2015 Citroen BERLINGO MULTISPACE RHD lock

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
155
recommendations on storage
a
dBlue® freezes at about -11°C and
 
deteriorates   above   25°C.   It   is  
recommended

  that   bottles   be   stored   in  
a

 
cool
 
area   and   protected   from   direct  
sunlight.
Under these conditions, the additive
can

 
be
 
kept   for   at   least   a   year.
If the additive has frozen, can be used
once
 
it
 
has   completely   thawed   out.
n

ever store bottles of
a
dBlue
® in
your
 
vehicle. Procedure
Before topping-up, ensure that the
vehicle
  is   parked   on   a   flat   and   level  
surface.
In wintry conditions, ensure that
the

  temperature   of   the   vehicle   is  
above -1

1°C.   Otherwise,   by   freezing,  
the

a dBlue
® cannot be poured into its
tank.
 
Park
 
your   vehicle   in   a   warmer  
area for a few hours to allow the top-up
to

 
be
 
carried   out.
F
 
Switch

 
off   the   ignition   and   remove  
the

 
key. -

For access to the a
dBlue
® tank, open
 
the
 
filler
 
flap;
 
the
 AdBlue® filler cap is located to the left of the fuel
filler
 
cap
-
 
T

urn
 
the
 
blue
 
cap
 
a
 
6
th of a turn
anti-clockwise.
-
 
Lift

 
off
 
the
 
blue
 
cap.
adBlue® additive
CHECkS
7

Berlingo_2_VP_en_Chap07_Verification_ed02-2014
156
- obtain a bottle of adBlue®. After first
 
checking
 
the
 
use-by
 
date,  
read carefully the instructions on
use on the label before pouring
the contents of the bottle into your
vehicle's

a
dBlue
® tank.
Important
:
 
if
 
your   vehicle's
 
a

dBlue
® tank is completely 
empty
 
-
 
which   is   confirmed   by   the alert

 
messages   and   the   impossibility
 of

 
starting
 
the   engine,   you   must   add   at
 least

 
3.8
 
litres   (so   two   1.89   litre bottles). -
 
After
  emptying   the   bottle,   wipe  
away

  any   spillage   around   the   tank  
filler

  using   a   damp   cloth.
If any additive is split or splashed,
wash   immediately   with   cold   water  
or

  wipe   with   a   damp   cloth.
If the additive has crystallised, clean it
off   using   a   sponge   and   hot   water.
-  
Refit
  the   blue   cap   to   the   tank   and  
turn

  it   a   6
th of a turn clockwise, to its stop.
-
 
Close

 
the
 
filler   flap.
n
ever dispose of
a
dBlue
® additive
bottles
 
in
 
the
 
household
 
waste.  
Place

 
them
 
in
 
a
 
special
 
container  
provided

 
this
 
purpose
 
or
 
take
 
them   to  
your

 
dealer.
Important:
 
in the event of a top-
up after a breakdown because
of a lack of additive, signalled
by
 
the
 
message
 
"Top
 
up
 
emissions  
additive:

 
Starting
 
prevented",
 
you   must  
wait

 
around
 
5
 
minutes
 
before
 
switching  
on the ignition,

without opening the
driver's door, locking the vehicle or
introducing the key into the ignition
switch.
Switch on the ignition, then, after
10
 
seconds,
 
start
 
the
 
engine.
adBlue® additive

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
168
cHAnGInG A BuLB
type A
All   glass   bulb:   pull   gently  
as

  it   is   fitted   by   pressure.
High pressure washing
Open the bonnet. T o   access   the   bulbs,  reach
  behind   the   headlamp   unit.
Carry out the operations in reverse
order
  to   refit   each   bulb   and   check   that  
the

  bonnet   is   closed   securely.type c
Halogen

  bulb:   release   the  
retaining

  spring   from   its  
housing.
type B
Bayonet
  bulb:   press  
on the bulb then turn it
anticlockwise.
Halogen
  bulbs   must   be   changed  with
  the   headlamp   off.   Wait   a   few  
minutes

