2015 CITROEN DS3 CABRIO DAG bonnet

39
DS3_en_Chap01_controle-de-marche_ed01-2014
on vehicles fitted with an electric oil level
indicator,  information   on   the   oil   level   is  
d

isplayed   in   the   instrument   panel   for   a   few  
s

econds   when   the   ignition   is   switched   on,   after  
t

he   service   information.
Engine oil level indicator*
The level shown will only be correct
if  the   vehicle   is   on   level   ground   and  
t

he   engine   has   been   off   for   more   than  
3

0 minutes.
Oil level correct
Oil level low
This is indicated by the flashing of " O I L" ,
a ccompanied   by   illumination   of   the   service  
w

arning   lamp,   an   audible   signal   and   a  
m

essage.
If
  the   low   oil   level   is   confirmed   by   a   check   using  
t

he   dipstick,   the   level   must   be   topped   up   to  
p

revent   damage   to   the   engine.
Refer
  to   the   "Checking   levels"   section.
Oil level indicator fault
This is signaled by the flashing of "OIL- -".
C ontact a CITRoË N dealer or a qualified
workshop.
In the event of a fault with the electric oil level
indicator,
  the   engine   oil   level   is   no   longer  
mon

itored.
While
  the   system   is   faulty,   you   should   check  
t

he   engine   oil   level   using   the   manual   dipstick  
l

ocated   under   the   bonnet.
Refer
  to   the   "Checking   levels"   section.
*
  Depending   on   version.
Monitoring

DS3_en_Chap07_visibilite_ed01-2014
Travelling abroad
LEd / Xenon front lamps
For motoring in countries that drive on the other s
ide of the road, it is necessary to adapt the
adjustment
  of   the   dipped   beams   so   as   to   not  
d

azzle   the   drivers   of   approaching   vehicles.
F
 
R
aise   the   bonnet   for   access   to   the   adjuster  
(

one   adjuster   per   headlamp).
F
 
I
nsert   a   suitable   allen   key   (not   supplied)  
i

nto   the   hexagonal   head   of   the   adjuster.
F
 
T
urn   the   allen   key   half   a   turn   clockwise.
Headlamp adjustment
To avoid causing a nuisance to other road u
sers,   the   height   of   the   headlamps   should   be  
a

djusted   in   relation   to   the   load   in   the   vehicle.
0.
 
D
river   only   or   driver   +   front   passenger.
-.
 I

ntermediate
 s
etting.
1.
 5

  people.
-.
 
5
  people   +   load   in   the   boot.
2.
 D

river   only   +   maximum   authorised   load   in  
t

he   boot.
This
  position   is   sufficient   to   avoid   causing  
d

azzle.
Higher
  settings   may   limit   the   spread   of   light  
f

rom   the   headlamps.
The
  initial   setting   is   position   "0". On
  your   return,   don't   forget   to   return  
y

our   headlamps   to   their   initial   setting,  
b

y   carrying   out   these   operations   in  
r

everse
 o
rder.

DS3_en_Chap07_visibilite_ed01-2014
Operating fault
If an automatic wiping fault occurs, the wipers will   operate   in   intermittent   mode.
Have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop. To retain the effectiveness of the flat
wiper
  blades,   it   is   advisable   to:
-
 
h
andle   them   with   care,
-
 
c
lean   them   regularly   using   soapy  
w

ater,
-
 
n
ot   use   them   to   hold   a   sheet   of  
c

ardboard   against   the   windscreen,
-
 
r
eplace   them   at   the   first   signs   of  
w

e a r.
Do
  not   cover   the   rain   sensor,   linked  
w

ith the sunshine sensor and located in
the centre of the windscreen behind the
rear
  view   mirror.
Switch
  off   the   automatic   wiping   when  
u

sing   an   automatic   car   wash.
In winter, it is advisable to wait until the
windscreen
  is   completely   clear   of   ice  
b

efore   activating   the   automatic   wiping.This position allows the wiper blades to
be
  lifted   for   winter   parking,   cleaning   or  
r

eplacement   without   damaging   the   bonnet.
In
  the   minute   following   switching   off   of   the  
i

gnition,   any   action   on   the   wiper   stalk   positions  
t

he   wipers   vertically.
To
  park   the   wipers   after   this   has   been   done,
 s

witch   on   the   ignition   and   operate   the   wiper   stalk.
Vertical windscreen wiper
position

159
DS3_en_Chap08_securite_ed01-2014
Operating limits
The system only detects vehicles that are stationary   or   moving   in   the   same   direction   as  
y

our   vehicle.
It
  does   not   detect   small   vehicles  
(

bicycles,   motorcycles),   pedestrians   or  
a

nimals,   nor   non-reflective   stationary  
ob

jects. In difficult weather conditions (very
heavy
  rain,   snow,   fog,   hail...),   braking  
d

istances increase, which can reduce
the
  ability   of   the   system   to   avoid   a  
c

ollision.
The
  driver   must   therefore   remain  
par

ticularly
 v
igilant.
Never
  leave   accumulations   of   snow   or  
a

ny   object   projecting   above   the   bonnet  
o

r   in   front   of   the   roof:   this   might   fall   into  
t

he field of vision of the sensor and
generate
  a   detection.
The
  system   is   not   triggered   or   is   interrupted   if  t
he d river:
-
 
a
ccelerates   strongly
-
 
o
r   turns   the   steering   wheel   suddenly  
(

avoiding
 m
anoeuvre).
Safety

193
DS3_en_Chap10_info-pratiques_ed01-2014
Running out of fuel (Diesel)If your vehicle is fitted with an HDI engine, the fuel system must be primed if you run out of fuel.
T his   system   consists   of   a   priming   pump   and   a   transparent   pipe   under   the   bonnet.
F
 
