2015 AUDI A5 battery

Checking and Filling
-If you get battery acid in your eyes or on
your skin, immediately rinse with cold wa­
ter for several minutes and get medical at­
tention .
- If you should ingest any battery acid, seek
medical attention immediately .
- Do not expose the battery to an open flame, electric sparks or an open light .
- Do not smoke .
- Do not interchange the positive and nega-
tive cables.
- When working on the battery , be sure not to
short-circuit the terminals with tools or oth­
er metal objects . This would cause the bat­
tery to heat up very quickly, which could lead to damage or explosion and personal
injury .
- When a battery is charged, it produces hy­
drogen gas which is explosive and could
cause personal injury.
- Always keep the battery well out of the
reach of children .
- Before work is done on the electrical sys­
tem, disconnect the negative ground cable .
- Before performing any work on the electri­ cal system, switch off the engine and igni­
tion as well as any electrical equipment. The negative cable on the battery must be dis­
connected. If you are just going to replace a
light bulb, then it is enough to switch off
the lights.
- Before disconnecting the battery, switch off
the anti-theft alarm system! Otherwise you
will set off the alarm.
- When disconnecting the battery, first dis­
connect the negative cable and then the
positive cable.
- Before reconnecting the battery, make sure
all electrical consumers are switched off. Re­
connect the positive cable first and then the
negative cable. Never interchange the ca­
bles -this could start a fire!
- Never charge a frozen or a thawed-out bat­
tery. It could explode! If a battery has fro ·
zen, then it must be replaced. A discharged
battery can freeze over at 32°F (0°C).
- Make sure the vent hose is always attached
to the opening on the side of the battery .
202
-Never use batteries which are damaged.
There is the danger of an explosion! Always
replace a damaged battery.
A WARNING
California Proposition 65 Warning:
- Battery posts, terminals and related acces­
sories contain lead and lead compounds,
chemicals known to the State of California
to cause cancer and reproductive problems .
Wash hands after handling .
(D Note
- Do not disconnect the vehicle battery when
the ignition is switched on or when the en­
gine is running, otherwise, you will damage
electronic components in the electrical sys­
tem .
-If your vehicle is going to stand for a long
period of time without being driven, protect
the battery from "freezing", otherwise it
will be damaged and will then have to be re­
placed .
Battery charging
Starting the engine requires a well charged bat­
tery.
Fig. 166 E n g in e compar tmen t: C on nectors fo r charger and
jump er cables
Always read and heed all WARNINGS below
9 A and ¢ A in Working on the battery on
page 201.
.,. Turn off the ignition and all electrical consum­
ers.
.,. Make sure the area is well ventilated when you
charge the battery.
Iii>-

M N
i? co ,...., \!) 1.1'1
N 1.1'1 ,....,
~ Open the engine hood¢ page 191 .
~ Open the cover on the positive pole ~ fig. 166.
~ Connect the charger connectors accord ing to
the instructions to the
jump sta rt bolts . (Bolts
under the cover= "posit ive", Bo lt s with hex
head = "negat ive") .
~ Only now plug the ma ins lead for the charg ing
equipment into the wall outlet and turn it o n
~& -
~ Mak e sure the charging rate i s not o ver
30 amp s/14 .8 Volt .
~ When the battery is fully charged: Turn the
charging equipment
off and remov e the mains
l ead from the wall outlet.
~ Now remove the clamps for the charging equip-
ment.
~ Close the cover on the posit ive pole .
~ Close the hood 9 page 191.
A discharged battery can freeze at temperatures
of only 32 °F (0 °C). Allow a frozen battery to
thaw comp letely before attempting to charge it
9 & . However, we recommend not using a
thawed batte ry agai n because the batte ry casing
can be cracked due to ice forma tion a nd ca n leak
battery a cid.
Battery charging (Maximum charging rate of
30 amps /14.8 Volt )
When charging at low voltages (e.g. w ith a trickle
c harger ),
the battery cab les do not have to be
d isconnected first. The batte ry caps sho uld
not
be opened when charging a battery.
