2015 AUDI A5 CABRIOLET lock

Power top
Step S: Retracting the power top
compartment cover
"' 0 ,.... ~
" "' U)
Step 7: Loosening the headliner
Fig. 51 Rear w indow: loosening the right side of the head-
Fig. 49 Rear of vehicle: retracting the power top com part· liner
ment cover
.. Raise the rear of the power top and hold it in
place @
¢ A in General information on
page 46 .
.. Slide the power top compartment cover for­
ward @until it reaches the end position . Re­
lease the powe r top .
Step 6: Locking the power top
Fig. SO Inside of the power top: locking the power top
.. Insert the emergency release key into the open­
ing
¢ page 47, fig. 46 .
.. Turn the emergency release key clockw ise until
it stops to lock the power top .
.. Remove the emergency release key and in stall
the cap in the opening.
(D Tips
Make sure the lockin g mechanisms are lock ed
securely.
48
Fig. 52 Rear window: headliner partially loosened
Perform the follow ing steps at the rear of the ve­
hicle on both sides of the power top .
.. To loosen the headliner , ra ise the rear of the
power and pull on the yellow loop
¢ fig. 51
with t he eme rgency release key .
.. Continue pulling on the loop to loosen the
headl iner around the rear window (approxi­
mate ly 30 cm)
¢ fig . 52 .
Step 8: Securing the latch
Fig. 53 Rear of the power top: securing the latc h
Lock the latch on both sides of the vehicle .
... N N
:r (0 U)

M N
ci u.. co ,...., \!) 1.1'1
N 1.1'1 ,....,
~ Pull the power top headliner to the side in the
area by the rear head restraints¢
fig. 53.
~ Insert the short end of the emergency re lease
lever in the ye llow sleeve on the power top sup­
port
¢ fig . 53.
~ Turn the emergency release key in the direction
of the arrow @until the support is locked .
~ Put the emergency release key away @
¢ page 46, fig. 43.
Power top
49

M N
ci LL co
rl I.O
"' N
"' rl
the windshield in this a rea in order to
prevent malfunctions or failures .
- Some exterior lighting functions can be ad­
ju ste d~
pa ge 51 .
-When yo u remove your key from the igni tion
while the vehi cle's ligh ts are turned o n, a
buzzer sounds as long as t he driver 's door is
open.
- In coo l o r dam p weather, t he inside of the
h eadlights, turn sig nals and tail lights can
fog over d ue to the temperature difference
between the inside and outs ide. They will
clea r shortly after switching them on. T his
does not affect t he service li fe of the light­
i ng.
- In the event of a light sensor malfunction,
the driver is not ified in the instr ume nt clus­
te r display~
page 21.
Turn signals and high beam lever
The lever operates the turn signals, the high
b eams and the headlight flasher.
Fi g. 55 Tu rn signa l and high beam lever
Turn signals ¢ Q
g N
0
~ CD
The turn signals activate when you move the lev­
er into a turn s ignal position when the ignition is
switched on.
@ -righ t tur n signal
@ -left turn signa l
The turn s ignal b links three times if you just tap
the lever.
High beams and headlight flasher
[0
M ove the lever to the corresponding position:
@ -high beams o n
Lights and Vis ion
@ -high beams off or headlight flasher
T he ind icator light
II in t he inst rument cl uste r
tu rns on.
Notes on these features
- The
turn signals on ly wor k w ith the ign ition
tur ned on. The indicator ligh ts . or
II in the
instr um ent clus ter also b link.
-After you have tu rned a corner, the turn s ignal
sw itches off automatically.
- The
high beam works on ly when the headlights
are on . T he indicator light
II in the instrument
cluste r illuminates whe n the high beams a re
on.
- The
headlight flash er works o nly as long as yo u
hold the leve r - even if there are no lights
sw itched on . The indica to r li ght
II in the in­
s trumen t cluste r ill umin ates when you use t he
head light flasher.
,&. WARNING
D o not use t he h igh beam or hea dlight flashe r
i f you know that these could blind oncoming
traffic.
Adjusting exterior lighting
The func tions are selected in the radio or MMI* .
.,. Select: !CAR I func tion b utton > Exterior light­
ing .
Or
.,. Sele ct: !~C_A _R~ I function b utton > Car systems *
contro l butto n > Vehicle settings > Exterior
lighting .
Coming home (light when leaving car )*,
Leaving home (light when unlocking car)*
The
coming home f u nction illuminates the area
aro und t he vehicle when the ignition is switched
off and the driver's door is opened. Depend ing on
vehicle equipment, the function can be switched o n and off o r the length of t ime t he lig hts rema in
on* can be adjusted .
The
leaving home function illuminates t he area
around th e vehicle when unloc kin g it. This func-
t ion can be switched on and off. ""
51

