266 What do I do now?
Position the vehicle jack only under the desig
nated lifting points on the sill
r::!;> fig. 210.
There is exactly one location for each wheel.
The jack must not be positioned at any other location¢ ,&.¢(D .
An
un stable surfa ce under the jack can cause
the vehicle to slip off the jack. Always prov ide
a firm base for the jack on the ground. If nec
essary place a sturdy board or similar support
under the jack . On
hard, slippery surfaces
(such as tiles) use a rubber mat or sim ilar to
prevent the jack from slipping¢.&..
A WARNING
-You or your passengers could be injured
wh ile chang ing a wheel if you do not fol
low these safety precautions:
- Position the vehicle jack only at the
designated lifting points and align the
jack . Otherwise, the vehicle jack could
slip and cause an injury if it does not
have sufficient hold on the vehicle.
-A soft or unstable surface under the
jack may cause the veh icle to slip off
the jack. Always provide a firm base for
the jack on the ground.
If necessary,
use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or sim ilar to prevent
the jack from s lipping.
- T o help prevent injury to yourself and
yo ur passenge rs:
- Do not raise the vehicle unti l you are
sure the jack is securely engaged.
- Passengers must not remain in the ve
hicle when it is jacked up.
- Make sure that passengers wait in a
safe p lace away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad
just as necessary and then continue to ra ise the jack.
- Changes in temperature or load can af
fect the height of the vehicle.
(D Note
Do not lift the vehicle by the sill. Position
the veh icle jack only at the designated lift
ing points on the sill. Otherwise, your vehi
cle will be damaged.
(D Tips
The vehicle jack mode * switches off auto
matically at speeds above 6 mph (10 km/
h).
Removing and installing the sill cover
Applies to vehicles: with sill
Fig. 212 Sill: remov ing the cover
.. Pull the cover down to remove it¢ fig. 212.
.. To install the cover again, insert it into the
retainers and then swing it upward until it
clicks into place. The cover must be flush
with the sill.
@ Tips
Some models may also have a cover for the
rear vehicle lift point.
Taking the wheel off/installing a wheel
Follow these instructions step-by-step for
changing the wheel.
Fig. 213 Changing a wheel: using the screwdriver han
dle (with the blade removed) to turn the bo lts
F ig . 214 Changing a wheel: alignment pin ins ide the
top hole
After you have loosened a ll wheel bolts and
ra ised the veh icle off the ground, remove and
replace the wheel as follows:
R emoving the wheel
.. Use the hex agon al so ck et in th e screw driv
e r handle
to comp letely remove the top
most wheel bo lt and set it aside on a
clean
s u rface ¢fig. 213.
.. Screw the threaded end of the alignm ent
pin from the tool k it hand -tight into the
empty bolt hole¢
fig. 214.
.. Then remove the other wheel bo lts as de
scribed above .
.. Take off the wheel leaving the alignment pin
in the bolt hole ¢(D .
Putting on the oth er w heel
"' .. Lift the wheel and carefully slide it over the N
a:: alignment pin to guide it in place ¢(D. I.J -
"' rl
"' rl
What do I d o now ? 267
.. Use the hexagonal socket in the screwdriver
handle to screw in and tighten all wheel
bolts
slightly.
.. Remove the alignment pin and insert and
tighten the remaining wheel bolt slightly like the rest.
.. Turn the jack handle counter-clockwise to
lower the veh icle until the jack is fully re
leased .
.. Use the wheel bo lt wrench to tighten all
wheel bo lts firm ly¢
page 264. Ti ghten
them
crosswise, from one bolt to the (ap
proximately) opposite one, to keep the
wheel centered.
(D Note
When removing or installing the whee l,
the rim could hit the brake rotor and dam
age the rotor. Work carefully and have a
second person help you.
@ Tips
Never use the hexagonal socket in the han
dle of the screwdriver to loosen or tighten
the w heel bolts.
- Pull the reversible blade from the screw
dr iver before you use the hexagonal
socket in the handle to turn the wheel
bolts.
