2015 AUDI RS7 SPORTBACK lights

26 Instruments and warning/indicator lights
Lower odometer
The lower odometer shows the total number
of miles (kilometers) driven.
Malfunction message
If there is a malfunction in the instrument
cluster,
DEF will appear in the trip odometer
display area. Contact your authorized Audi
dealer to have the problem corrected.
Time and date display
Fig. 12 Instrument cluster : cloc k and date
You can set the time and the date display in
the MMI. Refer to the MMI owner's manual
for instructions .
When you open the driver's door, the date and
time appear in the instrument cluster display
for 30 seconds.
Service interval display
The service interval display reminds you when
your next service is due.
Fig. 13 In strum ent cluste r: Serv ic e inte rval d isp lay
The schedule for the next oil change or inspec­
tion is calculated automatically and displayed
accordingly. The display works in two stages :
Service reminder
30 days before the next service is due, a serv­
ice reminder appears in the display when you
switch the ignition on
¢ fig. 13.
After about 5 seconds the display switches
back to normal. The distance and time re­
maining are updated each time the ignition is
switched on until the date due for service is
reached.
Service due
When the due date for service is reached, the
message
Service due! appears in the instru­
ment cluster immediately after you switch the
ignition on. Additionally, a warning tone
sounds. After about 5 seconds the display
switches back to normal.
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the MMI display by selecting
the service interval display in the car menu.
Select the
ICARI function button > (Car)* sys­
tems control button > Servicing & checks >
Service interval displays .
Resetting the service interval display
Your authorized Audi dealer w ill reset the cor­
responding service schedule after performing
the appropriate service on your vehicle. You
also have the possibility to reset the oil
change schedule after having performed an
oil change according to Audi specifications .
Select the
ICARI function button > (Car)* sys­
tems control button > Servicing & checks >
Service Intervals> Reset oil change interval.
Q) Note
-Only reset the oil change display when
you have completed an oil change.
- If you disconnect the battery terminals,
no calculations can be made for the serv­
ice interval display during this time and
no service reminder will appear. Remem­
ber that observing the proper service in­
tervals is vitally important to extending
the life of your vehicle, particularly the
ll>-

Instruments and warning/indicator lights 2 7
engine, and maintaining its value. Even if
the mileage driven is low, the maximum
period of one year from one service to
the next must not be exceeded.
(D Tips
The information in the Service Remi nder
remains stored even when the vehicle bat­
tery is disconnected.
Head-up Display
Applies to vehicles: with Head-up Display
Fig. 14 Example: indicators in the Head-up Display
Fig. 15 Instrument panel: knob for the Head-up Dis ·
play
The Head-up Display projects certain warnings
or selected information from the assistance
systems* or navigation* on the windshield.
The display appears within the driver's field of
v1s1on.
Switching on/off
.,. Press the knob~ to switch the Head-up
Display on/off¢
fig. 15.
Adjusting the height
"' N a:: The height of the display can be adjusted to I.J "". the individual driver. rl I.O
"' rl
"' rl
.,. Make sure you are seated correctly
¢page 121 .
.,. Turn the knob ~ to adjust the display.
Settings in the MMI
.,. Select: !CAR ! function button> (Car)* sys­
tems
control button > Driver Assist > Head­
up Display
> Head-up Display content or
Display brightness.
Display content
In the MMI, you can specify which information
should be displayed:
- Cruise control system*
- Navigation information*
- Audi adaptive cruise control*
- Audi active lane assist*
- Night vision assistant*
The speed display and some of the red indica­
tor lights cannot be hidden in the MMI.
Display brightness
You can adjust the display brightness in the
MMI. The display brightness decreases auto­
matically as the amount of light decreases.
The basic level of brightness is adjusted with
the instrument illumination¢
page 47.
(D Note
To prevent scratches on the glass covering
the Head-up Display, do not place any ob­
jects in the projection opening.
(D Tips
-Sunglasses with polarization filters and
unfavorable lighting conditions can af­
fect the display.
- A special windshield is needed for the
Head-up Display function.
- For information on cleaning, refer to
¢ table on page 203.

