2015 Citroen BERLINGO MULTISPACE instrument panel

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
37
Warning lamp in the
screenis
indicates Solution - action
Cruise
control on.
cruise
  control   selected.Manual
  selection.
Chapter
  4,   "Steering   mounted   controls"   section.
Speed limiter on.speed
  limiter   selected.Manual
  selection.
Chapter
  4,   "Steering   mounted   controls"   section.
Gear shift
indicator on.a
  recommendation  
independent of the type and
density

  of   traffic.To
  reduce   fuel   consumption,   change   to   an  
appropriate

  gear   with   a   manual   gearbox.
The driver retains responsibility to follow this
indication
  or   not.
Diesel pre-
heating on.climatic
  conditions   requiring  
pre-heating.W

ait   until   the   warning   lamp   goes   off   before  
operating

  the   starter.
Presence of
water in the
Diesel filter
on and
accompanied by
  a   message   in
 the

  screen.
water in the Diesel filter. Have   the   filter   bled   by   a   CITROËN   dealer   or   a  qualified
  workshop   without   delay.
Chapter   7,   "Checks"   section.
According
  to   country.
Service
spanner on.that a service will be due
shortly. Refer
  to   the   list   of   checks   in   the   maintenance   and  
warranty

  guide.
Have the service carried out by a CITR
o Ë n
dealer
  or   a   qualified   workshop.
Time flashing. adjustment
  of   the   time.Use
  the   left-hand   button   on   the   instrument   panel.
Chapter
  3,   "Instruments   and   controls"   section.
Instruments and controls
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
41
EMISSIONS CONTROLS
EoBd (European on Board diagnosis) is a diagnostics
system
  which   complies   with,
 among

  others,   the   standards
 on

  the   authorised   emissions   of:
-
 
CO

 
(carbon   monoxide),
-

HC (unburnt hydrocarbons),
-

no
x (nitrous oxides) or particles,
detected by oxygen sensors placed
upstream
  and   downstream   of   the  
catalytic

  converters.
The
 
driver
 
is
 
warned
 
of
 
any
 
malfunction
 
of

 
this
 
emission   control   system   by   the  
illu

mination   of   this   specific   warning  
lamp

 
in
 
the   instrument   panel.
There
 
is
 
a   risk   of   damage   to   the  
catalytic

 
converter.   Have   it   checked  
by

 
a
 
CITROËN   dealer   or   a   qualified  
workshop.
UNDER-INFLATION DETECTION
This system continuously  monitors  
the pressures of the four
tyres, as soon as the
vehicle

  is   moving.
a pressure sensor is located in the
valve of each tyre (except the spare
wheel).
The

 
system
 
triggers   an   alert   if   a   drop  
in

 
pressure
 
is
 
detected   in   one   or   more  
tyres.The

 
tyre
 
under-inflation   detection  
system

 
is
 
an   aid   to   driving   which  
does not replace the need for
vigilance

 
on   the   part   of   the   driver.This
  system   does   not   avoid   the  need
  to   check   the   tyre   pressures  
regularly (including the spare
wheel)

  and   before   a   long   journey.
Driving
  with   under-inflated   tyres  
adversely af

fects road holding,
extends
  braking   distances   and   causes  
premature

  tyre   wear,   particularly   under  
arduous conditions (vehicle loaded,
high

  speed,   long   journey).
Driving
  with   under-inflated   tyres  
increases

  fuel   consumption.
The tyre pressures for your vehicle
can be found on the tyre pressure
label.
Refer
  to   chapter   9,   "Identification  
markings"

  section.
The
  tyre   pressures   must   be   checked  
when the tyres cold (vehicle stopped
for 1 hour or after driving for less then
6

  miles   (10   km)   at   moderate   speed).
Otherwise,
  add   0.3   bar   to   the   values  
indicated

  on   the   label.
Instruments and controls
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
46
The information appears in the  instrument   panel   in   the  
form

  of   an   arrow.
The
  system   adapts   its   gear  
change

  recommendation  
according to the driving conditions
(slope,

 
load, ...)   and   the   demands  
of the driver (power

, acceleration,
braking, ...).
The
 
system   never   suggests:
-
 
engaging
  first   gear,
-
 
engaging
  reverse   gear.
With
 
an
 
electronic
 
gearbox,
 
the
 
system
 
is

 
only
 
active
 
in
 
manual
 
mode.
GEAR SHIFT INDICATOR
System which reduces fuel consumption   by   recommending   the  
most

  appropriate   gear.
Operation
depending on the driving situation and
your   vehicle's   equipment,   the   system  
may

  advise   you   to   skip   one   (or   more)  
gear(s).

