, d or M
.
F
 
G

radually   release   the   brake   pedal.
The
 
vehicle   moves   off   immediately.

DS3_en_Chap06_conduite_ed01-2014
There is a risk of damage to the gearbox:
- i f you press the accelerator and
brake
  pedals   at   the   same   time,
-
 
i
f   you   force   the   movement   of   the  
g

ear   lever   from   the   P position to
another position when the battery
is
  flat.
To
  reduce   fuel   consumption   when   at
 a

  prolonged   standstill   with   the   engine
 r

unning   (traffic   jam...),   put   the   gear   lever   in
 t

he N
 

position   and   apply   the   parking   brake.
If the lever is not in position P
,
when the driver's door is opened or
approximately
 
45
 
seconds
 
after
 
the
 
i

gnition
 
is
 
switched
 
off,
 
a
 
warning
 
m

essage
 
appears
 
in
 
the
 
screen.
F

R

eturn the lever to position P ;
 
the
 
m

essage
 d

isappears.
When
 
driving
 
on
 
flooded
 
roads
 
or
 
when
 
c

rossing
 
a
 
ford,
 
proceed
 
at
 
walking
 
p

ace.
Operating fault
Manual operation
When the ignition is on, the lighting o f   this   warning   lamp,   accompanied  
b

y
 
an
 
audible   signal   and   a   message   in   the  
m

ultifunction   screen,   indicates   a   gearbox   fault.
In
 
this
 
case,   the   gearbox   switches   to   back-up  
m

ode
 
and
 
is   locked   in   3rd   gear.   You   may   feel  
a

 
substantial   knock   when   changing   from   P
to R
 
and
 
from   N to R .
  This   will   not   cause   any  
d

amage
 
to
 
the   gearbox.
Do
 
not
 
exceed   60   mph   (100   km/h),   local   speed  
r

estrictions
 p
ermitting.
Contact a CITR
oË

N dealer or a qualified
workshop
 
as   soon   as   possible.
F

Sel

ect position M for sequential
 c

hanging
 o

f
 
the
 
four
 
gears.
F

P

ush the lever towards the +
 
sign
 
to
 
c

hange
 
up
 
a
 
gear.
F

P

ull the lever towards the -
 
sign
 
to
 
change
 
d

own
 
a
 
gear.
It
 
is
 
only
 
possible
 
to
 
change
 
from
 
one
 
gear
 
to
 
a

nother
 
if
 
the
 
vehicle
 
speed
 
and
 
engine
 
speed
 
p

ermit;
 
other wise,
 
the
 
gearbox
 
will
 
operate
 
t

emporarily
 
in
 
automatic
 
mode. This
 
symbol
 
is
 
displayed
 
if
 
a
 
gear
 
i

s
 
not
 
engaged
 
correctly
 
(selector
 
b

etween
 
two
 
positions).
d

 
disappears
 
and
 
the
 
gears
 
e

ngaged
 
appear
 
in
 
succession
 
in
 
the
 
in

strument
 pan

el.
Stopping the vehicle
Before switching off the engine, you can engage p osition P or N 
to   place   the   gearbox   in   neutral.
In
  both   cases,   apply   the   parking   brake   to
 i

mmobilise   the   vehicle.
Invalid value during manual
operation
If the engine speed is too low or too high, the gear   selected   flashes   for   a   few   seconds,   then  
t

he   actual   gear   engaged   is   displayed.
It
  is   possible   to   change   from   position  d
(automatic)
  to   position   M   (manual)   at   any   time.
When
  the   vehicle   is   stationary   or   moving  
v

ery   slowly,   the   gearbox   selects   gear   M1
automatically.
The
  sport   and   snow   programmes   do   not  
o

perate   in   manual   mode.

DS3_en_Chap07_visibilite_ed01-2014
The sidelamps and dipped beam headlamps are   switched   on   automatically,   without   any  
a

ction on the part of the driver, when a low level
of
  external   light   is   detected   or   in   certain   cases  
o

f   activation   of   the   windscreen   wipers.
As
  soon   as   the   brightness   returns   to   a  
s

ufficient level or after the windscreen wipers
are
  switched   off,   the   lamps   are   switched   off  
au

tomatically.
Automatic illumination of headlamps
Activation
F Turn   ring   to   the   "AUTO"  position.   The  a
utomatic   illumination   of   headlamps   is  
a

ccompanied   by   a   message   in   the   screen.
deactivation
F Turn  ring   to   a   position   other   than   "AUTO".  D
eactivation   is   accompanied   by   a   message  
i

n   the   screen.
Association with the automatic
"Guide-me-home" lighting
Association with the automatic illumination of headlamps   provides   "guide-me-home"   lighting  
w

ith   the   following   additional   options:
-
 
s
election   of   the   lighting   duration   to   15,  
30 or 60 seconds in the functions that can
be
  set   in   the   vehicle   configuration   menu  
(

except   in   the   case   of   the   monochrome  
s

creen   A,   for   which   the   duration   is   set:  
60 seconds),
-
 
a
utomatic   activation   of   "guide-me-home"  
l

ighting   when   automatic   illumination   of  
h

eadlamps   is   in   operation.
Operating fault
In the event of a fault with the
sunshine  sensor,   the   lighting  
c

ome
 
on,
 
this   warning   lamp   is   displayed   in   the  
i

nstrument
 
panel   and/or   a   message   appears   in  
t

he
 
screen,
  accompanied   by   an   audible   signal.
Contact a CITR
oË

N dealer or a qualified
workshop.
In
 
fog   or   snow,   the   sunshine   sensor  
m

ay
 
detect   sufficient   light.   Therefore,  
t

he
 
lighting   will   not   come   on  
au

tomatically.
Do not cover the sunshine sensor,
coupled with the rain sensor and
located in the centre of the windscreen
behind
  the   rear   view   mirror;   the  
a

ssociated   functions   would   no   longer  
be c

ontrolled.

