2015 AUDI R8 SPYDER stop start

Parking system
Parallel parking
Applies to vehicles: with parking system advanced
Use parking mode 2 to help you parallel park
along the side of a street.
Fig . 97 Na vigation system d isplay : Blue sur face aligned
wit h parking spot
0
-
Fig. 98 Navigatio n system display: The blue cu rved line
contacting the curb
The following steps app ly only when there is no
obstacle such as a wall near the parking spot.
Otherwise, please read the information provided
in the "Parking Next to Obstacles" section .
• Activate the turn signal.
• Position your vehicle parallel to the edge of the
street, approximately 3 ft . (1 m) from a parked
vehicle.
" Switch the navigation system and the naviga­
tion system display on .
• Se lect reverse gear. The parking aid t urns on
and parki ng mode 1 appears on the display.
• Press the control button
1 on the navigat ion
system
9fig . 97. Parking mode 2 appears.
•B ackup and align your vehicle so the blue area
@ borde rs on the rear end of the vehicle or on
the parking spot line. The blue area represents
an extension of the vehicle's outline by approxi­
mately 16 ft (5 meters) to the rear. The long
84
side o f the b lue area should be on the curb . The
entire blue area must fit into the parking spot .
"W ith the vehicle stopped, turn the steering
wheel to the right as far as it will go.
• Back into the parking spot until the blue curve
touches the curb
9 fig . 98. Stop the veh icle .
" With the vehicle stopped, turn the steering
wheel to the left as far as it wi ll go .
• Con tinue to back into the parking spot until the
veh icle is parked parallel to the curb .@ marks
the rear bumper. Stop the vehicle when the red
orientation line@ borders an object
9 ,&.
Keep an eye on the front of yo ur vehicle while
doing this
c> (D.
Parking next to obstacles
When there is an obstacle (such as a wall) next to
the parking spot, choose a spot with more space
on the sides . Position the long side of the blue
area so that there is sufficient space from the
curb. The area must not be on the curb . You will
also need to start turning the steering wheel
much earlier. There should be a sufficient amoun t
of space between the curb and the blue curve,
and the blue curve¢
fig. 98 must not touch the
cu rb.
_& WARNING
- The rearview camera does not show the en­
tire area behind the vehicle
c> page 80,
fig .
92. Watch out especially for small chil­
dren and animals. Th e rear view camera can­
not a lways detect them, posing risk of an
accident!
- Please note that objects not touching the
ground can appear to be farther away than
they really are (for example, the bumper of
a vehicle or the rear of a truck). In this case,
you should not use the orientation lines to
he lp with parking, wh ich poses danger of an
accident!
(D Note
In the navigation system disp lay, the direction
of travel of the vehicle rear is represented de­
pending on the steering wheel angle. The ve­
hicl e front swings out more than the vehicle
rear . Maintain plenty of distance so that your
lllJ,,

Driving Sa fel y
-never rest you r feet on the seat cushion or back
of the seat
- never ride in the footwell
- never ride in the cargo area
_& WARNING
Imprope r seating positions increase the risk
o f serious personal injury and death whenever
a vehicle is being used .
- Sitting incor rectly places occ upants at risk
of being critically in jured if the airbags de­
ploy and str ike them.
- Be fore you start dr iv ing, seat yourself prop­
erly and always maintain this seating posi­
t ion during the trip . Before each trip, in­
struct your passengers to seat themselves
properly and to maintain this seating posi­
t ion during the trip
c> page 56 , General rec­
ommendations .
Driver and passenger
side footwell
Important safety instructions
_& WARNING
Always make su re that the knee a irbag can in­
flate wi thout interferen ce. Ob je cts betwee n
yourself and the airbag can increase the risk
of injury in an accident by interfering with the
way the airbag deploys or by being pushed in­
to you as the airbag deploys.
- No persons (chi ld ren) or animals should ride
in the footwe ll in front of the passenger
seat. If the airbag dep loys, this can res ult in
serious or fatal in ju ries.