 
Y
ou   can   follow   this   instruction  
without

  engaging   the   intermediate  
gears.
The

  gear   engagement  
recommendations

  must   not   be  
considered

  compulsory.   In   fact,   the  
configuration

  of   the   road,   the   amount  
of

  traffic   and   safety   remain   determining  
factors when choosing the best
gear

.  
Therefore,
  the   driver   remains  
responsible for deciding whether or
not to follow the advice given by the
system.
This

  function   cannot   be   deactivated.
Gearbox and steering wheel

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
47
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
6-SPEED ELECTRONIC GEARBOx
- automatic  mode:   gear   selector   in  position
A.
-
 
manual
  mode:   gear   selector   in  
position

M.
For
  safety:
It
  is   only   possible   to   come   out  
of position

N   if   the   brake   pedal   is  
pressed.
The

  change   from   position   A (driving in
automatic
  mode)   to   position   M (driving
in
  manual   mode)   or   vice   versa   can   be  
made

  at   any   time.  
The
  warning   lamp   A
goes
  off   in   the   instrument   panel.
Mode selection Moving off
- To start the engine, the gear
selector   must   be   in   position   N.
-
 
Press
  firmly   on   the   brake   pedal.
-
 
Operate
  the   starter.
-

When the engine is running, place
the gear selector on

R, A or M as
desired.
-
 
Release
  the   brake   pedal   and  
accelerate.
If the gear selector is not in position

N,
and/or
  if   the   brake   pedal   is   not  
pressed,

  the   engine   will   not   start.  
Repeat

  the   above   procedure.
Reverse gear Engaging reverse gear
Move the gear selector to R.
Only attempt to select reverse gear
when the vehicle is stationary.
Neutral Changing to neutral
Move the gear selector to N.
  If   the  
vehicle

  is   moving,   do   not   select   this  
position

  even   momentarily.
Gearbox and steering wheel
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
48
Acceleration
For optimum acceleration (e.g. to overtake  another   vehicle),   simply  
press the pedal beyond the point of
resistance at the end of its travel, by
pressing

  down   firmly.
Vehicle stationary, with the
engine running
In the event of a prolonged stop with
the engine running, the gearbox
changes  automatically   to   neutral   N.
Stopping the vehicle
Before stopping the engine, put the
gear selector in position N.
In all cases, it is essential to apply
the
  parking   brake.   Check   that   the  
parking

  brake   warning   lamp   is   on   in   the  
instrument

  panel.
Before doing anything in the
engine
  compartment,   check   that  
the gear selector is in neutral

N.
Changing gear
In situations of high engine speeds
(heavy acceleration), a change
up will not occur unless the driver
operates the electronic gearbox control
paddle. Pull on the "+" control
paddle
  to   change   up.
Pull on the "-" control
paddle to change
down.
-

If the vehicle stops or reduces
speed

  (for   example   when  
approaching a stop sign),
the gearbox changes down
automatically

,   to   first   gear   if  
needed.
-


It is not necessary to release the
accelerator

  completely   during   gear  
changes.
-

a
gear change instruction is
accepted only if the engine speed
permits.
-


For safety reasons, depending on
the engine speed, a change down
may

  be   performed   automatically.
Manual mode
Changing to manual mode
Move the gear selector to M. Automatic mode Changing to automatic
mode
Move the gear selector to A.
The gearbox then operates in
automatic
 
mode,
 
without
 
any
 
action
 
on
 
your

 
part.
It constantly selects the gear that is
best
 
suited
 
to
 
the
 
following
 
conditions:
-

driving style,
-

 
road

 
profile,
-
 
optimum

 
fuel
 
consumption.
Gearbox and steering wheel

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
49
STOP & START
The Stop & Start system puts the engine
  temporarily   on   standby   -   STOP mode

  -   during   stops   in   the   traffic   (red  
lights,

  traffic   jams,   or   other...).  
The
 
engine

  restarts   automatically   -   START
 mode

  -   as   soon   as   you   want   to   move  
of

f.  
The
  restart   takes   place   instantly,  
quickly

  and   silently.
Perfect for urban use, the Stop & Start
system
  reduces   fuel   consumption   and  
exhaust

  emissions   as   well   as   the   noise  
level

  when   stationary.
Operation
Going into engine STOP mode
The "ECO"   warning   lamp   comes on
  in   the   instrument   panel   and the

  engine   goes   into   standby:
- with a manual gearbox , at speeds
below   12   mph   (20   km/h),   when   you  
put the gear lever into neutral and
release the clutch pedal,
-


with
a 6-speed electronic
gearbox,
  at   speeds   below   5   mph  
(8

  km/h),   when   you   press   the   brake  
pedal or put the gear lever into
position

