2015 AUDI RS5 CABRIOLET warning light

24 4 What do I do no w?
• Screw the accompanying filling hose com ­
pletely onto the bottle. This breaks through
the fo il seal automat ica lly at the connec­
t ion.
• Remove the valve cap from the tire valve and
unscrew the valve insert us ing the accompa ­
nying valve insert tool
q fig . 190 .
• Lay the valve insert on a clean surface .
• Remove the sealing p lug from the filling
hose and connect the hose to the t ire va lve.
• Hold the bottle with the bottom fac ing up­
ward and empty the entire contents into the
tire.
• Then pu ll out the hose and screw the valve
insert tightly back into the tire valve.
Inflating a ti re
• Screw the fi lling hose for the electric air
pump onto the tire valve and insert the con ­
nector into the cigarette lighter .
• Inf late the tire between 2.0 and 2.S bar and
read the pressure from the gauge.
• If this tire pressure is not reached, drive
your vehicle approximately 10 meters for ­
ward or backward so that the sealant can be redistr ibuted i nside the tire.
If at th is time
the required air pressure still cannot be reached, the t ire is too bad ly damaged and
cannot be repaired with the tire sea lant.
Final check
• After dr iving for about 10 minutes, stop and
check the t ire pressure .
• If tire pressure is less than 1.3 bar, the ti re
is too seve rely damaged. Do not cont in u e to
drive . Seek pro fessional assistance.
8_ WARNING
- Turn on the eme rgency flashers and set
up the emergency triangle if you have
flat tire while in moving traff ic. This is
for your protection and the for the safety
of other d rivers .
- Have all passengers leave the vehicle and
stay away from the danger zone (fo r ex­
ample, beh ind a guard rail). -
Read and follow the manufacturer's safe­
ty precautions on the compressor and in
the instructions on the bottle of sealant!
- If a tire pressure of 2.0 bar cannot
reached after inflating for six minutes,
then the t ire is too severely damaged. Do
not continue driving!
- Obta in qualified help if it is not possible
to perform the repair with the tire seal­
ant.
- If the tire pressure is less than 1.3 bar
after 10 m inutes of driv ing, then the the
tire is too seve rely damaged . Do not con­
tinue dr iving. Seek profess iona l assis­
tance.
Q) Note
Particular care is necessary if you are mak­
i ng a tire repa ir on a steep incl ine .
@ Tips
-Do not operate the electric air pump for
more than 6 minutes without stopping,
otherwise it can overheat . When the a ir
pump has cooled down, you can continue
t o u se i t.
- If sealant has spilled out, let it dry and
then you can remove it by peeling it away
like a foil.
- Rememb er to obtain a new bott le of
sealant from yo ur autho rized Aud i deale r
after repairing a tire. After this, the func­
tionality of the tire repair set is resto red.
- Obey all laws.
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger 's safety when chang­
ing a wheel.
• After you experience a tire failure, pull the
car we ll away from mov ing traffic and try to
reach
le vel ground before you stop q ,& .
• All passengers should lea ve the car and
move to a safe location (for instance, behind
the guardrail)
q ,& . ..,.

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
~ Engage th e pa rkin g bra ke to p revent your
v eh icl e from ro lling unintentionally ¢,&. .
~ Move the sele ctor le ve r to the P po siti on.
~ Take the jack c> page 242 out of the l uggage
compartment .
_& WARNING
You or your passengers cou ld be injured
wh ile changing a wheel if you do not fol­
low t hese safety precautions :
-If you have a flat t ire, move a safe dis­
tance off the road. Turn off the eng ine,
tu rn the emergency flashers o n and use
othe r warning dev ices to alert o ther mo­
torists.
- Make su re that passengers wai t in a safe
place away from the vehi cle and well
away from the road and traff ic.
- T o help p revent the veh icle from mov ing
sudden ly and possibly slipping off the
jack, a lways fully set the parking brake
and block the whee l diagona lly opposite
the wheel being changed with the fo ld­
ing chocks or other objects. When one
front wheel is lifted off the ground, plac­ ing the Automat ic Transm iss ion in "P"
(Park) w ill
not prevent the vehicle from
moving.
