187
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
When the ignition is on, the lighting of this warning lamp,
a
ccompanied by an audible signal
a
nd a message in the multifunction
s
creen, indicates a gearbox
m
alfunction.
Operating fault
You risk damaging the gearbox:
- i f you press the accelerator and
brake
pedals at the same time,
-
i
f
y
ou
f
orce
t
he
l
ever
f
rom
p
osition P
to another position when the
battery
is flat.
To
reduce fuel consumption when
s
tationary for long periods with the
e
ngine running (traffic jam...), position
t
he gear lever at N and apply the
parking
brake, unless it is programmed
i
n automatic mode.
In
this
case,
the
gearbox
switches
to
back-up
m
ode
and
is
locked
in
3rd
gear.
You
may
feel
a
substantial
knock
when
changing
from
P
to R
and
from
N to R .
This
will
not
cause
any
d
amage
to
the
gearbox.
Do
not
exceed
60
mph
(100
km/h),
local
speed
r
estrictions
p
ermitting.
Have
it
checked
by
a
CITROËN
dealer
or
a
q
ualified
w
orkshop.
This
warning
lamp
may
also
come
on
if
a
door
i
s
ope
ned.
9
Driving
188
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Hill start assist
On an ascending slope, with the vehicle
stationar y, the vehicle is held for a brief
moment when you release the brake pedal:
-
i
f you are in first gear or neutral with a
m
anual
g
earbox,
-
i
f you are in position A or M with an
electronic
ge
arbox,
-
i
f you are in position D or M with an
automatic
gearbox.
Operation
On a descending slope, with the vehicle
stationary and reverse gear engaged, the
vehicle is held for a brief moment when you
release the brake pedal.
Operating fault
If a fault occurs with the system, these warning lamps come on. Contact a CITROËN dealer
o
r a qualified workshop to have the system
c
hecked.
System
which
keeps
your
vehicle
immobilised
t
emporarily
(approximately
2
seconds)
when
s
tarting
on
a
gradient,
the
time
it
takes
to
m
ove
your
foot
from
the
brake
pedal
to
the
a
ccelerator
ped
al.
This
function
is
only
active
when:
-
t
he
vehicle
is
completely
stationary,
with
y
our
foot
on
the
brake
pedal,
-
w
hen
certain
conditions
of
gradient
are
m
et,
-
w
ith
the
driver’s
door
closed.
The hill start assist function cannot be
deactivated.
Do
not
leave
the
vehicle
while
it
is
being
h
eld
in
the
hill
start
assist
phase.
If you need to leave the vehicle while
the
engine
is
running,
apply
the
parking
b
rake
manually
then
ensure
that
the
p
arking
brake
warning
lamp
is
on
(not
f
lashing)
in
the
instrument
panel.
driving
192
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Stop & Start
Operation
Going into engine STOP mode
The "ECO" warning lamp comes on i
n the instrument panel and the engine g
oes into standby automatically:
-
w
ith a manual gearbox , at speeds below
12
m
ph
(
20
k
m/h),
o
r
v
ehicle
s
tationary
w
ith
P
ureTech 130 petrol and BlueHDi Diesel
v
ersions, when you put the gear lever into
n
eutral and release the clutch pedal,
If your vehicle is fitted with the
system,
a time counter calculates
t
he sum of the periods in STOP
m
ode during a journey. It resets
i
tself to zero every time the
i
gnition is switched on with the
k
ey or the "START/STOP" button.
-
w
ith an electronic gearbox , at a speed
below
5 mph (8 km/h), when you press
t
he
brake pedal or put the gear lever into
p
osition N .
Special cases: STOP mode
unavailable
STOP mode is not invoked when:
- t he vehicle is on a steep slope (up or
d
ow n),
-
t
he driver's door is open,
-
t
he driver's seat belt is not fastened,
-
t
he vehicle has not exceeded 6 mph
(
10 km/h) since the last engine start (using
t
he key or the " START/STOP" button),
-
t
he electric parking brake is applied or
be
ing
a
pplied,
-
t
he engine is needed to maintain a
c
omfortable temperature in the passenger
c
ompartment,
-
d
emisting is active,
-
s
ome special conditions (battery charge,
e
ngine temperature, braking assistance,
a
mbient temperature...) where the engine is
n
eeded to assure control of a system.
