2015 AUDI Q7 battery

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Always read and heed all WARNING S below
¢ A. and
¢A. in Working on the battery on
page
267.
.,. Turn off the ignit ion and a ll electrical con­
sumers .
.,. Make sure the area is well venti lated when
you charge the battery.
.,. Open the hood ¢
page 256.
.,. Open the red cover on the positive pole
¢ fig . 248 .
.,. Connect the charger connectors accord ing to
the instructions to the
j ump start bolt s.
(Bolts under the red cover= "positive", Bolts
with hex head= "negative") .
.,. Only now pl ug the mains lead for the charg­
ing equipment into the wall outlet and turn
it on ¢
A_.
.,. Make su re the charging rate i s not o ver
30 amp s/14.8 Volt.
.,. When the battery is fully charged: Turn the
charging equ ipment
off and remove the
mai ns lead from the wa ll outlet.
.,. Now remove the clamps for the charging
equipment.
.,. Close the red cove r on the pos it ive po le.
.,. Close the hood¢
page 256.
A discharged battery can freez e at tempera­
t ures of only O
0C. Allow a frozen batte ry to
thaw comp letely before a ttempting to charge
it ¢& . However, we recommend not using a
thawed battery again because the battery cas­
ing can be cracked due to ice formation and
can leak battery acid .
Battery charging (Ma ximum charging rate
o f 30 amp s/14 .8 Volt)
When charging at low voltages (e.g . w ith a
tric kle ch arger ), the battery cables do not
h ave to be d isconnected first. The battery
caps should
not be opened when charging a
battery .
It is not necessary to remove the battery from
the luggage compartment.
Checkin g and fillin g 269
Fast charging th e battery (cha rging rate
ab ove 14 .8 V olt s)
For technical reasons do not use a battery
charger that uses voltage greater than 14.8
Volts to charge your vehicle's battery.
A WARNING
~ -
Charging a battery can be dangerous .
-Always follow the operating instructions
provided by the battery charger manu­
facturer when charg ing your battery .
- Never charge a frozen battery.
It may ex­
plode because of gas trapped in the ice.
Allow a frozen battery to thaw out f irst.
- Do not reuse batteries wh ic h were fro­
zen. The battery hous ing may have
cracked and weakened when t he battery
froze.
- Charge the battery in a well ventilated area. Keep away from open flame or elec­
tr ica l spar k. Do not smoke. Hyd rogen gas
genera ted by the battery is explos ive .
- To reduce the danger of explosion, never
connect or d isconnect c harger cab les
while the charger i s ope rat ing .
- Fast cha rging a batte ry is dange rous and
should only be a ttempted by a compe­
tent techn ic ian wi th the p rope r equip­
men t.
- Battery acid tha t may spi ll dur ing cha rg­
ing should be washe d
off with a solu tion
of wa rm water and baking soda to neu ­
tralize the acid.
([) Note
Never use a fast charger as a booster to
star t the engine. This w ill seriously dam­
age sens it ive e lectronic com ponen ts, s uch
as contro l units, re lays, radio, etc., as well
as the batte ry charger. •
•

2 70 Ch eck ing and filling
Battery replacement
The new battery must have the same specifi­
cations and dimensions as the original equip­
ment battery.
Intelligen t energy management in your veh i­
cle is respons ible for d istributing the e lectr i­
cal en ergy throughout your vehicle
¢ page 228. The intell igent e nergy manage­
ment system w ill keep the eng ine battery
cha rged better then vehicles w ithout this sys­
tem . To make sure the additional e lectrica l en ­
ergy is availab le once again after you have
changed the battery, we recommend that you install batteries of the same type and manu­
facture only (the same as those installed at
the time your vehicle was delivered). Specifi­
cations are listed on the battery hous ing . Your
author ized dealer must code the battery in
the ene rgy management system to enable you
to use the energy management funct ions cor­
rectly after replac ing the battery.
If it is not poss ible to use a battery of this
type, the new battery must have the same ca­
pac ity, voltage (12 volts), amperage , con­
struction and plug seal ing.
