2015 Citroen BERLINGO MULTISPACE warning

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
51
Reactivation
Press the "ECO OFF" switch again.
The   system   is   active   again;   this   is  
confirmed

  by   the   switch   warning  
lamp

  going   off   and   a   message   in   the  
instrument

  panel.
The
  system   is   reactivated  
automatically

  at   every   new   start  
using

  the   key.
Operating fault
In the event of a malfunction with  the   system,   the   "ECO
OFF"
  switch   warning   lamp  
flashes,

  then   comes   on  
continuously

.
Maintenance
Before working under the bonnet, deactivate  the   Stop   &   Start   system  
to

  avoid   any   risk   of   injury   resulting  
from

  automatic   operation   of   START
 mode.
This

  system   requires   a   specific  
battery

  with   a   special   specification  
and

 
technology   (reference   numbers  
available

  from   a   CITROËN   dealer   or   a  
qualified

  workshop).
Fitting a battery not listed by
CITROËN introduces
  the   risk   of  
malfunction

  of   the   system.
The
  Stop   &   Start   system   makes  
use

  of   advanced   technology.  
All
 
work

  on   this   type   of   battery   must  
be done only by a CITR

o Ë n dealer or
a
 
qualified   workshop.
have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 

mode,
 
the

 
vehicle
 
may
 
stall.
 
All

 
of
 
the
 
warning
 
lamps

 
in
 
the
 
instrument
 
panel
 
come
 
on.

 
It
 
is
 
then
 
necessary
 
to
 
switch
 
off
 
the ignition and start the engine again
using

 
the
 
key.
Stop & Start
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
52
Good practice when stopping Good practice when starting
Diesel pre-heating warning
lamp
If  the   temperature   is   high  
enough,

  the   warning   lamp  
comes

  on   for   less   than  
one

second, you can start
without
  waiting.
In cold weather, wait for this warning
lamp
 
to
 
go   off   then   operate   the   starter  
(Starting position) until the engine
starts.
Door or bonnet open warning lamp
If  this   comes   on,   a   door   or   the   bonnet
 is

  not   closed   correctly,   check!
Minimise engine and gearbox wear
When switching off the ignition, let the
engine run for a few seconds to allow
the turbocharger (
d iesel engine) to
return
  to   idle.
d

o not press the accelerator when
switching
  off   the   ignition.
There is no need to engage a gear
after
  parking   the   vehicle.
STARTING AND ST OPPING
Running and accessories position.
To
  unlock   the   steering,   turn   the  
steering wheel gently while turning the
key

,   without   forcing.   In   this   position,  
certain

  accessories   can   be   used.
Starting position.
The starter is operated, the engine
turns
  over,   release   the   key.
STOP position:
  steering   lock.
The
  ignition   is   off.  
T
urn   the   steering  
wheel

  until   the   steering   locks.   Remove  
the

  key.
Starting and stopping

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
53
HILL START ASSIST
This system (also called HHC - Hill Holder
  Control),   linked   to   the   dynamic  
stability

  control   system,   makes   hill  
starts easier and is activated in the
following

  conditions:
-
 
the
  vehicle   must   be   stationary,  
engine

  running,   foot   on   the   brake,
-
 
the
  gradient   of   the   road   must   be  
steeper than 5%,
-

 
uphill,
  the   gearbox   must   be   in  
neutral or in a gear other than
reverse,
-

 
downhill,
  reverse   gear   must   be  
engaged.
The

  Hill   Start  
Assist
  system   is   a   driving  
aid.

  It   is   not   an   automatic   vehicle  
parking

  function   or   an   automatic  
parking

  brake.
Operation
With the brake pedal and clutch pedal pressed,   from   the   time   you   release  
the

  brake   pedal,   without   using   the  
parking

  brake,   you   have   approximately  
2 seconds

  to   move   off   before   the  
vehicle

  starts   to   roll   back.
During
  the   moving   off   phase,   the  
function

  is   deactivated   automatically,  
gradually

  releasing   the   braking  
pressure.