It is not necess ary to remove the ba tte ry from
t he luggage compa rtment.
Fast charging the battery (charging rate
above 14.8 Volts)
F or technica l reasons do no t use a ba ttery charg­
e r that uses voltage grea ter than 14.8 Vol ts to
charge your vehicle's battery .
A WARNING
Charging a battery can be dangerous.
- Always fo llow the operating instructions
provide d by the batte ry charge r manufactur ­
er when c harging your battery.
Checking and Fillin g
-Never charge a frozen battery. It may ex­
plode because of gas trapped in the ice . Al­
low a frozen battery to thaw out first.
- Do not reuse batteries wh ich were frozen.
The battery housing may have cracked and
weakened whe n the battery froze.
- Charge the battery in a well ventilated area.
K eep away from open flame or electrical
spark. Do not smoke. Hydrogen gas gene rat­
ed by the ba tte ry is explosiv e.
- To reduce the danger of explosion, never
connect or d iscon nect charger cab les wh ile
the charge r is operating.
- Fast cha rging a batte ry is dange rous and
should only be at tempted by a compe tent
technicia n w it h the proper eq uipment.
- Battery acid that may sp ill dur ing cha rging
should be washed
off with a solut io n of
warm water and baking soda to neutralize the a cid .
@ Note
Neve r use a fast charger as a booster to start
the e ng ine . T his w ill ser iously damage sensi­
tive elec tronic components, s uch as co ntrol
units , relays, radio, etc. , as we ll as the battery
cha rger.
Battery replacement
The new battery must have the same specifica­
tions and dimensions as the original equipmen t
battery.
Intelligent energy management in your vehicle is
r esponsible for distributi ng the elect rical energy
t hr ough out your veh icle
9 page 175. T he intelli ­
gen t energy management sys tem w ill keep the
engi ne battery cha rged better then vehicles with ­
out this system . To make s ure t he addit iona l elec­
trical energy is avai lab le once again after yo u
have changed the battery, we recommend that
you install bat teries of the same type and manu­
facture on ly (the same as those installed at the
t ime you r vehicle was del ivered) . Specificat ions
are listed on the battery hous ing . You r autho r­
i z ed Audi dea ler m ust code t he battery in the en-
ergy ma nagement system to en able you to use .,,.
203

Checking and Fill in g
th e e nergy management functions correctly after
replacing the battery.
If i t is not poss ible to use a battery of this type,
the new battery must have the same capacity,
voltage (12-vo lts), amperage, construct ion and
p lug sealing.
When insta lling the battery, make sure the igni­
tion and all elec trical consumers are t urned off.
CD Note
Make sure the ventilation hose on the s ide of
t he batte ry is connected, otherwise fumes or
bat tery ac id can leak out.
@ For the sake of the environment
Because of the problem of proper d isposa l of
a battery, we recommend your author ized
Audi dea le r change the battery for yo u. Ba t­
teries contain su lfuric acid and lead and must
always be disposed of properly in compliance
w ith all environmenta l reg ulations. D isposing
of vehicle batteries improperly is very danger­
ous to the environment.
Windshield/headlight* washer container
Fig. 167 Engine co mpa rtment : Cove r on th e w in d shiel d
an d h ead ligh t• was her fl uid container
The washer fluid containe r is marked with the
symbol
O on its cap ¢ fig . 167 , ¢page 193 ,
fig . 161 .
.,. Before you check anyth ing in the eng ine com­
partment , alw ays re ad and he ed all WARN·
I NGS
¢ ,& in Working in the engine comport­
ment on page 191 .
204
.,. Lift the filler cap tongue to add washer fluid.
Yo u can fill the container to the top.
.,. Press the cap back onto the filler neck after fill-
ing the container .
You can find the reservoir ca p acit y in the table in
~ page 242.
Clean water should be used when filling up. If
possible, use soft water to prevent scaling on the
washer jets . Always add a g lass cleaner solution
(with frost protection in the winter) .