- No objects of any kind shou ld be carried in
the footwell area in front of the driver's or passenger's seat. Bulky objects (shopp ing
bags, for example) can hamper or p revent
proper deployment of the airbag . Small ob­
jects can be th rown t hrough the ve hicle if
the ai rbag deploys and injure you o r you r
passengers.
90
Pedal area
' Pedals
T he pedals must always be free to move and
must never be interfered with by a floor mat or
any other object.
Make sure that all peda ls move free ly without in­
terference and that nothing prevents them from
r et urning to the ir origi nal positions .
Only use floor mats that leave the pedal area free
and can be secured with floor mat fas teners.
If a brake circ uit fai ls, increased brake pedal trav ­
el is required to bring the vehicle to a full stop .
_& WARNING
Pedals that cannot move freely can cause loss
of vehicle control and increase the risk of ser i­
ous injury .
- Never p lace any objects in the driver's foot­
wel l. An object could get into the pedal area
and i nterfere with pedal function. In case of
sudden b raking o r an accident, you would
not be able to b rake or ac celerate!
- Always ma ke sure that no thing can fall or
move into the d river's footwel l.
Floor mats on the driver side
Always use floor mats that can be securely at­
tached to the floor mat fasteners and do not in ­
terfere with the free movement of the pedals.
.. Make sure that the floor mats are properly se­
cured and cannot move and interfere with the
pedals
c> ,&. .
Use only floor mats that leave the pedal area un­
obstructed a nd that are firmly secured so that
they cannot s lip out of position . You can obta in
su itab le floor mats from your authorized Audi
Dealer .
Floor mat fasteners are insta lled in your Audi.
Floor mats used in yo ur vehicle must be attached
to these fasteners. Properly sec uring the floor ..,_

.....
Vehicle care and cleaning General information
Regular, proper care helps to maintain your vehi ­
cle's value.
It can a lso be a req uirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The required cleaning and care products can be
obtained from your authorized Audi dea ler or a
qualified workshop. Read and follow the instruc­
tions for use on the packaging.
A WARNING
-Us ing clean ing and care products incorrectly
can be dangerous to your health.
- Always store cleaning and care products out
of reach of children to reduce the r isk of poi­
soning.
@ For the sake of the environment
- Preferably use environmentally-friendly products when buying cleaning agents.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer deposits remain on the vehicle, the
more the surface can be damaged. High tempera­
tures such as those caused by sunlight increase
the damaging effect .
Before washing, wet heavy deposits with plenty
of water.
Stubborn depos its such as bird droppings or tree
sap are best removed with plenty of water and a
microfiber cloth .
A lso, was h the underside of your vehicle once
road salt stops being used for the season.
Pressure washers
When washing your veh icles w ith a pressure
washer, always follow the operating instructions
"' provided with the pressure washer. This is espe-
r--
~ cially important in regard to the pressure and
; spraying distance . Do not aim the spray directly
~ at seals on side windows, doors, the engine com -,.... Vehicle care and cleaning
partment lid, the front lid
or the convertible top
or at tires, rubber hoses, insulating material
orsensors* or camera lenses *. Keep a distance of
at least 16 inches (40 cm).
Do not remove snow and ice with a pressure
washer .
Never use rotary nozzles or high pressure noz­
zles.
The water temperature must not be above 140 °F
(60 °().
Automatic car washes
Spray off the veh icle before washing.
Make sure that the windows are closed and the
windshield wipers are off. Follow instructions
from the car wash operator, especially if there are
accessor ies attached to your vehicle .
If possible, use car washes that do not have
brushes .
Only use car washes where the vehicle remains
stationary and the washing equipment moves
around t he vehic le when washing and drying. Car
washes that move the vehicle through the car
wash using a chain are not recommended.
Washing by hand
Clean the vehicle starting from the top and work­
ing down using a soft sponge or cleaning brush.
Use solvent-free cleaning prod ucts .
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large particles from your vehi ­
cle. Insects, grease spots and fingerprints are
best removed with a spec ia l cleaner for matte
finish paint.
Apply the prod uct using a microfiber cloth . To
avo id damaging the paint surface, do not use too
much pressure.