- Before you change a wheel, be sure the ground is level and firm. If necessa ry,
use a sturdy board under the jack.
- Always store the vehicle tool kit , the
jack* and the replaced ti re in the luggage
compartment
c> page 118.
([) Note
If you are chang ing the wheel on a steep
incline, use a rock or similar object to
b lock the opposite whe el to prevent the
veh icle from mov ing.
Obey all laws.
What do I do now? 245
Changing a wheel
When you change a wheel , follow these­
quence described below step-by-step and in
exactly that order.
l. Remove the w heel bolt cap s* . For more
details see also
c> page 246, Wheels with
wheel bolt caps .
2. Loosen the wheel bolts .:>page 246.
3. Locate the p roper mounting point fo r the
jack and align the jack below that point
.:> page 247 .
4. Lift the car with the jack Q page 247 .
5. Remov e the wheel with the flat tire and
then install the other wheel
c> page 248.
6. Tig hten all wheel bolts lightly.
7.
Lower the vehicle with the jack .
8 . Use the wheel bolt w rench and
firmly
t ighten all wheel bolts in a crisscross pat­
te rn
Q page 246.
9. Replace the whe el bolt cap s*.
WARNING
A lways read and fo llow all WARN INGS and
information
Q .&. in Raising the vehicle on
page 247
and ¢ page 249 .
After changing a wheel
A wheel change is not complete without the
doing the following .
~ Always store the vehicle tool kit, t he jack*,
and the rep laced tire in the lugg age com­
par tment
Q page 118.
~ As soon as possib le, have the t ight ening
torque s
on all wheel bolts checked with a
torque w rench. The correct tightening to r­
que is 90 ft lbs. (120 Nm).
~ Have the flat tire replaced as soon as possi­
ble.
(D Tips
- If you not ice that the wheel bolts are
corroded and diff icult to turn while
chang ing a tire, they should be replaced
before you check the tightening torque . •
•

"' N
a: LL co
rl I.O
"' rl
"' rl
down on the end of the wheel bolt
wrench with
one foot only. As you do so,
ho ld on to the car to keep your ba lance
and take care not to slip.
Raising the vehicle
The vehicle must be li~ed with the jock first
before the wheel can be removed.
Fi g. 193 Sill panels: markings
Fig. 194 S ill: posit ion ing the vehicle jack
The location of the jack point is indicated by
an indentat io n on the unders ide of the vehicle
c:>fig . 193 .
.,. Activate the park in g brake to prevent the
vehicle from rolling u nintentionally.
.,. Move the selecto r lever to position P.
.,. Find the
mark ing (raised area) on the sill
t h at is nearest the wheel that wi ll be
c hanged
c:>fig. 193. Behind the marki ng,
there is a
lifting point on the sill for the ve ­
hicle jack.
.,. Turn the
veh icle j ack located under the lift­
ing point on the s ill to raise the jack until
the jaw
c:> fig. 194 ® covers the notch on
the vehicle
c:> .&. c:> (D .
.,. Al ign the vehicle jack so the jaw @ covers
t h e notch and t he base p late @ is flat on What do
I d
o now ? 24 7
the floor . The base plate @ must be
vertical
under t he lifting point @.
.,. Insta ll the rod on the vehicle jack: Insert the
rod into the opening on the handwheel. Turn
the rod left or right to secure it .
.,. Continue raising the jack w ith the rod unt il
the wheel lifts off the ground slightly .
Position the vehicle jack
only under the desig­
nated lifting points on the s ill
c:>fig. 193.
There is exactly one locat ion for each wheel.
T he jack must not be positioned at any other
location
c:> ,& c:>(D .
Soft ground under the jack can cause the ve­
hicle to slip off the jack . Always place the jack
on fi rm ground . Use a flat, stab le support if
necessary. Use a no n-slip surfa ce such as a
rubber mat on a
s lippery surface such as tile .