CD Note
Do not mix engine coolant antifreeze or any
other additives to fill up the windsh ield wash­
er reservoir.

Emerg enc y s it uat ion s
Emergency situations
General
T his c hapt er is inte nded fo r tra ined e merg ency
c rews a nd worki ng p ers onn el w ho h ave the nec­
e ssa ry tool s and equipm ent t o perf orm the se
op era tion s.
Starting by pushing or
towing
CD Note
Vehicl es with an automa tic tra nsmission
c annot be st arted by pushing or towing .
Starting with jumper
cables
If necessary, the engine con be started by con­
necting it to the battery of another vehicle .
If the engine should fail to start because of a d is­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, us ing a
p air of j umpe r cables to start the engine.
Jump er c abl es
Use only jumper cab les of sufficiently largec ross
sec tion
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use on ly jumper cables with
insulated term inal
clamps which are d istinctly mar ked:
plus (+ ) cabl e in most cases co lored re d
minu s(-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, ac id, and gas.
Any of these can cause very ser ious or fatal in­
jury . Fo llow the inst ruct ions be low for safe
hand Ling of your veh icle's battery.
- Always shield your eyes and avoid leaning
over the battery whenever possible.
- A discharged battery can freeze at tempera­
tures just below 32 °F (0 °C). Before con­
nect ing a jumper cab le, you must thaw the
236
frozen battery completely, otherwise it
could explode.
- Do not allow battery acid to contact eyes or
skin. Flush any contacted area with water immed iately.
- Improper use of a booster battery to start a
veh icle may cause an explosion.
- Vehicle batteries generate explosive gases .
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery.
- The voltage of the booster battery must al­
so have a 12-Volt rat ing . The capacity (Ah)
of the booster battery should not be lower
than that of the discharged battery. Use of batter ies of different voltage or substantial­
ly different "Ah" rating may cause an explo­
sion and personal injury .
- Never charge a frozen battery . Gas trapped
in the ice may cause an explosion .
- Never charge or use a battery that has been
frozen . The battery case may have be weak­
ened .
- Use of batter ies of different voltage or sub­
stantially d ifferent capacity (Ah) rating may
cause an explosion and injury. The capacity
(Ah) of the booster battery sho uld not be
lowe r than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed a ll
WARNINGS
qpoge 191.
CD Note
-App lying a higher voltage booster battery
wi ll cause expensive damage to sensitive
elec tronic components, such as control
units, re lays, radio, etc.
- T here must be no electrical contact between
the vehicles as otherwise cu rrent cou ld al­
ready start to flow as soon as the positive
(+) termina ls are connected.
@ Tips
The discharged battery must be properly con-
nected to the vehicle's electrical system. .,.

M N
0 l­oo
rl I.O
"' N
"' rl
When jump starting or charging the battery,
never connect the negative ground cable to
the battery negat ive post because the battery
manager system must be able to detect the
battery's state of charge. Always connect the
negative g round cab le to the negative ground
post of the battery manager control unit.
Use of jumper cables
Make sure to connect the jumper cable clamps in
exactly the order described below!
Fig. 186 Engine compa rtment: Connectors for jumper ca­
b les and c harger
Fig. 187 Jum p sta rting with the battery of anot her veh icle :
@ boos te r ba ttery, @ discharged veh icle battery
The procedure described below for connecting
jumper cables is intended to provide a jump start
for your vehicle.
Vehicle with discharged battery :
.. Turn
off lights and accessories, move lever of
automatic transmission to N (Ne utra l) or P
(Park) and set parking brake.
Connect POSITIVE(+) to POSITIVE(+) (red)
.. Remove the cover above the jump start connec­
t ion.
.. Open the cover on the posit ive pole ¢
fig. 186.
Emergency situations
1. Connect one end of the red positive cable on
the jump start bolt~
fig. 187 (D (Bolts un­
der cover= "positive") of the vehicle to be
started @.
2. Connect the other end to the positive termi- nal@of the booster battery @.
Connect NEGATIVE (-) to NEGATIVE(-)
(black)
3. Connect one end of the black negative cable
to the negative terminal ® of the booster
battery @.