  (risk   of   serious   burns).  
d
o not touch the bulb directly with your
fingers,
  use   lint-free   cloths.
It
  is   normal   for   condensation   to   form  
inside

  the   headlamps.   Regular   use   of  
the

  vehicle   eliminates   this   misting.The
  bulbs   must   be   changed   with  
the ignition of

f or with the battery
disconnected.   Wait   approximately  
3 minutes

  after   changing   the   bulb  
before

  reconnecting   the   battery.
Check   that   the   lamps   operate   correctly  
after

  each   operation.
When using this type of washing
on stubborn dirt, do not persist on
the   headlamps,   the   lamps   and   their  
edges

  to   avoid   damaging   their   coating  
and

  seals.
types of bulb
Various types of bulb are fitted to your vehicle.
 T o   remove   them:
type

d
Light

  emitting   diode  
(LED):

  for   replacement  
of

  the   daytime   running  
lamps,

  contact   a  
CITR

o Ë n dealer or a
qualified
  workshop.
Changing a bulb

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
169
3. d irection indicators
type B

,   PY21W   -   21W   (amber)
-
 
Remove
  the   cover   by   pulling   the  
flexible

  rubber   tab.
-
 
T
urn   the   bulb   holder   a   quarter  
turn

  anticlockwise.
-
 
Remove
  the   bulb   by   pressing  
it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure
correct

  sealing.
2.
Sidelamps


type A

, W5W - 5W
-
 
Remove

 
the
 
cover
 
by
 
pulling
 
the
 
flexible

 
rubber
 
tab.
-
 
Remove

 
the
 
bulb
 
holder
 
fitted
 
by
 
pressure

 
by

 
pullin

g
 
the

 
connector

.
-
 
Change

 
the
 
bulb.
-
 
Ensure

 
that
 
the
 
cover
 
is
 
refitted
 
correctly all round to assure
correct

 
sealing.
FrOnt LAMPS
1. d ipped / Main beam headlamps
type

c , H4 - 55W
-
 
Remove
  the   centre   cover   by  
pullin

g   the   flexible   rubber   tab.
-
d isconnect the electrical
connector.
-
 
Release
  the   retaining   tab.
-
 
Change
  the   bulb   taking   care  
to

  align   the   metal   part   with   the  
grooves

  on   the   lamp.
-
 
Reposition
  the   retaining   tab.
-
 
Ensure
  that   the   cover   is   refitted  
correctly all round to assure
correct

  sealing.
Changing a bulb
QUICk HELP
8

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
171
rEAr LAMPS
This procedure requires the use of the spanner supplied with the tools for
changing  a   wheel.
When
  refitting,   take   care   to  
reposition the tabs and the supply
wire correctly to avoid trapping


the
  wire.
a

fter changing the rear direction
indicator
  bulb,   the   reinitialisation   time  
is
  above   2   minutes.
-
Move aside the 4 tabs then extract
the
  bulb   holder.
-
 
Remove
  the   faulty   bulb   by  
pressing it lightly while turning it
anticlockwise.
-

 
Change
  the   bulb.
When
  removing   the   lamp   unit:
-
 
with
  tailgate,   pull   the   lamp   unit  
towards the centre of the vehicle,
-

 
with
  hinged   doors,   pull   the   lamp  
unit

  towards   you.
For
 
more
 
information
 
concerning
 
the
 bulbs,
 
refer
 
to
 
the
 
"Types
 
of
 
bulb".
1.

Brake lamps / sidelamps


type B

,
 
P21/5W
 
-
 
21/5W
2.
d
irection indicators
type B

,
 
PY21W
 
-
 
21W
 
(amber)
3.
r
eversing lamps
type B

, P21W - 21W
4.

Foglamps


type B

, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the
 
headlamps,
 
the
 
other
 
lamps
 
and

 
their
 
edges
 
to
 
avoid
 
damaging
 
their

 
coating
 
and
 
seals. Chapter
  9,   "Changing   a   wheel"  
section.
-


Identify the faulty bulb, then open
the

  rear   doors   to   180°.
Chapter
  3,   "Access"   section.
-
 
Remove
  the   two   fixing   bolts   using  
the

  spanner   provided.
-
 
Pull
  the   lamp   unit   from   the   outside.
-
 
Holding
  the   lamp,   disconnect   the  
electrical

  connector.
Changing a bulb
QUICk HELP
8

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
172
nuMBEr PLAtE LAMPS
- Unscrew  the   two   nuts.
-  
Push
  the   pins.
-

