2015 Citroen BERLINGO MULTISPACE tow

102
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
LOAD SPACE COVER (5 SEAT VERSION)
This rigid shelf conceals the objects stored  in   the   boot. Removing
Fold
  the   load   space   cover.
Detach   it   from   the   notches   A and B
pulling
  it   towards   you.
Raise
  it   and   remove   the   assembly.
Refitting
Place the load space cover in front
of A and B.
Push it forwards to insert the lugs in
the
  notches.
Unfold and clip into the notches C.
Folding
From
  the   boot,   fold   the   half-shelf,  
raising

  it   to   detach   it   from   the   notch   C. Storing (according to version)
A 
location   is   provided   in   the   back   of   the  rear
  seats   to   accommodate   the   load  
space

  cover   folded   onto   itself.
Slide it vertically between the side
guides
  located   at   mid   seat   back   height.
Insert
  the   hinge   first,   with   the   free   flaps  
turned

  upwards.
This rigid load space cover can
form
  a   shelf.   However,   as   a   safety  
measure,

  do   not   place   objects  
on

  it   which   could   become   dangerous  
projectiles

  in   the   event   of   sharp   braking  
or

  rear   impact.
Practical information

103
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
12 volt socket (120 W max)
It is advisable to limit the use of this socket  to   avoid   discharging   the   battery.
Protective net
Open the cover located in the hook support.
Fix the top of the net in the notches,
having
  first   turned   the   bar   1/4   of   a   turn.
Ensure that the end of the bar engages
correctly
  in   the   metal   part   of   its  
location.
Fix the straps in the locations provided
on

  the   floor.
Tighten
  the   net   using   the   straps.
Stowing rings
Use these rings to secure loads on the
floor.
EaSE oF USE and CoMFoRT
4
Practical information

104
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
REAR FITTINGS
(7 SEAT VERSION )
Cup holder
Any liquid carried in a cup (mug or other) on board which could spill,
presents   a   risk.
Take
  care.
12 volt socket (120 W max)
It is advisable to limit the use of this socket   to   avoid   discharging   the   battery.
Stowing rings
Use the stowing rings on the floor to secure  and   retain   your   loads   firmly.
The
  seat   belt   anchorages   must   not   be  
used

  for   this   purpose.
It
  is   recommended   that   the   load   is
 immobilised

  by   securing   it   firmly
 using

  the   stowing   rings   on   the   floor.
Practical information

106
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
BLIND, LOAD SPACE COVER
Position the load space screen so as to
present  the   rear   load   space   cover   flaps  
towards

  you.
Engage the left-hand lug of the roller in
the support A.
The load space cover is the roller blind
type.
 
T

ake
 
care
 
not
 
to
 
place
 
heavy
 
objects

 
on
 
the
 
load
 
space
 
cover
 
when
 
unreeled.
Compress
  then   place   the   right-hand  lug facing the support
B.
Release to engage the roller in its
support.
Unroll the load space cover to the rear
side
  pillars.
Engage the ends in the rear notches to
keep
  it   taut.
To install it
Place the row 3 seats in the fully folded
position.
Raise
 
the
 
storage
 
flap
 
at
 
the
 
boot
 
sill.
Take
 
hold
 
of
 
the
 
roller
 
in
 
the
 
centre
 
and
 
compress

 
it
 
towards
 
the
 
left-hand
 
pillar.
Raise
 
the
 
assembly.
Practical information

 107
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
To remove it
From  the   boot,   pull   the   load   space  
cover

  towards   you   to   release   it   from  
the

  side   pillars.
Guide
  the   load   space   cover   as   it   rolls   up.
Remove
  the   clips   of   the   three   flaps  
from

  the   base   of   each   row   2   head  
restraint.
Compress

  the   roller   to   the   left   to  
remove

  it   from   the   support   B.
Raise
  it   and   pivot   it   forwards. To store it
Store it in the recess at the boot sill,
with
  the   two   rear   flaps   uppermost.
First,
  compress   the   load   space   screen  
to

  the   left.
Release.
Arrange
  the   two   flaps   and   close   the  
storage

  flap.
The
 
roller
 
is
 
fitted
 
with
 
three
 
flaps
 
permitting

 
concealment
 
of
 
the
 
boot, whether the row 2 seats
are

 
in
 
the
 
normal
 
position
 
or
 
the
 
comfort

 
position.
Each
 
flap
 
has
 
two
 
clips
 
which
 
are
 
hooked

 
on
 
the
 
base
 
of
 
each
 
head
 
restraint.
EASE OF USE and COMFORT
4
Practical information

111
Berlingo-2-VP_en_Chap05_Securite_ed01-2015
HAZARD WARNING LAMPS
H
ORN
Press the centre of the steering wheel.
PARKING BRAKE
Applying
Pull the parking brake lever up to immobilise
  your   vehicle.
Check
  that   the   parking   brake   is   applied  
firmly

