2015 AUDI Q5 warning

Emergency situation s
When jump starting or charging the battery,
never connect the negative ground cable to
the battery negative post because the bat­
tery manager system must be able to detect
the battery's state of charge. Always con­ nect the negative ground cable to the nega ­
tive ground post of the battery manager
control un it.
Use of jumper cables
Make sure to connect the jumper cable clamps in
exactly the order described below!
Fig. 227 Engine co mpar tment : Connectors for ju mp er ca ­
bl es and charger
Fig. 228 Jum p starting wi th the battery of anot her ve hicl e:
@ booste r batte ry ,@ discharged vehicle battery
The procedure described be low for connecting
jumper cables is intended to provide a jump start for your vehicle.
Hybrid drive*: read the important information
concerning a dead high voltage battery under
c;,page 105.
Vehicle with discharged battery:
• Turn off lights and accessories, move lever of
automatic transmission to N (Neutral) or P
(Park) and set parking brake.
272
Connect POSITIVE(+) to POSITIVE (+) (red)
• Remove the cover (!) by pressing on the arrow
¢fig. 227.
• Open the cover @on the positive terminal.
1. Connect one end of the red positive cable on
the
jump start bolt c::> fig. 228 @ (Bolts un­
der cover = "positive") of the vehicle to be
started @.
2 . Connect the other end to the positive termi-
nal @ of the booster battery @.
Connect NEGATIVE (-) to NEGATIVE (-)
(black)
3 . Connect one end of the black negative cable
to the negative terminal @ of the booster
battery @.
4. Connect the other end of the black negative
cable to the
jump start bolt © (Bolts with
hex head= "negative") of the vehicle to be
started @.
Starting the engine
• Start the engine of the vehicle with the booster
battery @. Run the eng ine at a moderate
speed.
• Start engine with discharged vehicle battery @
in the usual manner.
• lfthe engine fails to start: do not keep the
starter cranking for longer than 10 seconds.
Wait for about 30 seconds and then try again.
• With engine running, remove jumper cables
from both vehicles in the exact
reverse order .
• Close the cover @on the positive terminal and
re-install the cover@¢
fig. 22 7.
The battery is vented to the outside to prevent
gases from entering the vehicle interior . Make
sure that the jumper clamps are well connected
with their
metal parts in full contact with the
batte ry terminals.
& WARNING
To avoid serious personal injury and damage
to the veh icle, heed all warnings and instruc­
tions of the jumper cable manufacturer. If in
doubt, call for road service.
- Jumper cables must be long enough so that
the vehicles do not touch. ..,.

M N
co ~ co
rl I.O
"' N
"' rl
-When conne cting jump er cabl es, make sur e
that they cannot get caught in any moving
parts in the engine compartment.
- Do not bend over the batteries -danger of
chemical burns!
- The battery cell locking screws must be
tightened securely .
- Before you check anything in the engine
compa rtment, always read and heed all
WARNINGS
¢ page 221.
(D Note
Improper hook-up of jumper cables can ruin
the generator.
- Always connect POSITIVE(+) to POSITIVE
(+), and NEGATIVE(-) to NEGATIVE(-)
ground post of the battery manager control
unit.
- Check that all screw plugs on the battery
cells are screwed in firmly . If not, tighten
plugs prior to connecting clamp on negative
battery terminal.
- Please note that the procedure for connect­
ing a jumper cable as described above ap­
plies specifically to the case of your vehicle
being jump started . When you are giving a
jump start to another vehicle, do
not con­
nect the negative(-) cable to the negative
(-) terminal on the discharged battery@
¢
fig. 228. Instead, securely connect the
negative (-) cable to either a solid metal
component that is firmly bolted to the en­
gine block or to the engine block itself. If
the battery that is being charged does not
vent to the outside, escaping battery gas
could ignite and explode !
Towing with a tow truck
General hints
Your Audi requires special handling for towing .
The following information is to be used by com ­
mercial tow truck operators who know how to op­
e rate their equipment safely .
-Never tow your Audi, towing will cause dam­
age to the engine and transmission.
Emergency situations
- Never wrap the safety chains or winch cables
around the brake lines.
- To prevent unnecessary damage, your Audi
must be transported with a flat bed truck.
- To load the vehicle on to the flat bed, use the
towing loop found in the vehicle tools and at­
tach to the front or rear anchorage
¢ pag e 273 and ¢ pag e 274.
A WARNING
--
A vehicle being towed is not safe for passen­
gers. Never allow anyone to ride in a vehicle
being towed, for any reason .
Front towing loop
Do not install the front towing loop unt il it is
needed.

