2015 AUDI Q7 spare wheel

M N
0 ...J
'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
authorized Audi dealer. Replace a damaged
tire as soon as possible.
- Inspect your tires every 2 ,000 miles (3,000
km) for damage and wear. Damage is not a l­
ways easy to see . Damage can lead to loss of
air and underinflation, which could eventu­
ally cause tire failure. If you be lieve that a
t ire may have been damaged, replace the
t ire as soon as possible .
- These tires may wear more quick ly than oth­
ers .
- Please also remember that, while these tires
deliver respons ive handling, they may ride
less comfortably and make more noise than
other cho ices .
Reduced perform ance in winte r/cold
s eason conditions
All tires are des igned for certai n purposes.
The low aspect ratio, ultra high pe rformance
tires orig inally installed on your veh icle are in­
tended fo r max imum dry and wet road per­
formance and handling . They are not s uitable
for cold, snowy or icy weather conditions. If
you drive under those circumstances, you should equip your vehicle with all-season or
winter tires, which offer better traction under those cond itions . We suggest you use the rec­
ommended snow or all-season tires specified
for your vehicle, or their equ ivalent .
Refer to
c> page 298 for more detailed infor­
mat ion regarding winter t ires.
Tire pressure
monitoring system
(D General notes
Each t ire, includ ing the spare (if provided),
should be checked monthly when cold and in­
flated to the inflation pressure recommended
by the vehicle manufacturer on the vehicle
p lacard or tire inflation pressure label. (If your
ve hicl e has t ires of a different size than the
si ze ind icated on the vehicle p lacard or tire in­
flation pressure label, yo u should determine
the proper tire inflation pressure for those
tires).
Tire s an d wheel s 301
As an added safety featu re, your veh icle has
been equipped with a tire pressure monitoring
system (TPMS) that illum inates a low tire
pressure telltale when one or more of your
tires is significantly under-inflated. According­
ly, when the low tire pressure telltale illumi ­
nates, you should stop and check your tires as
soon as possib le, and inflate them to the
proper pressu re. Driving on a sign ifi cantly un­
der- infla ted ti re causes the tire to overhea t
and can lead to tire fa ilure . Unde r-inflation al­
so reduces fuel efficiency and tire tread life,
and may affect the vehicle's handling and
stopp ing ability.
Please note that the TPMS is not a substitute
for proper tire maintenance, and it is the driv ­
er's responsibility to maintain correct tire
pressure, even if under-inflation has not
reached the level to tr igger illuminat ion of the
TPMS low tire pressure tellta le.
Your vehicle has also been equipped with a
T PMS malfunction ind icator to ind icate when
the system is not operating properly . The
TPMS malfunction indicator is combined with
the low tire pressure telltale . Whe n the sys ­
tem detects a malfunction , the telltale will
flash for approximate ly one m inute and then
rema in continuously illum inated . Thi s se ­
quence will continue upon s ubseque nt vehicle
start-ups as long as the malfunct ion exists.
When the malfunction indicato r is illum inat­
ed, the sys tem may not be ab le to detect or
s ignal low tire pressure as intended. TPMS
malfunctions may occur for a var iety of rea­
sons, including the insta llation of rep lace­
ment or a lternate tires or wheels on the vehi­
cle that prevent the TPMS from functioning
properly. Always check the TPMS malfunction
telltale after rep lacing one or more tires or
whee ls on your vehicle to ensure that the re ­
placeme nt or alternate ti res and wheels allow
the TPMS to cont inue to funct ion p rope rly . •
•

304 What do I do now?
What do I do now?
Jack, tools and
inflatable spare tire
Tools
The tool kit is located in the luggage com­
partment under the cargo floor cover.
Fig . 256 Luggage compartmen t: vehicle too l kit
The onboard tool kit includes:
- Hook for removing wheel covers*
- Plastic hook to remove wheel bolt covers*
- Wheel bolt wrench
- Alignment p in for changing wheels
- Screwdriver with reversible blade
- 10 x 13 open ended wrench
-Towing eye
(D Tips
Some of the onboard items listed above
are provided on certa in models only or are
optional extras .
Jack and folding chocks
The jack and the folding chocks are located in
the luggage compartment under the cargo
floor cover.
Fig. 257 Luggage compartment veh icle jack and fo ld­
ing chocks
-----........ -
Fig. 258 Opening fold ing chocks
Vehicle jack
The jack is located under the tool kit
<=>fig . 257. Before storing the jack, make sure
it is wound back down as far as it will go.
Folding chocks
Two unassembled fo lding chocks are attached
to the foam section at the front with the jack
<=> fig. 257.
Release the two hook-and-loop fasteners, and
remove the two chocks. To use the chocks, you
first have to raise the support plate
<=> fig. 258 (!) and then insert the locking plate
with the two "tabs" into the elongated holes
in the base plate@<=>&. .
A WARNING
-- The chock cannot fulfill its function and
may lose its stability if the "tabs" on the
support plate are not inserted correctly
into the elongated holes in the base