N. If
  your   vehicle   is   fitted   with   the   system,  
a

  time   counter   calculates   the   sum   of  
the

  periods   in   STOP
 
mode   during   a  
journey

.   It   rests   itself   to   zero   every   time  
the

  ignition   is   switched   on   with   the   key.
With   a   6-speed   electronic  
gearbox,

  for   your   comfort   during  
parking

  manoeuvres,   STOP
 
mode  
is not available for a few seconds after
coming

  out   of   reverse   gear.
STOP
 
mode   does   not   affect   the  
functionality of the vehicle, such as
braking,

  power   steering,   for   example.
n

ever refuel with the engine in
STOP
 
mode;   you   must   switch   off  
the

  ignition   with   the   key.Special cases: STOP mode
unavailable
STOP
 
mode   is   not   invoked   when:
-
the driver's door is open,
-

the driver's seat belt is not
fastened,
-

the vehicle has not exceeded
6 mph

  (10   km/h)   since   the   last  
engine

  start   using   the   key,
-  
the
  engine   is   needed   to   maintain  
a

  comfortable   temperature   in   the  
passenger

  compartment,
-  
demisting
  is   on,
-  
some
  special   conditions   (battery  
charge,

  engine   temperature,  
braking

  assistance,   ambient  
temperature...)

  where   the   engine  
is needed to assure control of a
system.
In this case, the
"ECO"
warning   lamp   flashes   for   a  
few

  seconds,   then   goes   off.
This operation is perfectly normal.
Stop & Start
REadY To Go
3

Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015Berlingo-2-VP_en_Chap03_Pret-a-partir_ed01-2015
51
Reactivation
Press the "ECO OFF" switch again.
The   system   is   active   again;   this   is  
confirmed

  by   the   switch   warning  
lamp

  going   off   and   a   message   in   the  
instrument

  panel.
The
  system   is   reactivated  
automatically

  at   every   new   start  
using

  the   key.
Operating fault
In the event of a malfunction with  the   system,   the   "ECO
OFF"
  switch   warning   lamp  
flashes,

  then   comes   on  
continuously

.
Maintenance
Before working under the bonnet, deactivate  the   Stop   &   Start   system  
to

  avoid   any   risk   of   injury   resulting  
from

  automatic   operation   of   START
 mode.
This

  system   requires   a   specific  
battery

  with   a   special   specification  
and

 
technology   (reference   numbers  
available

  from   a   CITROËN   dealer   or   a  
qualified

  workshop).
Fitting a battery not listed by
CITROËN introduces
  the   risk   of  
malfunction

  of   the   system.
The
  Stop   &   Start   system   makes  
use

  of   advanced   technology.  
All
 
work

  on   this   type   of   battery   must  
be done only by a CITR

o Ë n dealer or
a
 
qualified   workshop.
have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or

 
a
 
qualified
 
workshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 

mode,
 
the

 
vehicle
 
may
 
stall.
 
All

 
of
 
the
 
warning
 
lamps

 
in
 
the
 
instrument
 
panel
 
come
 
on.

 
It
 
is
 
then
 
necessary
 
to
 
switch
 
off
 
the ignition and start the engine again
using

 
the
 
key.
Stop & Start
REadY To Go
3

55
Berlingo-2-VP_en_Chap04_Ergonomie_ed01-2015
DIRECTION INDICATORS
"Motorway" function
Press  the   control   up   or   down   to   flash  
the corresponding direction indicator
three

  times.
LIGHTING
Left: downwards passing the point  of   resistance.
Right:
  upwards   passing   the  
point

  of   resistance.
Front and rear lighting
Lighting off
Automatic
  illumination   of  
headlamps
SidelampsDipped

  beam   (green)
Dipped beam/main beam change
Pull
 
the
 
stalk   fully   towards   you.
Lighting-on audible warning
o

n switching off the ignition, all of the
lamps
 
turn   off,   except   dipped   beam   if  
automatic

  guide-me-home   lighting   has  
been

 
activated.
 Checking

 
by
 
means
 
of
 
the
 
indicator
 lamps

 
in
 
the
 
instrument
 
panel
 
is
 described

 
in
 
the
 
"Instruments
 
and
 controls"

 
section
 
of
 
chapter
 
3.
Direction indicators
Selection is by turning this
ring. Main
  beam   (blue)
To activate the lighting
control, turn this ring to
the lighting off position "0"
then to the selection of
your   choice.
o

n opening the driver's door, there is
an audible warning if you have left the
lighting
  on.
Steering mounted controls
EaSE oF USE and CoMFoRT
4