2015 Citroen BERLINGO MULTISPACE RHD sensor

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
164
FIttInG tHE WHEEL trIM
The tyre valve must be centred in the wheel
  trim   cut-out.
This
  position   is   essential   for   fitting   the  
wheel

  trim   correctly   on   the   steel   wheel.  
(If

the valve is not correctly aligned with
the
  cut-out,   the   anti-rotation   system  
will be in contact with the heads of the
wheel

  bolts   and   risks   being   damaged  
if

  the   user   persists   in   fitting   the   wheel  
trim

  in   this   incorrect   position). -

Ensure that all of the clips are
engaged except the last one
(opposite

  the   valve   hole).
-
 
Strike
  the   wheel   trim   with   the   palm  
of your hand, opposite the valve
in

  the   area   of   the   last   fixing   clip  
(always

  in   the   direction   of   clipping).
-

Ensure that the outer edge of
the

  wheel   trim   is   not   deformed   or  
pushed

  into   the   wheel.
●
 c
orrect position for the edge of
the
  wheel   trim.
●
 
Incorrect
position for the edge of
the
  wheel   trim.
6. refitting the repaired
wheel
The wheel is refitted as described in step   5,   not   forgetting   to   refit   the   wheel  
trim.
Refer

  to   the   "Instruments   and  
controls" section of chapter 3,
"T

yre   under-inflation   detection"  
part,

  for   recommendations   after  
changing

  a   wheel   fitted   with   a   tyre  
under-inflation

  detection   sensor.
Refer
  to   the   "Identification  
markings"

  section   of   chapter   9   to  
locate

  the   tyre   label.
The spare wheel is not designed
to
  be   used   over   long   distances.  
Have the tightening of the bolts
and

  the   tyre   pressure   checked   by  
a

  CITROËN   dealer   or   a   qualified  
workshop

  as   soon   as   possible.
Have the original wheel repaired
and
  refitted   by   a   CITROËN   dealer  
or

  a   qualified   workshop   as   soon   as  
possible.
Changing a wheel

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
174
dASHBOArd FuSES
Tilt the cover to gain access to the
fuses.Fuses
F Amperes  Aa
llocation
1 15 Rear wiper
2 - Spare
3 5
a

irbag
4 10 Air
  conditioning,   diagnostic   socket,   mirror   control,  
headlamp

  beam
5 30 Electric windows
6 30Locks
7 5Rear
  courtesy   lamp,   front   map   reading   lamp,   roof  
console
8 20 Audio

  equipment,   screen,   tyre   under-inflation  
detection,

  alarm   and   siren
9 30Front
  and   rear   12V   socket
10 15 Central
  column
11 15 Low current ignition switch
12 15 Rain and sunshine sensor, airbag
13 5 Instrument
  panel
14 15 Parking
  sensors,   digital   air   conditioning   controls,  
hands-free

  phone   kit
15 30 Locks
16 - Spare
17 40Rear
  screen/mirrors   demist/defrost
Changing a fuse

Berlingo_2_VP_en_Chap08_aide-rapide_ed02-2014
176
FuSES undEr tHE BOnnEt
after opening the bonnet, unclip and tilt
the corresponding box to gain access
to
  the   fuses. Fuses
F Amperes  Aa
llocation
1 20 Engine
  management
2 15 Horn
3 10 Front
  and   rear   wash-wipe   pump
4 20 Headlamp
  wash   pump
5 15 Engine
  components
6 10 Steering wheel angle sensor,
d SC
7 10Brake
  switch,   clutch   switch
8 25 Starter
9 10Headlamp
  beam   motor,   parc   management   unit
10 30 Engine
  components
11 40 Spare
12 30 Wipers
13 40 Built-in
  systems   interface
14 30 Pump
15 10 Right-hand
  main   beam   headlamp
16 10Left-hand
  main   beam   headlamp
17 15Right-hand
  dipped   beam   headlamp
18 15 Left-hand
  dipped   beam   headlamp
Changing a fuse