Rinse the vehicle thoroughly with water. Then
c lean using a neutral shampoo and a soft micro­
fiber cloth.
Rinse the vehi cle thoroughly again and let it air
dry. Remove any water residue using a sham my . .,.
145

.... N
" N ": ... IO "? N U'> .....
-Place the air pressure gauge on the valve .
- The tire pressu res should only be
checked an d adjusted when the
t ires are cold. The slig htly raised
pressures of warm tires must
not be reduced .
- Adjust the tire pressure to the
load you are carrying.
-Reinstall the valve stem cap on the valve .
When should I check the tire
pressu re?
The correct tire pressure is espe­
cially important at high speeds .
The pressure should therefore be
checked at least once a month
and always before starting a jour­
ney.
When should I adjust the tire pressures ?
Adjust the tire pressure to the
load you are carrying . After
changing a wheel
or replacing
wheels you have to adjust the tire pressures on all wheels. In addi ­
tion, you must then initialize the
new tire pressures in the tire pres­
sure mon itoring system
¢page 196 .
Tires and wheels
A WARNING
Incorrect tire pressures and/or
underinflation can lead sudden
tire failure, loss of control, col­ lision, serio us personal injury or
even death .
-When the warning symbol
rD]
appears in the instrument
cluster, stop and inspect the
tires.
- Incorrect tire pressure and/or
underinflation can cause in­
creased tire wear and can af ­
fect the handling of the vehi­
cle and stopping ab ility.
- Incorrect tire pressures and/or
underinflation can also lead to
sudden tire failure, including a
blowout and sudden deflation,
causing loss of vehicle control.
- The driver is responsib le for
the correct tire pressures for
all t ires on the vehicle . The ap ­
plicable pressure values are lo­
cated on a sticker on the driv ­
er's side B-pillar.
-Only when all tires on the ve­ hicle are filled to the correct
pressure, the tire pressure monitoring system can work
correct ly .
1 8 1
..

subsequent vehicle start-ups as long as the mal­
function exists.
When the malfunction indicator is illuminated,
the system may not be able to detect or signa l
l ow tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of rep lacement or a lternate tires or
wheels on the vehicle that prevent the TPMS from functioning properly. Always check the
T PMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly .
Introduction
The tire pressure monitoring system monitors air
pressure in all four road wheels while the vehicle
is moving.
As soon as the tire pressure monitoring system
senses a s ignificant loss of a ir pressure in one or
several tires, text messages and ye llow symbo ls
appear in the instrument cluster display to a le rt
the driver. The
[I] warning light in the instru ­
ment cluster comes on when the tire is signifi ­
cantly underinflated .
The warning
light [l'J also illuminates in the case
of a system malfunction.
Be aware that tire p ressure is also dependent on
the temperat ure of the t ire. For every 18 ° F
(10 °() increase in tire temperature, tire pressure
increases by about 1.5 psi (0.1 bar) . The tire
warms up while the vehicle is moving and tire
pressure rises. So you shou ld adjust tire pressure
only when they are
cold, when the temperature
of the tires is roughly the same as the ambient
air temperature.
In order to keep the tire pressure monitoring sys­
tem properly calibrated, tire pressure on all four
tires should be checked at regular intervals .
The tire pressure is shown on the label located on
~ the driver 's side B-pillar (visible when the door is r--
~ open) .
,...., \!) ..,.,
N
"' ,....,
Tires a nd w hee ls
A WARNING
-
When the tire pressure monitoring system
warning light is lit, one or more of your tires is
significantly under- inflated . You should stop
and check your t ires as soon as poss ible, and
i nflate them to the proper pressure as indicat­
ed on the vehicle 's t ire pressure label
¢ page 176. Driving on a significant ly under­
inflated tire causes the tire to overheat and
can lead to tire failure. Under-inflation also is
likely to impair the vehicle's handling and
stopping ability.
@ For the sake of the environment
Driving with under -inflated tires reduces fuel
efficiency and tire tread life.
