2015 Citroen BERLINGO MULTISPACE light

20
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
Don't forget
When  leaving   the   vehicle,   check   that  
the lighting is of

f and nothing of value
is
  visible.
a

s a safety precaution (with children
on
  board),   remove   the   key   from   the  
ignition when leaving the vehicle, even
for

  a   short   time.
Good practice
Do not make any modifications to the electronic  immobiliser   system.
Operating
  the   remote   control,   even  
when

  it   is   in   your   pocket,   may   result   in  
involuntary

  unlocking   of   the   doors.
The
  simultaneous   use   of   other  
high

  frequency   equipment   (mobile  
telephones,

  domestic   alarms…),   may  
interfere with the operation of the
remote

  control   temporarily.
The
  remote   control   does   not   operate  
while

  the   key   is   in   the   ignition,   even   if  
the

  ignition   is   off.
ELECTRONIC IMMOBILISER
If you lose your keys
Visit a CITRo Ë n dealer with the
vehicle's
  V5   registration   certificate   and  
your

  identification   document.
a CITR

o Ë n dealer will be able
to
  retrieve   the   key   code   and  
the transponder code so that a
replacement

  key   can   be   ordered.When purchasing a second-hand
vehicle,
  have   the   keys   memorised   by  
a CITR

o Ë n dealer, so as to be sure
that   the   keys   in   your   possession   are  
the only ones that can be used to start
the

  vehicle.
ALARM
If fitted on your vehicle, this provides two
  types   of   protection:
-
 
exterior
  protection:   it   sounds   if   a  
front/rear

  door   or   the   bonnet   is  
opened.
-

 
interior
  protection:   it   sounds   if  
the

  volume   inside   the   passenger  
compartment

  changes   (breaking   of  
a

  window   or   a   movement   inside   the  
vehicle).
If

 
your
 
vehicle
 
is
 
fitted
 
with
 
a
 
separation
 
partition, the interior protection is not
active

  in   the   load   space.
Locking the vehicle with
complete alarm
Setting the alarm
- Switch off the ignition and get out of
the   vehicle.
-
 
Set
  the   alarm   within   five   minutes   of  
getting

  out   of   the   vehicle,   by   locking  
or

  deadlocking   using   the   remote  
control.

 
The
  red   LED,   located   in   the  
button,

  flashes   once   per   second.
All of the keys contain an electronic immobiliser  device.
This
  device   locks   the   engine   supply  
system.

  It   is   activated   automatically  
when

  the   key   is   removed   from   the  
ignition.
a

fter the ignition is switched on, a
dialogue
  is   established   between   the   key  
and

  the   electronic   immobiliser   system.
The
  metal   part   of   the   key   must   be  
unfolded correctly for correct dialogue
to

  take   place.
access

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
28
Dials
1. Distance  recorder   in   kilometres   /  miles.
2.
 
Display
  screen.
3.
 
Fuel
  gauge,   coolant   temperature.
4.
 
Rev
  counter.
5.
 
T
rip   distance   recorder   /   service  
indicator

  reset.
6.
 
Instrument
  panel   lighting   dimmer.Level 1
INSTRUMENT PANELDisplay screens
Screens
The format of the information presented in the screen depends on
the
  vehicle's   equipment   level.
Level 2
with the touch screen tablet
Instruments and controls

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
33Warning lamp isindicatesSolution - action
Coolant
temperature
and level on with needle
in the red
zone.
an
  abnormal   increase   in  
temperature.Park

  and   switch   off   the   ignition   then   allow   to   cool.  
V

isually   check   the   level.
flashing. a
  drop   in   the   coolant   level.Chapter
  7,   "Levels"   section.
Contact
  a   CITROËN dealer   or   a   qualified  
workshop.
Service on

  temporarily. minor   faults   or   warnings.Consult
  the   alert   log   in   the   display   or   screen.
If
  your   vehicle   is   equipped   with   a   trip   computer   or  
a

  screen:   refer   to   the   "Steering   mounted   controls"  
section

  in   Chapter   4.
Contact
  a   CITROËN   dealer   or   a   qualified  
workshop.
remaining

  on. major   faults.
Seat belt not
fastened on then
flashing.
the
  driver   and/or   front  
passenger has not fastened
their

  seat   belt.Pull
  the   strap   then   insert   the   tongue   in   the   buckle.
accompanied
 
by an audible
signal then
remains

  on.the
  vehicle   is   moving   with  
the

  driver's   and/or   front  
passenger's seat belt not
fastened.Check

  that   the   seat   belt   is   fastened   by   pulling   the  
strap.
Chapter

  5,   "Seat   belts"   section.
ECO on.
The
  Stop   &   Start system  
has put the engine in
ST