- When mounting tires w ith
unidi rectional
tread design
make sure the tread pat
tern is po inted the right way
~page 268.
-The wheel bo lts shou ld be clean and easy
to turn. Check for dirt and corrosion on
the mating surfaces of both the wheel
and the hub. Remove all d irt from these
surfaces before remounting the whee l.
268 What do I do now?
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction .
Using a replacement tire with a tread
pattern intended for use in a specific
direction
When using a re p la cemen t tir e wi th a tread
pattern inte nded for use in a speci fic dire c
tion, please note the fo llow ing :
- T he direction of rotation is marked by a n ar
row on the side o f the tire .
-If the r eplacement tire has to b e insta lled in
t h e inc orre ct direction, use the rep la ce m ent
tir e on ly tempor arily s ince the t ire will not
be able to a chieve its op timum perfo rm ance
characteris tics with regard to aqua planing,
noise and wear .
- W e recommend that you pay particular a t
tent io n to this fact du ring wet weat her and
t h at you adjust your spee d to matc h roa d
condit ions .
- Repl ace the flat tire w ith a new one and
have it installed on your veh icle as soon as
poss ible to resto re the handling advantages
of a unid irect iona l tire .
Notes on wheel changing
Please read the information 9 pag e 245, New
tires and replacing tires and wheels
i f you are
go ing to use a rep lacemen t tire w hich is dif
feren t fro m th e tires on you r veh icle.
After you cha nge a t ire :
-Check the t ire pressure on the replacement
tire immediately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as
possible by your authorized Audi dealer or
a qualified service station .
- With steel and alloy wheel rims , the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm) .
- If you notice that the wheel bolts are cor
roded and difficult to turn while changing a tire
, they should be replaced before you
check the tightening torque.
- Replace the flat tire with a new one and
have it installed on your vehicle as soon a s
possible. Remount the wheel cover.
Until then , drive with extra care and at re
duced speeds.
A WARNING
- If yo u are going to e quip your ve hicl e
wit h tires or rims which differ from those
which were factory installed, then be sure to read the information
9 page 245,
New tires and replacing tires and
wheels .
-Always make sure the damaged wheel o r
even a flat tire a nd the jack a nd tool kit
ar e prope rly secu red in the luggage com
pa rtment an d are no t loose in the pas
s e nge r compa rtm en t.
- In an accid ent or sudde n man euver they
co uld f ly forw ard, inju ring anyo ne in the
ve hicl e.
- Always s to re damaged wh eel, jack a nd
t oo ls se curely in the luggage co mpa rt
men t. Ot he rwi se, in an a ccident or sud
d en maneuve r they co uld f ly forw ard,
causing inj ury to p assen gers in the ve hi
cle.
(D Note
Do not use comm erc ia lly availabl e tire
se alant s. Oth erwise, the e lec trical co mpo
nen ts of the tire press ure moni to ring sys
tem will no longer work p rope rly a nd t he
senso r fo r the tire pressure mon itor ing
system w ill have to be rep lace d by quali
fied workshop.
2 76 Emergency situations
• Press the cover in by applying short strong
pressure to the bottom part to release it
from the bumper
¢ fig. 221 .
• Screw the towing loop tightly in the thread
ed hole as far as it will go and tighten it with
the wheel wrench
¢ fig . 222 .
Remove the towing loop when you are done
using it and place it back in the vehicle tool
kit . Install the cover in the bumper. Always
keep the towing loop in the vehicle.
A WARNING
If you do not screw the tow ing loop com
pletely, it could come out of the threaded
hole while the vehicle is being towed caus
ing damage to the vehicle and possible se
rious personal injury.
Rear towing loop
Only install the rear towing loop when it is
needed.
Fig . 223 Rear bum per: cover
Fig. 224 Rear bum per: screw ing in tow ing loop
There are threads located behind the right
side of the rear bumper where a towing loop
can be installed . The threads are located be
hind a cover.
-
• Remove the towing loop from the vehicle
tool kit.
