2015 AUDI S8 belt

194 Audi pre sense
Audi pre sense
Preventative passenger
protection
A pp lies to veh icles: with Audi pre se nse
Audi pre sense can initiate steps to help pro­
tect vehicle occupants in certain situations.
The functions described depend on equ ipment
installed in your vehicle:
Audi pre sense basic
The following functions can be triggered in
certain driving situations:
- Tightening of the safety belts (for example,
during heavy braking) : the front safety belts
have reversible belt pretensioners. If a colli­
sion does not occur, the safety belts loosen
slightly and are ready to be tightened again.
- Closing the windows and the sunroof*: the
windows and the sunroof* close leaving a
small open gap.
Audi pre sense basic functions can be trig­
gered at speeds above 20 mph (30 km/h). The
deployment time is adapted in the drive select
mode dynamic.
Audi pre sense front (vehicles with
adaptive cruise control*)
Audi pre sense front includes the functions in
Audi pre sense basic. In addition, within the
limits of the system, the likelihood of a colli­
sion with the vehicle immediately ahead is al­
so calculated .
If the system senses an immi­
nent collis io n the following functions can be
triggered:
- Braking guard
~page 98
-Tightening the safety belts
- Closing the windows and the sunroof* (leav-
ing a small open gap)
Audi pre sense rear (vehicles with Audi
side assist*)
Audi pre sense rear includes the functions in
Audi pre sense basic. In addition, the likeli­
hood of a rear-end coll ision with the veh icle
coming from behind is also calculated. If the risk
of a co llision is detected, the following
functions can be triggered:
- Tig htening the safety belts
- Closing the windows and the sunroof* (leav-
ing a small open gap)
- Adjusting the seats: the settings for the
power head restrains, the upper sections of
the backrests and the pneumatic side bol­
sters* are optimized for the front seats and
the outboa rd rear seats*. If a collision does
not occur, the previous seat settings are re­
stored.
Audi pre sense plus
Audi pre sense plus includes the funct ions in
Audi pre sense front and Audi pre sense rea r.
Error message
Audi pre sense: not available
Preventative passenger protection is not avail­
able. See your authorized Audi dealer immedi­
ately to have the malfunction corrected .
A WARNING
-Audi pre sense cannot overcome the laws
of physics.
It cannot prevent a collision. Do
not let the increased safety provided
tempt you to take risks. This will increase
the risk of a collision and serious personal
injuries.
- The sensors cannot always detect all ob­
jects . This increases the risk of a colli­
sion.
- Audi pre sense does not detect people or
animals or objects that are crossing the
vehicle's path~
page 92.
-The radar sensor's vision can be reduced
by heavy rain, ice, snow, heavy road spray
and reflections from guard rails, tunnel
entrances, etc. These and similar condi­
tions can prevent vehicles from being ac­
curately detected and in some cases they
may not be detected at all.
Ill>

196 Intelligent technology
Intelligent technology
Notice about data
recorded by the Event
Data Recorder and
vehicle control modules
E ve nt Data Recorder
This vehicle is equipped with an Event Data
Recorder (EDR) . The main purpose of an EDR
is to record, in certain crash or near crash-like
situations, such as an airbag deployment or hitting a road obstacle, data that will assist in
understand ing how a veh icle's systems per­
formed. The EDR is designed to record data
re lated to vehicle dynamics and safety sys­
tems for a short period of time, typically
30 seconds or less. The EDR in this vehicle is
designed to record such data as:
- How various systems in you r vehicle were
operating;
- Whether or not the d river and passenger
safety belts were buckled/fastened;
- How far (if at all) the driver was dep ress ing
the accelerator and/or brake pedal; and,
- How fast the vehicle was traveling.
These data can help provide a better under­
stand ing of the cir cumstances in which crash­
es and injuries occur . NOTE : EDR data are re­
corded by your vehicle only if a non-trivial
crash situation occurs; no data are recorded by
the EDR under normal driving conditions and
no personal data (e.g., name, gender, age,
and crash location) are recorded. However,
other parties, such as law enforcement, cou ld
comb ine the EDR data with the type of per­
sonally identifying data routinely acquired
during a crash investigation.