When insta lling the battery, make sure the ig­
n it ion and all e lectr ica l consumers a re turned
off.
Q;) Note
Make sure the venti lation hose on the s ide
of the battery is connected, otherwise
fumes or battery ac id can leak o ut.
@ For the sake of the environment
Because of the problem of proper d isposa l
of a battery, we recommend your autho r­
i z ed Audi dealer change the ba tte ry for
you. Bat teries contain s ulfu ric ac id and
lead and must always be disposed of prop ­
erly in compliance with all environmental
reg ulations. Disposing of vehicle batteries
improper ly is very dangerous to the envi­
ronment.
Windshield/headlight
washer container
F ig . 24 9 Eng in e compart ment : cover on t he wi nds hield
and headl ig ht* washe r fluid reservoi r
The washer fluid co nta iner is marked w ith the
symbol Won its cap
¢ fig . 249, ¢page 258,
fig. 242 .
.. Before you check anything in the engine
compartment,
alwa ys read and he ed all
W ARNING S
¢ & in Working in the engine
compartment on page 256 .
.. Lift the fille r cap tongue to add washer flu­
id. You can fi ll the container to the top.
.. Press the cap back onto the fi ller neck afte r
fi lling the container.
You can find the reservo ir
capacity i n the table
in
¢ page 325.
Clean water should be used when filling up . If
poss ible, use soft water to prevent scaling on
the washer jets. A lways add a glass clea ne r
solution (with frost prote ction in the winter).
0 Note
Do not mix engine coolant antifreeze o r
any other additives to fill up the wind­
s hi eld washer rese rvoir.

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Maximum load rating
means the load rating for a tire
at the maximum permissible in­
flation pressure for that tire.
Maximum loaded vehicle
weight
means the sum of:
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity weight, and
(d) Production options weight
Maximum (permissible)
inflation pressure
means the maximum cold infla­
tion pressure to which a tire
may be inflated. Also called
"maximum inflation pressure."
Normal occupant weight
means 150 lbs. (68 kilograms)
times the number of occupants seated in the vehicle up to the
total seating capacity of your
vehicle.
Occupant distribution
means distribution of occu­ pants in a vehicle.
Outer diameter
means the overall diameter of
an inflated new tire.
Tires and wheels 275
Overall width
means the linear distance be­
tween the exteriors of the side­
walls of an inflated tire, includ­ ing elevations due to labeling,
decorations, or protective bands or ribs.
Ply
means a layer of rubber-coated
parallel cords.
Production options weight
means the combined weight of
those installed regular produc­
tion options weighing over 5 lbs. (2 . 3 kg) in excess of those
standard items which they re­
place, not previously consid­
ered in curb weight or accessory
weight, including heavy duty
brakes, ride levelers, roof rack,
heavy duty battery, and special
trim.
Radial ply tire
means a pneumatic tire in
which the ply cords that extend
to the beads are laid at sub­ stantially 90 degrees to the
centerline of the tread.
•
•
'

M N
0 ...J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Emergency situations
General
This chapter is intended for trained emer­
gency crews and working personnel who have the necessary tools and equipment to
perform these operations.
Starting by pushing or
towing
(D Note
Your v ehicl e is e quipped w ith an automatic
tra nsm iss io n. Cons eque ntly, the e ngine
cann ot be started by pus hing o r tow ing.
Starting with jumper
cables
If necessary, the engine can be started by
connecting it to the battery of another vehi­
cle.
If th e engine shou ld fail to start because of a
d ischarged o r weak battery, the battery can be
connected to the battery of
another veh icle,
usi ng a
pair of jumper cables to start the en­
gine .
Jumper c ables
Use only jumper cab les of sufficiently large
cross section to carry the starter cur rent safe­
l y. Refer to the man ufacturer's specifications.
Use only jumper cables with
insulated te rm i­
na l clamps w hich are d istinctly mar ked:
plus(+ ) cable in mos t ca ses co lore d red
minus(-) cable
i n most cases colored black .