M
"' 0 _,
"". rl I.O
"' rl
"' rl
plate. If this hap pens , the vehicle may
start to m ove whi le a whee l is being
changed.
- Never use the folding chocks if they are
damaged or i f they have not been assem­
bled correct ly.
A WARNING
Improper use of the vehicle jack can cause
ser ious personal injuries.
- Never use the jack supplied with your
Audi on another vehicle, particularly on a heavier one. The jack is only suitable for
use on the vehicle it came w ith .
- Us ing a bumper jack to raise the vehicle
will damage the bumper system. The
jack may slip, causing i njury.
- Never support your vehicle on cinder bloc ks, b ricks or other objects. Th ese
may not be able to support the load and
cou ld cause injury when they fail.
- Never start or run t he engine while the
vehicle is suppor ted by the jack.
- If you must wo rk under the vehicle, al­
ways use safety stand s spe cifically de­
signed for this purpose.
- Always make sure the inflatable spare
tir e a nd even a f lat t ire are se cured in
place and not loose, ot herwise they
cou ld fly forward, causing personal inj ury
to passengers in the veh icle in an acc i­
dent or sudden mane uver.
Removing bass box
Applies to vehicles: with bass box
Before the inflatable spare tire can be taken
out, the bass box must be removed .
Fig . 259 Spare wheel well: Bass box
What do I do now ? 305
Removing bass box
.,. Squee ze the locking tabs ~ fig . 259 (D of
the conne ctor .
.,. Disconnect the connector @and place the
lead to one side.
.,. Turn the large screw counter-clockwise .
.,. Carefully remove the bass box.
Installing bass bo x
.,. Carefully p lace the bass box in the wheel.
The inscription "F RO NT" on the bass box
must face forward .
.,. Reconnect the connector that was removed.
.,. Secure the bass box with the large screw .
Inflatable spare tire
The inflatable spare tire expands to its full di­
ameter when it is inflated.
Fig. 2 60 In flatable spare tir e w ith compressor
Removing inflatable spare tire
.,. Lift up the cargo floo r us ing the handle .
"' Turn the large screw
9 fig . 260 counte r-
clockw ise.
"' Remove the bass box as required
¢ page 305 .
.,. Take out the in flatable spare tire .
.,. Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
partment
9 page 169.
Stowing the inflatable spare t ire
"' Release the ai r by u nscrewing the valve
stem .
.,. Screw the valve stem back in afterwards .
.,. Wait a few hours before p lac ing the wheel in
the spare wheel we ll¢ ,& .
"' Install the bass box as required ¢
page 305 . ..,_