_&. WARNING
-You or your passengers co uld be in ju red
while changing a wheel if you do no t fo l­
low these safety p reca utions:
- Position the vehicle jack on ly at the
designated lifting po ints and align the
j ac k. Otherw ise, the vehicle jac k co uld
s lip and cause an injury if it does not
have sufficient hold on the vehicle.
- A soft or unstable su rface unde r the
j a ck may cau se the ve hicle to slip off
the j ack. A lw ays p rov ide a firm b ase for
the j ack o n the ground .
If necessary,
u se a st urdy boa rd under the jack .
- On hard, sl ippery surface (s uch as t iles)
u se a ru bber mat o r similar to prevent
the jack from slipping .
- T o help p revent injury to yo urself and
your passengers:
- Do not ra ise the vehicle until you are
su re the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the veh icle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
j u st as necessary a nd then cont inue to
r aise t he jack .

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
No. Consumer
A/C system pressure sensor,
electromechanical parking
brake, Homelink, automatic
3 dimming interior rear view
m
irror, air quality/outside
air sensor, Electronic Stab ili-
zation Control (button)
5 Sound
actuator
6 Headlight
range cont rol/
head light (cornering light)
7 Headlight (corner
ing light)
Contro l modu les (e lectro-
8 mechanical parking brake,
shock absorber, quattro
sport), DCDC converter
9 Adaptive cru ise contro l
10 Shift gate/clutch
sensor
1 1 Side ass ist
1 2 Headlight range
control,
park ing system
13 Airbag
14 Rear wiper (allroad)
1 5 Auxi
liary fuse (instrument
pane l)
16 Aux
iliary fuse terminal 15
(engine area)
Fuse p anel @ (brown )
No. Con sumer
2 Brake light sensor
3 Fuel
pump
4 Clutc h sensor
5 Left
seat heating with/w ith-
out seat vent ilation
6 Electronic Stab
il iz at ion Con-
tro l (e lectric)
7 Horn
Front left door (window reg-
8 ulator, centra
l locking, mir-
ror, switch, lighting)
9 Winds hield wipe r motor
1 0 Electronic
Stabilizat ion Con-
trol (valves)
Fuses and bulb s 251
Amp s No. Consumer Amps
•
Two-door models: rear left
• window regulator; Four-
11 door models:
rear left door
30
5 (window regulator, central
lock
ing, switch, lighting)
12 Rain and light sensor
5
5
Fuse pan el© (r e d )
5/7,5 No . Consumer Amps
3 Lumbar support 10
7,5 4 Dynamic steering 35
s Interior lighting (Cabriolet)
5
5 6 W
indshield washer system,
35
h eadlight washe r system
5 7 Vehicle electrical
system
20
control module 1
5
5
8
Vehicle e lectr ica l system
30
control module 1
5 9 Left rear window regulator
7,5/20
motor (Cabriolet)/sunroof
5
15 10 Vehicle e
lectrical system
30
control module 1
10 11 R
ight rea r window regulato r
7,5/20
(Cabriolet)/sun shade motor
40 12 Anti-theft
alarm warning
5
system
Amps
5
25 5
15/30
5
15
30
30
25

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
No. Consumer
5 Electromechanical
parking
brake
6 Electronic damping control
7
Electromechanical parking
brake
8 Rear exterior lighting
9 quattro sport
10 Rear
exterior lighting
1 1 Central locking
12 Termina
l 30
Fu se pa nel © (brown )
No. Con sumer
1 Luggage compartment lid
control module (allroad)
2 1
2-volt socket, cigarette
lighter
3 DCDC
converter path 1
4 DCDC converter path 2,
so und amplifier, radio
6
Right upper cabin heat ing
(Cabr iolet)
7
Electromechanical parking
brake
Right front door (w indow
9 regu lator, central lock ing,
m irror, swit ch, lig hting)
10 Left upper
cabin heating
(Cabriolet)
Two -door models: rear right
window regulator; Four-
11 door mode
ls: rear right door
(window regulator, central
locking, sw itch, lighting)
12 Cell phone prep
Fu se panel © (black )
No. Consumer
1 Right front seat heating
4
MMI
5 Radio
6 Rear view camera
Amp s
5
15
30
30
35
30
20 5
Amp s
30
20
40
30
30
30
30
30
30
5
Amps
15
7,5
5
5
Fu ses and bulb s 253
No. Consumer Amps
7
Rear window heater (all-
30
road)
8 Rear Seat Entertainment 5
Bulbs
Replacing bulbs
For your safety, we recommend that you hove
your authorized Audi dealer replace any bulbs
for you .