  During   this   phase,   the  
characteristic

  noise   of   mechanical  
release

  of   the   brakes   may   be   heard,  
indicating

  the   imminent   movement   of  
the

  vehicle.
Operating fault
Hill start assist is deactivated in the
following   situations:
-

when the clutch pedal is released,
-

 
when
  the   parking   brake   is   applied,
-

when the engine is switched of
f,
-
 
when
  the   engine   stalls.
If
  a   malfunction   of   the  
system

  occurs,   this  
warning

  lamp   comes   on  
accompanied

  by   an   audible  
signal

  and   confirmed   by  
a

  message   in   the   screen.   Have   the  
system

  checked   by   at   a   CITROËN  
dealer

  or   a   qualified   workshop.
Starting and stopping
REadY To Go
3

55
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
DIRECTION INDICATORS
"Motorway" function
Press  the   control   up   or   down   to   flash  
the corresponding direction indicator
three

  times.
LIGHTING
Left: downwards passing the point  of   resistance.
Right:
  upwards   passing   the  
point

  of   resistance.
Front and rear lighting
Lighting off
Automatic
  illumination   of  
headlamps
SidelampsDipped

  beam   (green)
Dipped beam/main beam change
Pull
 
the
 
stalk   fully   towards   you.
Lighting-on audible warning
o

n switching off the ignition, all of the
lamps
 
turn   off,   except   dipped   beam   if  
automatic

  guide-me-home   lighting   has  
been

 
activated.
 Checking

 
by
 
means
 
of
 
the
 
indicator
 lamps

 
in
 
the
 
instrument
 
panel
 
is
 described

 
in
 
the
 
"Instruments
 
and
 controls"

 
section
 
of
 
chapter
 
3.
Direction indicators
Selection is by turning this
ring. Main
  beam   (blue)
To activate the lighting
control, turn this ring to
the lighting off position "0"
then to the selection of
your   choice.
o

n opening the driver's door, there is
an audible warning if you have left the
lighting
  on.
Steering mounted controls
EaSE oF USE and CoMFoRT
4

56
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
LED DAYTIME RUNNING LAMPS
Rear foglamps (amber, 
2nd rotation of the ring
forwards).
Front
  foglamps   (green,   1st  
rotation

  of   the   ring   forwards).
Rotate this ring forwards
to switch on and
rearwards   to   switch   off.
Their   state   is   confirmed   by  
the

  warning   lamps   in   the  
instrument

  panel. Do   not   forget   to   switch   them   off  
when

  they   are   no   longer   needed.
Operation   of   the   automatic   illumination  
of

  headlamps   switches   off   the   rear  
foglamps,

  but   the   front   foglamps  
remain

  on.
To switch off the front and
rear   foglamps,   turn   the  
ring rearwards twice in
succession.
Automatic illumination of headlamps
In foggy weather or in snow,
the  sunshine   sensor   may   detect  
sufficient

  light.  
As
  a   consequence,  
the

 
lighting   will   not   come   on  
automatically

.
If
  necessary,   you   must   switch  
on

  the   dipped   beam   headlamps  
manually

.
d

o not cover the sunshine sensor
located on the windscreen, behind
the
 
mirror.   It   is   used   for   the   automatic  
illu

mination   of   headlamps   and   for   the  
automatic

  rain   sensitive   wipers.
Activation
Turn the ring to the AUTO
  position.  
The activation of this function is
accompanied

  by   a   message   in   the  
screen.
Deactivation
T

urn
  the   ring   forwards   or   rearwards.  
The deactivation of this function is
accompanied

  by   a   message   in   the  
screen.
The

 
function   is   deactivated   temporarily  
when

  you   use   the   manual   lighting  
control

  stalk. The
  sidelamps  
and

  dipped   beam  
headlamps

  switch  
on

  automatically   if  
the light is poor

, or
during operation of the windscreen
wipers.  
They
  switch   off   as   soon   as   the  
light

  becomes   bright   enough   or   the  
windscreen

  wipers   stop.
This
  function   is   not   compatible   with   the  
daytime

  running   lamps.
o

n starting the vehicle, in daylight the
LED
 
daytime
 
running
 
lamps
 
come
 
on
 
automatically

.
If
 
the
 
sidelamps
 
and
 
headlamps
 
are
 
switched

 
on
 
manually
 
or
 
automatically,
 
the

 
daytime
 
running
 
lamps
 
go
 
off.
Programming
For countries where exterior lighting by
day   is   not   a   legal   requirement,   you   can  
activate or deactivate the function via
the

  configuration   menu.
If the user does not operate any
equipment
 
for
 
30
 
minutes,
 
the
 
Economy

 
mode
 
engages
 
to
 
avoid
 
discharging

 
the
 
battery.
 
