2015 AUDI R8 SPYDER wheel

.... N
l'­
N "1: .... I.O
"' N
"' ....
What should I be aware of when changing a tire?
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed the
right direction .
A unidirectiona l tire can be ident ified by arrow s
on th e sidewall ,
which point in the di rection of
the rotat ion. You mus t fo llow the spe cified direc­
tion of rotation. This is necessary in order fo r
these tires to develop the ir opt imum characteris ­
tics regarding grip, road noise, wear, and hydro ­
p laning .
Anti-theft wheel bolts
A special adopter is needed to turn the anti-the~
wheel bolts.
2
Fi g. 1 56 A nti-theft wheel bo lts wit h adapter
.. Install the adapter @as far as it w ill go onto
the ant i-theft wheel bolt @ .
.. Pu sh the wheel wrench over the adapter @as
far as it will go .
.. Loosen or tighten the wheel bolt ¢
page 205 .
We re commend a lways keepi ng the wheel bo lt
adapter with yo u in the vehicle . It s hould be s tor ­
ed in the vehicle tool kit.
There is a
c od e number for the w heel bolt lock ing
dev ice, stamped on the face of the adapte r. You
can use th is number to obt ain a repl acement
adapter at a n author ized A udi dealers hip, if nec ­
essary.
What do I do no w?
(D Tips
Write down the wheel bo lt lock ing device
code number and store it in a safe place, away
from the vehicle.
Raising the vehicle
Appl ies to veh icles : w ith or ig inal A udi jack
The vehicle must be li~ed with the jock* first be­
fore the wheel can be removed.
•
F ig. 157 Sill panels: ma rk in gs
Fig. 158 Sill: posit io nin g the ve hicle jack
The descr ipt ion for usi ng the veh icl e jac k only ap­
plies to the or ig inal ja ck* (not a veh icle compo­
nen t; contact your au thor ized A udi dealer if
needed) .
.. App ly th e
parking brake firmly to prevent your
veh icle from rolling unintentionally.
.. Shift to
1 st gear (manual tra nsmission). I n
veh icles with automatic transmissions, make
sure t he a utomat ic parking lock is set as we ll
r:!) page 75.
.. Find the lifting point in the sill on the side with
the affected wheel<=>
fig. 157 .
.. Extend the jack under the lifting point on the
door sill until its arm is positioned directly un-
der the lifti ng po int
r:!) ,&. . ..,_
203

What do I do now?
• Align the jack so that its arm@ c> fig. 158 en­
gages in the designated lifting point in the door
s ill and the movable base @ lies flat on the
ground . The base @ must be
vertical under the
lifting point @.
• Wind the jack up further until the flat tire
comes off the ground
c> ,&. .
Position the vehicle jack only under the designat­
ed lifting points on the sill<=>
fig. 157. There is ex­
actly
one location for each side of the vehicle .
The jack must not be posit ioned at any other lo­
cation
c> .&, c>(D .
An unstable surface under the jack can cause the
vehicle to slip off the jack . Always provide a firm
base for the jack on the ground . If necessary
place a sturdy board or similar support under the
jack. On
hard, slippe ry surfac es (such as tiles)
use a rubber mat or similar to prevent the jack
from slipping
c> .&, .
A WARNING
-
-You or your passengers could be injured
while changing a wheel if you do not follow
sa fety precautions:
- Position the vehicle jack only at the desig­
nated lifting points and align the jack.
Otherwise, the vehicle jack could slip and
cause an injury if it does not have suffi­
cient hold on the vehicle.
- A soft or unstable surface under the jack
may cause the vehicle to slip off the jack .
Always provide a firm base for the jack on
the ground. If necessary, use a sturdy
board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipping.
- To help prevent injury to yourself and your
passengers:
- Do not raise the vehicle until you are sure
the jack is securely engaged.
- Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
204
- Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack.
(D Note
A floor jack or the pads on the hoist arms
must
not be positioned at the points shown
-arrow-.