A WARNING
Batteries con tai n elec trici ty, a cid, and gas.
Any o f these c an caus e ve ry ser ious or f atal
injury . Foll ow the instruc tions below fo r
safe han dling of your veh icle's battery .
- Alw ays s hield y our eyes and a void le an­
ing over the batte ry w henever possib le .
Emergency situations 31 7
- A discharged battery can freeze at tem­
pe rat ures just below 32 °F (0 °C). Before
connecting a jumpe r cable, you must
thaw the frozen battery c omp lete ly, ot h­
e rwise it could explode.
- Do not allow battery acid to co ntact eyes
or skin . Fl ush any con tacted area wi th
wat er immediately .
- Imp roper use of a booster battery to
s tart a vehicle may cause an ex plosion.
- Vehicle batter ies generate expl osive gas­
es. Keep sparks, flame and lighted c iga­
rettes away from ba tte ries.
- Do not t ry to jump start a ny ve hicle w it h
a low ac id leve l in the battery.
- The voltage of the booste r batte ry m ust
also have a 12-Vo lt rat ing. T he capac ity
(Ah) of the booste r batt ery sho uld not b e
lowe r than that of th e discharged bat­
t ery. Use o f batt eries of d iffe ren t vol tage
or su bstan tia lly differen t "Ah" rat ing
may cause an exp losion and pers onal in­
jury .
- N ever ch arge a fr ozen batt ery. Gas t ra p­
pe d i n the ice may c ause an ex plosion .
- N ev e r ch arge o r use a batt ery th at h as
been fro zen . Th e batte ry case may have
be weake ned.
- U se o f batter ies of di ffere nt vol tage or
substantially differen t ca pa city (Ah) rat ­
i ng may cause an exp losion and injury .
T he ca pa c ity (Ah) of the booster battery
should not be lower than that of the dis­
charged battery.
- Before you check anything in the engine
compa rtment, always read an d heed a ll
WARNINGS¢
page 256.
(D Note
- App lyi ng a hi gher vo ltage booste r ba t­
t ery wi ll cause expens ive damage to sen ­
sit ive e lectronic components, such as
cont ro l units, relays, rad io , etc.
- There must be no electrical c ontact be ­
tween the vehicles as otherw ise current
co uld already start to f low as soon as t he
posi tive(+) terminals a re con nect ed. ..,. •
•

318 Emergency situations
@ Tips
- The discharged battery must be properly
connected to the vehicle's electrical sys­
tem. When jump starting or charging the
battery, never connect the negative
ground cable to the battery negative
post because the battery manager sys­
tem must be able to detect the battery's
state of charge . Always connect the neg­
ative ground cable to the negative
ground post of the battery manager con­
trol unit.
Use of jumper cables
Make sure to connect the jumper coble
clomps in exactly the order described below!
Fig . 272 Engine co mpartment: Conne cto rs fo r jum per
c ables a nd charger
®
Fig. 273 Ju m p sta rt in g w it h the bat te ry of anot her ve ­
h icle : A - b ooster battery, B - discharge d ve hicl e batte ry
The procedure described below for connecting
jumper cables is intended to provide a jump
start for your veh icle .
Vehicle with discharged battery:
.. Turn
off lights and accessories, move lever
of automatic transmission to N (Neutral) or
P (Park) and set parking brake. Connect
POSITIVE(+) to POSITIVE(+)
(red)
.. Open the red cover on the pos itive pole
¢ fig. 272 .
1. Connect one end of the red positive cable
on the jump start bolt
c::;, fig. 2 73@
(Bolts under red cover = "positive") of the
vehicle to be started @.
2. Connect the other end to the positive ter-
mina l@ of the booster battery@.
Connect NEGATIVE (-) to NEGATIVE (-)
(black)
3. Connect one end of the black negative ca­
ble to the negat ive terminal @ of the
booster battery @.
4. Connect the other end of the black nega­
tive cable to the jump start bolt@ (Bolts
with hex head= "negative") of the vehicle
to be started @.