306 What do I do now?
• Secure the wheel with the large screw.
• Fold the cargo floor back down .
After using th e inflat able spare wheel
The inflatable spare t ire can be re-used as
l ong as it is not damaged and is not worn
down to the tread wear ind icators
c::> A .
When you let the air out of the inflatable
spa re tire, it does not assume its folded shape
again for several ho urs. Until then, it cannot
be p laced back in the spare wheel well and
stowed securely.
A WARNING
- Never use the spare tire if it is damaged
or if it is worn down to the tread wear in­
dicators.
- If the inflatable spare tire is more than 6
years old, use it on ly in an emergency
and w ith extreme caut ion and careful
dr iv ing .
- The inflatable spare tire is intended only
for temporary and short-term use .
It
should be replaced as soon as possible
with the no rmal wheel and tire .
- The tire pressure value for the inflatable
spare t ire is located on the driver's side
B-p illar
c::> page 278, fig . 251 .
-Maximum perm iss ible speed is SO mph
(80 km/h).
- Avoid full-throttle acce le rat ion, heavy
braking, and fast corner ing .
- When the air is let out of the inflatable
spare wheel, it does not assume its fold­
ed shape for several hours . Until then, it
cannot be placed back in the spare wheel
we ll and stowed secu rely.
- Never drive with more than one inflata­
ble spare ti re.
- For technical reasons, the use of ti re
chains on the inf latable spare tire is not
permitted.
If i t is necessary to drive w ith
t ir e cha ins, the infla table spare whee l
must be moun ted on the front axle in the
event of a flat in a rear tire . The newly
available front whee l must the n be in­
sta lled in place of the rear wheel with the flat tire
. Insta lling the t ire cha in be­
fore mounting the wheel and tire is rec­
ommended.
- Loose items in the passenger compart­
ment can cause serious personal injury
during hard brak ing or in a n accident.
Never store the inflatable spare tire or
jack and tools in the passenge r compart­
ment.
(D Note
- The inflatable spare tire has been deve l­
oped specifically for t his veh icle mode l.
It must not be exchanged or used for
other vehicle models. Sim ila rly, inflata­
ble t ires from other vehi cle models m ust
no t be used.
- Norma l summer or w inte r ti res m ust not
be ins talled on the infla table t ire rim.
Inflating inflatable spare tire
• Remove the compressor from the luggage
compa rtment
c::> page 305 , fig. 260.
• Unscrew the valve stem from the spare tire.
• Screw the tire f iller hose from the compres­
sor firmly onto the
va lve of the spare tire.
• Insert the plug from the compressor into an
outlet of the ve hicle
c::> page 90 .
• Switch the comp resso r on .
• Let the compressor run unti l the va lue speci­
fied on the ti re p ressu re label is reached
c::> page 278, fig. 251 . Switc h the compres­
sor off after running for 12 m inutes at the
most -danger of overheating!
A WARNING
-The compressor and the tire f iller hose can
become extremely hot while t hey are run­
n ing -danger of burns!
([) Note
Switch the compressor off after ru nning
for 12 min utes at the most -danger of
overheating! Allow the compressor to cool
down for a few m inutes before you use it
again .

M N
0 ..J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel .
.,. After you experience a tire fa ilure, pull the
car well away from moving traffic and try to
reach
level gro und before you stop¢.&_ .
.. All passengers should
leav e the car and
move to a safe location (fo r instan ce, be hind
the guardra il)¢ .&_.
.,. Engage the
parkin g brake to prevent your
vehicle from ro lling unintentionally¢ .&_.
.. Move
selecto r le ver to p osition P ¢ .&_ .
1> Ifyou are towing a trai ler: unhitch the trail­
er from your veh icle.
.,. Block the diagonally opposite wheel with
the folding chocks or other objects.
.. Take the
jack and the inflatab le spare tire
out of the luggage compartment
¢page 304.
& WARNING
You or your passengers cou ld be injured
while changing a whee l if yo u do not fol­
low these safety precautions:
- If you have a flat t ire, move a safe dis ­
tance off the road . Turn off the eng ine,
t ur n the emergency flashers o n and use
other warning devices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To he lp prevent the veh icle from mov ing
sudden ly and possibly slipping off the
jack, always fully set the parking b rake
and block the whee l diagonally opposite
the wheel being cha nged with the fo ld­
ing chocks or othe r objects. When one
front whee l is lifted off the g ro und, plac­
ing the A utomat ic Transm iss ion in P
(Park) wi ll
not prevent the vehicle from
moving .
-
What do I do now? 307
-Before you change a whee l, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
partment
<=:>page 169 .
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order.
1. Activate the vehicle jack mode (only
vehicles with Adaptive Air S uspension)
¢ page 161 .
2. Remove the decorati ve wheel co ver* . For
more details see also <=:>
page 308, Deco­
rative wheel covers
or <=:> page 308,
Wheels with wheel bolt caps.
3. Loosen the wh eel bolt s¢ page 308 .
4. Loca te the p roper mounting point for the
jack and align the jack be low that point
¢ page 309.
5. Lift the car with the jack Q page 309 .
6. Remove the wheel with the flat ti re and
then install the
inflatable spare tire
¢ page 310.
7. Tig hte n all wheel bolts lightly.
8.
L owe r the vehicle with the jack .
9. Use the wheel bolt w rench and
firmly
t ighten all wheel bolts¢ page 308.
10. Replace the decora tive whe el co ver* .
11. Deactivate the vehicle jack mode (on ly
vehicles with Adaptive Air S uspension)
¢ page 161 .
A WARNING
Always read and follow all WARNINGS and
informat ion<=:>
& in Raising the vehicle on
page 310
and <=:> page 311.
•
•