4 . Connect the other end to the jump start bolt
@ (Bolts with hex head= "negative") of the
vehicle to be started @.
Starting the engine .. Start the engine of the veh icle with the booster
battery @. Run the eng ine at a moderate
speed .
.. Start engine with discharged vehicle battery @
in the usual manner.
.. If the engine fails to start: do not keep the
starter cranking for longer than 10 seconds.
Wait for about 30 seconds and then try again .
.. With engine running, remove jumper cables
from both vehicles in the exact
reverse order .
.. Close the cover on the positive pole.
The battery is vented to the outside to prevent
gases from entering the vehicle inter ior. Make
sure that the jumper clamps are well connected
with their
metal parts in full contact with the
batte ry terminals.
A WARNING
To avoid serious personal injury and damage
to the vehicle, heed all warnings and instruc­
tions of the jumper cable manufacturer. If in
doubt, call for road service.
- Jumper cables must be long enough so that
the vehicles do not touch .
- When connecting jumper cables, make sure
that they cannot get caug ht in any moving
parts in the eng ine compartment.
- Do not bend over the batteries -danger of
chemi cal burns!
237

Emergency situation s
-The ba ttery ce ll lockin g screws must be
t ightened securely .
- Before you check anyt hing in the engine
compartment, always read and heed all
WARNINGS
c> page 191.
(D Note
Improper hook -u p of jumper cables can r uin
the generator .
- A lways connect POS ITIV E(+ ) to POS ITIV E
( + ), and NEGATIVE( -) to NEGATIVE( -)
gro und post of the battery manager control
unit .
- Check that a ll screw plugs o n the batte ry
ce lls are screwed in firmly . If not, tighten
pl ugs prior to connect ing clamp on negat ive
battery te rminal.
- Please note that the procedure for connect­
i ng a jumper cable as desc ribed above ap ­
plies specifica lly to the case of yo ur vehicle
being jump started . W hen you a re g iving a
j u mp sta rt to another vehicl e, do
not co n­
ne ct the negative ( -) cab le to the negative
( -) t erminal o n the di scharged battery @
c> fig. 187. In stea d, secure ly co nn ect the
nega tive ( -) cab le to either a solid me tal
com ponent that is f irm ly bolted to the en ­
gine block o r to t he engine bloc k itself. I f
the battery that is being charged does not
vent to the outside , escap ing battery gas
could ignite and exp lode!
Towing with a tow truck
General hints
Y o ur Audi requires special handling for towing.
The fo llow ing information is to be used by com ­
mercia l tow truck operato rs who know how to op­
erate their eq uipment safe ly .
- Never tow your Audi, towing will cause dam­
age to the engine and transmiss ion.
- Never wrap the safety chains or winch cables
around the brake lines .
- To pre vent unnecessary damage, your Audi
must be transported with a flat bed truck.
238
- To load the vehicle on to the flat bed , use the
towing loop found in the vehicle tools and at·
tach to the front or rear anchorage
c> page 238 and c:>page 239.
A WARNING
A veh icle being towed is not safe f or passe n­
gers . Never a llow anyone to ride in a ve hicle
be ing towed, fo r any reason .
Front towing loop
Do not install the front towing loop until it is
needed .
Fig. 188 Fro nt b um per: remov ing t he cove r cap
Fig. 18 9 Front b umper: sc rew ing in t he tow ing loop
The towing loo p fits in to the threade d hole locat­
ed on the right side o f the front bum per and cov ­
e red by a small cover when not in use .
.,. Remove the tow ing loop fr om the vehicle tool­
ki t
c> page 225 .
... Press the cover i n by app lyi ng shor t strong
pressure to the bottom part to release it from
the bumper
¢ fig. 188.
... Sc rew the tow ing loop tightly into the th readed
hole as far as it will go
c> fig. 189 and tighten it
w it h the wheel w rench . ..,.