OP
 
mode   following   a  
vehicle

  stop   (red   light,   traffic  
jam, etc...).As

  soon   as   you   want   to   move   off,   the   warning  
lamp

  goes   off   and   the   engine   restarts  
automatically

  in   START
 
mode.
flashes
  for   a  
few seconds,
then

  goes   off.STOP
 

mode   is   temporarily  
unavailable.
or
ST

ART
 
mode   has   been  
invoked

  automatically.Chapter
  3,   "Stop   &   Start"   section.
Instruments and controls
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
36Warning lamp isindicatesSolution - action
Dipped beam
headlamps /
Daytime
running
lamps on.a
  manual   selection   or  
automatic

  illumination   of  
headlamps.T

urn   the   ring   on   the   lighting   control   stalk   to   the  
second

  position.
illumination of the  dipped  beam  headlamps from
  the   time   the   ignition   is   switched   on: daytime

  running   lamps   (depending   on   the
 country

  in   which   the   vehicle   is   sold).
Chapter 4, "Steering mounted controls" section.
Main beam
headlamps pullin
g
 
of
 
the
 
stalk
 
towards
 
you. Pull

  the   stalk   to   return   to   dipped   beam  
headlamps.
Direction
indicators flashing

 
with
 
audible

 
signal. a change of direction via
the
 
lighting
 
stalk. To
  the   Right:   control   to   be   pushed   upwards.
To
  the   Left:   control   to   be   pushed   downwards.
Front
foglamps on.
a
 
manual
 
selection. The
  foglamps   only   operate   if   the   sidelamps   or  
dipped

  beam   headlamps   are   on.
Rear
foglamps on.
a
 
manual
 
selection. The
  foglamps   only   operate   if   the   sidelamps   or  
dipped

  beam   headlamps   are   on.
In
  conditions   of   normal   visibility,   switch   them   off  
to

  avoid   breaking   the   law.
"This
  lamp   is   a   dazzling   red."
Instruments and controls

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
44
Trip recorder zero reset button
after this operation, if you wish to
disconnect   the   battery,   lock   the  
vehicle

  and   wait   for   at   least   five  
minutes,

  otherwise   the   zero   re-set   will  
not

 
be   registered.
Engine oil level indicator
depending on your vehicle's engine,
when the ignition is switched on, the
engine oil level is indicated for a few
seconds,
  after   the   service   information. Oil level correct
Low oil level
Flashing of "OIL",
linked
  with   the  
service

  warning   lamp,  
accompanied

  by   an  
audible

  signal   and   a   message   in   the  
screen, indicates a low oil level which
could

  damage   the   engine.
If   the   low   oil   level   is   confirmed   by   a  
check

  using   the   dipstick,   it   is   essential  
that

  the   level   is   topped   up.
Oil level gauge fault
Flashing of "OIL--"
indicates a
malfunction   of   the  
engine oil level
indicator
.   Contact   a   CITROËN   dealer  
or

  a   qualified   workshop.
The level read will only be correct
if the vehicle is on level ground
and the engine has been off for
more   than   30   minutes.Dipstick
A
  =   maximum,   never   exceed  
this level as a surplus of oil
may

  damage   the   engine.
Contact a CITR o Ë n dealer
or   a   qualified   workshop  
without

  delay.
B  
=
 
minimum,
 
top
 
up
 
the
 
level
 
via

  the   oil   filler   cap,   using   the  
grade of oil suited to your
engine.
Lighting dimmer
With the ignition on, press
the button until the zeros
appear.
With the lighting on,
press the button to vary
the brightness of the
instruments
  and   controls.  
When the lighting
reaches

  the   minimum   (or  
maximum)

 
setting,   release   the   button  
then press it again to increase (or
reduce)

 
the
 
brightness.
a

s soon as the lighting is of the
required
 
brightness,   release   the   button.
Zero reset
Your CITROËN dealer or a qualified workshop  carries   out   this   operation  
after

  each   service.
However, if you carry out the service
yourself, the re-set procedure is as
follows:
-

switch of
f the ignition,
-

press and hold the trip recorder
reset button,
-

 
switch
  on   the   ignition.
The
  display   begins   a   countdown.
When the display shows "=0", release
the
  button;   the   spanner   disappears.
Instruments and controls