Removing the wheel
Follow these instructions step-by-step for chang­
ing the wheel.
Fig. 159 Whee l chan ge: using the screwd river handle (wit h
the blade removed) to turn t he bolts
Fig. 160 Whee l chan ge: alignme nt pin inside the top hole
After you have loosened all wheel bolts and
raised the vehicle off the ground, perform the
following steps to remove and replace the wheel:
Removing the wheel
• Use the hexagonal socket in the screwdriver
handle
to completely turn out the topmost
wheel bolt and set it aside on a
clean surface .
• Screw the threaded end of the
alignment pin
from the tool kit hand-tight into the now va­
cant bolt hole<=>
fig. 160.

..... N
r-­N "': ..... \!) 1.1'1
N 1.1'1 .....
~ Then comp lete ly unscrew th e othe r whee l bolts
as descr ibed above.
~ Takeoff the wheel le aving the alignment pin in
t he bolt hole
Q (D.
Putting on th e w hee l
~ Lift the spare wheel and carefully slide it over
the alignment pin to guide it in place
q (D.
~ Use the hexagonal socket in the screwdriv er
hand le to screw in and tighten all wheel bo lts
s ligh tly.
~ Unscrew the alignmen t pin and insert and
t ighten the remaining wheel bolt s light ly like
the rest .
~ Turn the jack handle counter-clockw ise to lowe r
the vehi cle until the jack is fu lly released.
The wheel bolts must be clean and turn easily. Check the contact surfaces of wheel and hub . Re­
move contaminants on these surfaces before in­
stall ing the wheel.
The hexagonal socket in the screwdriver handle makes it eas ier to hand le the wheel bolts . The re­
ve rsible blade shou ld be removed .
When mounting
un idirectional tires, observe the
d irection of rotation
q page 203 .
When removing or install ing the wheel, the
r im could hit the brake rotor/ceramic brake
roto r* and damage the rotor. Wo rk ca refully
an have a second pe rson help you .
{D) Tips
Never use the hexagonal socket in the handle
of t he screwdr iver to loose n or tighten the
wheel bo lts.
Tightening wheel bolts
~ Fi t the wheel bolt wrench ove r th e wheel bo lt
and push it down as fa r as it will go
l).
~ Close your grip aro und the end of the wrench
hand le for max im um torq ue and turn eac h
whee l bolt
cloc kwi se u ntil it s its t ight .
l) You need t he appro pria te adapte r to t ight en th e an ti- th eft
wheel bo lts
<=:> p age 20 3.
What do I d o now?
Have the tightening torque of the wheel bolts
checked as soon as possib le with a torqu e
w renc h. It should be 120 Nm .
Check the
tire pre ssure as soon as possible.
Return the veh icle tool k it to its p roper place .
A WARNING
Loosening the whee l bolts is p roh ibited; dan­
ger of an accident!
(D Tips
- Never try and use the hexagonal socket in
the handle of the screwdrive r to loosen o r
tighten t he whee l bolts.
- If you hav e determined that wheel bolts are
co rroded and difficult to turn, the bolts
must be replaced before checki ng t he tor­
que.
- Unt il the t ightening to rque is checked, d rive
a t redu ced s peed s as a precaution.
Notes on wheel change
Please read t he info rmation q page 186, New
tires and replacing tires and wheels,
if yo u are
going to us e a spare tire w hich is different from
the ti res on your vehicle.
After you change a tire:
- Che ck the tire pre ssure on the spar e imm ed i­
ate ly after mounting .
- Have the wheel bolt tightening torque
c he cked with a torque wrench as soon as po s­
s ible by your authorized Audi d ealer or a
qualified service station .
- With steel and all oy wheel rim s, th e wheel
bolts ar e corre ctl y tightened at a torque of 90
ft lb
( 120 Nm ).
- If you noti ce while changing a tire that the
wheel bolts are corroded and diffi cult to turn ,
then the y should be replaced before you check
the tightening to rque .
IJ>-
205

What do I do now?