M N
0 l­oo
rl I.O
"' N
"' rl
Technical data
Vehicle identification
F ig. 195 Ve hicle Identificat io n Number (VlN) plate: loca·
t io n on d river 's s id e dash pane l
XXXXX XX -X -XXXX XXX XX
CD+ ~t :1:: xxxxxxxx xx x xx xxx xxx
T VP /fffl XXX XXX
XX XXXXXXX XX X X xx
XXX KW XXX
®i ~:J·f lfils~~ XXXX XXX XXX
®-+ ~N:a=i~ l xxxx ; xxxx xxx ; xx
II.· AUSS, I OPTIONS
,__ __
EO A 7D5
2EH JOZ
3FC
FOA
TL6 3KA
lX W
7T6 C V7
3L4 lSA 4UB
6XM 5SG
llB lA S
S M U
7Xl
9G3 OG7 OYH
8EH UlA X98
803 908 824
7K0 4X3 2 K2
4KC 3Y0 413
7GB 01 A
5RW
18A
OJF
Q Z7
020
502
4G0
XX . X XX X XX X XXXX
Fig. 196 T he veh icle identi fica tion label: ins ide the l ug·
ga ge compart men t
Vehicle Identification Number (VlN )
The Veh icle Iden tifica tion Number is located in
d iffe rent p laces:
- under the w indshield on the dr iver's side
c> fig . 195.
-in the radio or in the MM I*: Select : I CARI func­
t ion button
> V ehicle ID numb er (VIN ) or se·
Leet :
I CARI funct ion button > Car sy stem s* con­
tro l bu tton >
Servicing & checks > VIN num­
ber .
-on the vehicle identification la bel.
Technical d ata
Vehicle id entification label
T he veh icle identification label is lo cated in the
lu ggage compartment near the battery.
T he labe l c>
fig. 196 shows the fo llowing vehicle
da ta:
(D Vehicle Ident ificat ion Number (VIN)
@ Vehicle type, engine o utp ut, transmission
® Engine and transm iss ion code
@ Pa int number and interior
® Optional equipment numbers
T he information of the veh icle identification label
c a n a lso be fo und in you r W arranty
& Mai nte­
nance booklet.
Safety compliance sticker
The safety compliance sticker is you r assurance
that your new vehi cle complies w ith all applicable
Federa l Mo tor Vehi cle Safety Sta ndards which
were in effec t at the time the vehicle w as m anu ­
fac tured. Yo u can find this sticker on the door
jamb on the driver 's side. It shows the month and
year of production and the vehicle identification number of your vehicle (perforation) as we ll as
the Gross Veh icle Weight Rating (GVWR) and the
Gross Axle Weight Rating (GAWR).
H igh vo ltage warning lab el
The hig h voltage warning label is located in the
engine compartment ne xt to the eng ine hood re­
lease. The spark ign ition system complies with
the Canadian standard ICES-002 .
Weights
Gross Vehicle Weight Rating
The Gross Vehicle Weight Rat ing (GVWR), and
the Gross Axle Weight Rating (GAWR) for front
and rear are listed on a st icker on the door jamb
on the dr iver 's side.
T he Gross Vehicle Weight Rat ing includes the
weight of the basic vehicle plus fu ll fuel tank, oil
and coolant, p lus maxim um load, which includes
passenger weigh t (150 lbs/68 kg per designated
seat ing pos ition) and luggage we ight
c> .&, . ..,,.
241

M
Emergency mode . . . . . . . . . . . . . . . . . . . . . 87
Emergency release . . . . . . . . . . . . . . . . . . . . 88
K ick -down . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Manual shi ft program . . . . . . . . . . . . . . . . . 86
Remova l lock (ignition key) . . . . . . . . . . . . . 72
Selector leve r . . . . . . . . . . . . . . . . . . . . . . . . 83
Automatic wipe rs . . . . . . . . . . . . . . . . . . . . . . 50
Auto Safety Hotline . . . . . . . . . . . . . . . . . . . 119
Average speed . . . . . . . . . . . . . . . . . . . . . . . . . 24
Avoid damaging the vehicle . . . . . . . . . . . . . 17 7
B
Batte ry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
B att ery lo cati on in side the lugg age comp art-
men t .... .. .. .... .. .... ... .. .. .... . 20 1
C harge level . . . . . . . . . . . . . . . . . . . . . . . . 17 5
C harging . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Energy management ................ .