In this case, the "ECO"
warning lamp
f
lashes for a few seconds, then
goes
off.
This operation is perfectly normal.
The
Stop
&
Start system
puts
the
engine
temporarily
into
standby
-
STOP
mode
-
during
stops
in
the
traffic (red lights, traffic jams, or other...).
The
engine
restarts
automatically
-
START
mode
-
as
soon
as
you
want
to
move
off.
The
restart
takes
place instantly, quickly and silently.
Per fect
for
urban
use,
the
Stop
&
Start
system
reduces
fuel
consumption
and
exhaust
emissions
as
well
as the noise level when stationary.
Never
refuel
with
the
engine
in
STOP
m
ode;
you
must
switch
off
the
ignition
w
ith
the
key
or
the
"START/STOP"
b
utton.
With
an
electronic
gearbox,
for
your
c
omfort
during
parking
manoeuvres,
S
TOP
mode
is
not
available
for
a
few
s
econds
after
coming
out
of
reverse
g
e a r.
STOP
mode
does
not
affect
the
f
unctionality of the vehicle, such as
braking,
power
steering,
for
example.
driving
193
C4-2_en_Chap09_conduite_ed01-2015
C4-2_en_Chap09_conduite_ed01-2015
Deactivation
Going into engine START mode
At any time, press the "ECO OFF" switch to
d eactivate the system.
This
is confirmed by the switch warning lamp
c
oming on accompanied by the display of a
m
essage.
Special cases: START invoked
automatically
The "ECO" warning lamp goes off a
nd the engine starts automatically:
-
w
ith a manual gearbox , when you fully
depress the clutch pedal,
-
w
ith an electronic gearbox :
●
g
ear lever in position A or M, when you
release
the brake pedal,
●
o
r
gear lever in position N and the brake
p
edal released, when you move the gear
l
ever to position A or M ,
●
o
r
when you engage reverse gear.For
safety reasons or to ensure smooth o
peration, START mode is invoked
a
utomatically
w
hen:
-
y
ou open the driver's door,
-
y
ou unfasten the driver's seat belt,
-
t
he speed of the vehicle exceeds 15 mph
(
25 km/h) with a manual gearbox (3 km/h
(
2 mph) with PureTech 130 petrol and
B
lueHDi Diesel versions) or 7 mph
(
11 km/h) with an electronic gearbox,
-
t
he electric parking brake is being applied,
-
s
ome special conditions (battery charge,
e
ngine temperature, braking assistance,
a
mbient temperature...) where the engine is
n
eeded to assure control of a system.
In this case the "ECO"
warning lamp
f
lashes for few seconds, then
goes
off.
This operation is perfectly normal.
With
a manual gearbox in STOP mode,
i
f
a
gear is engaged without fully
d
epressing the clutch pedal, a warning
l
amp comes on or an alert message
i
s
displayed asking you to depress the
c
lutch pedal to restart the engine. If
the system has been deactivated
i
n STOP mode, the engine restarts
i
mmediately.
9
Driving
220
C4-2_en_Chap10_verification_ed01-2015
C4-2_en_Chap10_verification_ed01-2015
Automatic
gearbox
The gearbox does not require any maintenance (no oil change).
Refer
to the manufacturer's
s
ervice schedule for details of
the
level checking interval for this
c
omponent.
Electric parking
brake
This system does not require any routine servicing. However, in
t
he event of a problem, have the
s
ystem checked by a CITROËN
d
ealer or a qualified workshop.
Manual parking
brake
If a loss of effectiveness of this
system
i s n oticed, t he p arking b rake
m
ust be checked, even between
t
wo services.
Brake pads
Brake wear depends on the style of driving, particularly in the case
o
f vehicles used in town, over short
distances.
It may be necessary to
Brake disc
wear
For information on checking brake disc wear, contact a CITRoËn
dealer
or a qualified workshop.For
more information, refer to the "Electric
p
arking brake - Operating faults" section.
Manual gearbox
The gearbox does not require any m
aintenance (no oil change).
Refer
to the manufacturer's service
s
chedule for the checking interval
f
or this component.
Electronic gearbox
The gearbox does not require any maintenance (no oil change).