28 Instruments and warning/indicator lights
Boost, shifting and engine oil
temperature indicators
Fig. 16 Instrument duster : boost, shift ing a nd engine
o il t emp erature indicato rs
• Turn the menu thumbwheel on the steering
wheel until
Lap timer appears in the instru­
ment cluster display .
@ Boost pressure indicator
The current engine load (meaning the current
boost pressure) is indicated by a bar .
@ Shifting indicator
The shifting indicator is only visible when
shifting gears with the selector lever in tip­
tronic mode¢
page 107. Green LEDs turn on
as the engine RPMs increase. The L EDS flash
red at speeds near the RPM lim it.
I n vehicles with an activated head-up display
¢ page 2 7, the shifting indicator is shown in
the head-up disp lay instead of the instrument
cluster.
© Engine oil temperature indicator
If the engine oil temperature is below 140 °F
(60 °(), the l!I symbo l followed by three hy­
phens "- - -" and the °C un it is shown .
The engine has reached its operating temper ­
ature when the engine o il temperature is be­
tween 140
°F (60 °() and 248 °F (120 °() un­
der normal d riving conditions. The engine oil
temperature may be higher if there is heavy
engine load and high temperatures outside.
This is not a cause for concern as long as the
• ¢page 16 or II ¢page 17 warning light
in the display does not flash.
Lap timer
Introduction
You can record and evaluate lap times with
the lap timer in the disp lay ¢
page 28,
fig. 17. The time is measured in minutes, sec­
onds and 1/10 seconds. The hours are also
shown when the lap time exceeds 60 minutes .
The maximum individual measurement is 99
hours.
A maximum of SO laps may be record­
ed.
A WARNING
-Please devote your full attention to driv -
in g. As the driver, you have complete re­
sponsib ility for safety in traff ic. Only use
the functions in such a way t hat you a lways
maintain complete control over your vehi­
cle in all traffic situations .
(i) Tips
When the lap timer stopwatch is running,
you can call up the on-board computer in­
formation.
Calling up the lap timer and timing
Fig . 17 D isplay: Lap t imer
Calling up the lap timer
• Turn the thumbwheel until the lap timer ap-
pears.
Timing laps
• To start timing, press the thumbwheel.
• To stop timing for this lap, press the thumb­
wheel again . This also starts timing the next
round. The previous timing always moves
one line up . The lap number that
II>

"' N
a:: I.J "". rl I.O
"' rl
"' rl
Instrument s and warning /indicator lights 29
corresponds to the timing is displayed in
front of the ind ividual timings .
Displaying intermediate time and pausing
timing
.. To disp lay an intermediate time, press the
t h umbwheel. The timing cont in ues to run in
t h e background .
.. To pa use tim ing, press the thumbwhee l.
.. To continue t iming, press the thumbwheel
again.
If t iming is paused, you can continue it later
even if you switch the ignit ion
off.
Evaluating times and continuing or
resetting timing
You can evaluate the fastest, slowest and
average lap times.
F ig. 1 8 Dis pl ay: lap t ime eva luat ion
.. To ev aluate lap t imes, press the t humb­
whee l. The number of laps traveled, the
f astest lap"+", the slowes t lap" -" and the
average lap time "0" appears in the disp lay .
.. To continue t iming for addit iona l laps, press
t h e thumbwheel.
.,. To reset the timer to ze ro , press the thumb­
whee l aga in . The lap t imer is switched
off
now.
(D Tips
- Saved lap t imes cannot be ind iv idually
dele ted from t he tota l resu lts .
- The saved lap timer values will not be
l ost after turn ing the ig nitio n
off.
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL )
The Ma lfunction Indicator Lamp ( MIL) ¢'4 in
the instr ument cluster is part of the On-Board
Diagnostic (OBD II) system .
T he wa rni ng/indicator light ill uminates when
the ignit io n is switched on and goes out after
the engine sta rts and the id le has stab ilized.
This indicates that the M IL is working proper­
ly .
If the light does not go out afte r th e engine
is started, or illuminates while you are dr iv­
ing, a mal function may exist in the engine sys ­
tem .
If the light illum inates, the catalyt ic con­
verter could be damaged .
Contin ue driving
with reduced power (avoid­
ing s ustained high speeds and/or rapid accel­
erations) and have the cond ition corrected.
Contact your aut horized Audi dea ler.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
¢ page 208.
On-Board Diagnostics
Fig. 19 Locat io n of Data Li nk Co nnector (D LC)
On-Board Diagnostics monitors the compo ­
nents of your emission contro l system. Each
monitored component in your engine system
has been ass igned a code. In case of a mal­
funct ion , the component will be identified
and the fault stored as a code in the control module memo ry.