Fig. 229 Fro nt bump er: r em oving th e cover ca p

.·~G
' -
Fig. 230 Fro nt bumper: s crewing in th e tow in g l oo p
The towing loop fits into the threaded hole locat­
ed on the right side of the front bumper and
cov­
ered by a cover when not in use.
.,. Remove the towing loop from the vehicle tool­
kit ¢
page 255.
"' Carefully remove the cover ¢ fig. 229 .
.,. Screw the towing loop tightly into the threaded
hole as far as it will go¢
fig. 230. IJi,,
273

Emergency situation s
When it is no longer needed, unscrew the towing
loop and put it back into the vehicle toolkit . Be
sure to have the tow ing loop stored in the vehicle
at all times .
When re -insta lling the cover be su re to first in­
sert the tabs on the cover into the retainers near
the radiator grille . T hen install the other side of
the cover and push it into the retainers
¢f ig. 229 .
The appearance of the cover var ies from the illus­
tration for some model versions .
A WARNING
If the towing loop is not screwed in as far as it
w ill go, the thread can pu ll out when the veh i­
cle is towed -potential risk of an accident .
(D Note
The cover is attached to the bumper with sev­
eral hooks . Do not use excessive force when
remov ing the cover to avoid damaging it.
Rear towing loop
On vehicles without a factory-installed trailer
hitch*, the threaded hole for the towing loop is
on the right side of the rear bumper .
Fig. 2 31 Rear b umper: Cove r
274
N
N
---- ~ a, al
F ig . 232 Rea r bumpe r: S crew ing in t owing loop
Vehicles with a towing loop
~ Remove the tow ing loop from the vehicle tool ­
ki t
¢ page 255.
~ Press t he cover i n by app lyi ng short strong
pressu re to the bottom pa rt to release it from
t he bumper
¢fig . 231.
~ Sc rew the towing loop t ightly into t he threaded
hole as far as it will go¢
fig. 232.
Vehicles with a trailer hitch*
~ In sta ll the tra ile r hitch.
~ Attach the tow ing bar or the tow ing ca ble to
the t ra iler hi tch .
Unscrew the towi ng loop again afte r use and i n­
st all the cover in the b um pe r. Retur n the towing
l oop to the vehicle tool kit . B e sure to have the
tow ing loop stored in the vehicle at all times .
~ WARNING
-If the towin g loop is not screwed in as fa r as
it will go, the thread can pull out when the
veh icle is towed - potent ial risk of an acci­
de nt.
- If your vehicle has a
tra iler hitch* only use a
specia l towing bar to p revent damag ing t he
ball hitch. These towing bars have been spe­
cially designed for trailer towing h itches .
- If your vehicle has a
tra iler hitch* use on ly
special towing cables .

M N
co ~ co
rl I.O
"' N
"' rl
Loading the vehicle onto a flat bed truck
Fig. 233 Veh icle on flat bed truck
Front hook up
• Align the vehicle with the centerline of the car
carrier ramp.
• Attach the winch hook to the front towline eye
previously installed .
Rear hook up
• Align the vehicle with the centerline of the car
carrier ramp.
• Attach the winch hook to the rear towline eye
previously installed.
@ Tips
Check carefully to make sure the hook-up is
secure before moving the car up the flatbed
truck ramp .
Raising the vehicle
Lifting with workshop hoist and with floor
jack
The vehicle may only be lifted at the lifting
points illustrated .
Fig. 234 Front lift ing point
Emergency situations
Fig. 23S Rear lifting point
• Read and heed WARNING ~ .&, .
• Locate lifting points ¢ fig. 234 and ~ fig. 235 .
• Adjust l ifting arms of wo rkshop hoist or floor
jack to match vehicle lifting points.
• Insert a rubber pad between the floor jack/
workshop hoist and the lifting points.
If you must lift your vehicle with a floor jack to
work underneath, be sure the vehicle is safely
supported on stands intended for this purpose.
Front lifting point
The lifting point is located on the floo r pan rein­
forcement about at the same level as the jack
mounting point¢
fig. 234. Do not lift the vehi·
cleat the vertical sill reinforcement.
Rear lifting point
The lifting point is located on the vert ica l rein­
forcement of the lower sill for the on board jack*
¢fig. 235.
Lifting with vehicle jack*
Refer to ¢ page 262 .
A WARNING
-To reduce the risk of ser ious injury and vehi­
cle damage.
- Always lift the vehicle only at the special
workshop hoist and floor jack lift points il­
lustrated
q fig. 234 and ¢ fig. 235.
-Failure to lift the vehicle at these points
could cause the vehicle to tilt or fall from
a lift if there is a change in vehicle weight
distribution and balance . This might hap-
pen, for example, when heavy components
Ill>
275