Starting the engine
.. Start the engine of the vehicle w ith the
booster battery@. Run the engine at a
moderate speed .
.. Start engine with discharged vehicle battery
@ in the usual manner.
.. If the engine fails to start: do not keep the
starter crank ing for longer than 10 seconds .
Wait for about 30 seconds and then try
again .
""W ith engine running, remove jumper cables
from both vehicles in the exact
reverse or·
de r .
.. Close the red cover on the positive pole.
T he battery is vented to the outside to prevent
gases from entering the veh icle interior. Make
sure that the jumper clamps are well connect­
ed with their
metal ports in full contact with
the battery terminals.
A WARNING
-
To avoid serious persona l injury and dam-
age to the vehicle, heed all warnings and i nstructions of the jumper cable manufac-
turer . If in doubt, call for road service . ,..

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
-Jumper cables must be long enough so
that the vehicles do not t ouch.
- W hen connecting jumper ca bles, make
sure that they cannot get caught in any
moving parts in the eng ine compart­
ment.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
Q page 256.
(D Note
Improper hook-up of jumper cables can ru­
in the generator.
- Always connect POSITIVE( +) to POSI ­
TIVE(+), and NEGATIVE(-) to NEGATIVE
( - ) ground post of the battery manager
control unit.
- Check that all screw plugs on the battery
cells are screwed in firmly. If not, tighten plugs prior to connecting clamp on nega­
tive battery terminal.
- Please note that the procedure for con­
nect ing a jumper cable as described
above applies spec ifically to the case of
your vehicle be ing jump started . When
you are giving a jump start to another ve­
hi cle, do
not connec t the negat ive (-) ca­
ble to the negat ive( -) term inal on the
discharged battery ©¢
fig. 2 73. In ­
stead, securely connect the negative( -)
cable to e ither a solid metal component
that is firmly bolted to the engine block
or to the engine block itse lf. If the bat­
tery that is being charged does not vent
to the outside, escaping battery gas
could ignite and exp lode!
Em erg en cy si tuation s 319
Emergency towing
with commercial tow
truck
General hints
Your Audi requires special handling for tow­
ing.
T he following information is to be used by
commercial tow t ruck operators who know
how to operate their equipment safely.
- Never tow your Audi , towing will cause
damage to the engine a nd transmi ssion.
- Never wrap th e safet y chain s or winch c a­
ble s around th e brak e lin es.
- To prevent unne ce ss ary dam age, your Aud i
mu st be t ransp orted with a flat bed truck .
- To load th e vehi cle on to the fl at bed, us e
the t owing loop found in the vehicle t ool s
and atta ch to the front or rear anch o rage
¢ page 320 and Qpage 320 .
A WARNING
A vehicle being towed is not safe for pas­
sengers. Never allow anyone to ride in a
vehicle be ing towed, for any reason.
-
•
•

332 Index
Alcantara
C leaning 245
A ll-w heel drive . ........... .... .... . 227
Winter tir es
A lternator 298
Malfunction . . . . . . . . . . . . . . . . . . . . . . . 31
Ambience lighting Lighting profiles .......... .... .... .. 65
Anti -freeze
refer to Engine coo lant system ...... . 262
Anti-lock brake system ..... ... .. .. .. . 223
Warn ing/ indicator lights . . . . . . . . . 16, 18
Anti-slip regulation ........ .. .. .... . 223
Warn ing/ indicator lights ... .. .. .. .. .. 16
Anti-theft systems Anti-theft alarm system . . . . . . . . . . . . . 50
Electronic immobilizer ... .. .. .. .... . . 40
Approach/departure angle . .. .. .. .. .. . 235
Ashtray . .. ... ............ .. .. .. .. .. 89
Asterisk What does it mean when something is
marked with an asterisk? . . . . . . . . . . . . . . 6
Aud i b rak ing guard ....... .. .. .. .. .. . 129
Error messages .... ....... ... .... . 130
Settings . . . . . . . . . . . . . . . . . . . . . . . . . 130
Status messages . . . . . . . . . . . . . . . . . . 130