• Press inward strong ly to the button side of
the cap to remove it from the bumper
¢fig. 223.
• Screw the towing loop tightly in the thread
ed hole as far as it will go and tighten it with
the wheel wrench¢
fig. 224.
Remove the towing loop when you are done
using it and place it back in the vehicle tool
kit. Always keep the towing loop in the vehi
cle.
A WARNING
If you do not screw the towing loop com
pletely, it could come out of the threaded
hole while the vehicle is be ing towed caus
ing damage to the vehicle and possible se
rious personal injury.
Loading the vehicle onto a flat bed truck
Fig. 225 Vehicle on flat bed truck
Front hook up
• Align the vehicle with the centerline of the
car carrier ramp.
• Attach the winch hook to the front towl ine
eye previously installed.
Rear hook up
• Align the vehicle with the centerline of the
car carrier ramp .
• Attach the winch hook to the rear tow line
eye prev iously installed.
-
"' N
a:: I.J ""'. rl I.O
"' rl
"' rl
Technical data
Vehicle identification
F ig. 228 Veh ide Identificat ion Number (VlN) plate: lo·
cat ion on driver's side dash pane l
XXXXX XX · X -XXXX XXX
~ fAllftlli. -llllll · NR. ~ W!ru -IIOO -NO.
xx
XXXX XXXX XX X XXXXXXXX
XXX XXX
IYP /TYPE
XX XXXXX XX XX X X XX
XXX KW XXX
®i ~W.::·f :l~~ XXXX XXX XXX
©+ ::rw= xxxx I xxxx XXX I xx
M. · AUSSt I IJ'IIDIIS
~--
EOA 7D5 4UB 6XM SSG SR W
2EH JOZ
1L B lAS 1B A
3FC SMU 7Xl
FDA 9G3 OG7 OYH OJF
TL6 3KA 8EH UlA X98 027
l XW 803 908 824 D2D
7T6 CV7 7KO 4X3 2K2
3L4 4KC 3YO 413 502
1SA 7GB 01A 4GO
XX. X XX X XX X XXXX
Fig. 229
The vehicle identification label- in side the
l u ggage compartme nt
Vehicle Identification Number (VlN)
The Veh icle Identification Number is located
in different p laces :
- under the w indshield on the driver's side
¢fig. 228.
- in the MMI: Select: Function button ICAR ! >
(Car)* systems > Servicing & checks > VIN
number .
-on the vehicle identification label.
Techni cal data 2 79
Vehicle identification label
The vehicle identification label is located in
the luggage compartment in the spare wheel
well.
T he label¢
fig. 229 shows the following vehi
cle data:
(D Vehicle Identificat ion Number (VIN)
@ Vehicle type, engine output, transmission
® Engine and transmission code
© Paint number and interior
® Optional equipment numbers
The information of the veh icle identification
label can also be found in your Warranty
&
Maintenance booklet .
Safety compliance sticker
The safety compliance sticker is your assur
ance that your new veh icle complies with all
applicable Federal Motor Vehicle Safety
Standards which were in effect at the time the
vehicle was manufactured. You can find this
sticker on the door jamb on the driver's side.
It shows the month and year of production
and t he vehicle identification number of your
vehicle (perforation) as well as the Gross Vehi
cle Weight Rating (GVWR) and the Gross Axle
Weight Rating (GAWR) .
High voltage warning label
The high voltage warning label is located in
the engine compartment next to the engine
hood release. The spark ignition system com
plies with the Canadian standard ICES-002 .
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rating (GAWR) for
front and rear are listed on a sticker on the
door jamb on the driver's s ide.
The Gross Vehicle Weight Rating includes the
weight of the basic vehicle plus full fuel tank,
oil and coolant, plus maximum load, which in
cludes passenger we ight (150 lbs/68 kg per
II>--
M N
0:: <.J 'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
steadily reduced the scope of maintenance
and repairs which can be carried o ut by vehicle
owners.