Refer
to the manufacturer's service
s
chedule for details of the checking
i
nterval for this component. Only
use products recommended by
C
ITROËN or products of equivalent
q
uality
an
d
sp
ecification.
In
order to optimise the operation of
u
nits as important as those in the
b
raking system, CITROËN selects and
o
ffers very specific products.
After
washing the vehicle, dampness,
o
r in wintry conditions, ice can form
o
n the brake discs and pads: braking
e
fficiency may be reduced. Make light
b
rake applications to dry and defrost
t
he brakes.
have
the condition of the brakes checked, even
b
etween
v
ehicle
s
ervices.
Unless there is a leak in the circuit, a drop in
t
he brake fluid level indicates that the brake
p
ads are worn.
Checking this system must be done by a
C
ITROËN dealer or a qualified workshop.
Checks
235
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
For BlueHDi Diesel versions
If your vehicle has an electric parking brake,
the jack is stowed in a bag placed in the bottom
o
f the boot. If your vehicle has a manual parking brake
,
the jack is stowed under the spare wheel and
u
nder the storage box:
F
r
emove the spare wheel,
F
r
emove the polystyrene storage box,
F
p
ush the jack for ward, then lift it by its rear
par
t.The spare wheel is installed in the boot under
the
floor.
Depending
on version, the spare wheel may be
a
standard
size
steel
or
alloy
wheel,
or
for
some
c
ountries it is the "space saver" type.
For access to the spare wheel, refer to the
paragraph
"Access to the tools" on the previous
pag
e.
Access to the spare wheel
If your vehicle has an electric parking brake, only a "space saver" type of
w
heel can be stowed in the boot.
11
Practical information
237
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Removing a wheel
* position R for an electronic gearbox; P for an
automatic gearbox.
List of operations
F Remove the chromed bolt cover from each o
f the bolts using the tool 3 (according to
e
quipment).
F
F
it the security socket 4 on the
wheelbrace
1 to slacken the security bolt.
F
S
lacken the other bolts using the
w
heelbrace 1
o
n l y.
Parking the vehicle
Immobilise the vehicle where it does not block traffic: the ground must be level,
s
table and non-slippery ground.
Apply
the parking brake unless it has
b
een programmed to automatic mode,
s
witch off the ignition and engage first
g
ear* to lock the wheels.
Check
that the braking warning lamps
i
n the instrument panel are on (not
f
lashing).
The
occupants must get out of the
v
ehicle and wait where they are safe.
If
necessary, place a chock under the
w
heel diagonally opposite the wheel to
be c
hanged.
Never
go underneath a vehicle raised
u
sing a jack; use an axle stand.
11
Practical information
241
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Snow chains
In wintry conditions, snow chains improve traction as well as the behaviour of the vehicle when braking.
Advice on installation
F If you have to fit the chains during a j
ourney, stop the vehicle on a flat sur face
o
n the side of the road.
F
A
pply the parking brake and position any
w
heel chocks to prevent movement of your
v
ehicle.
F
F
it the chains following the instructions
p
rovided by the manufacturer.
F
M
ove off gently and drive for a few
m
oments, without exceeding 30 mph
(
50 km/h).
F
S
top your vehicle and check that the snow
c
hains are correctly tightened.
Use
only
the
chains
designed
to
be
fitted
to
the
t
ype
of
wheel
fitted
to
your
vehicle:
Original
tyre
size Maximum
link
size.
195/65
R15 9
mm
205/55
R16
225/45
R17
225/40
R18
cannot be fitted with chains
For more information on snow chains, contact a C ITROËN dealer or a qualified workshop.
It
is strongly recommended that before
y
ou leave, you practise fitting the snow
c
hains on a level and dry sur face.
The
snow
chains
must
be
fitted
only
t
o
the
front
wheels.
They
must
never
b
e fitted to "space-saver" type spare
wheels.
Take account of the legislation in force
i
n your country on the use of snow
chains
and the maximum running speed
a
uthorised. Avoid
driving with snow chains on roads
t
hat have been cleared of snow, to
avoid
damaging your vehicle's tyres and
t
he road sur face. If your vehicle is fitted
w
ith alloy wheels, check that no part of
t
he chain or its fixings is in contact with
t
he wheel rim.
11
Practical information