2015 Citroen C4 boot

115
C4-2_en_Chap05_amenagement_ed01-2015
C4-2_en_Chap05_amenagement_ed01-2015
F To  connect   a   12   V   accessory   (max   power:  1
20   W),   remove   the   cap   and   connect   an  
a

ppropriate
 a
daptor.
F
 
T
urn   the   key   to   the   ignition   on   position.
12 V accessory socket
This is a removable lamp, fitted in the boot wall,   which   can   be   used   to   light   the   boot   or   as  
a

  torch.
For
  the   boot   lamp   function,   refer   to   the  
"

Visibility   -   Boot   lamp"   section.
To r c h
Operation
This torch operates with ni MH type
rechargeable b atteries.
It
  has   a   battery   life   of   approximately   45   minutes  
a

nd   charges   while   you   are   driving.
Observe
  the   polarities   when   fitting   the
 r

echargeable
 b
atteries.
Never
 r

eplace
 t
he
 r
echargeable
 b
atteries
 w

ith   normal   disposable   batteries.
5
Fittings

116
C4-2_en_Chap05_amenagement_ed01-2015
C4-2_en_Chap05_amenagement_ed01-2015
F Raise the boot carpet for access to the storage   box.
This
  has   areas   for   the   storage   of   a   box   of   spare  
b

ulbs,   a   first   aid   kit,   two   warning   triangles...
It
  also   contains   the   vehicle   tools,   the   temporary  
p

uncture   repair   kit...
Storage box
Use
F Extract  the   torch   from   its   location   pulling   it  up
wards.
F
 
P
ress   the   switch,   located   on   the   back,   to  
s

witch   the   torch   on   or   off.
F
 
U
nfold   the   support,   located   on   the   back,   to  
s

et   down   and   raise   the   torch;   for   example,  
w

hen   changing   a   wheel.
Storing
F Put  the   torch   back   in   place   in   its   location  s
tarting   with   the   lower   part.
 I

f   you   have   forgotten   to   switch   off   the   torch,  
t

his   switches   it   off   automatically.
If
  the   torch   is   not   engaged   correctly,   it  
m

ay   not   charge   and   may   not   come   on  
w

hen   the   boot   is   opened.
Fittings

134
C4-2_en_Chap06_visibilite_ed01-2015
C4-2_en_Chap06_visibilite_ed01-2015
Interior mood lighting
Switching on
At night, two interior mood lamps in the front c
ourtesy   lamp   come   on   automatically   when   the  
s

idelamps   are   switched   on.
Switching off
The interior mood lighting switches off automatically   when   the   sidelamps   are  
switched
  off.
It
  can   be   switched   off   manually   by   adjusting   the  
i

nstrument   panel   lighting   rheostat   button   to   one  
o

f   the   lowest   settings. This
  comes   on   automatically   when   the   boot   is  
o

pened   and   goes   off   automatically   when   the  
b

oot   is   closed.
Boot lamp
The lighting time varies according to the circumstances:
-
 
w
hen   the   ignition   is   off,   approximately
 t

en
 m
inutes,
-
 
i
n   energy   economy   mode,
 a

pproximately   thirty   seconds,
-
 
w
hen   the   engine   is   running,   no   limit.
The
 
dimmed
 
passenger
 
compartment
 
lighting
 
improves
 
visibility
 
in
 
the
 
vehicle
 
when
 
the
 
light
 
is
 
p

o o r.
Visibility

221
C4-2_en_Chap10_verification_ed01-2015
C4-2_en_Chap10_verification_ed01-2015
adblue® additive and SCR system
f
or
 
BlueHDi   Diesel   engines
To assure respect for the environment and c
onformity   with   the   new   Euro   6   emissions  
s

tandard,   without   adversely   affecting   the  
p

er formance   or   fuel   consumption   of   Diesel  
e

ngines,   CITROËN   has   taken   the   decision   to  
e

quip   its   vehicles   with   an   effective   system   that  
a

ssociates   SCR   (Selective   Catalytic   Reduction)  
w

ith   a   particle   filter   (FAP)   for   the   treatment   of  
e

xhaust   gases.
Presentation of the SCR system
Using an additive called AdBlue® containing urea, a
 
catalytic
 
converter
 
turns
 
up
 
to
 
85%   of   nitrous o

xides
 
(NOx)
 
into
 
nitrogen
 
and
 
water,   which   are
 h

armless
 
to
 
health
 
and
 
the
 
environment.
The adblue® additive is held in a special
tank
 
located
  under   the   boot   at   the   rear   of  
t

he
 
vehicle.
 
