
Instruments and indicator lights
reached the reserve mark, the bottom LED will
turn red and the
ljJ indicator light turns on
¢
page 23. The bottom LED blinks red when
the fuel level is very low.
The on-board computer shows the range based
on the fuel level¢
page 28, On-board comput
er display.
For the tank capacity in your vehicle, refer to the
Technical Data
¢ page 260.
(D Note
Never drive until the tank is completely emp
ty. The irregular supply of fuel that results
from that can cause engine misfires. Uncom
busted fuel will then enter the exhaust sys
tem. This can cause overheating and damage
to the catalytic converter.
Coolant temperature indicator
In vehicles without a coolant temperature indica
tor, an indicator light. will turn on when the
coolant temperature is too high ¢
page 19. Re
fer to ¢(1) .
The coolant temperature indicator @c:>
page 10,
fig . 3 only works when the ignition is switched
on . To prevent engine damage, please observe
the following notes about the temperature rang
es.
Cold range
If only the LEDs at the bottom of the gauge turn
on, the engine has not reached operating tem perature yet. Avoid high engine speeds, full accel
erating and heavy engine loads.
Normal range
The engine has reached its operating tempera
ture once the LEDs up to the center of the gauge
turn on under normal driving conditions . The
LEDs higher up may turn on if the engine is under
heavy load or the outside temperature is high.
This is no cause for concern as long as the. in
dicator light in the instrument cluster does not
turn on.
12
Hot range
If the LEDs in the upper area of the display and
the . indicator light in the instrument cluster
display turn on, the coolant temperature is too
high
c:> page 19 .
A WARNING
-Never open the hood if you can see or hear
steam or coolant escaping from the engine
compartment. This increases the risk of
burns. Wait until you no longer see or hear
steam or coolant escaping.
- The engine compartment in any vehicle can
be a dangerous area . Stop the engine and al
low it to cool before working in the engine
compartment. Always follow the informa
tion found in ¢
page 198, Working in the
engine compartment.
(D Note
- In vehicles with a boost pressure indicator* ,
this indicator replaces the temperature dis
play. To promote a long engine service life,
avoiding high engine speeds, full accelera
tion and heavy engine loads during approxi
mately the first 15 minutes when the en
gine is cold is recommended . The amount of
time until the engine is warm depends on
the outside temperature . Check the engine
oil temperature* if necessary .
c:> page 30
-Auxiliary headlights and other accessories in
front of the cooling-air intake impair the
cooling effect of the coolant. This increases
the risk of the engine overheating during
high outside temperatures and heavy engine
load.
- The front spoiler also helps to distribute
cooling air correctly while driving. If the
spoiler is damaged, the cooling effect will
be impaired and the risk of the engine over
heating will increase. See an authorized
Audi dealer or authorized Audi Service Fa
cility for assistance.

Instruments and indicator lights
Drive to your authorized Audi dea le r or a uthor
ized Audi Service Facility immediate ly to have the
malfunct ion corrected
¢ .&. .
1111 (USA m od els) /. (C an ada mod els) Park
ing brake sy stem f ault! See owner' s manual
- If the indicato r light and the message appear
wh en th e vehi cle is stationar y or aft er swit ch
ing the ignit ion on ,
check if you can release the
parking b rake . If you cannot re lease the parking
brake, see your authorized A udi dealer or au
thorized Audi Service Facility. If you can re lease
the parking brake and the message st ill ap
pears, see an authori zed Audi dealer or author
ized Audi Serv ice Facility immediately to have
the malfunct ion corrected .
- If the indica tor light and message appear
whil e
driving ,
the hill start assist or emergency brak
i ng function may be malfunct ion ing . It may not
be possib le to set the pa rking brake o r release
i t once it has been set. Do not pa rk your ve hicle
o n hill s and see an authorized Audi dea ler or
authorized Audi Service Fac ility for assistance .
If the
1111 and El warning lights turn on to
gethe r, take you r veh icle to a n author ized Audi
dealer o r autho rized Aud i Service Faci lity immedi
ately to have the b rake pads inspected
¢ page 21 .
There is a lso a war ning tone when the lights t urn
on .
_& WARNING
- Read and fo llow ing the warn ings in
¢ page 198, Working in the engine com
partment
before opening the hood and
check ing the brake fluid level.
- If the brake system indicator light does not
turn off or it turns on wh ile driving, the
brake flu id leve l in the reservo ir is too low,
and this increases the r isk of an accident.