M N
co ~ co
rl I.O
"' N
"' rl
Technical data
Vehicle identification
F ig. 236 Veh icle Identificat ion Number (VlN) plate: loca·
t ion on driver 's side dash pane l
XXXXX XX -X -XXXX XXX XX
CD+ ~t :1:: xxxxxxxx xx x xxxxxxxx
T VP /fffl XXX XXX
XX XXXXXXX XX X X XX
XXX
KW XXX
®i ~:J ·f lfils~~ XXXX XXX XXX
®-+ ~ N:a=i~l xxxx ; xxxx xxx ; xx
11. • AUSS, I OPTIONS
E0A 7D5 4UB 6XM 5SG 5R W
2EH J0Z lLB l
A S lBA
3FC SMU 7Xl
FOA
9G3 0G7 0YH OJF
TL 6 3 KA
8EH UlA X98 QZ 7
lXW 803 908 824 020
7T6 CV7 7K0 4X3 2K2
3L4 4KC 3Y0 413 502
lS A
7GB 01A 4G0
XX. X XX X XX X xxxx
Fig. 237 Veh icle identificat ion label: inside the luggage
compartment
Vehicle Identification Number (VLN )
The Veh icle Iden tific ation Number is located in
d iffe rent p laces:
- under the w indshield on the dr iver's side
c::> fig . 236.
-in the radio or in the MM I*: Select: I CAR I func­
t ion but ton
> Vehicle ID numb er (VIN ) or se·
Le et
I CAR I funct ion button > Car sy s tem s* con·
tro l bu tton
> Servicing & checks > VIN num­
ber .
-on the vehicle identific ation label.
Technical d ata
Vehicle id entification label
T he vehicle identification label is lo cate d in the
lu ggage compartment above the compartment
for the vehicle too ls.
T he label
c::> fig . 23 7 shows the fo llow ing vehicle
da ta:
(D Vehicl e Ident ificat ion Number (VIN)
@ Vehicle type, engine o utp ut, transmission
@ Engine and transm ission code
@ Pain t number and inte rior
® Optional equipment numbers
T he information of the vehicle identification label
can a lso be found in your W arranty
& Ma inte­
nance booklet.
Safety compliance sticker
T he safety complianc e sticker is your assurance
that your new vehi cle complies w ith all appli cable
F ede ra l Mo to r Vehi cle Safety Sta ndards which
were in effec t at the time the vehicle was ma nu­
fact ured. Yo u can find this sticker on the door
jamb on the driver's side. It shows the month and year of product ion and the vehicle identification
number of your vehicle (perforation) as well as
t h e Gross Veh icle Weight Rating (GVWR) and the
G ross Ax le Weight Rating (GAWR).
H igh vo lt a ge warn ing lab el
The high voltage warning label is located in the
engi ne compartment next to the engine hood re·
lease. The spark ignit ion system complies with
the Canadian standard ICES-002 .
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rating (GVWR), and
the Gross Axle Weight Rat ing (GAWR) for front
and rear are listed o n a sticker on the door jamb
on the dr iver's side.
The Gross Vehicle Weight Rating includes the
weight of the bas ic vehicle plus full fuel tank, oil
and coolant, plus maximum load, which includes
passenger weight (150 lbs/68 kg per designated
seat ing pos ition) and luggage we ight
c::> .&, . ..,_
277