It   has   a   capacity   of   17   litres:   this  
p

rovides
 
a
 
driving   range   of   about   12   500   miles  
(

20
 
000
 
km),
  after   which   an   alert   is   triggered  
w

arning
 
you
 
when   the   reserve   remaining   is  
e

nough
 
for
 
just   1   500   miles   (2   400   km).
During
 
each
  scheduled   service   of   your   vehicle  
b

y
 
a
 
CITROËN   dealer   or   a   qualified   workshop,  
t

he
a
d
blu

e
® additive tank is refilled in order to a
llow
 
normal   operation   of   the   SCR   system.
If
 
the
 
estimated   mileage   between   two   services  
i

s
 
greater
 
than   12   500   miles   (20   000   km),   we  
r

ecommend
  that   you   go   to   a   CITROËN   dealer  
o

r
 
a
 
qualified   workshop   to   have   the   necessary  
t

op-up
 
carried   out.
on
ce the a
dbl
ue
® tank is empty, a s
ystem
 
required
 
by   regulations   prevents  
s

tarting
 
of
 
the
 
engine.
If the SCR

is faulty, the level of
emissions
 
from
 
your   vehicle   will   no  
l

onger
 
meet
 
the
 
Euro   6   standard:   you  
v

ehicle
 
becomes
 
polluting.
In
 
the
 
event
 
of
 
a
 
confirmed   fault  
w

ith
 
the
 
SCR
 
system,   you   must   go  
t

o
 
a
 
CITROËN
 
dealer   or   a   qualified  
w

orkshop
 
as
 
soon   as   possible:   after  
a

 
running
 
distance   of   650   miles  
(

1 100
 
km),
 
a
 
system   will   be   triggered  
a

utomatically
 
to
 
prevent   engine   starting.
10
Checks

227
C4-2_en_Chap10_verification_ed01-2015
C4-2_en_Chap10_verification_ed01-2015
Recommendations on storage Procedure
F Switch  off   the   ignition   and   remove   the  k
ey,   or   if   your   vehicle   has   one,   press   the  
S

TART/STOP   button   to   switch   off   the  
e

ngine. F

R
aise the boot floor for access to the
a

d
blu
e
® tank. S
ecure
 
the   boot   floor   by   attaching   its   cord  
t

o
 
the
 
hook   on   the   parcel   shelf   support.
F
 
U

nclip
 
the   black   plastic   blanking   plug   using  
i

ts
 
tab.
F
 
I

nsert
 
your   fingers   into   the   aperture   and  
t

urn
 
the
 
blue   cap   a   6
th of a turn anti-
clockwise.
F
 
C

arefully
 
lift
 
off
 
the
 
cap,   without   dropping   it.
ne

ver store bottles of
a
dbl

ue
® in your
vehicle. Before
  topping-up,   ensure   that   the   vehicle   is  
p

arked   on   a   flat   and   level   sur face.
In wintry conditions, ensure that the
temperature   of   the   vehicle   is   above   -11°C.  
O

ther wise,   by   freezing,   the   AdBlue
® cannot
be
 
poured
 
into
 
its
 
tank.
 
Park
 
your
 
vehicle   in   a  
w

armer
 
area
 
for
 
a
 
few
 
hours
 
to
 
allow   the   top-up  
t

o
 
be
 
carried
 
out.
a

d
blu

e
® freezes at about -11°C and d
eteriorates   above   25°C.   It   is   recommended  
t

hat bottles be stored in a cool area and
protected
  from   direct   sunlight.
Under
 
these   conditions,   the   additive   can   be  
k

ept
 
for
 
at   least   a   year.
If the additive has frozen, can be used once it
has
 
completely   thawed   out.
10
Checks

228
C4-2_en_Chap10_verification_ed01-2015
C4-2_en_Chap10_verification_ed01-2015
F obtain a bottle of adbl ue®. After first c
hecking
 
the
 
use-by
 
date,
  read   carefully  
t

he instructions on use on the label before
pouring
 
the
 
contents
 
of
 
the   bottle   into   your  
v

ehicle's
 Ad

Blue
® tank. F  
A
fter   emptying   the   bottle,   wipe   away   any  
s

pillage   around   the   tank   filler   using   a   damp  
c

loth.
F  
R
efit   the   blue   cap   to   the   tank   and   turn   it  
a
  6
th of a turn clockwise, to its stop.
F
 R
efit   the   black   plastic   blanking   plug,  
c

lipping   it   in   on   the   flap
F
 
D

etach   the   cord   from   the   parcel   shelf  
s

upport   and   lower   the   boot   floor.
Important:
 