To read data recorded by an EDR, special
equipment is required, and access to the vehi­
cle or the EDR is needed. In addition to the ve­ hicle manufacturer, other parties, such as law
enforcement, that have the special equip­
ment, can read the information if they have
access to the vehicle or the EDR. Some state
laws restrict the retrieval or down­
loading of data stored by ED Rs installed in a
vehicle for the express purpose of retrieving
data after an accident or crash event without
the owner's consent .
Audi will not access the EDR and/or simi lar
data or g ive it to others -
- un less the vehicle owner (or lessee if the ve ­
hicle has been leased) agrees; or
- upon the official request by the police; or
- upon the ord er of a court of law or a govern-
ment agency; or
- for the defense of a lawsuit through the ju­
dicia l discovery p rocess.
- Aud i may also use the data for research
about vehicle operat ion and safety perform­
ance or provide the data to a third party for
research purposes without identifying the
specif ic vehicle or information about the
identity of its owner or lessee and only after
the recorded vehicle data has been ac­
cessed.
Vehicle control modules
You r vehicle is also equ ipped with a number of
electron ic control modules for various vehicle
systems, such as engine management, emis­
sion control, airbags, and safety belts.
T hese electronic control mod ules record data
during norma l vehicle operation that may be
needed by trained technicians for diagnostic
and repair purposes. The recording capability
of these modu les is limited to data (no sound
is recorded). Only a small amount of data is
actually recorded over a very lim ited period of
t ime, or stored when a system fault is detect­
ed by a contro l modu le. Some of the data
stored may relate to vehicle speed, direction,
o r braking, as well as restraint system use and
performance in the event of a crash. Stored
data can also only be read and downloaded
with special equipment that is directly con-
nected to the vehicle. .,..

,....,
N ,....,
N
0 J:
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Vehicle care and cleaning 217
Component Situation Solution
Safety belts
Dirty Mild soap solutional, allow to dry before letting them re-
tract
Textiles, Stains adhering to Vacuum cleaner
Vinyl, the surface
Alcantara Water-based stains Absorbent cloth and mild soap solutiona>
such as coffee, tea,
blood, etc.
Oi l-based stains Apply a mild soap solutional, blot away the dissolved oil
such as oil, make- or dye, treat afterward with water, if necessary
up, etc .
Special stains such Special stain remover, blot with absorbent material,
as ballpoint pen, treat afterward with mild soap solutiona>, if necessary
nail polish, latex
paint, shoe polish,
etc.
Natural leather Fresh stains Cotton cloth with a mild soap solutiona >
Water-based stains Fresh stains: absorbent cloth
such as coffee, tea, Dried stains: stain remover suitable for leather
blood, etc.
Oil-based stains Fresh stains: absorbent cloth and stain remover suitable
such as oil, make- for leather
up, etc. dried stains: Oil cleaning spray
Special stains such Stain remover suitable for leather
as ballpoint pen ,
nail polish, latex
paint, shoe polish,
etc.
Care Regularly apply condit ion ing cream that protects from
light and penetrates into the material. Use specially-col-
ored conditioning cream, if necessary.
Cooler Dust and dirt Clean the ventilation openings in the luggage compart-
ment
Dirty Lukewarm
water, mild soap solutional if necessary, then
dry
Defrosting Empty the refrigerator, switch it off and let it thaw with
the door open, then dry
Carbon parts Dirty Clean the same way as p lastic parts
a) Mild soap so lu tion : maxim um two ta bl es poons neutr al soa p in 1 q uar t (l lit e r) of water
A WARNING
The windshield may not be treated with
water-repelling windshield coating agents.
Unfavorable conditions such as wetness,
darkness, or low sun can result in in- creased
glare. Wiper blade chatter is also
possible.
([) Note
-Headlights/tail lights
•
•

218 Vehicle care and cleaning
- Never clean headlights or tail lights
with a dry cloth or sponge.
- Do not use any cleaning product that
contains alcohol, because they could
cause cracks to form.
-Wheels
- Never use any paint polish or other
abrasive materials.
- Damage to the protective layer on the
rims such as stone chips or scratches
must be repaired immediately.
- Sensors/camera lenses
- Never use warm or hot water to re-
move snow or ice from the camera
lens. This could cause the lens to crack.