Stop the vehicle and do not continue dr iv
ing . See an author ized Audi dealer or au
tho rized Aud i Service Fac ility for assistance.
- If the brake system indicator light tu rns on
together with the ABS and ESC ind icator
lights, the ABS/ ESC regu lating fu nction may
be malfunctioning. Functions th at stabilize
18
the vehicle are no longer ava ilable . This
could cause the rear of the vehicle to
swerve, which increases the r isk that the ve
hicle will slide. Drive carefully to the nearest
author ized Audi dealer or authorized Audi
Service Fac ility and have the malfunction
corrected.
PARK/(®)/ ~ Electromechanical parking
brake
If the -(U SA mode ls) /. (Canada mode ls)
indicato r light turns on, t he parking brake was
set.
- (USA model s) / . (Canad a model s) Cau
tion: Vehicle parked too steep
If the indicato r ligh t blink s and the message ap
pe ars, there is no t eno ugh braking powe r to se
cu re the vehicle. The brakes have overheated. The
vehicle could ro ll away even on a sma ll incline.
- (USA mod els ) /. (Canada model s)
Plea se pr ess brak e pedal t o rel ease parking
br ake
To re lease the park ing brake, press the brake ped
al and p ress the~ button at the same time, o r
star t driving with hill start assist
¢page 80,
Starting from a stop.
Ill Parking brak e!
There is a malfunc tion in the parking brake. Drive
to an authorized Aud i dea ler or authorized Audi
Service Facility immed iately to have the malfunc
tion co rrected .
Ill Parking brake: limited functionality !
There is a malfunction in the parking brake. Drive
to an authorized Audi dea ler or a uthori zed Audi
Service Facility immed iate ly to have the ma lfunc
tion correc ted.
!~;1 ;1J: );J;13~ ( USA models ) / ¢@'A
Release the par king brake if this message ap
pears.
lt1 ;1J :);tJ :H ( USA m odels ) / iiJ (Canada models)
Parking brake aut o release unavailable
...

Opening and closing
only the driver 's door or the entire vehicle should
un lock when unlocking
q page 3 7 .
Automatic locking (Auto L ock )
The Auto Lock funct ion loc ks all doors and the
luggage compartmen t lid once the speed has ex
ceeded approximate ly 9 mph (15 km/h).
The ca r is unlocked aga in once the ignition key is
removed . In add ition, the vehicle can be unlo cked
if the opening function in the power locki ng sys
tem sw itch is used or one o f the door handles is
pu lled .*
Add it io nally, in the event of a cr ash with a irbag
dep loymen t the doors are au tom atic ally un
lo cked to allow access to the vehicle.
Anti-theft alarm system*
If th e a nti-theft alarm system detects a ve hicle
break-in, audio and v is u a l warning s ignals are
tr iggered.
The ant i-theft alarm system tu rns on automati
cally when you lock the veh icle. It deact ivates
wh en unlocking usi ng the remote cont ro l key or
by to uchin g the se nsor on the door handle ( con
ven ience key).
To switch the a larm off, press th em butto n on
the r emote co ntro l key or convenience key or
sw itch the igni tion on. The alarm a lso stops au to
ma tica lly aft er a cer ta in amoun t of time.
Turn signals
W hen you unlock the vehicle, the t urn signa ls
flash twice . W hen you lock the vehicle, the t urn
signals flash once.
If they do not flash, one of the doo rs, the lug
gage compartment lid or the hood is not loc ked
or the ignition is still sw itched on (the la tter ap
plies to veh icles with a convenience key).
Unintentionally locking yourself out
In the following cases there safeguards to pre
ve nt you lock ing you r remote master key in the
ve hicle:
- The vehicle does not lock with the centra l lock
ing switch if the driver's door is open
c> page 37 .
34
-On veh icles with a convenience key*, the l ug
gage compa rtment lid unlocks again after clos
ing if the most recently used key is in the lug
gage compa rtment.
Do not loc k your vehicle w ith the remote control
key or convenience key * until all doors and the
l uggage compartment lid a re closed. In this way
you avoid locking yourse lf out accidentally .
@ Tips
-Do not leave va luab les unattende d in the ve
hicle. A locked veh icle is not a safe!
- If the LE D in the u pper edge of the drive r's
doo r tu rns o n for a bout 30 seconds after
the vehicle is locked, there is a ma lf u nction
in the power locki ng or the anti-theft alarm
system*. Have the problem corrected by an
autho rized Aud i dealer or autho rized Audi
Service Facility .