-Repl ace th e fl at ti re with a n ew one and h ave
it ins talled on you r vehicle as soon as
po ssible. Remount the wheel co ve r.
Until th en, driv e with extr a car e and at redu ced
s pe eds .
A WARNING
-If you are go ing to equip your vehicle with
t ires or rims which differ from those wh ich
were factory installed, then be sure to read
the informat ion¢
page 186, New tires and
replacing tires and wheels.
- Always store the tools securely in luggage
compartment . Otherwise, in an accident or
sudden maneuver they cou ld fly forward,
caus ing injury to passengers i n the vehicle .
(D Note
Do not use commercially available t ire sea l­
ants. Otherwise, the electrical components of
the t ire pressure monito ring system* will no
longer wo rk properly and the sensor fo r the
tire pressure monitor ing system will have to
be rep laced by a qualified workshop.
Jump-starting
General
If necessary, the engine can be started by con­
necting it to the battery of another vehicle.
-
If the engine sho uld fail to start because of a d is­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, using a
pai r of jumpe r cable s to start the engine.
Both batteries must be rated at 12 vo lts. The
ca ­
pacit y
(Ah) of the booster battery must not be
substantially less than the capacity of the dis­
charged battery.
Jump er c ables
Use only jumper cables of sufficiently large cro ss
s e ctio n
to safely carry the s tarte r cu rrent . Refer
to the manufact urer's specifications.
Use o nly jumper cables wh ich have
insulated ter­
minal clamps and are p roperly marked for d is­
tinction:
206
plu s(+) ca ble : in most cases colo red red
minu s(-) c abl e:
in most cases colo red bla ck
A WARNING
-
Batteries conta in e lectr ic ity, acid, and gas.
Any of these can cause very serious or fata l in ­
jury . Follow the instructions below for sa fe
handling of your vehicle's battery.
- Always shie ld your eyes and avoid leaning
over the battery whenever possib le .
- A discharged battery can a lready freeze at
tempera tures just below 32 °F (0 °C). Befo re
connecting a jumper cab le, the frozen bat­
tery must be thawed comp lete ly, otherwise
it could exp lode.
- Do not allow battery acid to contact eyes or
skin . Flush any contacted area with water
immed iately.
- Improper use of a booster battery to start a
veh icle may cause an explosion.
- Vehicle batter ies generate explosive gases .
Keep sparks, f lame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery.
- The voltage of the booster battery must al­
so have a 12 -Vo lt rat ing. The capacity (Ah)
of the booster battery should not be lower
than that of the discharged battery. Use of batter ies of different voltage or substantial­
ly different "Ah" rating may cause an explo­
sion and personal injury.
- Never charge a frozen battery. Gas trapped
in the ice may cause an exp losion .
- Never charge or use a battery that has been frozen. The battery case may have be weak­
ened.
- Use of batter ies of different voltage or sub­
stantially d iffe rent capacity (Ah) rating may
cause an exp losion and injury. The capacity
(Ah) of the booster battery sho uld not be
lower than that of the discharged battery.
- Before you check anything in the engine
compa rtment, always re ad and heed all
WARNINGS
¢page 155, Working in the en -
gine comportment. .,,.

What do I do now?
- Be fo re you check a nything in t he e ngine
compartment, always read and heed all
WARNINGS
Q page 155, Working in the en­
gine compartment .
CD Note
Improper hook-up of jumper cables can ruin
the generator.
- Always connect POSITIVE( +) to POSITIVE
( + ), and NEGA TIVE(-) to NEGATIV E(-)
gro und post of the battery manager control
unit.
- Check that a ll screw plugs on the battery
cells are screwed in firmly . If not, tighten
plugs prior to connect ing clamp on negat ive
battery terminal.
- Please note that the procedure for connect­
i ng a jumper cable as described above ap­
plies specifically to the case of your vehicle
being jump started. When you a re g iving a
ju mp sta rt to another vehicle, do
not con­
n e ct the neg ative(- ) ca b le to the negative
( - ) terminal o n the discharged battery @.
