.... N ,..: N "': ....
"' "' N
"' .....
Tire service life
The service life of tires depends
on a lot of different things includ
ing proper installation and bal
ancing, correct tire pressure and
driving style.
Fig. 149 Tire tread: tread wear indica
tors (TWI)
Tread Wear Indicator (TWI)
The original tires on your vehicle
have 1/16 inch (1 .6 mm) high
"wear indicators"c::>
fig. 149 run
ning across the tread. Depending
on the make, there will be s ix to
eight of them evenly placed
around the tire. Marks on the tire
sidewall (for example "TWI" or
other symbols) indicate the posi
tions of the tread wear indicators.
Worn tires must be replaced. Dif
ferent figures may apply in other
countries c::>
.&..
Tire pressure
Incorrect tire pressure causes pre
mature wear and can cause sud-
Tires and wheels
den tire blow-out. For this reason,
tire pressure must be checked at least once a month c::>
page 179.
Driving style
Driving fast around curves, heavy
acceleration and hard braking in
crease tire wear.
Wheel balancing
The wheels on new vehicles are
balanced. However, various situa
tions during everyday driving can
cause them to become unbal
anced, resulting in vibrations you
can usually feel through the
steering wheel.
Unbalanced wheels must be reba
lanced to avoid excessive wear on
steering, suspension and tires . A
wheel must also be rebalanced
when a new tire is installed .
Incorrect wheel alignment
Incorrect wheel alignment can
cause excessive tire wear, impair
ing the safety of the vehicle. If
tires show excessive wear, have
the whee l alignment checked by
an authorized Audi dealer or
qualified workshop.
185
What do I do now? Trunk escape handle
Appl ies to vehicles: with trunk escape handle
In case of an emergency, the front lid can be
opened from the inside using the trunk escape
handle.
.. To open the front lid pull the handle.
The trunk escape handle inside t he luggage com
partment is made of fluorescent material to glow
in the dark .
.&_ WARNING
The trunk escape handle is to be used only in
an emergency.
Vehicle tool kit
The tools are stored underneath the floor panel
in the luggage compartment.
Fig. 151 Luggage compartment: veh icle tool kit
"' Swing the luggage compar tment floo r up-
wards .
.. Remove the vehicle tool kit.
The onboard tool kit incl udes:
- Hook for removing hub cap
- Lug wrench
- Alignment pin for changing wheels
- Screwdr iver w ith reversible blade
- Towing eye
- Jack* (not a vehicle component; contact your
,..... authorized Aud i dealer i f needed)
N
I'-
~ Some of the on board items listed above are pro-
.... :5: vided on certa in models only or are optiona l ex-
N l/1 .... tras.
What do I do no w?
Before returning the jack* to its p lace, retract the
jack arm fully.
.&_ WARNING
-
Improper use of the vehicle jack can cause se-
rious personal injuries.
- Never use the screw driver hex head to
tighten wheel bo lts, since the bolts cannot
attain the necessary tightening torque if yo u
use the hex head, potentially causing an ac
cident.
- The factory-supplied jack is intended only
for your veh icle model. Under no circum
stances should it be used to
lift heavy
veh icles or other loads; you risk injuring
yourse lf.
- Never start the engine when the vehicle is
raised, which could cause an accident.
- Support the vehicle securely with appropri
ate stands if work is to be pe rformed under
neath the vehicle; otherwise, the re is a po
tential risk fo r injury.
- Never use the jack supplied with your Aud i
on another vehicle, part icularly on a heavier
one. The jack is only suitable for use on the
vehicle it came with.
Tire repair
General and safety pointers
Applies to vehicles: with Tire Mobility System
Tire repair is intended only for temporary, short
term use.
Fig. 152 Tire damage for which the Tire Mobility System Is
not suited
Your vehicle is equipped with a tire repa ir kit, the
T ire Mob il it y Sy stem ( TMS). .,.
19 9
What do I do now?
• Align the jack so that its arm@ c> fig. 158 en
gages in the designated lifting point in the door
s ill and the movable base @ lies flat on the
ground . The base @ must be
vertical under the
lifting point @.
• Wind the jack up further until the flat tire
comes off the ground
c> ,&. .
Position the vehicle jack only under the designat
ed lifting points on the sill<=>
fig. 157. There is ex
actly
one location for each side of the vehicle .
The jack must not be posit ioned at any other lo
cation
c> .&, c>(D .
An unstable surface under the jack can cause the
vehicle to slip off the jack . Always provide a firm
base for the jack on the ground . If necessary
place a sturdy board or similar support under the
jack. On
hard, slippe ry surfac es (such as tiles)
use a rubber mat or similar to prevent the jack
from slipping
c> .&, .