LED and batterie s in the remote control key
Fi g. 19 Remote con trol key: LED
Fig. 20 Remote con trol key: open ing the cove r
LED in the remote control key
The LED c> fig. 19 can tell you about the fu nction
of the remote control key. ..,_

....,
N
0 > co
rl I.O
"'
"'
"'
rl
-You should not drive your vehicle or press
the windshie ld wiper lever when the wiper
arms are folded away from the w indshield.
The windshield wipers would move back in
to their original position and could damage
the hood and windshield .
- To prevent damage to the windshield wash
er system, a lways loosen wiper blades that
have frozen to the windsh ield before turn
i ng the wipers on .
- To prevent damage to the wiper blades, do
not apply gasoline, petro leum, th inning
agents or other solvents on the wiper b lades or near them.
- To prevent damage to the wiper arms or
othe r components, do not try to move the
windsh ield wipers by hand.
@ Tips
- Commerc ial hot wax such as the types used
by car washe s make it more difficult t o clean
the w indshie ld.
- You can also use the service pos ition, for ex
ample, if you want to p rotect the w indshie ld
from i cing by us ing a cover.
- You cannot activate the service pos it ion
whe n the hood is open.
Digital compass
Switching the compass on and off
Ap plies to vehicles: w ith digi tal compass
Fig. 4 2 Rearview mirro r: Dig ital compass act ivated
... To turn the compass on or off, press the button
@ until the compass in the mirror appears or
disappears.
Light and Visio n
The dig ita l compass on ly works when the ignit ion
is turned on . The directions a re indicated with ab
breviations:
N (nort h), NE (northeast), E (east),
SE (southeast), S (south), SW (southwest), W
(west), NW (northwest).
You must recalibrate t he compass if it does not
display the correct direct ion
¢ page 52, Cali
brating the compass.
(D Tips
To prevent inaccurate compass readings, do not br ing any remote controls, electrical devi
ces or metallic objects near the mirror.
Adjusting the magnetic zone
Appl ies to vehicles: wit h digita l co mp ass
The magnetic zone must be adjusted correctly
for the compass to read accurately.
®
Fig. 4 3 Nor th Ameri ca: magnet ic zone map
... Press and hold the button @ ¢page 51, fig . 42
until the number of the mag netic zone appears
in the rearview mirror .
... Press the butt on @ repeatedly to select the
correct magnetic zone. The se lection mode
tur ns off after a few seconds .
51

....,
N
0 > co
rl I.O
"'
"'
"'
rl
-Never select R or P while driving, because
this increases the risk of an accident.
- Power is stil l transmitted to the whee ls
when the engine is running at idle. To pre
vent the vehicle from "creeping", you must
keep your foot on the brake in all selector
lever positions (except P) when the engine is
running . Otherwise, this inc reases the r isk
of an accident.
- Do not inadvertently press the accelerator
peda l when the veh icle is stopped if a gear is
engaged . Otherwise the vehicle will start to
move immediately, even if the pa rking brake
is set . This could res ult in a crash.
- Do not press the accelerator pedal when
changing the selector lever pos ition while
the vehicle is stationary and the engine is running.
- Never leave your vehicle with the eng ine
running whi le in gear . If you must leave your
vehicle when the engine is running, set the parking brake and move the selector lever to
the P position.
- Before opening the hood and working on a
running engine, select the P position with
the se lector lever and activate the parking
brake. Always read and fo llow the applicable
warnings
¢ page 198, Working in the en
gine compartment.
(D Note
Never let the veh icle roll downhill with engine
off and the selector lever in the N pos ition,
because this could damage the automatic
transmiss ion and catalyt ic converte r.
(D Tips
- Audi drive select: Sporty shifting character
i stics can be selected us ing the
Dynam ic
driving mode.Sw ill appear in the instru
ment clust er disp lay ins tead of D.
- If you accidentally select N while driv ing,
take your foot off the acce le rator pedal im
mediately and wa it for the engine to slow
down to idle before select ing Dor S .
-If there is a power failure, the se lector lever
will not move out of the P posit ion. The
Au tom atic t ra nsm iss io n
emergency release can be used if this hap
pens
¢page 89.
Selector lever lock
Applies to veh icles: w ith S tronic tra nsm iss io n
The selector lever lock prevents you from select
ing o gear occidentally, causing the vehicle to
roll.
Fig. 73 Selecto r lever lock
To release the selector lever lock:
.,. Switch on the ignition.