Instead, se curely connect the negative(-)
cab le to either a solid metal component
that is f irm ly bolted to the engine block or
to the engine block itself . If the battery that
i s bei ng charged does not vent to the out­
s ide , escap ing battery gas could ignite and
explode!
Emergency towing with
commercial tow truck
General hints
Your Audi requires special handling for towing.
The fo llow ing in formation is to be used by com ­
mercial tow truck operators who know how to op ­
erate their equipment safely .
- Never tow your A ud i, tow ing will cause damage
to the engine and transmiss ion .
- Never wrap the safety chains o r winch cables
around the b rake lines.
- To preven t un ne cessary d am age, yo ur Audi
mus t be transpor ted with a car carrier ( flat bed
t ruck) .
208
-To load the vehicle on to the flat bed , use the
tow ing loop found in the vehicle tools and at­
tach to the front anchorage
Q page 208.
_& WARNING
A veh icle being towed is not safe for passen­
gers. Never a llow anyone to ride in a vehicle
being towed, fo r any reason.
CD Note
The vehicle has ver y low ground clearance.
M ake sure that no damage is caused to the
underside of the vehicle when it is being load­
ed onto a flat bed truck .
Front towing loop
Do not install the front towing loop un til it is
needed.
Fi g. 163 Righ t fro nt bu m per w it h ou t gr ille: Tow ing loo p
full y screwe d in
On the right front in the bumper , there is a
t h readed hole behind the air intake g rill into
which the tow ing loop is screwed .
.,. Remove the tow ing loop from the vehicle tool
kit
Q page 199 .
.,. Pull the lower part of the gr ill forward a nd out .
.,. Sc rew the tow ing loop t ightly into t he threaded
hol e as fa r as it will go
Q fig . 163 and tighten it
w ith the wheel w rench .
When it is no longer needed, unscrew the towing
l oop and put it back into the on-boa rd too lkit .
Make sure to have th e towing loop sto red in the
vehicle at all times .
When install ing the grill for the air duct, be sure
that the tabs on t he g rill a re first inserted into .,..

Fuses and bulbs
Fuses and bulbs
Electrical fuses
Replacing fuses
Fuses that have blown will have metal strips
that have burned through .
Fig. 164 Passenger's s ide wheel well: Foot rest with fuse
arrangement
The fuses are located in the footwell area on the
passenger's side behind a cover .
.. Switch the ignition and all e lectrica l equipment
off .
.. Check the following table to see which fuse be-
longs to the equipment .
.,. Remove the floor mat .
.,. Fo ld the foot rest back~
fig. 164 .
.,. Remove the clamp from the holder in the fuse
box .
.. Remove the fuse using the clamp and replace
the b lown fu se with an ident ica l new one .
.. Fo ld the foot rest down again .
Fuse color identification
Color Current in amps
B lack 1
Purple 3
Light b rown 5
Brown 7 .5
Red 10
B lue 15
Yellow 20
Whit e or transparent 25
Green 30
Ora nge 40
210
A WARNING
Do not repa ir fuses and never replace a blown
f u se w ith one that has a highe r amp rating.
This can cause damage to the electr ica l sys­
t e m and a fire.
(D Note
If a new fuse blows again shortly after you
have installed it, have the electrical system
checked by an a uth orized Audi dea le r or a u­
thoriz ed Audi Serv ice Facility .
@ Tips
-The followi ng table does not list fuse loca­
t ions that are not used .
- Some of the equipment listed in the fo llow­
ing tables applies on ly to certa in model ver­
sions or certa in optiona l equipment .
Fuse assignment
Fig. 165 Pas senge r footwell: Fuse panel
Fuse panel @
No . Consumer
1 VOA interface
2 Heated windshield washer nozzle

Consumer Information
scope of maintenance and repairs which can be
carried out by vehicle owners .
