2015 AUDI A5 CABRIOLET change time

Instruments and indicator Lights
the I SET! button, you delete the warning thresh­
old.
Digital clock with date display and
Odometer
Fig. 5 Instrument cluster: odometer
Fig. 6 Instrument cluster: reset button
Digital clock/GPS controlled clock*
Depending on the vehicle equipment level, you
may choose between the quartz clock or the GPS
controlled clock*~ in the radio or in the MMI*.
You can learn more about this in the MMI manual
or in the radio user's manual.
Odometer/trip odometer
The display of distance driven is shown in kilome­
ters "km" or in miles "mi".
- USA models -Miles
- Canada models - Kilometers
The units of measure (kilometers/miles) can be changed in the radio or MMI* . You can learn more
about this in the MMI manual or in the radio us­
er's manual.
The odometer @ shows the total number of kilo ­
meters or miles that have been driven on the ve­
hicle .
12
The trip odometer @ shows the distance driven
since it was last reset.
It can be used to measure
short distances. The last digit shows distances of
100 meters or 1/10 of a mile .
The trip odometer can be reset to zero by press­
ing the reset button
!O.OI ~ fig. 6.
Malfunction message
If there is a malfunction somewhere in the in­
strument cluster,
DEF will appear in the tripod­
ometer and will stay on. Contact your authorized
Audi dealer to have the problem corrected.
Immobilizer
When the ignition is switched on, the data on the
ignition key are scanned automatically.
If an unauthorized key was used,
SAFE is dis­
played permanently in the odometer display
field . The vehicle cannot be operated
¢page 30.
{i) Tips
-When you switch off the ignition or open
the driver door, the time, date, odometer
and temperature are displayed for an addi­
tional
30 seconds.
- You can also call up the display with the
!SET ! button¢ page 11 while the ignition is
switched off.
Fuel gauge
The fuel gauge works only when the ignition is on.
When the needle reaches the red area, the warn­
ing
lightliD in the instrument cluster will illumi­
nate¢
page 20. Time to refuel!
The total tank capacity of your vehicle is listed in
¢page 246.
(D Note
Never run the tank completely dry! An irregu­
lar supply of fuel can cause engine misfiring
and fuel could enter into the exhaust system.
The catalytic converter could then overheat
and be damaged.

Driver information system
Trip computer
Introduction
The trip computer gives you information on cur­
rent and average fuel mileage , average speed ,
fuel range and driving time .
Fig. 9 Trip computer d isplay: Ave rage fuel m ileage
~ 9 a: CX) m
The fo llow ing information is contin uously evalu­
ated by the trip computer and can be d isplayed
sequent ia lly in the instrument cluster display:
Fuel range
The estima ted c ruising range i n miles (km) ap­
pea rs in the disp lay . This te lls you how fa r your
ve hicle w ill be able to trave l on t he current ta nk
of fuel and with the same driv ing style. The d is­
p lay changes in increments of 5 miles (10 km) .
The cruising range is calcu lated based on t he f ue l
consumption for the last 18 m iles (30 km). If yo u
drive conse rvative ly, the cruising range will in­
crease.
Average fuel mileage
The average fuel e co nomy in MPG (l/ 100 k m)
since yo u last cleared the memory appears in this
d is pl ay. You can use this display to ad just your
driving technique to achieve a desired mileage.
Current fuel mileage
The inst antaneo us f ue l cons umption in miles per
ga llon (l/100 km) is shown in this display. Yo u
can use t his disp lay to adjust your driving techni­
que to achieve a des ired mileage .
F ue l cons umption is rec alcul ated at intervals of
33 y ards (30 me ters). Th is disp lay swit ches to
ga llons/hou r (li ters/hour) when the vehicle is not
mov ing.
24
Average speed
The aver age spee d in mph (km/ h) sin ce you last
rese t the memory appears in the display .
Elapsed time
The length of time that yo u have been d riving
s ince you last reset the memory appears in this
display .
Distance
The distance that has been covered since the last
time the memory was cleared appears i n the dis­
play .
0) Tips
-Fuel consumptions (average and current),
range and speed a re displayed in me tric
units on Canad ian mode ls .
- All stored val ues will be lost if the vehicle
bat tery is disconnected .
Memories
The trip computer is equipped with two fully au ­
tomatic memories as well as an efficiency pro­
gram* .
Fig. 10 Tri p comput er di sp la y: me mory leve l 1
You can switch between the trip computer 1 and
2 and the efficiency program* by p ressing t he
I RESET I button @<=> page 25, fig. 11 .
You can tell wh ic h memory leve l is currently ac­
tive by the number o r the sig n in the display
Q fig. 10. The data from the single-t rip memory
(memo ry leve l 1) is being d isplayed if a
D ap­
pears in the display. If a
fJ is shown, t hen the da-
ta from the total-t rip memory is being d isp layed .,,_