It is becoming increasingly more and more
difficult to replace vehicle light bulbs since in
many cases, other parts of the car must first
be removed before you are able to get to the
bulb. This applies especially to the light bulbs
in the front of your car which you can only
reach through the engine compartment.
Sheet metal and bulb holders can have sharp
edges that can cause serious cuts, parts must
be correct ly take n apa rt and then p roperly put
bac k together to he lp p revent breakage of
parts and long te rm damage from water that
can enter housings that have not been p roper­
ly re sea led .
Fo r you r safety, we re commend that you have
your autho rized Audi de aler replace any b ulbs
f or you, since your dealer has the proper too ls,
the correct bulbs and the expertise.
Gas disc har ge la mp s (Xenon l ig hts)*:
Due to the high electr ical voltage, have the
bulbs replaced by a qualified techn ic ian .
Head lights w ith Xenon light are identified by
the h igh vol tage sticker.
_&. WARNING
Changing Xenon lamps without the neces­
sary equipment can cause serious persona l
injury .
- Bulbs are pressurized and can explode
when being changed. Potential risk of in­
jury!
-
•
•

M N
er
u..
co ,...., \!) 1.1"1 ,...., 1.1"1 ,....,
Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who have the necessary tools and equipment to
perform these operations.
Starting by pushing or
towing
(D Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If the engine should fail to start because of a
discharged or weak battery, the battery can be
connected to the battery of
another vehicle,
using a
pair of jumper cables to start the en­
gine.
Jumper cables
Use only jumper cables of sufficiently
largecross section to carry the starter current
safely. Refer to the manufacturer's specifica­
tions.
Use only jumper cables with
insulated termi­
nal clamps which are distinctly marked:
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal
injury. Follow the instructions below for
safe handling of your vehicle's battery.
- Always shield your eyes and avoid lean­
ing over the battery whenever possible.
Emergency situations 255
-A discharged battery can freeze at tem­
peratures just below 32 °F (0 °C). Before
connecting a jumper cable, you must
thaw the frozen battery completely, oth­
erwise it could explode.
- Do not allow battery acid to contact eyes
or skin . Flush any contacted area with
water immediately .
- Improper use of a booster battery to
start a vehicle may cause an explosion.
- Vehicle batteries generate explosive gas­
es. Keep sparks, flame and lighted ciga­
rettes away from batteries.
- Do not try to jump start any vehicle with
a low acid level in the battery.
- The voltage of the booster battery must
also have a 12-Volt rating. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged bat­
tery. Use of batteries of different voltage
or substantially different "Ah" rating
may cause an explosion and personal in­
jury.
- Never charge a frozen battery. Gas trap­
ped in the ice may cause an explosion.
- Never charge or use a battery that has
been frozen. The battery case may have
be weakened.
- Use of batteries of different voltage or
substantially different capacity (Ah) rat­
ing may cause an explosion and injury.
The ca pa city (Ah) of the booster battery
should not be lower than that of the dis­
charged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c::;,page 195.
(D Note
-Applying a higher voltage booster bat­
tery will cause expensive damage to sen­
sitive electronic components, such as
control units, relays, radio, etc.
- There must be no electrical contact be­ tween the vehicles as otherwise current
could already start to flow as soon as the
positive(+) terminals are connected. ..,. •
•

256 Emergency situations
@ Tips
The discharged battery must be properly
connected to the vehicle's electrical sys­
tem. When jump starting or charging the
battery, never connect the negative
ground cable to the battery negative post
because the batte ry manager system must
be able to detect the battery 's state of
charge. Always connect the negative
ground cab le to the negative ground post
of the battery manager control unit.