•
m 0
0
>
~
.,. Press the brake pedal while pressing the inter-
lock button.
Automat ic shift loc k (AS L)
The selector lever is locked in the P and N posi
tions when the ignition is switched on. You must press the brake peda l to select another position .
You must also press the interlock button if you
are moving from the P pos ition . The fol low ing
message appears in the d isplay when the selector
lever is in the P or N posit ion to remind the dr iv
er:
When stationar y appl y footbrake whil e selec t
ing g ear
The automatic sh ift lock only functions when the
vehicle is stat ionary or at speeds below 1 mph
(2 km/h). At h igher speeds, the lock is automati
cally deactivated in the N pos ition .
The selector lever is not locked when shift ing
quickly through N, for example from R to D. This
makes it poss ible to free the vehicle when it is
stuck by "rock ing" it . The selector lever lock en-
gages if the leve r stays in the N pos ition longer
liJ,,
83

Automatic transmission
-If the engine must run while you are work
ing in the engine compartment with the
hood open, make sure a gear is not engag
ed . The selector lever must be firmly in the
P position and locked in place and the park
ing brake must be set ¢
page 198. Other
wise, the vehicle could begin moving when
the engine speed is high, even with the
parking brake set.
0 Note
- When stopping on an incline, do not try to
hold the vehicle in place by pressing the ac
celerator pedal while a driving gear is se
lected. This can cause the automatic trans
mission to overheat and can damage it. Ac
tivate the parking brake or press the brake
pedal to prevent the vehicle from rolling.
- Allowing the vehicle to roll when the engine
is stopped and the selector lever is in the N
position will damage the automatic trans
mission because it is not lubricated under
those circumstances.
- The transmission can overheat and be dam
aged under certain driving and traffic condi
tions such as frequent starts, creeping for a
long time, or stop-and-go traffic . When the
5] or. indicator light turns on, stop the
vehicle at the next opportunity and let the
transmission cool¢
page 88.
-Allowing the vehicle to roll when the engine
is stopped will damage the S tronic trans
mission because it is not lubricated
¢ page 2 54, Towing with a tow truck.
(D Tips
For safety reasons, the parking brake only re
leases automatically when the driver's door is
closed.
Hill descent control
Applies to veh icles: w ith S tron ic transm ission
The hill descent control system assists the driv
ing when driving down declines.
Hill descent control is activated when the selec
tor lever is in the Dor S position and you press
86
the brake pedal. The transmission automatically
selects a gear that is suitable for the incline. Hill
descent control tries to maintain the speed ach
ieved at the time of braking, within physical and
technical limitations. If may still be necessary to
adjust the speed with the brakes. Because hill de
scent control cannot shift down farther than 3rd
gear, it may be necessary to shift into tiptronic
mode in very steep areas . In this case, shift into
1st or 2nd gear in tiptronic mode to use the en
gine's braking force to relieve the brakes.
Hill descent control switches off once the decline
levels out or you press the accelerator pedal.
On vehicles with a cruise control system*
¢
page 94, hill descent control is also activated
when the speed is set .
&_ WARNING
Hill descent control cannot overcome physical
limitations, so it may not be able to maintain
a constant speed under all conditions. Always
be ready to apply the brakes.

Checking and F ill in g
damp cloth and plenty of cold water. If the
AdB lue has already crysta llized, use warm
water and a sponge. AdBl ue res idue that is
not removed will crysta lli ze and can damage
the affected s urface.
- Do not store the ref ill bottle in the vehicle.
If it leaks, the escaping Ad Blue cou ld dam
age the veh icle inter ior.
- Do not allow Ad Blue to come into contact
with clothing. If there is contact with the
flu id, flush immed iate ly w ith plenty of wa
ter .
@ Tips
-You can obtain refill bott les from an author
i zed Audi dealer or authorized Audi Service
Facility .
- Follow the Ad Blue manufacturer 's instruc
tions for use and storage .
Engine compartment
Working in the engine compartment
Special care is required if you are working in the
engine compartment
For work in the engine compartment such as
c h ecking and filling fluid s, there i s a risk of in
jury, scalding , accid ents, and burns. F or thi s
rea son, follow all the following li sted warning s
and general safety precautions. The engine
c ompartment is a dangerous area!
~ &
A WARNING
To reduce the risk of injur ies, complete the
following steps before opening the hood :
- Turn the eng ine off.
- switch the ignit ion off .