M N
ci u.. co ,...., \!) 1.1'1
N 1.1'1 ,....,
messages appear automatically and are only dis­
p layed in the efficiency program . The fuel econo ­
my messages turn
off automatically after acer­
tain period of time.
.. To turn a fuel economy message
off immed iate ­
l y after it appears, press the I RESET
I b utton
¢ page 25, fig. 11 @ , or
.. Press the function selection switch¢
page 25,
fig. 11
@ .
(D Tips
-Once you have t urned a fuel economy mes­
sage
off, i t will only appear aga in after you
turn the ignit ion on again.
- The fuel economy messages are not dis­
played in every instance, but rather in inter­
vals over a per iod of t ime .
Service interval display
The service interval display reminds you when
your next service is due .
Fig. 1 5 Dis p lay: Service interval d isp lay
~ 0 ci:
"' a,
The sc hed ule for the next oil c hange or inspec ­
tion is calculated a utomatically and displayed ac ­
cordingly. The display works in two stages :
Service reminder
30 days before the nex t servi ce is due, a serv ice
reminde r appea rs in the disp lay when you tu rn on
the ignition
¢ fig. 15.
Afte r about 5 seconds the display sw itches back
t o no rma l. The dis tan ce and t ime rem aining are
updated eac h time the ignition is turned on unti l
the date due for service is reached .
Driver information s ystem
Service due
When the d ue date for se rvice is reached, t he
message
Service due! appears in the inst rument
cluster immediate ly afte r yo u turn on the igni­
tion . Additiona lly, a warning tone sounds. Afte r
about 5 seconds the display switches back to nor ­
mal.
Calling up the service schedules
If or when an oi l change or inspection is due, can
be shown in t he radio or
M MI* dis play by select­
ing the service interval display in the ca r men u.
Se lect I CAR I funct ion button >
Service interval
display
or ICARI function button > Car systems *
control button > Servicing & checks .
Resett ing the service interval display
Your a uthorized Audi dea ler will reset the corre­
sponding service schedule after performing the appropriate service on your vehicle. You also have
the possibility to reset the oil change schedule af­
ter having performed an oi l change according to
Audi specifica tions . Select I CAR ! funct ion button
> Service interval display > Res et oil change in­
terval
o r! CARlfunction button> Car systems*
control b utton > Servicing & check s > Reset oil
change inter val.
(D Note
- Only re se t the oil change display when yo u
h ave comple ted an o il change.
- If you disconnect the batte ry termina ls, no
c al cul ations can be made for the se rv ice in­
t erval disp lay during t his time and n o serv ­
ice reminder w ill appea r. R emembe r that
observing the p ro p er service interva ls is vi­
tally impo rtant to exten ding the life of yo ur
vehicle, part icular ly the eng ine, and main­
taining its va lue. Even if the mileage dr iven
is low, the maxim um per iod of one year
from one service to t he nex t must not be ex­
ceeded.
(D Tips
The information in the Service Reminder re­
mains stored even when th e vehicle battery is
disco nnecte d.
27

M N
ci LL co
rl I.O
"' N
"' rl
-Do not remove the key from the ignition lock
until the vehicle has come to a complete
stop. Otherwise the steering column lock
could suddenly engage -causing the risk of
an acc ident.
(D Tips
- The operation of the remote control key can
be temporar ily disrupted by interference
from transmitters in the vicinity of the vehi­
cle work ing in the same frequency range
(e .g. a cell phone, rad io equipment) .
- For security reasons, replacement keys are only available from author ized Audi dealer.
- For Declarat ion of Compliance to United
States FCC and Industry Canada regulations
<::;>page 251.
Removing the mechanical key
F ig. 18 Remote maste r key: remov ing the mechanical key
.,. Press the release button @ i:> fig. 18 .
.,. Pull the mechan ical key @ out of the master
key .
Using the mechan ical key, you can:
- lock and unlock* the glove compartment on the
passenger's side
i:> page 65 .
-lock and unlock the vehicle manually
i=> page 34 if this should not be possible w ith
the master key.
- use the ignition key emergency release
i=>page 32.
Open ing and clo sing
Check light and battery in the master key
Fig. 19 Remote master key: removing th e battery holder
Check light in the master key
The check light @i=> fig. 19 in the master key
provides information about different conditions.
.,. The check light turns on briefly once when a
button is pressed, and during an "inquiry" by
the convenience key system.
.,. If the check light does not come on, the battery
is dead and has to be replaced. In addit ion,
when the battery is dead the
!I i ndicator light
appears in the instrument cluster d isp lay as
well as the message
Pl ea se change k ey bat­
tery .
Master key battery replacement
.,. Remove the mechan ical key i:> page 31 .
.,. Press the release button@~ fig. 19on the bat·
tery ho lder and at the same time pull the bat­
tery ho lder out of the maste r key in the d irec­
tion of the arrow .
.,. Insta ll the new battery CR 2032 with the"+"
sign facing down .
.,. Push the battery holder carefu lly into the mas·
ter key.
.,. Insta ll the mechanical key.
@) For the sake of the env ironment
Dispose of dead batteries properly so as not
to pollute the environment.
@ Tips
The replacement battery must be the same
spec ificat ion as the origina l.
31