  before   leaving   the   vehicle.Pull
  on   the   parking   brake   lever,   only
with the vehicle stationary.
In the exceptional case of use of the
parking
  brake   when   the   vehicle   is  
moving,

  apply   the   brake   by   pulling  
gently

  to   avoid   locking   the   rear   wheels  
(risk

  of   skidding).
Press this button, the direction
indicators
 
flash.
They
 
can
 
operate
 
with
 
the
 
ignition
 
off.
The
 
hazard
 
warning
 
lamps
 
should
 
only
 
be used in dangerous situations, when
stopping

 
in
 
an
 
emergency
 
or
 
when
 
driving

 
in
 
unusual
 
conditions.
When
  parking   on   a   slope,   direct   your  
wheels

  towards   the   pavement   and   pull  
the

  parking   brake   lever   up.
There is no advantage in engaging
a
  gear   after   parking   the   vehicle,  
particularly

  if   the   vehicle   is   loaded.
If the parking brake is still on or has not been released properly, this is
indicated
  by   this   warning   lamp   which
 comes

  on   on   the   instrument   panel.
Automatic operation of hazard
warning lamps
When braking in an emergency, depending on the force of deceleration,
the  hazard   warning   lamps   come  
on

  automatically.  
They
  switch   off  
automatically

  the   first   time   you  
accelerate.
It

  is   also   possible   to   switch   them   off   by  
pressing

  the   switch   on   the   dashboard.Releasing
Pull the lever up slightly and press the
button  to   lower   the   parking   brake   lever.
driving safely
SaFETY
5

11 3
Berlingo-2-VP_en_Chap05_Securite_ed01-2015
Activation / DeactivationMalfunction
In the event of a malfunction, the LED in
  the   button   comes   on,   accompanied  
by

  an   audible   signal   and   a   message   in  
the

  screen.
Contact
  a   CITROËN   dealer   or   qualified  
workshop.
Good practice
In bad weather or in winter, ensure that
the  sensors   are   not   covered   with   mud,  
ice

  or   snow.
The
  system   will   be   deactivated  
automatically

  if   a   trailer   is   being   towed  
or

  if   a   bicycle   carrier   is   fitted   (vehicle  
fitted

  with   a   towbar   or   bicycle   carrier  
recommended

  by   CITROËN).
You can activate or deactivate
the
 
system
 
by
 
pressing
 
this
 
button.
The activation or deactivation
of

 
the
 
system
 
is
 
stored
 
when
 
the

 
vehicle
 
stops.
Engage forward gear
In addition to the rear parking sensors, the   front   parking   sensors   are   triggered  
when an obstacle is detected in
front of the vehicle and the speed
of

  the   vehicle   remains   below   6   mph  
(10 km/h).The

  tone   from   the   speaker   (front  
or rear) allows an obstacle to be
identified

  as   either   in   front   of   or  
behind

  the   vehicle.
Stop the assistance
Change to neutral. The   parking   sensor   system  
cannot,

  in   any   circumstances,  
take

  the   place   of   the   vigilance   and  
responsibility

  of   the   driver.
Parking sensors
SaFETY
5

122
Berlingo-2-VP_en_Chap05_Securite_ed01-2015
Operating faults
Sensor fault
The  operation   of   the   laser   sensor   may  
suf

fer   interference   from   accumulations  
of

  dirt   or   misting   of   the   windscreen.  
In this case you are warned by the
display

  of   a   message.
Use
  the   windscreen   demisting  
and regularly clean the area of the
windscreen

  in   front   of   the   sensor.
Do
  not   stick   or   otherwise   fix   any  
object

  on   the   windscreen   in   front  
of

  the   sensor. System fault
In
  the   event   of   a   malfunction   of   the  
system,

  you   are   warned   by   an   audible  
signal

  and   the   display   of   the   message  
"Automatic braking system fault"

.
Have
  the   system   checked   by   a  
CITROËN

  dealer   or   a   qualified  
workshop.In

  the   event   of   an   impact   to  the windscreen at the sensor
,
deactivate
  the   system   and   contact  
a

  CITROËN   dealer   or   a   qualified  
workshop 

to  
have
 
your
 
windscreen
 
replaced.
Never

  try   to   remove,   adjust   or   test  
the

  sensor.
o

nly a CITR o Ë n dealer or a
qualified
  workshop   is   able   to   work  
on

  the   system.
When towing a trailer or when the
vehicle
  is   being   towed,   the   system  
must

  be   deactivated.
driving safely