- Set the parking b rake.
- Pla ce the sele ctor leve r in the P pos ition.
- Let the engine coo l down .
- Never open the hood when you see that
steam o r coolan t drips from the engine
compartment- there is a da nger of burns!
Wait un til no steam o r coolant flows ou t.
- Keep children away from the engine com
partm ent.
198
-
- Never sp ill fluids on a hot engine . These fl u
ids (such as the freeze protection conta ined
in the coolant) can catch fire.
- Avoid short circ uits in the e lectrica l system,
especially the battery.
- When working in the engine compa rtment,
remember that the radiator fan can switch
on even if the ignition is switched off, wh ich
increases the risk of pe rsonal injury.
- Never open the cap on the coolant expan
si on tank when the engine is warm . The
cooli ng system is under p ress ure .
- To protect yo ur face, hands, and a rms from
hot steam or coolant, cover the cap with a large cloth when o pening.
- Do not remove the engine c over under any
circumstances . T his i ncreases the r isk of
burns.
- If tests need to be per formed with t he en
gine running, there is additional danger due
to mov ing components (such as the rib bed
be lt , a lternator a nd radiator fan) a nd from
the high v olt age ignit io n sy stem.
-Never reac h into the radiato r fan . The e lec
tric aux iliar y fan i s controlled by tempera
ture and can swi tch on sudden ly.
- Pay attention to t he fo llow ing warnings list
ed when w ork on the fue l system o r on the
elec tric al equipmen t is requ ired .
- Always d isconnect the vehicle battery
from the vehicle electrical system
- Do not smo ke
- Never work near open flames
- Always have a work ing fire exting uis her
near by
- To reduce t he risk of e le ct ric shock and in
jury, never touch the following components
when t he engine is running or is bein g start
e d :
- Ign ition cable
- Other components in the electronic h igh
vo ltage ignition system
- If you must check or perform work o n the
e ngine whi le it is running:
- S et t he parki ng bra ke and pla ce the selec
t or lever in the P (park) posi tion first .

....,
N
0 > co
rl I.O
"'
"'
"'
rl
-Always proceed with extreme caution so
that clothing, jewelry or long hair do not
become caught in the radia tor fan, fan
belt or other moving components or do not come into contact with hot compo
nents . T ie back long hair before beg inning
work and do no t wear cloth ing that can
hang down into the eng ine.
- limit your exposure to exhaust and chemi
cals to as short a time as possible
q ,& .
..&, WARNING
California Propos ition 65 Warning:
- Engine exhaust, some of its constituents,
and certai n veh icle components conta in or
em it chemicals known to the State of Cali
forn ia to cause cancer and birth defec ts and
reproductive harm. In addition, certai n flu
ids contained in vehicles and certain prod
ucts of component wear contain or emit
chemicals known to the State of California
t o cause cancer and birth defects or other
reproductive harm .
- Battery posts , terminals and related acces
sories contain lead and lead compounds,
chem icals known to the State of California
to cause cancer and reproductive harms .
Wash hands after hand ling.
(D Note
When filli ng flu ids, be sure not to m ix the flu
ids up . Otherwise seve re malfunctions and en
gine damage w ill occur .
@ For the sake of the environment
You should regu larly check the grou nd under
your veh icle in order to detect leaks quickly . If
there are visible spots from oil or other f luids,
b ring yo ur vehicle to an autho rized Aud i dea l
er or authori zed Audi Se rv ice F acili ty to be
checked.
Ch eck in g and Fillin g
Opening the hood
The hood is released from the in terior .
Fig . 155 Se ctio n from t he dr iver' s footwe ll: re le a se le ve r
Fig . 156 Ro cke r swit c h un der t he hoo d
Make sure the wiper arms a re not raised up from
the windsh ie ld . Oth erwise the paint cou ld be
damaged.
.,. W ith the driver's door open, pull the lever be
low the instr ument pane l in the d irect ion of the
arrow
<=> fig. 155.
.,. Raise the hood slightly r:!> ff::.. .
.,. Press the rocker switch unde r the hood upward
q fig. 156 . This re leases the catch .
.,. Open the hood .
..&, WARNING
-=
Never open the hood when you see that steam
or coolant drips from the engine compart
ment- there is a da nger of bu rns! Wait unt il
n o steam or coolant flows out .
- Never open the hood when you see that
s team or coo lant dr ips from the e ngine
comp artment- the re is a dange r of burns !
Wait until no steam or coo lant flows o ut .
199