310 What do I do now?
& WARNING
-You or your passengers could be injured
while changing a wheel if you do not
follow these safety precautions:
- Position the jack only at the designated
lifting points and align the jack. Other­
wise, the jack could slip and cause an injury if it does not have sufficient hold
on the vehicle.
- A soft or unstable surface under the
jack may cause the vehicle to slip off the jack. Always provide a firm base for
the jack on the ground . If necessary,
use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
just as necessary and then continue to
raise the jack.
(D Note
Do not lift the vehicle by the sill. Position
the jack only at the designated lifting
points on the sill. Otherwise , your vehicle
will be damaged.
Taking the wheel off /installing the
inflatable spare tire
Follow these instructions step-by-step for
changing the wheel
Fig. 266 Changing a wheel: alignment pin inside the
top hole
After you have loosened all wheel bolts and raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.,. Remove the topmost wheel bolt completely
and set it aside on a
clean surface.
.,. Screw the threaded end of the
alignment
pin
from the tool kit hand-tight into the
empty bolt hole
¢ fig . 266.
.,. Then remove the other wheel bolts as de­
scribed above.
.,._Takeoff the wheel leaving the alignment pin
in the bolt hole ¢(D.
Putting on the inflatable spare tire
.,. Inflate the inflatable spare tire ¢ page 306
and push the wheel over the alignment pin.
"Screw in and tighten all wheel bolts
slightly.
.,. Remove the alignment pin and insert and
tighten the remaining wheel bolt slightly
like the rest .
.,. Turn the jack handle counter-clockwise to
lower the vehicle until the jack is fully re­
leased .
" Use the wheel bolt wrench to tighten all
wheel bolts firmly ¢
page 308 . Tighten
them
crosswise, from one bolt to the (ap­
proximately) opposite one, to keep the
wheel centered.

M N
0 ...J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
(D Note
When removing or installing the wheel,
the rim could hit the bra ke rotor and dam­
age the rotor . Wor k carefully and have a
second person help you.
- W hen mounting tires with
unidirectional
tread design
ma ke s ure the tread pat­
tern is pointed the r ight way
<=> page 311.
-The wheel bolts should be clea n and easy
to tu rn. Check for d irt and corrosio n on
t h e mat ing su rfaces of both the whee l
and the hub. Remove a ll dirt from these
su rfaces before remo untin g t he wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tr ead pattern point ed in
the right dire ction.
Using a spare tire with a tread pattern
intended for use in a specific direction
W hen using a spa re tire w ith a t read patte rn
in te nded fo r use in a specific direction, p lease
n ot e t he followi ng:
- The direction of rotation is marked by an ar­
row on the side of the tire.
- If the spare tire has to be installed in the in­
correct di rection, use the spa re tire only
tem porarily si nce th e tir e will not be able to
a ch ieve i ts op timum pe rfo rm ance chara cter­
is tics with reg ard to aq uaplani ng, noise and
wea r.
- W e recommend that you p ay pa rticular at­
tent io n t o this fact du ring wet weathe r and
t h at you adjus t your spee d to matc h roa d
con dit ions.
- Re place the fla t tire w ith a new one and
have it installed on your vehicle as soon as
poss ible to restore the hand ling advantages
of a unid irect iona l tire.
What do I do now?
Notes on wheel changing
P lease read t he i nfo rmat ion c:> page 291, New
t ires and replacing tires and wheels
if y ou a r e
go ing to use a sp are tire w hich is different
from the ti res on yo ur vehicle.
After yo u cha nge a tire:
- Check the tire pressure on the spare imme­
diately after installation .
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as
possible by your authorized Audi dealer or
a qualified workshop.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 120 ft lb (160 Nm) .
- If you notice that the wheel bolts are cor­
roded and difficult to turn while changing
a tire, they should be replaced before you
check the tightening torque.
- Repla ce the flat tire with a new one and
have it installed on your vehicle as s oon as
possible. Remount the wheel cover.
Until then, drive with extra care and at re­
duced speeds .
&_ WARNING
-
- If yo u are goi ng to e quip yo u r ve hicl e
wit h tires o r rims whi ch di ffer from those
which were fac to ry installed, t hen be
sure to rea d the information
c:> page 2 91,
New tires and replacing tires and
wheels.
- Always make s ure the damaged wheel o r
even a flat tire and the jack and t ool kit
are prope rly secured in the luggage com ­
pa rtme nt and are not loose in the pas ­
senge r compartment .
- In an accident or sudden maneuver they
could fly forwa rd, inj uri ng a nyo ne in the
veh icle.
- Always sto re damaged wheel , jack a nd
too ls sec urely in the luggage compa rt­
men t. Othe rwise, in a n accide nt o r sud­
de n m aneuver they could fly forwa rd,
c a u sing i nju ry to passenger s in th e ve hi­
cle.
311
•
•