2015 Citroen C ZERO wheel bolts

101
C-zero_en_Chap08_info-pratiques_ed01-2014
Changing a wheel
Tools required
- A jack: for lifting the vehicle.
- A wh eelbrace: for removing and refitting
the wheel bolts.
-
A ha

ndle: for operating the jack.
These tools are not supplied with your vehicle.Parking the vehicle
Immobilise the vehicle where it does not
block traffic: the ground must be level,
stable and not slippery.
Apply the parking brake, switch off the
ignition and put the drive selector in
position P to lock the wheels.
If necessary, place a chock under the
wheel diagonally opposite the wheel to
be changed.
You must ensure that the occupants get
out of the vehicle and wait where they
are safe.
Never go underneath a vehicle raised
using a jack; use an axle stand.
Wheel with wheel trim
When removing the wheel , first
remove the wheel trim using the
wheelbrace, by pulling at the valve hole.
When fitting the wheel , refit the wheel
trim starting by aligning the valve hole
with the valve, and then press on the
edge of the trim with the palm of your
hand.
8
Practical information

102
C-zero_en_Chap08_info-pratiques_ed01-2014
F Extend the jack until its head comes into contact with the jacking point A or B used. The
vehicle's contact sur face A or B must be engaged with the central part of the head of the jack.
F
Ra

ise the vehicle until there is sufficient space between the wheel and the ground.
F Sl
acken the bolts using the wheelbrace.
F Po
sition the foot of the jack on the ground
and ensure that it is directly below the
front
A

or rear B jacking point provided on
the underbody, whichever is closest to the
wheel to be changed.
Removing a wheel
Practical information

103
C-zero_en_Chap08_info-pratiques_ed01-2014
F Remove the bolts and store them in a clean
place.
F
Re

move the wheel. Ensure that the jack is stable. If the
ground is slippery or loose, the jack
might slip or drop - Risk of injury!
Take care to position the jack only at
one of the vehicle’s jacking points A
or B under the vehicle, ensuring that the
contact sur face of the vehicle’s jacking
point is centred on the head of the jack.
Other wise there is a risk of damage to
the vehicle and/or that the jack might
drop - Risk of injury!
8
Practical information

104
C-zero_en_Chap08_info-pratiques_ed01-2014
Fitting a wheel
F Put the wheel in place on the hub.
F Sc rew in the bolts by hand.
F
Pr

e-tighten the bolts using the wheelbrace. F Lo
wer the vehicle fully.
F Fo ld the jack and detach it.F Ti
ghten the bolts using the wheelbrace.
After changing a wheel
Have the tightness of the bolts and the
tyre pressure of the new wheel checked
by a CITROËN dealer or a qualified
workshop without delay.
Practical information

120
C-zero_en_Chap08_info-pratiques_ed01-2014
accessories
A wide range of accessories and genuine parts is available from the CITROËN dealer network.
These accessories and parts are all suitable for your vehicle and benefit from CITROËN's
recommendation and warranty.
Conversion kits
You can obtain an "Enterprise" kit to convert a
trade vehicle to a private car and vice-versa.
"Comfort":
black armrest, reading lamp, insulated
modules, rear parking sensors, cigarette
lighter, ashtray with base, head restraint
mounted coat hanger...
"Transport solutions":
boot liner, boot carpet, rear parcel shelf, boot
dividers...
"Security and safety":
alarm, wheel security bolts, child seats,
breathalyzer, warning triangle, high visibility
vest, first aid kit, snow chains, non-slip covers,
pet transport cage, pet safety belt...
Precautions for
washing
To avoid damaging the electrical
components, the use of a high pressure
jet wash is strictly prohibited:
-
in t
he front compartment (under the
bonnet),
-
un

der the body.
For washing the body, do not use a
pressure greater than 80
b

ars.
Check - before washing the vehicle -
that the charging flaps and the charging
socket covers (normal and fast charge)
are properly closed.
do no

t wash the vehicle while the
battery is being recharged.
Practical information