- Never use abrasive cleaning materials
or alcohol to clean the camera lens.
This could cause scratches and cracks.
-Windows
- Remove snow and ice on windows and
exterior mirrors with a plastic scraper.
To avoid scratches, move the scraper
only in one direction and not back and
forth.
- Never remove snow or ice from win­
dows and mirrors using warm or hot
water because this could cause cracks
to form.
- To avoid damage to the rear window
defogger, do not apply any stickers on
the heating wires on the inside of the
window.
- Decorative parts/trim
- Never use chrome care or cleaning
products.
- Paint
-To reduce the risk of scratches, the ve-
hicle must be free of dirt and dust be­
fore polishing or waxing.
- To prevent paint damage, do not polish
or wax the vehicle in direct sunlight.
- To reduce the risk of paint damage, do
not polish away rust film .
- Remove cosmetics and sunblock imme­
diately. Otherwise, the paint could be
damaged .
-Trim
- To reduce the risk of damage, do not
treat the trim around the panorama
sunroof with paint polish.
- Decorative decals
-To reduce the risk of damage, do not
use any rough powder or abrasive
cleaning products .
- To reduce the risk of damage, do not
polish decorative parts that have a
matte finish .
-Displays
-To avoid scratches, do not use dry
cleaning methods on displays.
- Controls
- Make sure that no fluids enter the con-
trols, because this could cause dam­
age.
- Safety belts
- Do not remove the safety belts to clean
them.
- Never clean safety belts or their com­
ponents chemically or with corrosive
fluids or solvents and never allow
sharp objects to come into contact
with the safety belts. This could cause
damage to the belt webbing.
- If there is damage to the webbing, the
connections, the retractors or the buck­ les, have them replaced by an author­
ized Audi dealer or a qualified work­
shop.
- Textiles/Vinyl/Alcantara
- Never treat Vinyl/Alcantara with leath-
er care products, solvents, floor polish,
shoe polish, stain remover or similar
products.
- To avoid damage, have stubborn stains
removed by an authorized Audi dealer
or a qualified workshop.
- Never use steam cleaners, brushes,
hard sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry
the seat.
- Objects with sharp edges such as zip­
pers, rivets on clothing or belts can
cause damage to the surface.

,....,
N ,....,
N
0 J:
"": ,...., \!) ..,.,
,...., ..,., ,....,
-Open hook and loop fasteners, for ex­
ample on clothing, can damage seat
covers . Make sure hook and loop fas­
teners are closed.
- Natu ral leather
- Never treat leather with solvents, floor
polish, shoe polish, stain remover or
sim ilar products.
- Objects with sharp edges such as z ip­
pers, rivets on clothing or belts can
cause damage to the surface.
- Never use steam cleaners, brushes,
hard sponges, etc. when clean ing .
- Do not turn on the seat heat ing* to dry
the seat.
- To help prevent the leather from fad­
ing, do not leave the veh icle in direct
sunlight for long periods of time. If
leaving the vehicle parked for long pe­
r iods of time, you should cover the
leather to protect it from direct sun ­
light.
-Co oler
- Do not try to speed up the defrosting
process by applying heat.
- To help prevent health risks or damage
to the cooler, do not use any abrasive
cleaners, solvents, wax or strongly
scented or aggressive cleaning prod ­
ucts .
- Do not clean the cooler with rough
cleaning tools such as steel wool.
@ Tips
-Insects are eas ier to remove from paint
that has been freshly waxed .
- Regu lar waxing can prevent rust film
from forming .
Vehicl e ca re a nd cl eanin g 219
•
•

,....,
N ,....,
N
0 J:
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
-Always disconnect the battery.
- Never smoke or work near heaters or open flames. Fluids in the engine com­
partment could start a fire.
- Keep an approved fire extinguisher im­
mediately available.
- To avoid electrical shock and personal in­
jury while the engine is running or being
started, never touch :
- Ignition cables
- Other components of the high voltage
electronic ignition system.
- If you must perform a check or repair
with the engine running:
- First, fully apply the parking brake,
move selector lever to "P" (Park).
- Always use extreme caution to prevent
clothing, jewelry, or long hair from get­
ting caught in the radiator fan, V-belts
or other moving parts, or from contact­ ing hot parts. Tie back hair before
starting, and do not wear clothing that
will hang or droop into the engine.