197
DS3_en_Chap10_info-pratiques_ed01-2014
In the event of a fault with the the ScR emissions control system
If it is a temporary fault, the alert d
isappears   once   the   exhaust   gas  
e

missions   return   to   normal.
A
 
system
 
that
 
prevents
 
engine
 
s

tarting
 
is
 
activated
 
automatically
 
f

rom
 
650 miles
 
(1
 
100
 
km)
 
after
 
c

onfirmation
 
of
 
a
 
fault
 
with
 
the
 
SCR
 
e

missions
 
control
 
system.
 
Have
 
the
 
s

ystem
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
o

r
 
a
 
qualified
 
workshop
 
as
 
soon
 
as
 
p

ossible.
In the event of the detection of a fault
du
ring an authorised driving phase (between
650 miles and 0 miles) (1 100 km and 0 km)
When
  switching   on   the   ignition,   the   UREA,  
S

ERVICE   and   diagnostic   warning   lamps   comes  
o

n,
 
accompanied   by   an   audible   signal   and   the  
d

isplay
 o
f
 a m
essage
 "
Emissions
 f
ault"
 t
o
 s
ignal
 a

 
fault
  with   the   emissions   control   system.If   a   fault   with   the   SCR   system   is   confirmed  
(

after   30   miles   (50   km)   covered   with   the  
p

ermanent   display   of   the   message   signalling  
a

  fault),   when   switching   on   the   ignition,   the  
S

ERVICE
 an
d
 e
ngine
 d
iagnostic
 w
arning
 lam
ps
 c

ome   on   and   the   UREA   warning   lamp   flashes,  a
ccompanied   by   an   audible   signal   and   the  d
isplay   of   a   message   (e.g.:   "Emissions   fault:  
S

tarting   prevented   in   150   miles")   indicating   the  
r

emaining   range   express   in   miles   or   kilometres.
While
  driving,   the   message   is   displayed   every  
3

0   seconds   while   the   fault   with   the   SCR   system  
p

ersists.
You
  should   go   to   a   CITROËN   dealer   or   a  
q

ualified   workshop   as   soon   as   possible.
ot

her wise, you will not be able to restart your
engine.
Practical information

201
DS3_en_Chap10_info-pratiques_ed01-2014
Important: if your vehicle's a
dblu e® tank is completely empty - w
hich
 
is
  confirmed   by   the   alert  
m

essages   and   the   impossibility   of  
s

tarting
 
the   engine,   you   must   add   at  
l

east
 
3.8   litres   (so   two   1.89   litre   bottles).If any additive is split or splashed, wash
immediately
  with   cold   water   or   wipe  
w

ith   a   damp   cloth.
If the additive has crystallised, clean it
off   using   a   sponge   and   hot   water.Important:
 i
n the event of a top-up after
a breakdown because of a lack of
additive ,   signalled   by   the   message   "Top
 u

p   emissions   additive:   Starting   prevented",
 y

ou   must   wait   around   5   minutes   before
 s

witching  
o
n  
t
he  
i
gnition,  
w
ithout opening
the driver's door, locking the vehicle
or introducing the key into the ignition
switch .
Switch   on   the   ignition,   then,   after
 1

0 seconds,   start   the   engine.
F
o
b

tain a bottle of a
dbl
ue
®. After first c
hecking
 
the
 
use-by
 
date,
  read   carefully  
t

he instructions on use on the label before
pouring
 
the
 
contents
 
of
 
the   bottle   into   your  
v

ehicle's
a
d
blu

e
® tank. N ever dispose of a
dbl
ue
® additive
bottles
 
in
 
the
 
household
 
waste.   Place  
t

hem
 
in
 
a
 
special
 
container   provided  
t

his
 
purpose
 
or
 
take
 
them
  to   your  
d

ealer.
F
 
A

fter
 
emptying
 
the
 
bottle,
 
wipe
 
away
 
any
 
s

pillage
 
around
 
the
 
tank
 
filler
 
using
 
a
 
damp
 
c

loth.
F
 
R

efit
 
the
 
blue
 
cap
 
to
 
the
 
tank
 
and
 
turn
 
it
 
a


6
th of a turn clockwise, to its stop.
F
 R
efit   the   black   cap   and   turn   it   a   quarter   of  
a

 
turn   clockwise   without   pressing.   Ensure  
t

hat the indicator on the cap lines up with
the
 
indicator   on   the   support.
F
 
D

epending   on   equipment,   return   the   spare  
w

heel   and/or   the   storage   box   to   the   bottom  
o

f
 
the   boot.
F
 
R

efit   the   boot   carpet   and   close   the   tailgate.
Practical information

07
315
DS3_en_Chap13b_RT6-2-8_ed01-2014
Press the button on the numerical keypad to recall a preset  station.
Or
  press   then   turn   the   thumb   wheel   at   the   steering  
mounted

  controls.
Presetting a station
After selecting a station, press one of the buttons on  the   numerical   keypad   for   2   seconds   to   preset   the  
current

  station.
An
  audible   signal   confirms   that   the   station   has   been  
preset. Press

RA d IO.
Activate / d
eactivate R d S
RDS, if activated, allows you to continue listening to the same station
  by   automatic   retuning   to   alternative   frequencies.   However,  
in

  certain   conditions,   coverage   of   an   RDS   station   may   not   be  
assured

  throughout   the   entire   country   as   radio   stations   do   not  
cover

  100   %   of   the   territory.  
This
  explains   the   loss   of   reception   of  
the

  station   during   a   journey.
Select "Guidance options " then
confirm.
a

ctivate or deactivate "R d S" then
confirm.
RAdIO