(D Tips
- Each tire should be checked monthly when
the temperature of the tires is about the
same as ambient air temperature and set to
the recommended inflation pressure as
specified on the tire pressure label
¢page 176.
- The tire pressure mon itoring system helps
the driver to keep an eye on tire pressures.
But the driver still has the responsib ility for
ma inta ining the correct tire pressure.
- Tire pressure must only be adjusted when
the temperature of the tires is about the
same as amb ient air temperature.
- When tires are replaced, the sensors and
valves should not be exchanged. The valve
core, nut, valve seal ing and seal washer (re­
placement kit) needs to be replaced. If nec­
essary, the valve and the wheel electronics
have to be replaced.
- The tire pressure mon itoring system on your
Audi was calibrated using tires with "RO"
identification. We recommend using these
tires .
- If you sho uld put different wheels and tires
on your vehicle (e .g. winter whee ls and
tires), you must be certain that the wheels
197

What do I do now?
Inflating tire
.,. Move the switch @¢ fig. 155 on the e lec tric air
pump
ll to posit io n I. After 5 minutes, tire
pressure must have reached at least 1.8 bar.
.,. Switc h the electric a ir pump off -switch in posi­
tion
0 . If the requ ired tire press ure of at least
1.8 bar has not been reached, follow the in­
structions in the section
Re-inflating tire.
Re-inflating tire
.,. Remove the hose from the va lve and p ull the
pl ug out of the soc ket .
.,. Drive the vehicle s low ly 10 meters backward or
forward. This helps to distribute the sea lant
better .
.,. Remove the empty inflat ion bott le and screw
t h e hose ®¢
fig. 154 from the electric p ump
direc tly onto the
valve .
.,. Inse rt the plug @ into the socket for the c iga­
r e tte lighter .
.,. Swi tc h on the igni tion .
.,. Move t he sw itch @¢
fig. 155 on the e lectric air
pump
ll to posit ion I. After 5 minutes, tire
pressure must have reached at least 1.8 bar .
.,. Switc h the electric a ir pump off -switch in posi­
tion
0 . If the requ ired t ire p ressure of at least
1.8 bar has not been reached, it is not poss ible
to mak e a re pair w it h t he tir e se alant. Seek p ro­
fessional assis tance.
Disassembling Tire Mobility System
.,. Remove the hose from the valve and pu ll the
pl ug out of the socket .
.,. Screw the dust cap onto the
valve .
.,. Place the em pty sealant bottle bac k in the o rig ­
i nal pa cka ging and clip it in pla ce u nder the
f loo r so t hat no ti re se alant c an run o ut into the
vehicle.
.,. Start d riving r ight away so t hat the sea lant is
dist ributed in the tire .
1
> T h e e le ctr ic air pu m p sh o ul d never r un for long er than 6
m in utes .
202
A WARNING ,_ -
- Follow the manufacturer's safety instruc­
tions on the decal for the air pump and the
sealant bottl e .
- If a tire pressure of 1.8 bar cannot beach­
ieved after pumping for S minutes, the t ire
is too severely damaged . Do not con tinue to
d rive .
- Seek pro fessional ass istance if it is not pos­
sib le to r epa ir th e tire w ith the t ire sea lant .
(D Tips
- Do not operate the electric air pump for
more than 6 minutes witho ut stopping, oth­
erw ise i t can overhea t. When th e air pum p
ha s cooled dow n, you can con tinu e to use it.
- If sea la nt has escaped, a llow it to dry, then
you can pee l it off .
· Final check
App lies to vehicles: with Tire Mobility System
After driving for a short distance, tire
pressure must be checked
.,. Aft er d riving for about 10 m inutes, stop and
check the tire pressure.
.,. If tire pressure is sti ll at least 1.3 bar, inflate
the t ire to specified pressure (see d rivers side B­
pillar), drive to the next repair shop and have
the t ire and the sealant bottle replaced.
1> Iftire pressure is less than 1.3 bar, the t ire is
too severe ly damaged . Do not continue to
dr ive . Seek professiona l assistance .