Electrical
 
functions are put on standby and the
battery

 
warning
 
lamp
 
flashes.
Sidelamp
 
operation
 
is
 
not
 
affected
 
by
 
Economy

 
mode.
In clear weather or in rain, both day
and  night,   rear   foglamps   dazzle   and  
their

  use   is   prohibited.
Refer to chapter 8, "Battery
section".
Front and rear foglamps
They
 
operate
 
with
 
the
 
sidelamps
 
and
 
dipped

 
beam
 
headlamps.
Steering mounted controls

 57
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
If the sunshine sensor
does not function correctly,
the  lighting   comes   on  
accompanied

  by   the   service  
warning

  lamp,   an   audible  
signal

 
and   a   message   in   the   screen.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Guide-me-home lighting
Keeping the dipped beam headlamps on   temporarily   with   the   ignition   off,  
makes

  the   driver's   exit   easier   when   the  
light

  is   poor.
HEADLAMP BEAM
The beam setting must be adjusted to suit
  the   load   in   the   vehicle.
0 -
  No   load.
1 -
  Partial   load.
2 -
 
A
verage   load.
3 -
  Maximum   authorised   load.
Manual operation
-
 With
 
the
 
ignition
 
off,
 
"flash"
 
the
 headlamps
 
within
 
one
 
minute
 
after
 
switching

 
off
 
the
 
ignition.
The
 
guide-me-home
 
lighting
 
switches
 
of

f
 
automatically
 
after
 
a
 
set
 
time.
Automatic operation
Refer to chapter 10, "Screen
menu
 
map"
 
section. Initial setting is position 0.
a

ctivate the function via the
vehicle
 
configuration
 
menu. Programming
The
 
system
 
is
 
activated
 
or
 
deactivated
 
in

 
the
 
vehicle
 
configuration
 
menu.
The
 
system
 
is
 
activated
 
by
 
default.
Switching off
The
 
system
 
does
 
not
 
operate:
-

below a certain angle of rotation of
the steering wheel,
-

 
above

 
25
 
mph
 
(40
 
km/h),
-
 
when

 
reverse
 
gear
 
is
 
engaged.
Switching on
This
 
function
 
starts:
-

when the corresponding direction
indicator is switched on,
or
-

 
from

 
a
 
certain
 
angle
 
of
 
rotation
 
of
 
the

 
steering
 
wheel.
With
 
dipped
 
or
 
main
 
beam
 
headlamps,
 
this

 
function
 
makes
 
use
 
of
 
the
 
beam
 
from

 
a
 
front
 
foglamp
 
to
 
illuminate
 
the
 
inside of a bend, when the vehicle
speed

 
is
 
below
 
25
 
mph
 
(approximately
 
40

 
km/h)
 
(urban
 
driving,
 
winding
 
road,
 
intersections,

 
parking
 
manouevres...).
Cornering lighting
Travelling abroad
If using your vehicle in a country
that drives on the other side of the
road,
  the   headlamps   must   be   adjusted  
to

 
avoid   dazzling   on-coming   drivers.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Steering mounted controls
EASE OF USE and COMFORT
4