- Minimize exposure to emission and
chemical ha zards c:::> & .
A WARNING
California Proposition 65 Warning:
- Engine exhaust, some of its constituents,
and certain vehicle components contain
or emit chemicals known to the State of
California to cause cancer and birth de­
fects and reproductive harm. In addition ,
certain fluids contained in vehicles and
certain products of component wear con­
tain or emit chemicals known to the
State of California to cause cancer and
birth defects or other reproductive harm .
Checking and filling 229
-Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive harms. Wash hands after handling.
(D Note
When adding fluids, always make sure that
they are poured into the proper container
or filler opening, otherwise serious dam­
age to vehicle systems will occur.
(® For the sake of the environment
To detect leaks in time, inspect the vehicle
floor pan from underneath regularly . If
you see spots from oil or other vehicle flu­ ids, have your vehicle inspected by an au­
thorized Audi dealer.
Closing the engine hood
.,. Pull the hood down until the pressure from
the struts is reduced.
"'Let the hood
drop down and latch in place.
Do not try to push it shut; it may fail to en­
gage
c:::> ,A .
A WARNING
-
A hood that is not completely latched
could fly up and block your view while driv ­
ing .
- When you close the engine hood, check it
to make sure the safety catch has proper­ ly engaged. The hood should be flush
with the surrounding vehicle body parts.
- If you notice while driving that the hood
is not secured properly , stop at once and
close it. •
•

238 Check ing and filling
• Let the engine coo l down .
• Place a thick rag over the coolant expansion
tank
¢ page 237, fig . 204 and care full y
twist the cap counter-clockwise¢ _&..
• Add coolant mixed in the correct ratio
¢
page 236, Coolant up to the MAX mark­
i ng.
• Make sure that the fluid level rema ins sta-
ble. Add more coolant if necessary.
• Twist the cap on again
tightly.
Replacement engine coolant must conform to
exact specifications ¢
page 236, Coolant.
We recommend using only coolant additive
G12++, G13 or in an emergency G12+ . Do not
use a different additive . In an emergency use
p la in water unt il you can get the correct add i­
tive and can restore the correct ratio. This
should be done as soon as possible .
If you have lost a considerable amount of
coolant, then you should add co ld antifreeze
and cold water only when the engine is co ld.
Always use
new eng ine coolant when refilling .
Do not fi ll coolant above the "MAX" mark. Ex­
cess coolant will be forced out through the pressure relief valve in the cap when the en­
g ine becomes hot .
A WARNING
- T he coo ling system is under p ressure and
can get very hot. Reduce the risk of
scalding from ho t coolant by following
these steps.
-Turn off the eng ine and a llow it to cool
down.
- Protect your face, hands and arms from escaping flu id and steam by cover ing
the cap with a large, thick rag.
- T urn the cap slowly and very carefully
in a counter-clockwise d irect ion while
apply ing light, downward pressure on
the top of the cap.
- To avo id being burned, do not sp ill an­
tifreeze or coolant on the exhaust sys­
tem or hot engine parts . Under certa in cond
it ions, the ethylene g lycol in en­
gine coolant can catch fire.
- Antifreeze is poisonous . A lways store an­
tifreeze in its origina l container and well
out of the reach of children.
- If you dra in the coo lant, it must be
caught and safely stored in a proper con­
tainer clearly marked "po ison".
@ Note
- Do not add coolant if the expansion tank
is empty. Air co uld enter the cooling sys­
tem and damage the engine. If this is
the case, do not cont inue driving. Seek
professional assistance .
- Coo lant pollutes the environment and
cou ld cause an engine f ire. Excess cool­
ant will be forced out through the pres­
sure relief valve in the cap when the en­
gine becomes hot.
- If, in an eme rgency, only wate r can be
added, the co rrect ratio between water
and antifreeze ¢
page 236 must be re­
stored as soon as possible.
@ For the sake of the environment
D rained coolant should not be reused . Al­
ways d ispose of used coolant while observ­
i ng all envi ro nmental regula tions.