A WARNING
If tire pr ess ure is le ss than 1.3 bar afte r driv­
i ng f or 10 minu tes , the tire is to o seve rely
d amaged . Do not cont in ue to drive . Seek pro ­
fess iona l assistance.
{D Tips
A ft er a tire re pa ir, have the sealant bottle re­
pla ced at a dealersh ip. T his restores full f unc­
tion ality to the Tire Mob ility System .

.... N
l'­
N "1: rl I.O
"' N
"' ....
(D Note
-Applying a higher vo ltage booster battery
will cause expensive damage to sensitive electronic components, such as control
units, relays, radio, etc.
- T here m ust be no e lectrica l contact between
the vehicles as otherwise current could al­
ready start to flow as soon as the pos itive
(+) terminals are connected .
@ Tips
-The discharged battery must be properly
con nected to the vehicle's electrical system.
- Switch
off any car phone, or follow the car
phone instruct ions for this situation.
Use of jumper cables
Make sure to connect the jumper coble clomps in
exa ctly the order described below!
F ig . 161 Luggag e comp artm ent: conn ectors fo r a charg er
an d jump start cab les
®
Fig . 162 Jump start using th e batte ry in a not her ve hicl e: A
• Fe male sock et, B • D isch arge
The batte ry is located in the luggage compart­
ment ~
page 166 . The front lid can be opened in
a n emergency
r=;, poge 33.
What do I do no w?
Do not connect the negative cable d irect ly to the
n egat ive terminal on the battery . Connect it to a
jump start pin instead r=;, fig. 161.
Connect the po sitive cable (r e d ) to the
po sitive terminal
1. Connect one end of the red jumper cab le
r=;, fig . 162 (D to th e positive t erminal of dis­
charged battery @.
2. Connect the o ther end of the red jumper ca­
ble to the positive term inal @ofthe booster
battery @.
Conne ct the neg ative c able (bl ack ) to the
neg ativ e terminal
3. Connect one end of the b lack jumper cable @
to the negative term inal of the booster bat­
tery @.
4. Secu re the other end to the jump start pin@
for the d isc harged battery @.
Starting the engine
"'Start the engine of the veh icle provid ing assis ­
tance and allow it to run at idle .
"' Now sta rt the engine of the vehicle with the
d ischa rged ba ttery.
"'I f the engine does not star t: Stop trying afte r
10 seconds and then try again after about 30
seconds .
"' Disconnect the cable while the engine is run-
ning in exact ly
reverse orde r to that described.
T he bat tery is vented to the outside to p reven t
gases from entering the vehicle interior . Make
s u re that th e jumper clamps ar e well connect ed
with their
metal ports in full contact with the
battery terminals.
A WARNING .
To avoid se rious personal injury and damage
to the veh icle , heed all warnings and ins truc­
tions of the jumper cable manufacture r. If in
doubt, call for road service.
- Ju mpe r cables m ust be long eno ugh so that
the vehicles do not touch .
- When connecting jumper cables, make sure
that they can not g et caug ht in any moving
parts in the eng ine compartment. ..,.
207

Index
Eme rgency r elease
Fr ont lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Park ing lock . . . . . . . . . . . . . . . . . . . . . . . . .
79
Eme rgency sta rting . . . . . . . . . . . . . . . . . . . 206
Eme rgency towing . . . . . . . . . . . . . . . . . . . . 208
Energy management . . . . . . . . . . . . . . . . . . 14 0
Batte ry power . . . . . . . . . . . . . . . . . . . . . . 14 1
Driver notification . . . . . . . . . . . . . . . . . . . 141
Eng ine
Coolan t . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16 1
Data . ... .... .. ... .. ..... ... .. .. ... 214
Eng ine compartment lid . . . . . . . . . . . . . .
155
Starting . . . . . . . . . . . . . . . . . . . . . . . . . 66, 67
Stopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Engine compartmen t . . . . . . . . . . . . . . . . . . 15 7
Safety instructions . . . . . . . . . . . . . . . . . . . 155
Engine compa rtment lid
Closing . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 56
Release lever . . . . . . . . . . . . . . . . . . . . . . . 155
Engine coolant system . . . . . . . . . . . . . . . . . 161
Malfunct io n . . . . . . . . . . . . . . . . . . . . . . . . . 14
Temperature ga uge . . . . . . . . . . . . . . . . . . . . 9
En gine oi l . . . . . . . . . . . . . . . . . . . . . . . . . . .