Also , sa fety and
en vironment al
concerns place very str ict limits
on the nature of repa irs and adjustments to en­
g ine and transmission parts which an owner can
perform .
Maintenance, adjustments and repairs usually re­
qu ire spec ia l tools, testing devices and other
equ ipment available to specially tra ined work­
shop personnel in order to assure proper per­
formance, reliab ility and safety of the vehicle and
its many systems .
Improper maintenance, adjustments and repairs
can impair the operation and reliability of your
veh icle and eve n void your vehicle warranty .
Therefore, proof of servicing in acco rdance with
the ma intenance sched ule may be a condition fo r
upho ld ing a possible wa rranty claim made w ith in
the wa rranty per iod .
Above all, operational safety can be adversely af­
fected, creating unnecessary risks fo r you and
your p assengers .
If in doubt about any se rv ici ng, have it done by
your author ized Audi dealer or any other properly
equ ipped and qualified workshop. We st ro ngly
urge you to give yo ur au thori zed Audi dealer the
opport unity to perform all schedu led mainte­
nance and necessary repairs. Your dealer has the
facilities, original parts and trained specialists to
keep yo ur vehicle runn ing proper ly.
Performing limited mainten ance yourself
The fo llow ing pages describe a lim ited number o f
p roced ures which can be performed on you r vehi­
cle with ordinary tools, sho uld the need a rise and
trained personne l be unavailab le. Before per­
forming any of these procedures, always thor­
oughly read all of the applicable text and careful­
ly follow the instructions g iven. A lways rigorously
observe the
WARNINGS prov ided .
Before you check anything in the engine com ­
partment , always read and heed all WARNINGS
c> & and c> & in Working in the engine compart­
ment on page 155.
216
A WARNING
-
-Ser ious personal in jury may occur as a result
of improperly performed maintenance, ad­
justments o r repai rs.
- Always be extremely careful when work ing
on the vehicle . Always follow commonly ac­
cepted safety pract ices and general com­
mo n sense. Never r is k pe rsonal i njury.
- Do not attempt any of the mainte nance,
checks or repairs described on the following
pages if you a re not fully familiar with these
or other procedures w it h respect to the ve hi­
cle, or are unce rtain how to proceed .
- Do not do any work wi thout the proper tools
an d eq uipment. H ave the necessary work
done by your au thorized Audi dealer o r an ­
other prope rly equippe d an d qua lified work­
shop .
- Always remove the ignition key befo re any ­
one gets under the vehicle.
- Always support your veh icle with safety
stands if it is necessary to work underneath
the vehicle. The jack * is not adequate for
this purpose and co uld collapse causing se­
r ious personal in jury.
- If you must wor k unde rneath the vehicle
w it h the wheels on t he gro und, a lways make
sure the vehicle is on level ground, that the
wheels are a lways securely blocked and that
the engine cannot be started .
- Always make sure the transmission selector
lever is in "N" (N eutral) (5 tronic) or Neutral
(ma nual transm iss ion) and the hand brake is
fi rm ly applied.
@ For the sake of the environment
- Cha ng ing the engine settings will adve rsely
affect emiss ion levels. This is detrimental to
the environment a nd increases fuel con­
s u mption.
- Always observe environmenta l reg ulations
when dispos ing of old engine oil, used brake
fluid, dirty eng ine coolan t, spent ba tter ies
or worn ou t tires.

..... N
r-­N "': ..... \!) 1.1'1
N 1.1'1 .....