Lights and Vision
The coming home and leaving home functions
only operate when it is dark and the light switch
is in the AUTO position ¢
page 50, fig. 54.
Auto headlights*
When the light switch is in the AUTO¢ page 50
position, the switch-on point of the lights can be
changed in the automatic driving light function.
Daytime running lights
USA models:
You can switch the daytime running
lights
on and off.
Canada models:
The function cannot be turned
off. It is activated automatically each time the ig­
nition is switched on.
Travel mode*
The headlight beam is asymmetrical. This pro­
vides stronger illumination on the side of the
road on which you are driving. If you are driving
in a country that drives on the opposite side of
the road from your own country, this will cause
glare for oncoming drivers. To prevent glare:
- Travel mode must be selected in vehicles with
Xenon headlights* .
- In vehicles with halogen headlights, certain
areas of the headlight lenses must be covered
with waterproof adhesive covers that prevent light from passing through. For more informa ­
tion, please see your authorized Audi dealer or authorized repair facility.
When travel mode is activated, a display in
the driver information system indicates this
each time you switch the ignition on.
52
Emergency flashers
Fig. 56 Center console: emer gency flasher switch
The emergency flashers makes other motorists
aware that you or your vehicle are in an emergen­
cy situation .
.. Press the switch ~¢
fig. 56 to t urn the emer-
gency flashers on or off.
When the emergency flashers are on, all four
turn signals blink at the same time. The turn sig­
nal indicator lights
RB in the instrument clus­
ter, as well as the light in the emergency flasher
switch
IA] blink likewise .
You can indicate a lane change or a turn when the
emergency flashers are switched on by using the
turn signal lever . The emergency flashers stop
temporarily .
The emergency flashers also work when the igni­
tion is turned off.
The emergency flashers will turn on automatical­
ly if you are in an accident where the airbag has
deployed.
@ Tips
You should turn on the emergency flashers
when:
-you are the last vehicle standing in a traffic
jam so that any other vehicles coming can see you, or when
- your vehicle has broken down or you are in
an emergency situation, or when
-your vehicle is being towed by a tow truck or
if you are towing another vehicle behind
you.

M N
ci u.. co ,...., \!) 1.1'1
N 1.1'1 ,....,
Automatic transmission
multitronic, S tronic,
tiptronic
Introduction
Appl ies to vehicles: with multitronic/5 tronic/tiptronic
The automatic transmission is controlled elec­
tronically. The transmission upshifts or down­
shifts automatically depending on which drive
program is se lected.
When a
moderate driving style is used, the
transmission selects the most economica l driving
mode. It will then change up early and delay the
downshifts to give better fuel economy .
The transmission switches to a sporty mode after
a kick-down or when the driver uses a
sporty driv­
ing style
characterized by quick accelerator pedal
movements, heavy acceleration, frequent
changes in speed and traveling at the maximum
speed .
If desired, the driver can also se lect the gears
manually (tiptronic mode) q page 83.
Various automatic transmissions may be instal­
led, depending on the model:
multitronic transmission
The multitronic transmission is a continuously
variable transmission. Power is transferred using
a mu ltidisk clutch. In contrast to conventional
automatic transmissions using shifting opera­
tions, the transmission ratio in the continuously
variable transmission is changed continuous ly.
This optimi zes the comfort level and conserves
fuel.
S tronic transmission
The 5 tronic is a dual-clutch transmission. Power
is transferred using two clutches that work inde­
pendently from one another. They replace the
torque converter used in conventional automatic
transmissions and allow the vehicle to accelerate
without a noticeable interruption in traction .
tiptronic transmission
In the tiptronic transmission, power is transfer­
red by a torque converter.
Automatic transmission
Selector lever positions
Applies to vehicles: with multitronic/S tronic/tiptronic
Fig. 96 Disp lay in the instrument cluster: selec tor lever in
position P
T he selector lever position engaged appears next
to the se lector lever as well as in the instrument
cluster display.
P -Park
In this se lector lever position the transmission is
mechanically locked . Engage P only when the ve­
hicle is
completely stopped~.&. in Driving the
automatic transmission on page 86.
To shift in or out of posit ion P, you must first
press and hold the brake pedal and then press
the release button in the selector leve r handle
whi le moving the selector lever to or from P. You
can shift out of this position only with the igni­
tion on.
R - Reverse
Select R only when the vehicle is at a full stop
and the engine is running at idle speed~ .&. in
Driving the automatic transmission on
page 86 .
Before you move the selector lever to R, press
both the release button in the hand le of these­
lector lever
and the brake pedal at the same
time .
When the ignition is on, the backup lights illumi­
nate when the selector lever is moved into R.
N -Neutral
The transmission is in neutral in this position .
Sh ift to this position for standing with the brakes
applied
~ .&. in Driving the automatic transmis-
sion on page 86. .,.
83