Switching on and off ...... .. .. .. .. . 130
Aud i Service Repair Man uals and Litera-
ture .. .. .. .. ............. .. .. .... . 326
Auto -Check Control . . . . . . . . . . . . . . . . . . 30
Automatic belt retractor ... ... .. .. ... 177
Automatic mode
F our-zone automatic comfort air condi-
tioning .... ... .. ..... ... .. .. .... . 101
Automatic Shift Lock (ASL) . . . . . . . . . . . 140
Automatic transmission ..... .. .. .... . 139
Automatic Shift Lock (ASL) . .. .. .. .. . 140
Driving .. ................. .. .... . 141
Emergency mode . . . . . . . . . . . . . . . . . . 143
Emergency release ......... ... .. .. . 143
H ill descent contro l ........ ... .. ... 142
I gn ition key safety lock .... .. .. .. .. . 107
Kick-down . . . . . . . . . . . . . . . . . . . . . . . . 143
M anual s hift program ......... .. .. . 1 42
Selector lever ........... ... .. .... . 139
Shift paddles . . . . . . . . . . . . . . . . . . . . . 142 AUTO mode
A/C climate controls ... ..... ... .. .. . 97
Auto Safety Hot line ............. .... 170
Average speed . . . . . . . . . . . . . . . . . . . . . . . 24
Avoid damaging the vehicle .... ... .. .. 232
B
Bass box
Battery .... .. .. .. .. ........... ... .
Battery location .. ................ .
Charg ing ... ... .. .. ... ........... .
Impo rtant warnings when working on
the battery .... .. ............. ... . 30S
266
267
268
267
Jump start ing .. .. ... .......... .. .. 317
Low .. .. .. .... .. ... .. ..... ... .. .. 228
Replacing the battery ... .... ... .. .. 270
State of charge ... .. ... ......... ... 228
Voltage ... .... ................... . 35
Winter operation . ............. .... 266
Working on the battery .. .... ... .. .. 267
Before driving ..... ... .. ..... .... . .. 163
B lended gasoline .. ................ . 248
Booster seats . . . . . . . . . . . . . . . . . . . . . . 211
Brake fluid
Changing the brake fluid ..... ... .. .. 266
Checking the brake fluid level . ... .. .. 265
Reservoir ... .. .. .. .... .... .... ... 265
What is the correct brake fluid level? .. 265
What shou ld I do if the brake fluid warn-
ing light comes on? .... .. ... ... .. .. 265
Brake light Defective . . . . . . . . . . . . . . . . . . . . . . . . . 23
Brake system .... ... .............. .. 265
Anti- lock brake system . . . . . . . . . . . . . . 18
Brake assist system ..... .... ... .. .. 223
Brake booster .... ... .. ..... .... . .. 225
Brake fluid . ..... ... .. ..... ... .. .. 265
Brake fluid specifications for refill and re-
placement .... .. ............. .... 266
Brake pads .. .. .. ..... ........... . 230
General information .............. . 225
How does moisture or road sa lt affect the
brakes? . .. .. .. .. ............. .. .. 225
Malfunction . . . . . . . . . . . . . . . . . . . . . . . 32
Parking brake .. .. ... .......... .. .. 111
Warning/indicator lights ..... ... .. .. . 19
Worn brake pads symbo l . . . . . . . . . . . . . 36

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Doors
Power child saf ety lock . ... .. .. .. .. .. 48
Dr iver information system ... .. .. .. .. .. 2 1
Di gita l speedomete r ...... .. .. .. .. .. 22
D river info rmation messages . . . . . . . . . 30
Open door or rear lid warning . . . . . . . . . 22
Outside temperature display . ... .. .. .. 22
Sound system display .. ... .. .. .. .. .. 21
D river seat
refer to Seat ing pos it ion ... .. .. .. .. . 164
Driver's seat ................. .... ... 75
Driver's seat memory . . . . . . . . . . . . . . . . . 76
Activating remote control key . . . . . . . . . 77
Recall ing a seat posit ion ... .. .. .. .. .. 76
Sto ring a seat position . . . . . . . . . . . . . . . 76
D riving messages . . . . . . . . . . . . . . . . . . . . 30
Driving mode
refer to Adaptive Air Suspe nsion. 157, 1 59
Driving offroad Driving through water ......... ... .. 236
Driving tips .... ........... ... ... .. 235
Rul es of behav io r ............ .. .... 235
S and and m ud ........... .... .. .. . 236
Snow-covered groun d ..... .. .. .. .. .