Radiator fan
The radiator fan switches on automatically by
itself
The rad iator fan is driven by the e ngine via the
V-belt. The viscous clutch regulates the speed of the fan acco rding to the temperatu re of the
coolant.
An auxiliary electric radiato r fan* sw itches on
and off depending on coolant temperature
and ot her vehicle ope rat ing condit io ns.
After you switch the eng ine off, the aux iliary
fan can continue running for up to 10 m inutes
- even w ith the ignition off .
It can even switch
o n aga in later by itself¢.& , if
1111>

,....,
N ,....,
N
0 J:
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
th e f unct ion of the tire pressure monitor­
ing system*.
- Always inflate tires to the recommended
and correct tire pressure before driving
off.
- Driving with under inflated tires bend
more, letting them get too hot resu lting
in tread separation, sudden t ire failure
and loss of control.
- Excessive speed and/overloading can
cause heat build-up, sudden tire fail ure
and loss of control.
- If the t ire pressure is too low or too high,
the tires w ill wea r prematurely and the
vehicle will not hand le we ll.
- If the t i re is not flat and you do not have
to change a w heel immed iate ly, dr ive at
reduced speed to the nearest serv ice sta­
t ion to check the tire pressure and add
air as requi red.
{Q) Note
Dr iving without va lve stem caps ca n cause
damage to the tire va lves . To preve nt this,
always ma ke s ure t hat facto ry installed
va lve stem caps on all wheels a re secu re ly
mounte d on the va lve.
@ For the sake of the environment
Unde rinflat ed tires will a lso inc reas e the
fue l cons umption .
Tires and vehicle load limits
There are l imits to the amo un t of load or
weight that any vehicle and any tire can carry .
A veh icle that is overloaded w ill not handle
w ell and is more difficult to stop. Overload ing
can not only lead to loss of vehicle contro l,
but c an a lso damage import ant parts of the
ve hicle and can lead to sudden tire failure, in­
cluding a blowout and sudden deflation that
can cause the ve hicle to crash .
Your safety and that of your passengers a lso
depends on making sure that load limits are n ot exceeded. Vehicle load includes everybody
and everyth ing in and on the vehicle . Th ese
Tire s an d wheel s 253
load lim its are technically referred to as the
vehicle's
Gross Vehicle Weight Rating
("GVWR").
T he "GVWR" incl udes the weight of the basic
vehicle, a ll factory installed accessories, a f ull
tan k of fuel, oi l, coo lant and other fluids plus
max imum load. The max imum load incl udes
the n umber of passengers t hat the vehicle is
intended to carry ("seat ing capac ity") with an
ass umed we ight of 150 lbs (68 kg) fo r each
passenger at a designated seating posi tion
and the tota l weight of a ny luggage i n the ve­
hicle. If you tow a tra ile r, the we igh t of the
tra iler hi tch and the tongue we igh t of t he
loaded tra iler mus t be included as part of the
vehicle load .
T he
Gro ss Axle Weight Rating (" G AWR ") is
the max imum load th at can be appl ied a t each
of the veh icle's two axles .
T he Gross Vehicle Weight Rat ing and t he
G ross Ax le Weig ht Ra ting are listed on the
sa fe ty comp lian ce sti cke r la bel lo cate d on the
driver's side B-pillar. Yo ur Audi has
5 seat ing
pos itions , 2 in the front and 3 in the rea r for
total seating capacity of 5. Vehicles with pow­ er indiv idual rear seats* have 4 seating posi­
tions, 2 in the front and 2 in the rear for total
seat ing capac ity of 4. Each seating position
has a safety belt
c::> page 143, Safety belts.
T he fact that there is an upper limit to you r
vehicle's Gross Vehicle Weight Rating means
that the to tal weight of whatever is being car­
ried in the vehicle ( includ ing t he weight of a
tra ile r hitch a nd the tongue we ight of t he
loaded tra ile r) is lim ited. The more passen­
gers in the vehicle or passe ngers who are
heavier th an the sta ndard we ights assumed
mean tha t less we igh t can be carried as lug­
gage.
T he tire pressure label o n your Aud i also lis ts
the max imum combined weight of all of the
occupants and l uggage or other cargo that
the ve hicle can carry. For the location of the
l abel
c::> page 249, fig . 208. IJ>-
•
•