If necessary
, disconnect the
connector
  to   remove   the   lamp.
-
 
Change
  the   bulb.
With tailgate
-
d
isengage the plastic lens using a
screwdriver.
-
 
Change

 
the
 
bulb.
-

Replace the plastic lens and press
on

 
it.
tHIrd BrAKE LAMP
type A ,   W16W   -   16W
With hinged doors
-
 
Unclip

 
the
 
interior
 
trim.
-
d
isconnect the connector by
moving
 
aside
 
its
 
tab.
-
 
T

urn
 
the
 
bulb
 
holder
 
a
 
quarter
 
turn
 
anticlockwise.
-

 
Change

 
the
 
bulb.
-
 
Put

 
the
 
bulb
 
holder
 
back
 
in
 
place
 
and

 
reconnect
 
the
 
connector.
-
 
Put

 
the
 
trim
 
back
 
in
 
place.type A
, W5W - 5W
Changing a bulb

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
174
dASHBOArd FuSES
Tilt the cover to gain access to the
fuses.Fuses
F Amperes  Aa
llocation
1 15 Rear wiper
2 - Spare
3 5
a

irbag
4 10 Air
  conditioning,   diagnostic   socket,   mirror   control,  
headlamp

  beam
5 30 Electric windows
6 30Locks
7 5Rear
  courtesy   lamp,   front   map   reading   lamp,   roof  
console
8 20 Audio

  equipment,   screen,   tyre   under-inflation  
detection,

  alarm   and   siren
9 30Front
  and   rear   12V   socket
10 15 Central
  column
11 15 Low current ignition switch
12 15 Rain and sunshine sensor, airbag
13 5 Instrument
  panel
14 15 Parking
  sensors,   digital   air   conditioning   controls,  
hands-free

  phone   kit
15 30 Locks
16 - Spare
17 40Rear
  screen/mirrors   demist/defrost
Changing a fuse

10.55
Berlingo_2_VP_en_Chap10b_RT6-2-8_ed02-2014
FrEQuEntLY ASKE d Q u ES t IO n S
QuEStIOnA n SWE rSOL ut IO n
Some

 
characters   in   the  
media

 
information   are   not  
displayed correctly while
playing. The

  audio   system   does   not   display   some   types   of   characters.Use
  standard   characters   to   name   tracks   and  
folders.
Playing

  of   streaming   files  
does

 
not   start. The
  peripheral   device   connected   does   not   support   automatic   play. Start   the   playback   from   the   device.
The
 
names   of   tracks   and  
the

 
track   length   are   not  
displayed on the screen
when

 
streaming   audio. The
  Bluetooth   profile   does   not   allow   the   transfer   of   this   information.
The
 
quality   of   reception  
of the radio station
listened to gradually
deteriorates or the stored
stations do not function
(no

 
sound,   87.5 Mhz   is  
displayed...). The

  vehicle   is   too   far   from   the   transmitter   used   by   the   station   listened  
to

  or   there   is   no   transmitter   in   the   geographical   area   through   which   the  
vehicle

  is   travelling. Activate
  the   "RDS"   function   by   means   of   the  
short-cut

  menu   to   enable   the   system   to   check  
whether

  there   is   a   more   powerful   transmitter   in   the  
geographical

  area.
The
  environment   (hills,   buildings,   tunnels,   basement   car   parks...)   block  
reception,

  including   in   RDS   mode.This
  phenomenon   is   normal   and   does   not   indicate  
a

  fault   with   the   audio   system.
The
  aerial   is   absent   or   has   been   damaged   (for   example   when   going  
through

  a   car   wash   or   into   an   underground   car   park).Have
  the   aerial   checked   by   a   CITROËN   dealer.
I
 
cannot   find   some   radio  
stations in the list of
stations

  received. The
  station   is   not   received   or   its   name   has   changed   in   the   list.
Some
  radio   stations   send   other   information   in   place   of   their   name   (the  
title

  of   the   song   for   example).
The
  system   interprets   this   information   as   the   name   of   the   station.
The
 
name   of   the   radio  
station

  changes.