Technical data
Gross Axle Weight Rating
The Gross Axle Weight Rating is the maximum
load that can be applied at each axle of the vehi ­
cle ¢& .
Vehicle capacity weight
The vehicle capacity we ight (max. load) is listed
on the driver's side 8 -p ill ar.
_& WARNING
- T he actual Gross Axle Weight Rating at the
front and rear axles should not exceed the
permissible weights, and their combination
must not exceed the Gross Vehicle Weight
Rating.
Dimensions
Length in (mm)
Width in (mm)
Width (across mirrors) in (mm)
Height (unloaded)al in (mm) -
Exceeding permissible weight ratings can
result in veh icle damage, acc idents and per­
sonal injury.
(D Note
- The vehicle capacity weight figures apply
when the load is distributed evenly in the
vehicle (passengers and luggage). When
transporting a heavy load in the luggage
compartment, carry the load as near to the
rear axle as possible so that the vehicle's
hand ling is not impaired.
- Do not exceed the maximum permissible
axle loads or the maximum gross veh icle
we ight. Always remember that the vehicle's
hand ling will be affected by the extra load.
T herefore, adjust your speed accordingly.
- Always observe local regulations .
QS/QS hybrid SQS
182.6 (4639) 183 .0 (4647)
74.7 (1898) 75 .2 (1911)
82.2 (2089) 82 .2 (2089)
65 .2 (1655) 65.3 (1658)
al T h e he ight of t he ve hicl e depends on the tires and the su spens ion.
When driving up steep ramps, on rough roads,
over curbs, etc. it is important to remember that
some parts of your vehicle, such as spo ilers or ex- haust system components, may be close
to the
ground . Be careful not to damage them.
Capacities
QS/SQS QS hybrid
Fuel tank: total capacity gal (liters) approx. 19.8 (75) approx. 19.0 (72)
Windshield and headlight* quarts (liters) approx.
4.9 (4.6) approx. 4.9 (4.6)
washer fluid container
278

Consumer information
today's automobiles, have steadily reduced the
scope of maintenance and repairs which can be
carried out by vehicle owners.
Also, safety and
environmental
concerns place very strict limits
on the nature of repairs and adjustments to en­
gine and transmission parts which an owner can perform .
Maintenance, adjustments and repairs usually re­
quire special tools , testing devices and other
equipment available to specially trained work ­
shop personnel in order to assure proper per­
formance, reliability and safety of the vehicle and its many systems.
Improper maintenance, adjustments and repairs
can impair the operation and reliability of your
vehicle and even
void your vehicle warranty .
Therefore, proof of servicing in accordance with
the maintenance schedule may be a condition for
upholding a possible warranty claim made within
the warranty period .
Above all, operational safety can be adversely af­
fected, creating unnecessary risks for you and
your passengers.
If in doubt about any servicing, have it done by
your authorized Audi dealer or any other properly equipped and qualified workshop. We strongly
urge you to give your authorized Audi dealer the
opportunity to perform all scheduled mainte­ nance and necessary repairs. Your dealer has the
facilities, original parts and trained specialists to keep your vehicle running properly.
Performing limited maintenance yourself
The following pages describe a limited number of
procedures which can be performed on your vehi­
cle with ordinary tools, should the need arise and
trained personnel be unavailable. Before per­
forming any of these procedures, always thor­
oughly read all of the applicable text and careful­ly follow the instructions given . Always rigorously
observe the
WARNINGS provided.
Before you check anything in the engine com­
partment, always read and heed all WARNINGS
c::> & and c::> & in Working in the engine compart­
ment on page 221 .
282
A WARNING
-
-Serious personal injury may occur as a result
of improperly performed maintenance, ad ­
justments or repairs.
- Always be extremely careful when working
on the vehicle . Always follow commonly ac­
cepted safety pract ices and general com­
mon sense. Never risk personal injury.
- Do not attempt any of the maintenance,
checks or repairs described on the following
pages if you are not fully familiar with these
or other procedures with respect to the vehi­
cle, or are uncertain how to proceed.
- Do not do any work without the proper tools
and equipment. Have the necessary work
done by your authorized Audi dealer or an­
other properly equipped and qualified work­
shop.
- The engine compartment of any motor vehi­ cle is a potentially hazardous area. Never
reach into the area around or touch the radi­
ator fan. It is temperature controlled and
can switch on suddenly - even when the en­
gine is off and the ignition key has been re ­
moved. The radiator fan switches on auto­
mat ically when the coolant reaches a certain
temperature and will continue to run until
the coolant temperature drops.
- Always remove the ignition key before any­
one gets under the vehicle.
-Always support your vehicle with safety
stands if it is necessary to work underneath
the vehicle. The jack* supplied with the vehi­
cle is not adequate for this purpose and
could collapse causing serious personal in­
jury.
- If you must work underneath the vehicle
with the wheels on the ground, always make
sure the vehicle is on level ground, that the
wheels are always securely blocked and that
the engine cannot be started.
- Always make sure the transmission selector
lever (automatic transmission) is in P (Park
position) and the park brake is applied.

