2015 AUDI RS5 COUPE radio controls

"' N
0:: l­oo
rl I.O
"' N
"' rl
Driver information
system
Introduction
The Driver information display inside the instru­
ment cluster provides you, the driver, with im­
portant information.
Fig. 7 Instrument cluster: ce nter display
Fig . 8 Wipe r lever: controls fo r the men u display
Cent er dis play
With the ignition on, the display in the Driver In­
formation System shows the following informa­
tion :
- CD* inserted or Radio * station set
- Outs ide temperature* : At temperatures below
41 °F (+S °C), a snowflake symbol appears in
front of the temperature display¢&. .
- Wa rning if one of the doors, front lid o r engine
compartment lid is not closed.
Additional function s
You can open the following functions in the Driv­
er Information System display by pressing the
I RESET I button ¢ fig. 8 one or more times:
Digital speedometer*
T ire pressure monitoring*
¢page213
Dr iver inform atio n sy stem
Trip computer Q page24
Service interval disp lay ¢page26
Speed warning Qpage 77
Gearshift selector positions Au-¢page 81
tomatic transmission
Adapt ive cruise control*
¢ page BB
Lap timer ¢page 27
Eng ine oil temperature indicator ¢ page 26
Auto Che ck Control
Some functions and vehicle components are
scanned for their operati ng status when you
switch the ign ition on and whi le you a re driving.
Malfunctions or required service procedures are
s ignaled audib ly and ind icated by red and yellow
illuminated symbols and rem inders in the dis­
play.
A WARNING
-
- Never rely exclusively on the o utside tem­
perature display to determine if a road sur­
face is icy or not. Keep in mind that road sur­
faces, especially bridges and overpasses, could be ice covered and slippery even at an
outs ide temperature above 41 °F (+5 °C).
- Always remember, even i f the "snowflake"
symbo l (ice warning) does not appea r in the
display, black ice could be on the road.
- Always reduce your speed and drive with
specia l care in cold weather cond itions when
the chance of encountering icy road surfaces
increases.
(D Tips
If the vehicle is stationary, or if you are driv­
i ng at a very low speed, the temperature
shown in the disp lay m ight be slightly higher
than the act ual outs ide temperatu re. This is
caused by the heat being radiated from the
engine.
23

M N
0:: l­oo ,...., \!) 1.1'1
N 1.1'1 ,....,
Single-trip memory (Trip computer 1)
The s ingle-t rip memory s to res the trip informa­
tion from the time the ignition is tu rned on until
it is turned off. If the trip is continued
within 2
hours
from the time the ignition was turned off,
the new data w ill be included in the calculat ion of
the current trip information. If the trip is inter­
rupted for
more than 2 hours the memory is re­
set automat ically.
Total-trip memory (Trip computer 2)
Unlike the sing le-trip memory, the tota l-trip
memory is not reset automatically. Th is permits
you to evaluate your driving data for the entire pe riod between manual resets.
Operation
The trip computer is controlled by two switches
on the windshield wiper lever.
F ig. 11 Wind shield w iper lever: controls for the trip com­
puter
Operating
.. To d isp lay the trip computer memory leve ls,
press the
I RESE T I button @¢ fig. 11 repeated­
ly until the des ired memory level is shown in
the d isplay .
.. To display trip information w ith in a memory
level , press the top or bottom part of the func­
t ion select io n switch @.
The trip computer will not operate unless the ig­
nition is on. When you turn on the ignition, the
function that was in use when you last turned the
i gn ition off will be d isp layed.
In addition to information about the trip comput­
er (tr ip computer 1 and 2), information about
other systems can also be shown in the display.
Driver information system
To switch the display between the different infor­
mation, tap the
! RESET I button @briefly.
Resetting values to zero
"Select a value in the desired trip computer .
" Press and hold the
I RESET I button @for at
least one second. A ll values in the selected trip
computer are reset to zero .
With some vehi cle equ ipment levels, the values
for the single trip or total trip memory can also
be reset in the Infotainment system
¢page 25.
@ Tips
All stored values w ill be lost if the vehicle bat­
tery is disconnected.
Basic Settings for the trip computer
The radio or MMI* operating unit is used for set­
ting the trip computer's basic settings.
"Select: Function button !CAR !> Instrument
cluster> On-board computer
1 or On-board
computer
2 .
The values in the single-tr ip or the total-trip
memo ry can all be reset to zero at the same time
un der
Reset in the menu.
In add ition, you can determine what information
from the trip computer should be shown in the
i nst rumen t cl uste r display.
If one of the pieces of
drive r information is tu rned
Off , that driver infor­
mation will not be shown in the display. The in­
formation will continue to be calculated by the
trip computer and can be turned back
On at any
t ime.
(D Tips
This function is not available on all vehicles.
25

Warm and cold
Operation
We recommend pressing the !AU TO ! button and setting the temperature to 72 °F (22 °C).
Fig . 72 Automatic climate control sys tem: control
F ig . 73 3-zone del ux e automat ic climate controt•: controls
Press the buttons to turn the functions on or off.
Use the dials to adj ust the temperature, the
b lo wer speed and the air distribution. The LED in
a button will light up when the function is
switched on. The settings are displayed for a few
seconds in the radio or MMI* display.
In vehicles with a 3-zone deluxe automatic cli­
mate control systems*, the driver and front pas­
senger side can be adjusted sepa rately. The set­
tings are also disp layed in the climate control
system display .
68
I OFFI Switching the climate control system
on/off
The ! OFF ! button switches the climate contro l
system on or off.
It also switches on when you
press the knob. Airflow from outside is blocked
when the cl imate control system is switched off.
IA/C l Switching cooling mode on/off
The air is not cooled and humidity is not removed
when coo ling mode is switched off. This can
cause fog on the windows. The cooling mode is
switched off automatically at low outside tem­
peratures.