Use of jumper cables
Make sure to connect the jumper cable
clamps in exactly the order described below!
Fig. 201 Engine compartment: Connectors fo r jum per
cables and charger
Fig. 202 Jump sta rting wi th the battery of anot her ve ·
h ide :@ booster battery, @ disc harged vehicle battery
The procedure described below for connecting
jumper cables is intended to provide a jump
start for your vehicle .
Vehicle with discharged battery:
.. Turn off lights and accessories, move lever
of automatic transmission to N (Neutral) or
P (Park) and set parking brake .
Connect POSITIVE(+) to POSITIVE(+)
(red)
.. Remove the cover above the jump start con­
nection .
.. Open the cover on the positive pole
¢fig. 201.
1. Connect one end of the red positive cable
on the
jump start bolt c::> fig. 202 @
(Bolts under cover= "positive") of the ve­
hicle to be started @.
2. Connect the other end to the positive ter-
minal @of the booster battery@.
Connect NEGATIVE (-) to NEGATIVE (-)
(black)
3. Connect one end of the b lack negative ca­
ble to the negative terminal @of the
booster battery @.
4. Connect the other end to the
jump start
bolt @
(Bolts with hex head= "negative")
of the vehicle to be started @.
Starting the engine
.. Start the engine of the vehicle with the
booster battery@. Run the engine at a
moderate speed.
.. Start engine with discharged vehicle battery
@ in the usual manner .
.. If the engine fails to start: do not keep the
starter cranking for longer than 10 seconds .
Wait for about 30 seconds and then try
again .
.. With eng ine running, remove jumper cables
from both vehicles in the exact
reverse or­
der .
.. Close the cover on the positive pole .
T he battery is vented to the outside to prevent
gases from entering the vehicle interior . Make
sure that the jumper clamps are well connect­
ed with their
metal parts in full contact with
the battery terminals.
A WARNING
--
To avoid serious personal injury and dam­
age to the veh icle, heed all warnings and
instructions of the jumper cable manufac-
turer . If in doubt, call for road service . ..,.

26 2 Techni cal Dat a
Gross Ax le Weight R atin g
The Gross Axle Weight Rating is the maximum
l oad that can be applied at each axle of the
vehicle
c::> &. .
Vehicle capacity weight
The vehicle capac ity we ight (max. load) is list­
ed on the driver 's side 8-p illar.
_& WARNING
- T he actual Gross Axle Weight Rat ing at
the front and rear axles shou ld not ex­
ceed the permissible weights, and their
combination must not exceed the Gross
Vehicle Weight Rat ing.
Dimensions
Length
Width
Width (across mirrors) Height (unloaded)al
-
- Exceeding permissible weight ratings can
result in veh icle damage, acc idents and
personal injury.
(D Note
- The vehicle capacity weight figures apply
when the load is distributed evenly in the
vehicle (passengers and luggage). When
transport ing a heavy load in the luggage
compartment, carry the load as near to
the rear axle as poss ible so that the vehi­
cle's handling is not impaired.
- Do not exceed the maximum permissible axle loads or the maximum gross vehicle
we ight. Always remember that the vehi­
cle's handling w il l be affected by the ex­
tra load. Therefo re, adj ust your speed ac­
cordingly.
- Always observe local regulat ions.
in (mm)
183.0 (4649)
in (mm) 73.2 (1860)
in (mm) 79 .5 (2020)
in (mm) 54.3 (1380)
al The he ight of the vehicle depends on the tires and the suspension.
When driving up steep ramps, on rough roads,
over curbs, etc. it is important to remember
that some parts of your vehicle, such as spoil-
Capacities
Fuel tank: total capacity
Windsh ield and headlight* washer fluid container ers or exhaust system components, may be
close to
the ground. Be carefu l not to damage
them.
gal (liters) 16. 1 (61.0)
quarts (liters) 4.8 (4.5)