M N
co
a:
co
,...., \!) 1.1'1
N 1.1'1 ,....,
@ For the sake of the environment
-Changing the engine settings wi ll adversely
affect emission levels. This is detrimenta l to
the environment and increases fuel con­
sumption.
-Always observe environmental regulations when disposing of old engine o il, used brake
flu id, dirty engine coolant, spent batteries
or worn out tires .
- Undeployed airbag modules and pretension­
ers might be classified as Perchlorate Mate­
rial -spec ial handling may apply, see
www .dtsc.ca .gov/hazardouswaste/perchlo­
r ate. When the vehicle or pa rts of the re­
stra int system incl uding airbag modules
safety be lts with pre tensioners are scrap­
ped, all applicab le laws and regulations
must be observed . Your authorized Audi
dealer is familiar with these requirements
and we recommend that you have your deal­
er perform this service for you.
Accessories and
technical changes
Additional accessories and parts
replacement
Always consult an authorized Audi dealer before
purchasing accessories.
Your vehicle incorporates the latest safety design
features ensuring a high standard of act ive and
passive safety.
This safety could be compromised by non -ap­
proved changes to the ve hicle . For this reason, if
parts have to be replaced, please observe the fol­
lowing po ints when insta lling addit ional accesso­
ries:
Approved Audi accessories and genuine Audi parts are avai lable from authorized Aud i dea lers.
These dealers also have the necessary faci lities,
too ls and trained specialists to insta ll the parts
and accessories properly.
C o nsum er information
A WARNING
Using the wrong spare parts or using non-ap­
proved accessories can cause damage to the
vehicle and serious personal injury .
- Use on ly accessories express ly approved by
Aud i and genuine Audi spare parts
- These parts and accessories have been spe­
cially designed to be used on your vehicle .
- Never install accessor ies such as telephone
crad les or beverage ho lders on airbag covers
or w ith in the airbag deployment zones . Do ­
ing so will inc rease the r isk of injury if a ir­
bags are triggered in an acc ident!
- Before you check anything in the engine
compa rtment, always read and heed a ll
WARNINGS
9 page 221.
(D Note
- If items other than genu ine Audi spare
parts, add-on equipment and accessory
items are used o r if repair work is not pe r­
formed a ccording to specified methods, this
can result in severe d amage to yo ur vehicle's
eng ine and body (su ch as corrosion) and ad­
verse ly affect your vehicle's warranty.
- If emergency repairs must be performed
elsewhere, have the veh icle examined by an
authorized A udi dealer as soon as possib le .
- T he manufac turer can not be held liable for
damage wh ich occu rs d ue to failure to com ­
ply with t hese stipulations .
Technical Modifications
Our guidelines must be complied with when tech­
nical modifications are made .
Always consult an authorized Audi dealer before
sta rting wor k on any modifications.
This wi ll help ensur e that veh icle function , per­
formance and safety are not impa ired
9 &. .
Attempt ing to work on e lectronic components
and the software used with them can cause mal­
funct ions . Because of the way electronic compo­
nents a re inte rconnected with each other, such
malfu nctions can a lso have an adverse affect on
othe r systems that are not direc tly invo lved. This ..,_
283