236
Unpaved roads ........... .... .. ... 23 6
Driving safe ly .......... ...... .... .. 163
Driving through water ... ... .. .. .. .. . 236
D riving t ime . . . . . . . . . . . . . . . . . . . . . . . . 24
Duplicate key . . . . . . . . . . . . . . . . . . . . . . . 38
D ust filter
Climate controls . . . . . . . . . . . . . . . . . . . . 94
E
Easy en try featu re .. ..... ... .. .. .. .. . 10 6
E fficiency program . . . . . . . . . . . . . . . . . . . 26
Fue l economy messages . ...... ... ... 27
M emory levels . . . . . . . . . . . . . . . . . . . . . 25
Othe r equipmen t ......... .. .. .. .. .. 2 7
Electric seat adjustment
refer to Power seat . . . . . . . . . . . . . . . . . 7 5
Electro nic differential lock (EDL) . ... .. . 223
Warn ing/ indicator lights . . . . . . . . . 16, 18
E le ctr onic immobili ze r ...... .. .. .. .. .. 40
Electronic power co ntrol
( E PC) wa rn ing/indicator light ... ... ... 15
Electronic speed limiter . . . . . . . . . . . . . . . 28
Inde x 335
Electronic Stabilization Cont ro l (E SC) ... 223
Hill descent contro l ..... .... ... .. .. 224
•
Offroad mode .. .. .. . .. ... .... ... .. 224 •
Warning/ind icator lights .......... .. . 16
E merge ncy flashe r . . . . . . . . . . . . . . . . . . . 63
Wa rning/ind icator lights ..... ... .. .. . 16
Emergency locking of doors ............ 45
Emergency operation Rear lid . .. .. .. .. .. ............... . 48
Emergency starting . .. .. ..... ... .. .. 317
Emerge ncy towing ... . .. .. .. ... ... .. 319
Energy management ... .. .... ... .. .. 228
Battery power . .. .... ........... .. 229
Driver notification ................. 229
Engine Compartment .... .. . .. .. ..... ... .. 258
Coolant ... .. .... .. . .. .. ..... ... .. 262
Data ..... .. .. .. ... ............ .. 325
Hood ..... .. .. .. ................. 256
Start ing . . . . . . . . . . . . . . . . . . . . 107, 108
Starting with jumpe r cables ........ . 317
Stopping ........ .. ............... 108
Engine compartment
Safety instr uctions .. ........... .... 256
Work ing the eng ine compartment .. .. 256
Engine coolant system . .. ..... ... .. .. 262
Adding coo lant ..... . .. .. ..... ... .. 264
Checking coolant level .............. 263
Checking the engine coolant level ... .. 263
Malfunction . . . . . . . . . . . . . . . . . . . . . . . 32
Radiator fan ..... .. ............... 265
E ngine coolant temperature
Temperat ure gauge ............ .... . 10
E ngine hood
Closing ... .. .... .. . .. .. ..... ... .. 2 56
How to re lease the hood ..... ... .. .. 256
Engine o il ..... ... .. ............... 258
Adding ... .. .. .. ............... .. 261
Addi tives .... .. ...... ........... .. 261
Chang ing ... .. .... .. ... ..... ... .. 261
Checking the engine oil leve l .. ... .. .. 260
Consumption . ..... . .. .. ..... ... .. 259
Ind ications and conditions requir ing ex-
tra checking . .. .. ............... .. 260
Oil grades . .. .. .. ................. 258
Recommended oil check intervals . .. .. 260
Spec ificat io n and viscosity .......... . 258