Important warn ings when wo rking on the
battery .. ...... .......... ... .. .. .. .
J ump starting ...................... .
Replacing the batte ry ...... ...... ... .
Wo rking on t he battery .............. .
Before driving 175
201
236
203
20 1
112
Belt tensioners . . . . . . . . . . . . . . . . . . . . . . . 12 7
Bio-ethanol (Fue l) . . . . . . . . . . . . . . . . . . . . . 187
Blended gasoline . . . . . . . . . . . . . . . . . . . . . 186
B lower (automa tic climate cont rol) . . . . . . . . 70
Booster seats . . . . . . . . . . . . . . . . . . . . . . . . 159
Brake fl uid
C hanging the brake fl uid . . . . . . . . . . . . . . 200
Checking the brake fluid level . . . . . . . . . . 199
B rake system
Anti-loc k bra king system . . . . . . . . . . . . . . . 1 9
Brake fl uid specifications for refill and re­
p lacement . . . . . . . . . . . . . . . . . . . . . . . . . 200
Brake light defect ive . . . . . . . . . . . . . . . . . . 21
Brake power assist unit ............... 172
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172
Ceramic brakes . . . . . . . . . . . . . . . . . . . . . . 172
Elect romechan ica l park ing brake . . . . . . . . 77
War ning/ indicato r lights . . . . . . . . . . . . . . . 15
Wo rn brake pad s symbol . . . . . . . . . . . . . . . 20
N Braking
~ Brake assist . . . . . . . . . . . . . . . . . . . . . . . . 170
; Eme rgency braking function . . . . . . . . . . . . 79
N l/'I ,....,
Index
braking guard
Messages . . .
. . . . . . . . . . . . . . . . . . . . . . 89
96
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Br eak-in per iod
Br ake pads .... .. ............. .... . .
T ires
B reaking in ........ ............... .. . 172
17
7
177
New t ires ... .. .. .. ........... .. .. .. 212
Bul bs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235
C
Californ ia Proposition 65 War ning
Battery specific 192
202
C apaci ties . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
E ngine oi l . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Cargo area
refer to Luggage compartment ..... . 64, 118
Catalyt ic converter . . . . . . . . . . . . . . . . . . . . 178
Cen ter armrest . . . . . . . . . . . . . . . . . . . . . . . . 5 7
Central lock ing . . . . . . . . . . . . . . . . . . . . . . . . 31
Central lock ing switch . . . . . . . . . . . . . . . . . 35
Convenience key . . . . . . . . . . . . . . . . . . . . . . 34
Remote contro l key . . . . . . . . . . . . . . . . . . . 34
Ceramic bra ke rotors
New brake pads . . . . . . . . . . . . . . . . . . . . . 172
Ce rtification . . . . . . . . . . . . . . . . . . . . . . . . . 24 7
Chang ing engine oil . . . . . . . . . . . . . . . . . . . 196
Checking Engine coolant level . . . . . . . . . . . . . . . . . . 197
Child rest raints
D anger of using child rest rain ts in the front
sea t............................... 130
Where can I get additional in format io n
about child restraints and the ir use? . . . . 168
Child rest raint system a nchors . . . . . . . . . . 164
Child safety . . . . . . . . . . . . . . . . . . . . . . . . . . 151
Important safety instructions for using child
safety seats . . . . . . . . . . . . . . . . . . . . . . . . 154
I n stalling a c hild restra int using th e LATCH
system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
L ower anchorages . . . . . . . . . . . . . . . . . . . 165
Moun ting and rele asing the anchorage
hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 165
T ether anchors . . . . . . . . . . . . . . . . . . . . . . 166
T ether straps . . . . . . . . . . . . . . . . . . . . . . . 166
249