Also, safe ty and en vironment al con
cerns p lace very strict limits on the nature of
repairs and adjustments to engine and trans
miss io n parts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth
er equipment availab le to specially trained
workshop personne l in order to assure proper
pe rformance, reliab ility and safety of the vehi
cle and its many systems .
Improper ma intenance, adjustments and re
pa irs can impair the operation and reliability
of your vehicle and even void your vehicle war
ranty. Therefo re, p roof of servic ing in accord
ance w ith the maintenance schedule may be a
condition for upholding a poss ible war ran ty
claim made within the warranty period .
Above all, operational safety can be adversely
affected, creating unnecessary risks for you
and your passengers .
If in do ubt about any serv icing, have it done
by your authorized Audi dealer or any othe r
p roperly equipped and q ualified works hop .
We strong ly urge you to give yo ur auth o rized
Aud i dea ler the opportuni ty to perform all
schedu led maintenance and necessary repairs .
Your dea ler has the facilities, original parts
and tra ined spec ialists to keep your vehicle
running properly.
Performing limit ed ma inten ance yourself
The fo llow ing pages describe a limited num
ber of proced ures which can be pe rformed on
your vehicle with ordina ry too ls, should the
need arise and trained personnel be unavaila
ble. Before performing any of these proce
dures, always th oroughly read all of the appli
cable text and carefully follow the instruc
tions given . Always rigorously obse rve the
WARNINGS provided.
Before you check anything in the engine
c ompartm ent, a lway s re ad and heed all
WARNINGS ~
A and ~ A in Working in the
engine compartment on page 211.
Con sumer In formation 283
_& WARNING
- Ser ious personal injury may occur as a re
sult of improperly performed mainte
nance, ad justments or repa irs .
- Always be extremely ca reful when work
ing on the vehicle . Always follow com
monly accep ted safety pract ices and gen
era l common sense. Never r is k personal
inju ry.
- Do not attempt any of the maintenance,
checks or repairs descr ibed o n the fol
lowing pages if you are not fully familia r
wit h these or othe r procedures with re
spect to the ve hicl e, or are uncertain how
to p roceed .
- Do not do any work without the proper
too ls and equipment. Have the necessa ry
wo rk done by your authorized A udi deal
er or another proper ly equipped and
qualified wor kshop.
- The engine compartment of any motor
veh icle is a potentially hazardous area.
Never reach into t he area around or
touch the rad iator fan. It is temperature
contro lled and can switch on suddenly -
even when the engine is off. The radiato r
fan switches on automat ically when the
coo lant reaches a certain tempera ture
and will cont inue to run until the coo lant
temperature drops .
- Always sw itch o ff the ignition before any
one gets under the vehicle.
- Always support your veh icle with safety
s tands if it is necessary to work under
neath the vehicle. The jack s upplied with
the vehicle is not adequate for this pu r
pose and cou ld collapse causing serio us
personal injury.
- If you m ust wor k unde rneath the vehicle
with the wheels on the g round, a lways
make sure the vehicle is on leve l ground,
that the wheels a re a lways securely
blocked a nd that the engine cannot be
started.