if
 
your
 
vehicle's
 
AdBlue®
tank
 
is
 
completely
 
empty
 
-
 
which
 
is
 
c

onfirmed
 
by
 
the
 
alert
 
displays
 
and
  the  
i

mpossibility
 
of
 
starting
 
the
 
engine
 
-  
you
 
must
 
add
 
at
 
least
 
3.8 litres
 

(so
 
two
 
1.89
 
litre
 
bottles). If any additive is split or splashed, wash
immediately
 
w
ith  
c
old  
w
ater  
o
r  
w
ipe  
w
ith  
a

  damp   cloth.
If the additive has crystallised, clean it
off   using   a   sponge   and   hot   water.Important:
 i
n the event of a top-up
after a breakdown because of a lack
of additive ,   you   must   wait   around  
5   minutes   before   switching   on   the  
ig

nition,
 w
ithout opening the
driver's door, locking the vehicle,
introducing the key into the ignition
switch, or introducing the key of the
"Keyless Entr y and Star ting" system
into the passenger compartment .
Switch   on   the   ignition,   then,   after  
10   seconds,   start   the   engine.
ne

ver dispose of a
dbl
ue
® additive
bottles
 
in
 
the
 
household
 
waste.   Place  
t

hem
 
in
 
a
 
special
 
container   provided  
t

his
 p

urpose
 o

r
 t

ake
 t

hem
 t
o
 y
our
 d
ealer.
Checks

234
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
Changing a wheel
Access to the tools
The tools are installed in the boot under the
f l o o r.
To  gain   access   to   them:
F

o
pen the boot,
F

r
aise the floor,
F
 
s
ecure   it   by   hooking   its   cord   on   the   hook  
o

n the rear shelf support,
F

w
ith a standard size spare wheel, unclip
and
  remove   the   box   in   the   middle   of   the  
w

heel   containing   the   tools,


or
F
 
w
ith   a   "space-saver"   spare   wheel;   lift   the  
w

heel at the rear towards you for access to
the
  storage   box   containing   the   tools.
List of tools
All of these tools are specific to your vehicle. Do   not   use   them   for   other   purposes.
1.
 W

heelbrace.
 F

or   removing   the   wheel   trim   and   the   wheel  
f

ixing
 bol
ts.
2.
 J

ack   with   integral   handle.
 F

or   raising   the   vehicle.
3.
 B

olt   cover   removal   tool.
 F

or   removing   the   bolt   head   protectors   on  
a

lloy   wheels.
4.
 S

ocket   for   the   security   bolts   (located   in   the  
g

love   box).
 F

or   adapting   the   wheelbrace   to   the   special  
"s

ecurity"
 b
olts.
5.
 C

hock   (with   ETG6   electronic   gearbox  
v

e r s i o n).
Wheel with trim
When removing the wheel ,   detach   the   trim   first   using   the   wheelbrace   1   pulling   at   the   valve  p
assage   hole.
When refitting the wheel ,
  refit   the   trim   starting   by   placing   its   notch   facing   the   valve   and  
p

ress   around   its   edge   with   the   palm   of   your   hand.
Procedure
 
for
 
changing
 
a
 
faulty
 
wheel
 
for
 
the
 
spare
 
wheel
  using   the   tools   provided   with   the   vehicle.
Practical information

235
C4-2_en_Chap11_info-pratique_ed01-2015
C4-2_en_Chap11_info-pratique_ed01-2015
For BlueHDi Diesel versions
If your vehicle has an electric parking brake,
the   jack   is   stowed   in   a   bag   placed   in   the   bottom  
o

f   the   boot. If your vehicle has a manual parking brake
,
the   jack   is   stowed   under   the   spare   wheel   and  
u

nder   the   storage   box:
F
 
r
emove   the   spare   wheel,
F
 
r
emove   the   polystyrene   storage   box,
F
 
p
ush   the   jack   for ward,   then   lift   it   by   its   rear  
par

t.The spare wheel is installed in the boot under
the
  floor.
Depending
  on   version,   the   spare   wheel   may   be  
a 

standard
 
size
 
steel
 
or
 
alloy
 
wheel,
 
or
 
for
 
some
 c

ountries   it   is   the   "space   saver"   type.
For access to the spare wheel, refer to the
paragraph
  "Access   to   the   tools"   on   the   previous  
pag

e.
Access to the spare wheel
If your vehicle has an electric parking brake,   only   a   "space   saver"   type   of  
w

heel   can   be   stowed   in   the   boot.
11
Practical information