A WARNING
-
-You or your passengers could be injured
while changing a wheel if you do not follow
sa fety precautions:
- Position the vehicle jack only at the desig
nated lifting points and align the jack.
Otherwise, the vehicle jack could slip and
cause an injury if it does not have suffi
cient hold on the vehicle.
- A soft or unstable surface under the jack
may cause the vehicle to slip off the jack .
Always provide a firm base for the jack on
the ground. If necessary, use a sturdy
board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipping.
- To help prevent injury to yourself and your
passengers:
- Do not raise the vehicle until you are sure
the jack is securely engaged.
- Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
204
- Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack.
(D Note
A floor jack or the pads on the hoist arms
must
not be positioned at the points shown
-arrow-.
Removing the wheel
Follow these instructions step-by-step for chang
ing the wheel.
Fig. 159 Whee l chan ge: using the screwd river handle (wit h
the blade removed) to turn t he bolts
Fig. 160 Whee l chan ge: alignme nt pin inside the top hole
After you have loosened all wheel bolts and
raised the vehicle off the ground, perform the
following steps to remove and replace the wheel:
Removing the wheel
• Use the hexagonal socket in the screwdriver
handle
to completely turn out the topmost
wheel bolt and set it aside on a
clean surface .
• Screw the threaded end of the
alignment pin
from the tool kit hand-tight into the now va
cant bolt hole<=>
fig. 160.
..... N
r-N "': ..... \!) 1.1'1
N 1.1'1 .....
~ Then comp lete ly unscrew th e othe r whee l bolts
as descr ibed above.
~ Takeoff the wheel le aving the alignment pin in
t he bolt hole
Q (D.
Putting on th e w hee l
~ Lift the spare wheel and carefully slide it over
the alignment pin to guide it in place
q (D.
~ Use the hexagonal socket in the screwdriv er
hand le to screw in and tighten all wheel bo lts
s ligh tly.
~ Unscrew the alignmen t pin and insert and
t ighten the remaining wheel bolt s light ly like
the rest .
~ Turn the jack handle counter-clockw ise to lowe r
the vehi cle until the jack is fu lly released.
The wheel bolts must be clean and turn easily. Check the contact surfaces of wheel and hub . Re
move contaminants on these surfaces before in
stall ing the wheel.
The hexagonal socket in the screwdriver handle makes it eas ier to hand le the wheel bolts . The re
ve rsible blade shou ld be removed .
When mounting
un idirectional tires, observe the
d irection of rotation
q page 203 .
When removing or install ing the wheel, the
r im could hit the brake rotor/ceramic brake
roto r* and damage the rotor. Wo rk ca refully
an have a second pe rson help you .
{D) Tips
Never use the hexagonal socket in the handle
of t he screwdr iver to loose n or tighten the
wheel bo lts.
Tightening wheel bolts
~ Fi t the wheel bolt wrench ove r th e wheel bo lt
and push it down as fa r as it will go
l).
~ Close your grip aro und the end of the wrench
hand le for max im um torq ue and turn eac h
whee l bolt
cloc kwi se u ntil it s its t ight .
l) You need t he appro pria te adapte r to t ight en th e an ti- th eft
wheel bo lts
<=:> p age 20 3.
What do I d o now?
Have the tightening torque of the wheel bolts
checked as soon as possib le with a torqu e
w renc h. It should be 120 Nm .
Check the
tire pre ssure as soon as possible.
Return the veh icle tool k it to its p roper place .
A WARNING
Loosening the whee l bolts is p roh ibited; dan
ger of an accident!
(D Tips
- Never try and use the hexagonal socket in
the handle of the screwdrive r to loosen o r
tighten t he whee l bolts.
- If you hav e determined that wheel bolts are
co rroded and difficult to turn, the bolts
must be replaced before checki ng t he tor
que.
- Unt il the t ightening to rque is checked, d rive
a t redu ced s peed s as a precaution.
Notes on wheel change
Please read t he info rmation q page 186, New
tires and replacing tires and wheels,
if yo u are
going to us e a spare tire w hich is different from
the ti res on your vehicle.
After you change a tire:
- Che ck the tire pre ssure on the spar e imm ed i
ate ly after mounting .
- Have the wheel bolt tightening torque
c he cked with a torque wrench as soon as po s
s ible by your authorized Audi d ealer or a
qualified service station .
- With steel and all oy wheel rim s, th e wheel
bolts ar e corre ctl y tightened at a torque of 90
ft lb
( 120 Nm ).
- If you noti ce while changing a tire that the
wheel bolts are corroded and diffi cult to turn ,
then the y should be replaced before you check
the tightening to rque .
IJ>-
205