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
45
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
MANUAL GEARBO x
5-speed
6-speed
To change gear easily, always depress
the
 
clutch
 
pedal   fully.
To
 
prevent
 
the
 
mat   from   becoming  
caught

 
under
 
the   pedal:
-
 
ensure

 
that
  the   mat   is   positioned  
and

 
secured   correctly   on   the   floor,
-
 
never

 
fit
 
one   mat   on   top   of   another.
When driving, avoid leaving your hand
on
 
the
 
gear
 
knob   as   the   force   exerted,  
even

 
if
 
slight,
 
may   wear   the   internal  
components

 
of
  the   gearbox   over   time.
Changing into 5th or 6th gear
To engage the gear correctly, move the gear  lever   fully   to   the   right.
STEERING WHEEL ADJUSTMENT
When the vehicle is stationary,
release
  the   steering   wheel   adjustment  
mechanism

  by   pulling   the   lever.
Adjust
  the   steering   wheel   for   height  
and

  reach,   then   lock   the   mechanism   by  
pushing

  the   lever   fully   forward.
Engaging reverse gear
The lever should be moved slowly to  reduce   noise.
To engage reverse gear, wait until the
vehicle
  has   come   to   a   complete   stop.
In
 
the   6-speed   configuration,   raise   the  
collar

  below   the   gear   knob.
Gearbox and steering wheel
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
49
STOP & START
The Stop & Start system puts the engine
  temporarily   on   standby   -   STOP mode

  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).  
The
 
engine

  restarts   automatically   -   START
 mode

  -   as   soon   as   you   want   to   move  
of

f.  
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system
  reduces   fuel   consumption   and  
exhaust

  emissions   as   well   as   the   noise  
level

  when   stationary.
Operation
Going into engine STOP mode
The "ECO"   warning   lamp   comes on
  in   the   instrument   panel   and the

  engine   goes   into   standby:
- with a manual gearbox , at speeds
below   12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with
a 6-speed electronic
gearbox,
  at   speeds   below   5   mph  
(8

  km/h),   when   you   press   the   brake  
pedal or put the gear lever into
position

N. If
  your   vehicle   is   fitted   with   the   system,  
a

  time   counter   calculates   the   sum   of  
the

  periods   in   STOP
 
mode   during   a  
journey

.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With   a   6-speed   electronic  
gearbox,

  for   your   comfort   during  
parking

  manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP
 
mode   does   not   affect   the  
functionality of the vehicle, such as
braking,

  power   steering,   for   example.
n

ever refuel with the engine in
STOP
 
mode;   you   must   switch   off  
the

  ignition   with   the   key.Special cases: STOP mode
unavailable
STOP
 
mode   is   not   invoked   when:
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded
6 mph

  (10   km/h)   since   the   last  
engine

  start   using   the   key,
-  
the
  engine   is   needed   to   maintain  
a

  comfortable   temperature   in   the  
passenger

  compartment,
-  
demisting
  is   on,
-  
some
  special   conditions   (battery  
charge,

  engine   temperature,  
braking

  assistance,   ambient  
temperature...)

  where   the   engine  
is needed to assure control of a
system.
In this case, the
"ECO"
warning   lamp   flashes   for   a  
few

  seconds,   then   goes   off.
This operation is perfectly normal.
Stop & Start
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
54
A FEW DRIVING
RECOMMENDA
TIONS
observe the driving regulations at all
times   and   remain   vigilant   whatever   the  
traffic

  conditions.
Pay
  close   attention   to   the   traffic   and  
keep

  your   hands   on   the   wheel   so   that  
you

  are   ready   to   react   at   any   time   to  
any

  eventuality.
On
  a   long   journey,   a   break   every   two  
hours

  is   strongly   recommended.
In
  difficult   weather,   drive   smoothly,  
anticipate

  the   need   to   brake   and  
increase

  the   distance   from   other  
vehicles.
Driving on flooded roads
We strongly advise against driving
on  flooded   roads,   as   this   could   cause  
serious

  damage   to   the   engine   or  
gearbox, as well as to the electrical
systems

  of   your   vehicle. If you are obliged to drive through
water:
-
 
check
  that   the   depth   of   water   does  
not

  exceed   15   cm,   taking   account  
of

  waves   that   might   be   generated  
by other users,
-
 
deactivate
  the   Stop   &   Start   system,
-
drive as slowly as possible without
stallin

g.   In   all   cases,   do   not   exceed  6
  mph   (10   km/h),
- do not stop and do not switch of f
the
  engine.
On
  leaving   the   flooded   road,   as   soon  
as

  circumstances   allow,   make   several  
light

  brake   applications   to   dry   the   brake  
discs

  and   pads.
If in doubt on the state of your vehicle,
contact a CITR
o Ë n dealer or a
qualified
  workshop.Never
  drive   with   the   parking   brake  
applied

  -   Risk   of   overheating   and  
damage

  to   the   braking   system!
Do   not   park   or   run   the   engine   when  
stationary

  in   areas   where   inflammable  
substances

  and   materials   (dry   grass,  
dead

  leaves...)   might   come   into   contact  
with

  the   hot   exhaust   system   -   Risk   of  
fire!
n

ever leave a vehicle
unsupervised with the engine
running.   If   you   have   to   leave  
your vehicle with the engine running,
apply

  the   parking   brake   and   put   the  gearbox into neutral or position
N or P,
depending
  on   the   type   of   gearbox.
Important!
Starting and stopping