A
A/C operation . . . . . . . . . . . . . . . . . . . . . . . . . 65
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Active rollover protection system . . . . . . . . . 93
Retracting rollover protection . . . . . . . . . . . 94
Adding Engine coolant . . . . . . . . . . . . . . . . . . . . . . 163
Engine oil . . . . . . . . . . . . . . . . . . . . . . 160, 161
Addit ional accessories . . . . . . . . . . . . . . . . . 217
Additives . . . . . . . . . . . . . . . . . . . . . . . . 160, 161
Adjustab le steering column . . . . . . . . . . . . . . 66
Adjusting front seats . . . . . . . . . . . . . . . . . . . 56
Advanced Airbag System Children . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Components . . . . . . . . . . . . . . . . . . . . . . . . 108
Front airbags . . . . . . . . . . . . . . . . . . . . . . . 106
How the components work together . . . . 110
Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . 112
Weight-sens ing mat . . . . . . . . . . . . . . . . . 123
Airbag Warn ing/indicator lights . . . . . . . . . . . . . . . 13
Airbag system ................ ... . 102, 119
Care.. ..... .. ................ ..... . 114
Child restraints. . . . . . . . . . . . . . . . . . . . . . 124
Components (front airbags) . . . . . . . . . . . 108
Danger of fitting a child safety seat on the
front passenger seat . . . . . . . . . . . . . . . . . 103
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Front airbags . . . . . . . . . . . . . . . . . . . . . . . 106
H ow do the front airbags work? . . . . . . . . 110
H ow many airbags does my vehicle have? 108
Important safety instruc tions on the knee
airbag system............... ... .... . 118
Important things to know . . . . . . . . . . . . . 102
Indicator light . . . . . . . . . . . . . . . . . . . . . . 112
Knee airbags ........................ 116
Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . 112
PASSENGER AIR BAG OFF light . . . . . . . . . 112
Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Side airbags . . . . . . . . . . . . . . . . . . . . . . . . 118
When must the system be inspected? . . . 112
Air cond itionin g
A/C operation . . . . . . . . . . . . . . . . . . . . . . . . 65
Air distribution . . . . . . . . . . . . . . . . . . . . . . . 63
A ir recirculation mode . . . . . . . . . . . . . . . . . 64
Automatic mode . . . . . . . . . . . . . . . . . . . . . 64
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Index
Defrost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Economical use . . . . . . . . . . . . . . . . . . . . . . 65
Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Rear window defogger . . . . . . . . . . . . . . . . . 64
Switching on and off . . . . . . . . . . . . . . . . . . 62
Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 62
Air distribution . . . . . . . . . . . . . . . . . . . . . . . . 63
Air recirculation mode
Air conditioning . . . . . . . . . . . . . . . . . . . . . . 64
Alcantara Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
All-wheel drive . . . . . . . . . . . . . . . . . . . . . . . 139
Winter tires . . . . . . . . . . . . . . . . . . . . . . . . 193
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Anti-freeze
refer to Engine coolant system . . . . . . . . . 161
Anti- lock brake system
Warning/indicator lights . . . . . . . . . . . . . . . 15
Anti-lock braking system . . . . . . . . . . . . . . . 134
Anti-slip regulation . . . . . . . . . . . . . . . . . . . 134
Anti-theft alarm system . . . . . . . . . . . . . . . . . 33
Anti-theft wheel bolts . . . . . . . . . . . . . . . . . 203
Ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Asterisk What does it mean when something is
marked with an asterisk? . . . . . . . . . . . . . . . . 5
Audi magnet ic r ide . . . . . . . . . . . . . . . . . . 18, 72
Description . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Indicator light . . . . . . . . . . . . . . . . . . . . . . . 18
Audi Serv ice Repair Manuals and Literature 215
Automatic be lt retractor . . . . . . . . . . . . . . . . 98
Automatic headlight . . . . . . . . . . . . . . . . . . . 46
Automatic transmission . . . . . . . . . . . . . . . . . 75
also refer to S tronic (Automatic transmis-
s ion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Automatic transmission (S tronic) Parking lock emergency release . . . . . . . . . 79
Automatic transmission (tiptron ic)
Emergency mode . . . . . . . . . . . . . . . . . . . . . 78
Auto Safety Hotline . . . . . . . . . . . . . . . . . . . . 92
Average fuel mileage . . . . . . . . . . . . . . . . . . . 21
Average speed . . . . . . . . . . . . . . . . . . . . . . . . . 21
Avoid damaging the vehicle . . . . . . . . . . . . . 142
219