- Always ma ke sure the transmission se
lecto r lever (automatic transmission) is •
•
286 Index
A
A/C (automatic climate control) .. .... .. 70
Accessories .. ... .. ..... ......... .. . 284
Active lane assist . . . . . . . . . . . . . . . . . . . . 90
Activating and deactivating . .. .. .. .. . . 91
Cleaning the camera area ...... .... . 202
Description . .................. ..... 90
Instrument cluster indicator light . . . . . 91
Mes sages .. ................ ... .... 91
Notes on instrument cluster display . . . . 91
Setting the steering wheel vibrat ion . . . . 92
Adaptive air suspension/sport .. ... ..... 96
Adaptive cruise control ....... ... .... .. 81
Cleaning the sensor ........ ... .. .. . 202
Messages . . . . . . . . . . . . . . . . . . . . . . . . . 88
Request for driver intervention . . . . . . . . 86
Stop-and-go traffic . . . . . . . . . . . . . . . . . 85
Adaptive Light (defective) ....... .... .. 21
Adding Engine coolant .................... 218
Engine oil .... ........... .. .. .... . 215
Windshield washer fluid ....... .... . 224
Addit ives
Engine oil .... .... ...... ... .. .. ... 215
Adjusting Air distribution (automatic climate con-
trol) ...... ................... ... .. 71
Front seats . . . . . . . . . . . . . . . . . . . . . . . . 53
I nstrument illumination ............. 47
Steer ing column e lectrically .. .. .. .. . . 73
Steering column manually . .. .. .. .. . . 73
Temp eratur e (automatic climate contro l) 71
A irbag system . . . . . . . . . . . . . . . . . 139 , 160
Advanced Airbag System ............ 143
Advanced Airbag System components . 147
Care . .. .. .. ............. .. .. .. .. . 155
Children .................. .. .... . 167
Child restraints .............. ..... . 167
Components (front airbags) . ... .. .. . 147
Danger of fitting a child seat on the front
passenger seat .................... 141
Disposal . .. ............. .. .. .. .. . 155
Front airbags . . . . . . . . . . . . . . . . 143, 145
H ow do the front airbags work? . . . . . . 149
H ow many airbags does my vehicle
have? ... .. .. ... ........ .. .. .. .. . 147 How
the Advanced Airbag System com-
ponents work together ............ . 149
Impo rtant sa fety instructions on the
knee airbag system ................ 158
Important things to know ........... 139
Knee airbags ..... ................ . 156
Monitoring .. .. .. .. ..... ........ .. 151
PASSENGER AIR BAG OFF light ....... 152
Repairs .......................... 155
Safety instructions ... .......... .. .. 154
Side airbags ..... ................. 158
Sid e curtain airbags ................ 161
Warning/indicator lights ............. 18
Warning/Indicator lights ........... 151
When must the system be inspected? 151
Aircraft Transpo rting your vehicle
Alcantara 277
Cleaning .. .. .. .. ... .......... .. .. 204
All-wheel drive .. .. ............. .. .. 193
Winter tires . .. .. ...... .... ... .... 252
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Ambience lighting . .......... ...... .. 47
Anti-free ze
refer to Engine coolant ........... .. 217
Anti- lock b raking system ............ . 187
Warning/indicator lights ............. 18
Anti-slip regulation ... .......... .. .. 187
Warning /indicator lights ........ .. .. . 18
Anti-theft systems
Electronic immobilizer ............. .. 32
Ashtray ... ..... .. .. .............. .. 59
Audi braking guard
refer to brak ing guard .......... .... . 81
Audi drive select
refer to drive select ............... .. 96
Audi Service Repair Manuals and Litera-
ture ... .... .... .. ............. .... 282
AUTO automatic climate control . . . . . . . . . . . . 71
Automatic headlights ............... 44
Auto Lock . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Automatic belt retractor ............. 133
Automatic climate control
Air vents .. .... .. ................ .. 71
Automatic recirculation ............ .. 72
Operation . . . . . . . . . . . . . . . . . . . . . . . . . 70
M N
0:: <.J 'SI: ,...., \!) er, ,...., er, ,....,
Setup ..... .. .... .. .... ... .. .. .... 72