158
Adding .. .. .. .. ............. .. . 160,161
Addit ives. . . . . . . . . . . . . . . . . . . . . . .
160, 161
Checking the eng ine oi l level . . . . . . . 159, 160
Dry s ump lubr ication . . . . . . . . . . . . . . . . . 139
Indications and cond it ions requ iring ext ra
checking . . . . . . . . . . . . . . . . . . . . . . .
159, 160
O il c ons umption . . . . . . . . . . . . . . . . . . . . . 1 58
O il grades . . . . . . . . . . . . . . . . . . . . . . . . . . 15 8
Specification and viscos ity . . . . . . . . . . . . . 158
Temperature disp lay . . . . . . . . . . . . . . . . . . . 8
E ngi ne oi l level . . . . . . . . . . . . . . . . . . . . . . . . 17
Engine oil pressure (malfunction) . . . . . . . . . 14
Engine oi l sensor defective . . . . . . . . . . . . . .
17
Engine speed limitat ion . . . . . . . . . . . . . . . . . 17
E nvironment
Cataly tic converter . . . . . . . . . . . . . . . . . . .
142
Disposing of your vehicle batte ry . . . . . . . 165
Fue l . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Unleaded f uel ..................... .. 15 1
What should I do wi th an old batte ry? . . . 16 5
EPC
refer to Electronic power control . . . . . . . . 16
ESC (Electronic Stabilization Co ntro l)
Warning/indicator lights . . . . . . . . . . . . . . .
15
222
Event Data Recorde r (ED R) . . . . . . . . . . . . . . 134
Exhaust tail pipes Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7
Expansion tank . . . . . . . . . . . . . . . . . . . . . . .
162
Exterior m irrors
Adjusting . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
Dimming . ... .... .. .. .. .. .. .... ... .. . 50
Heating... ...... .. ............... .. . 49
F
Fan ..... .... . .. .. .. .. ... .. ..... ... .. . 62
Faste ning
Boos ter sea ts . . . . . . . . . . . . . . . . . . . . . . .
128
Convertib le child sa fety se ats . . . . . . . . . . 12 7
Infant seats
Flat bed truck
Flat tire 127
208
Changi ng . . . . . . . . . . . . . . . . . . . . . . . . . . 203
Floor mats . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Fo ld ing master key with remo te control . . . . 27
Foot peda ls . . . . . . . . . . . . . . . . . . . . . . . . . . .
90
Fo r the sake of the environment
Gasoline fumes and t he env ironme nt . . . . 153
Letting yo ur eng ine warm up . . . . . . . . . . .
67
Ref ueling . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Front a irbags
Des cription . . . . . . . . . . . . . . . . . . . . . . . . .
106
How they wor k . . . . . . . . . . . . . . . . . . . . . . 110
Frontal collis io ns and the laws of phys ics . . . 96
Front lid
Emergency release . . . . . . . . . . . . . . . . . . . . 33
light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
49
Power locking system . . . . . . . . . . . . . . . . . 32
Trunk escape handle . . . . . . . . . . . . . . . . . 199
Front passenger
refer to Seating position . . . . . . . . . . . . 87, 88
Front seat s . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Child rest rain ts in the fron t seat . . . . . . . . 103
Front towi ng loop . . . . . . . . . . . . . . . . . . . . . 208
Fuel
Additives.. .. .... .. .. .. ......... .. ..
151
B lended gasoline . . . . . . . . . . . . . . . . . . . . 151
Current fuel mileage . . . . . . . . . . . . . . . . . . 21
Filler neck . . . . . . . . . . . . . . . . . . . . . . . . . .
152
Fuel supply too low . . . . . . . . . . . . . . . . . . . 17
Gasoline . . . . . . . . . . . . . . . . . . . . . . . . . . .
151