Audi adaptive cruise control and braking guard
Audi adaptive cruise
control
De script ion
Applies to veh icles: with Audi adaptive cruise co ntrol
F ig. 106 Detect ion range
What can Audi adaptive cruise control do?
The adaptive cruise control works in conjunction
with a radar sensor instal led in the front of the
vehicle
¢ page 90, fig. 103, which is subject to
designated system limits¢
page 92. Stationary
objects are disregarded.
On open roads w ith no traff ic, adaptive cruise
control works like a regula r cruise control system.
The stored speed is mainta ined . When approach­
ing a moving vehicle detected up ahead, the
adaptive cruise control system automatically
slows down to match that vehicle's spe ed and
then maintains the distance that the d river previ ­
ously stored. A s soon as the system does not de­
t ec t a vehicle up ahead, adap tive cruise control
accelerates back up to the stored speed .
Which functions can be controlled?
When you switch adaptive cruise control on, you
can set the current speed as the "control speed"
¢ page 92 , Swit ch ing on and off.
When driving, you can stop cruise control
¢
pag e 94 or change the speed ¢ page 93 at
any time.
You can a lso set the distance to the object ahead
and set the adaptive cr uise control driving pro­
gram
¢ page 94.
92
Switch ing on and off
Applies to vehicles: with A udi adaptive cruise contro l
Fig. 107 Selector le ve r: switc hin g o n/off
Fig. 108 I ns trume nt cl ust er: Au di ada ptive cruise control
You can set any speed between 20 mph and 95
mph (30 and 150 km/h).
Indicator lamps and messages in the instrument cluster display inform you about the current sys­
tem status and settings.
Switching Audi adaptive cruise control on
.. Pull the lever toward you into position (D
¢ fig. 107 . ACC standby appears in the instru ­
ment cluster display .
Setting the speed and activating regulation
.. To set the current speed, press the ISET I button
¢
page 11, fig. 4. The set speed is shown in the ..,.

Audi adaptive cruise control and braking guard
Interrupting cruise control
Applies to veh icles: w ith Audi adaptive cruise co ntrol
Fig. 110 Selector leve r
Requirement : adaptive cruise control must be
switched on
¢ fig . llO (i).
Overriding cruise control
• To accelerate manually, press the acce lerator
pedal. The message
ACC override appears .
• To resume adaptive cruise control, remove your
foot from the gas pedal. The system returns
again to the speed that was saved before.
• You can save a new speed at any time by press·
ing the
ISETI button r:::;, page 11, fig. 4.
Canceling cruise control while driving
• Move the lever into position @. The message
ACC standby appears . Or
• press the brake pedal.
• To resume the stored speed, move the lever in­
to position
@ .
,& WARNING
Never resume the stored speed if the speed is
too high for prevailing road, traffic or weather
conditions.
94
Setting the distance
App lies to vehicles: wit h Audi adapt ive cru ise contro l
Fig. 111 Selector lever: setting the d istance
• Tap the switch to display the current set dis­
tance
¢ fig . 111 .
• To increase or reduce the distance by incre·
ments, tap the switch again to the left or right.
The distance between the two veh icles will
change in the instrument cluster display .
When approach ing a mov ing vehicle up ahead,
the adapt ive cruise control system brakes to
match that object's speed and then mainta ins
the stored distance. If the vehicle ahead acceler­
ates, adaptive cruise contro l will also accelerate
up to the stored speed.
The higher the speed, the greater the distance in
yards (meters)
r:::;, A . The Distance 3 setting is
recommended.
The distances prov ided are specified va lues . De ­
pending on the driving situation and the how the
vehicle ahead is driving, the actua l dis tance may
be more or less than these target distances.
The var ious symbols for the time increments ap­
pear briefly in the information line@r:::;,
page 92,
fig. 108 when you change the settings .
o;:'.'.:>_o;:'.'.:> ___ Distance 1: This setting corresponds
to a distance of 92 feet/28 meters when travel·
i ng at 62 mph (100 km/h), or a time i nterva l of 1
second.
o;:'.'.:> __ o;:'.'.:> __ Distance 2: This setting corresponds
to a distance of 118 feet/36 meters when travel ­
i ng at 62 mph (100 km/h), or a time i nterva l of
1.3 seconds.