F
ill   the   fuel   tank   with   at   least   five   litres   of  
D

iesel.
F
 
O
pen   the   bonnet.
F
 
D
epending   on   version,   unclip   the   cover   to  
g

ain   access   to   the   priming   pump.
F
 
S
queeze   and   release   the   priming   pump  
u

ntil   resistance   is   felt   (could   be   from   the  
f

irst application) and fuel appears in the
transparent
  pipe   with   the   green   connector.
F
 
O
perate   the   starter   until   the   engine   starts.
F
 
D
epending   on   version,   put   the   cover   back  
i

n   position   and   clip   it   in   place.
F
 
C
lose   the   bonnet.
BlueHdi 100 engines
F Fill  the   fuel   tank   with   at   least   five   litres   of  D
iesel.
F
 
S
witch   on   the   ignition   (without   starting   the  
e

ngine).
F

W
ait around 6 seconds and switch off the
ignition.
F
 
R
epeat   the   operation   10   times.
F
 
O
perate   the   starter   to   run   the   engine.
If
 
the
 
engine
 
does
 
not
 
start
 
at
 
the
 
first
 
a

ttempt,
 
do
 
not
 
try
 
again.
Operate
 
the
 
priming
 
pump
 
again,
 
then
 
t

he
 
starter.
Practical information

231
DS3_en_Chap10_info-pratiques_ed01-2014
batteryProcedure for charging your battery when it is flat or for starting the engine using another battery.T he   battery   is   located   under   the   bonnet.
To
  gain   access   to   it:
F
 
o
pen   the   bonnet   using   the   interior   release  
l

ever,   then   the   exterior   safety   catch,
F

s
ecure the bonnet stay,
F
 
l
ift   the   plastic   cover   on   the   (+)   terminal.
Access to the batteryAfter refitting the battery by a CITRoË N dealer or a qualified
workshop,
  the   Stop   &   Start   system  
w

ill only be active after a continuous
period
  of   immobilisation   of   the   vehicle,  
a

  period   which   depends   on   the   climatic  
c

onditions   and   the   state   of   charge   of  
t

he   battery   (up   to   about   8   hours).
The presence of this label, in particular
with
 
the
 
Stop
 
&
 
Start
 
system,
 
indicates
 
t

he use of a 12 V lead-acid battery with
special
 t

echnology
 a

nd
 s

pecification;
 t

he
 
involvement
 
of
 
a
 
CITROËN
 
dealer
 
o

r
 
a
 
qualified
 
workshop
 
is
 
essential
 
w

hen
 
replacing
 
or
 
disconnecting
 
the
 
b

attery.
Failure
 
t

o
 
o

bserve
 
t

his
 
r

ecommendation
 
m

ay
 
cause
 
premature
 
wear
 
of
 
the
 
b

attery.
Practical information

235
DS3_en_Chap10_info-pratiques_ed01-2014
Changing a front or rear wiper bladeProcedure for replacing a worn wiper blade with a new one without the use of tools.
Before removing a front
wiper blade
F Within  one   minute   after   switching   off   the  i
gnition,   operate   the   wiper   stalk   to   position  
t

he   wiper   blades   in   the   vertical   position.
This
  position   must   be   used   in   order   to   avoid  
d

amaging   the   wiper   blade   and   the   bonnet.
Removal
F Raise  the   corresponding   wiper   arm.
F  U nclip   the   wiper   blade   and   remove   it.
Fitting
F At  the   front,   check   the   size   of   the   wiper  b
lade as the shorter blade is fitted to the
passenger
  side   of   the   vehicle.
F
 
P
ut   the   corresponding   new   wiper   blade   in  
p

lace   and   clip   it.
F
 
F
old   down   the   wiper   arm   carefully.
After fitting a front wiper
blade
F Switch  on   the   ignition.
F  O perate   the   wiper   stalk   again   to   park   the  
w

iper   blades.
Load reduction modeSystem which manages the use of certain functions   according   to   the   level   of   charge  
r

emaining   in   the   battery.
When
  the   vehicle   is   being   driven,   the   load  
r

eduction   function   temporarily   deactivates  
c

ertain   functions,   such   as   the   air   conditioning,  
t

he   heated   rear   screen...
The deactivated functions are reactivated
automatically
  as   soon   as   conditions   permit.
Practical information

247
DS3_en_Chap11_verifications_ed01-2014
bonnetProtects the components of the engine and provides access for checking levels.
Opening
F Open  the   front   left   door.
F P ull the interior release lever A , located at
the
  bottom   of   the   door   aperture.F
 P ush   the   exterior   safety   catch   B to the left
and
  raise   the   bonnet.
Before
 
doing
 
anything
 
under
 
the
 
b

onnet, switch off the Stop & Start
system
 
to
 
avoid
 
any
 
risk
 
of
 
injury
 
r

esulting
 
from
 
an
 
automatic
 
change
 
to
 
S

TART
 
mode.
The location of the interior release lever
prevents  opening   of   the   bonnet   while  
t

he   front   left   door   is   closed.
checks