111
Berlingo-2-VP_en_Chap05_Securite_ed01-2015
HAZARD WARNING LAMPS
H
ORN
Press the centre of the steering wheel.
PARKING BRAKE
Applying
Pull the parking brake lever up to immobilise
  your   vehicle.
Check
  that   the   parking   brake   is   applied  
firmly

  before   leaving   the   vehicle.Pull
  on   the   parking   brake   lever,   only
with the vehicle stationary.
In the exceptional case of use of the
parking
  brake   when   the   vehicle   is  
moving,

  apply   the   brake   by   pulling  
gently

  to   avoid   locking   the   rear   wheels  
(risk

  of   skidding).
Press this button, the direction
indicators
 
flash.
They
 
can
 
operate
 
with
 
the
 
ignition
 
off.
The
 
hazard
 
warning
 
lamps
 
should
 
only
 
be used in dangerous situations, when
stopping

 
in
 
an
 
emergency
 
or
 
when
 
driving

 
in
 
unusual
 
conditions.
When
  parking   on   a   slope,   direct   your  
wheels

  towards   the   pavement   and   pull  
the

  parking   brake   lever   up.
There is no advantage in engaging
a
  gear   after   parking   the   vehicle,  
particularly

  if   the   vehicle   is   loaded.
If the parking brake is still on or has not been released properly, this is
indicated
  by   this   warning   lamp   which
 comes

  on   on   the   instrument   panel.
Automatic operation of hazard
warning lamps
When braking in an emergency, depending on the force of deceleration,
the  hazard   warning   lamps   come  
on

  automatically.  
They
  switch   off  
automatically

  the   first   time   you  
accelerate.
It

  is   also   possible   to   switch   them   off   by  
pressing

  the   switch   on   the   dashboard.Releasing
Pull the lever up slightly and press the
button  to   lower   the   parking   brake   lever.
driving safely
SaFETY
5

ABS
ABS
11 5
Berlingo-2-VP_en_Chap05_Securite_ed01-2015
ANTI-LOCK BRAKING SYSTEM
(ABS / EBFD)
The ABS   and   EBFD   (electronic   brake  force
  distribution)   systems   improve   the  
stability

  and   manoeuvrability   of   your  
vehicle

  on   braking,   in   particular   on  
poor

  or   slippery   surfaces.
The
 
ABS
  prevents   locking   of   the  
wheels, the EBF

d provides control of
the
  braking   pressure   wheel   by   wheel.If
  this   warning   lamp   comes  on,
  accompanied   by   an  
audible

  signal   and   a   message  
in the screen, it indicates a
malfunction

  of   the  
ABS
  which  
could result in a loss of control of the
vehicle

  on   braking.
If
  this   warning   lamp   comes  
on,

  together   with   the   brake  
and

  STOP
 
warning   lamps,  
accompanied

  by   an   audible  
signal

  and   a   message   in   the  
screen,

  it   indicates   a   malfunction   of  
the

  electronic   brake   force   distribution  
which could result in a loss of control of
the

  vehicle   on   braking.
EMERGENCY BRAKING
ASSIST

ANCE (EBA)
In an emergency, this system enables the  optimum   braking   pressure   to   be  
reached

  more   quickly,   press   the   pedal  
firmly

  without   releasing   it.
It is triggered by the speed at which the
brake
  pedal   is   pressed   down.
This
  alters   the   resistance   of   the   brake  
pedal

  under   your   foot.
To
  maintain   operation   of   the  
emergency

  braking   assistance   system:  
keep

  your   foot   on   the   brake   pedal.
Good practice
The anti-lock braking system comes into  operation   automatically   when  
there

  is   a   risk   of   wheel   lock.   It   does   not  
reduce

  the   braking   distance.
o

n very slippery surfaces (ice,
oil, etc...)
  the  
ABS
  may   increase   the  
braking

  distance.   When   braking   in  
an

  emergency,   do   not   hesitate   to  
press

  the   brake   pedal   firmly,   without  
releasing the pressure, even on a
slippery surface, you will then be able
to

  continue   to   manoeuvre   the   vehicle  
to

  avoid   an   obstacle.
Normal
  operation   of   the  
ABS
  may   be  
felt

  by   slight   vibration   of   the   brake  
pedal.
When changing wheels (tyres and
rims),

  ensure   that   these   are   listed   by  
CITROËN

  for   the   vehicle. Stop as soon as it is safe to do so.
In both cases, contact a CITR
o Ë n
dealer
  or   a   qualified   workshop.
driving safely
SaFETY
5