30 Instruments and warning /indicator lights
The MIL light may a lso illuminate if there is a
leak in the on-board fue l vapor recovery sys­
tem .
If the light illuminates after a refuell ing,
stop the vehicle and make sure the fuel filler
cap is properly closed¢
page 208.
In order to make an accurate diagnosis, the
stored data can only be displayed using spe­
cial diagnostic equipment (generic scan tool
for OBD) .
In order to connect the special diagnostic
equipment, push the p lug into the Data L ink
Connector (DLC). The DLC is located to the
rig ht of the hood release ¢
fig. 19.
Your authorized Audi dealer or a qualified
service station can interpret the code and per­
form the necessary repair .
A WARNING
Do not use the diagnostic connector for
personal use . Incorrect usage can cause
malfunctions, which can increase the risk
of a coll ision!
-

44 Clear vis ion
Clear vision
Lights
Switching the headlights on and off
Fig . 39 Instr ument pane l: light sw itch w it h all -weath­
er lig hts
The headlights only wo rk when the ignition is
sw itched on. Wh ile start ing the eng ine or
when switching off the ig nition, the head­
lights will go off and on ly the s ide marker
lights w ill be on .
I f the sys tem is not operating properly, a
warn ing symbol in the dr iver inform ation dis­
p lay is dis played ¢
page 21.
Light switch -~ -
Turn the switch ¢ fig. 39 to the co rrespond ing
position . When the lights a re switched o n, the
:oo: symbo l turns on.
0 -The lights are off or the dayt ime run ning
lights are on:
- USA models: The daytime running lig hts
will come on automatically when the igni­
t ion is on and the light switch¢
fig. 39 is in
the
O pos it ion or the AUTO position (only in
daylight cond itions). The
Daytime running
lights function can be tu rned on and off in
the MMI ¢
page 45, ¢ .& .
-Canada model s: T he daytime running lig hts
will come on au tom atically when t he igni ­
t ion is on and the light switch¢
fig. 39 is in
the
O posit io n, the :oo~ position or the AUTO
posit ion (on ly in daylight conditions)¢ .&.
AUTO -Automatic headlights swi tch on an d
off depend ing o n brightness, fo r example in
tw ilight, during rain or in tunnels¢.&.
:oo~ -Side marker lights
io -Low beam head lights
~ -All-weather lig hts
@!l -Rear fog lights *. When the rear fog lights
are on, the symbol
0$ on the sw itch will i llu­
minate.
All-weather light s
In vehicles with all -weather lights, the front
lights are ad justed automatically so that you
are less like ly to see glare from your own
headlig hts, for example when driving on a wet
road .
Automatic headlight range cont rol*
T he headlights do not blind oncoming traffic
if the veh icle load changes . The head light
range also ad justs automatica lly when brak­
ing and accelerating .
Light functions
The following light funct ions are availab le de­
pending on vehicle equipment and o nly func ­
tion when the lig ht switch is i n the AUTO posi ­
t ion. You can deactivate these functions in the
MMI u nder
Audi adapt ive light *¢ page 45.
Vehicles with Static corneri ng light*: the cor­
nering light switches on a utomatica lly when
the steering whee l is turned at a certa in angle
at speeds up to app rox imately 44 mph
(70 km/h) and when the turn signal is activat­
ed at speeds up to app rox imately 25 mph
(40 km/h) . Th e ar ea to the side of th e vehicle
is illum inated better when turn ing .
Vehicles with
Dynamic curve light*: the curve
light only functions at speeds betwee n ap­
proximate ly 6 mph (10 km/h) and 68 mph
(110 km/ h) and adapts itse lf to the cu rves in
the road.
A WARNING
- Automatic headlights are o nly inte nded
t o assist the driver. They do not relieve
the dr iver of his respons ibility to check
the head lights and to turn them on ma n-
ually accord ing to the current light and ,..