synchronizing ... .. .... ... .. .. .. .... 71
Automatic S hift Lock (ASL) .. .. .. .. .. . 104
Automatic transmission . . . . . . . . . . . . . . 103
Automatic Shift Lock (ASL) . .. .. .. .. . 104
Dnvmg .. ..... ........... ... ... .. 105
Emergency mode .............. .... 107
E mergency release ........ .. .. .. .. . 108
Kick-dow n . . . . . . . . . . . . . . . . . . . . . . . . 107
M anual sh ift program ..... .. .. .. .. . 10 7
Selec to r l ever . . . . . . . . . . . . . . . . . . . . . 103
Automatic wipe rs ....... ...... .... ... 48
Auto Safety Hotline ........ .. .. .. .. . 128
Aver age consumption ....... .. .. .. .. .. 24
Average speed . . . . . . . . . . . . . . . . . . . . . . . 24
Avoid damaging the vehicle . ... .. .. ... 197
B
B ag hoo ks . . . . . . . . . . . . . . . . . . . . . . . . . . 6 7
Battery . .. ... ...... ............. .. 22 1
C ha rging . ............ ...... .... .. 223
I mportant war nings ...... .. .. .. .. . 22 1
J um p starti ng ............ .... .. .. . 273
L ocat ion . .. ............. .. .. .. .. . 22 1
l ow ..... .. .. .. .. .. .... ... .. .. ... 193
Replacing the batte ry .. ... .. .. .. .. . 224
State of charge . ... .... ... .. .. .... . 193
W inter operation ......... .. .. .. .. . 221
Working on the battery .... .. .. .. .. . 221
B efore dr iving . ..... .... ... .. .. .. ... 120
Blended gasoline .... ...... .. .. .. .. . 206
Blower (automatic climate control) .. .. .. 71
B oost displ ay . . . . . . . . . . . . . . . . . . . . . . . . 28
Booster seats . . . . . . . . . . . . . . . . . . . . . . 17 4
Boost pressure indicator . ... .. .. .. .. .. 28
B rake flu id
C hanging the brake fl uid ... .. .. .. .. . 220
Che ckin g the br ake fl uid level . .. .. .. . 220
What is the cor rect brake flu id leve l? .. 220
What should I do if the bra ke fl uid warn-
ing light comes on? .... ... .. .. .. .. . 220
B ra ke system
Anti -lo ck bra king sys tem ... .. .. .. .. .. 18
B rake ass ist system .... ... .. .. .. .. . 18 7
Brake booster ... .. .... ... .. .. .. ... 191
Bra ke fl uid ... .... .... ... .. .. .. ... 220
Inde x 287
Brake fluid specifications fo r refill and re -
placement . ... .... . ... ...... ... .. 220
B rake pads . ... .. .. . .. ... .... ... .. 196
E lectromechanica l parking brake ... .. . 77
Flu id reservo ir . .. .... ............. 220
How does moistu re or road salt affect the
brakes? ... .. .. .. .. . .. .... .... .. .. 191
Warning/ind icator lights ........... .. 14
Wor n bra ke pads symbo l ........ .... . 19
braking guard Settings ........ .. ..... ........... 88
B raking guard ..... .. . .. .. ..... ... .. . 81
Messages ... .... .. . .. .. ..... ... .. . 88
B reak-in per iod .. .. .. .. ........... .. 196
Br ake pads .. .. .. ................. 196
T ires ... .. .. .. .... . ... ...... ... .. 196
Bulbs .. ... ... .. .... .......... ..... 272
C
Californ ia Proposition 6S Warn ing . .. .. 212
Battery spec ific .................. . 222
Capacities . ... .. .... . ... ...... ... .. 280
Engine o il ... .. .. ................. 213
Carbo n parts
Cleaning . . . . . . . . . . . . . . . . . . . . 203, 204
Car carrier Transpo rting your vehicle ........... 277
Care ......... .. .. ................. 201
Cargo area .. .. .. .. ............... .. 126
Cargo ne t . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Catalytic converter . . . . . . . . . . . . . . . . . . 197
Cen te r armres t
Cockpit . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Cent ral lock ing .. .. .. . .. .... .... .. .. . 33
E mergency locking .. .............. .. 37
Certif ication . ... .. .. .. ... ..... ... .. 285
Changi ng a wheel .. ............. .... 263
Changi ng engine oil ................. 216
Checking Engine coolant level .. .. ..... ... .. .. 217
Tire pressure . .. ...... ............. 237
C hild rest rain ts
Danger of using child restrain ts in the
fr ont seat ... .. .... . ... ...... ... .. 141
Where can I get additional informat ion
about child restraints and the ir use? .. 183
•
•