"' N
a:: I.J "". rl I.O
"' rl
"' rl
visibility conditions. For example, fog cannot be detected by the light sensors.
So always switch on the headlights 1§.D under these weather conditions and
when driving in the dark.
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists . Always turn on
the headlights so that you can see ahead
and so that others can see your car from
the back.
- Please observe legal regulations when
using the light ing systems descr ibed .
(D Note
The rear fog lights should only be turned
on in accordance with traffic regulation, as
the lights are bright for following traffic.
@ Tips
- The light sensor* for automatic head­ light range control* is located in the rear
view mirror mount. You should therefore not apply any stickers to the windshield
in this area in order to prevent malfunc­
tions or failures.
- In the event of a light sensor malfunc­
tion, the driver is notified in the instru­
ment cluster display ¢
page 21.
-You will hear a warning tone if you open
the driver door when the exterior lights
are switched on .
- In cool or damp weather, the inside of
the headlights, turn signals and tail
lights can fog over due to the tempera­
ture difference between the inside and
outside. They will clear shortly after
switching them on. This does not affect
the service life of the lighting .
Clear vision 45
Emergency flasher
The emergency flasher makes other motorists
aware that you or your vehicle are in an emer­
gency situation .
Fig. 40 Ce nt er co nsol e: em erge ncy flash er sw itc h
.,. Press the switch &..¢ fig. 40 to turn the
emergency flashers on or off.
When the emergency flasher is on, all four
turn signals blink at the same time . The turn
signal indicator lights
B DI in the instru­
ment cluster, as well as the light in the emer­
gency flasher switch &.. blink likewise. The
emergency flashers also work when the igni­
tion is turned off.
The emergency flashers will turn on automati­
cally if you are in an accident where the airbag has deployed.
@ Tips
You should turn on the emergency flashers
when:
- you a re the last vehicle standing in a traf­
fic jam so that any other vehicles coming
can see you, or when
- your vehicle has broken down or you are
in an emergency situation, or when
- your vehicle is being towed by a tow
truck or if you are towing another vehicle
behind you.
Adjusting the exterior lighting
The settings are adjusted in the MMI.
.,. Select: !CAR ! function button> (Car)* sys­
tem s
control button > Vehicle settings > Ex-
terior lighting. ..,.

46 Clear vision
Automatic headlights
You can adjust the following settings in the
Automatic headlights menu:
Headlights a ctivation time -You can adjust if
the head lights switch on Early, Med. or Late
according to the sensitivity of the light sensor.
Audi adaptive light* -You can sw itch adaptive
light On and Off.
Daytime running lights
USA models : You can switc h the dayt ime run­
ning lights on and off.
Canada models: The function cannot be
turned off . It is activated automatica lly each
time the ign ition is switched on. This menu
item is shown "greyed out".
Coming home, Leaving home
The coming home function illuminates the
area outside the vehicle when yo u switch the
ignition off and open the driver's door. To turn
the function on, select Lights when leaving
car> On .
The leaving home function illuminates the
area outside the vehicle when you un lock the
vehicle. To turn the funct ion on, select Lights
when unlocking car > On .
The coming home and leaving home functions
only operate when it is dark and the light
switch is in the AUTO position. Turn signals and high beam lever
The lever on the left side of the steering col­
umn is used to operate the turn signals and
the high beam as well as the headlight flash­
er.
Fig. 41 Turn signal and high beam lever
The turn signa l and hig h beam lever has the
following functions:
Turn signals ¢
9 (D@
.. Push the lever up as far as it can go to turn
on the right turn signal or down to turn on
t he left turn signal ¢
fig. 41.
N 0 ... 'i' :r
~
.. Move the lever briefly unti l you meet res ist­
ance and re lease it to flash three times.
.. Move the lever (up or down) until you meet
resistance and hold it there to determine
the flashing time for the turn signals.
High beam
[D @
.. Push the lever forward to switch on the high
beam.
.. Pull the lever back towards yo u to switch off
the high beam.
Headlight flasher
[D ©
.. Pull the lever toward the steering whee l to
use the headlight flasher.
Notes on these features
- The
turn signals only work w ith the ignition
switched on. The indicato r lights
B or B
in th e instrument cluster¢ page 11 also
blink.
- After you have turned a corner, the turn sig­
na l switches off automatically.
- The
high beam works only when the head-
lights are on. The indicator light
El in the ..,.