Lights and Vision
Q/P -Adjusting the left/right exterior mirror .
Move the knob in the des ired direction.
4ill -Heat ing the m irror g lass depending on the
outside temperature*.
.9 -Folding exterior mirrors* . In the Infotain­
ment system, you can select if the mirrors fold in
automatically when you lock the vehicle
¢ page 34.
Front passenger's exterior mirror tilt
function*
To help you see the curb when backing into a
parking space, the surface of the mirror t ilts
slightly . Fo r this to happen, the knob must be in
the position for the front passenger 's outside
mirror.
You can adjust the tilted mirror su rface by turn­
ing the knob in the des ired direction . When you
move out of reverse and into another gear, the
new mirror position is stored and assigned to the
key you are using.
The mirror goes back into its origina l position
once you drive forward faster than 9 mph (15 km/h) or turn the ignition off.
A WARNING
Curved mirror surfaces (convex or spherical*)
increase your field of view. Remember that
vehicles or other objects will appear smaller
and farther away than when seen in a flat mir­
ror. If you use this mirror to estimate distan­
ces of following vehicles when changing
lanes, you cou ld estimate incorrectly and
cause an accident.
(D Note
-If the mirror hous ing was moved by force
(for example, by running into an object
when maneuvering the vehi cle), the mirror
must be folded all the way in using the pow­
er folding function. The mirror housing
must not be moved back into place by hand
because this would impair the function of
the mirror mechanism.
- If you wash the vehicle in an automatic car
wash, you must fold the exterior mirrors in
54 to reduce
the risk of damage to the mirrors.
Never fold power folding exterior mirrors*
by hand. Only fold them in and out using
the power controls.
(D Tips
-If the power adjusting function malfunc­
tions, the g lass in both mirrors can be ad ­
justed by pressing on the edge of it by hand.
- The exterior mirror settings are stored with
the memory function* ¢
page 63.
Dimming the mirrors
Fig. 61 Auto mat ic dimmin g rearv iew mirro r•
Manual dimming rearview mirror
.,. Pull the lever on the bottom of the m irror back .
Automat ic dimming rearview mirror*
.,. Press the button@¢ fig. 61. The indicator
light @ turns on . The rearview and exter ior*
mirrors dim automatically when light shines on
them, for example from headlights on a vehicle
to the rear.
~ WARNING
Electro lyte fluid can leak from automatic dim­
ming mirrors if the glass is broken. Electrolyte
fluid can irritate skin, eyes and respiratory system.
- Repeated or prolonged exposure to e lectro­
lyte can cause irritation to the respiratory
system, especially among people with asth­
ma or other resp iratory conditions . Get
fresh a ir immediately by leaving the vehicle
or, if that is not possible, open windows and
doors all the way.
~

M N
ci LL co
rl I.O
"' N
"' rl
.. Select: ICARI function button> Car systems*
control button > Servicing & checks > Wiper
service position
> On/Off .
Removing the wiper blade
.. Lift the windshie ld wiper arm up from the wind­
shield.
.. Press the locking knob
@¢fig . 64 on the wiper
blade. Hold the wiper b lade firm ly.
.. Remove the wiper blade in the direction of the
arrow .
Attaching the wiper blade
.. Install the new wiper blade in the retainer on
the wiper arm@ unti l you hear it click into
place on the wiper arm .
.. Place the wiper arm back on the windshie ld.
.. Turn the service pos ition off.
A WARNING
For your safety, you should replace the wiper
blades once or twice a year. See your author­
ized Aud i dea ler for replacement blades.
(D Note
-The windshield wiper blades must only be
replaced when in the service position! Oth­
erwise, you r isk damaging the paint on the
hood or the windshield wiper motor.
- You should not move your vehicle or press
the windshie ld w iper lever when the wiper
arms are folded away from the windshield .
The windshield wipers would move back in­
to their original position and could damage
the hood and windshield.
- To he lp prevent damage to the wiper sys­
tem, always loosen blades which are frozen
to the windshie ld before operating wipers .
- To he lp prevent damage to w iper blades, do
not use gasoline, kerosene, paint thinner, or
other solvents on or near the wiper blades.
- To he lp prevent damage to the wiper arms
or other components, do not attempt to
move the wipers by hand .
Lights and Vision
(D Tips
-Commercial hot waxes applied by automatic
car washes affect the how easily the glass
surface can be cleaned.
- You can also use the service position, for ex­
ample, if you want to protect the windshield
from icing by using a cover .
Digital compass
Switching the compass on and off
Appl ies to veh icles : w ith dig it a l co mp ass
The compass direction is shown in the rearview
mirror.
Fig. 65 Rearv iew mirr or: Digita l compass act ivated
M
-
.. To switch the compass on or off, press and hold
the button @ unti l the compass d isplay in the
mirror¢
fig. 65 appears or disappears.
The digita l compass only works when the ignition
is on. The directions are indicated with abbrevia­
tions: N (north), NE (northeast), E (east), SE
(southeast),
S (south), SW (southwest), W
(west), NW (northwest) .
@ Tips
To prevent inaccurate compass readings, do
not bring any remote controls, electrical devi­
ces or metallic objects near the mirror .
57

Seats and storag e
Center armrest
The center armrest can be adjusted to several
levels.
F ig . 70 Armrest between t he driver's/front passenger's
seats.
Adjust ing the cente r armre st
.. To adj ust the angle, raise the armrest from the
starting posit ion ¢
fig. 70 detent by detent .
.. To bring the armrest back into the starting po­
s ition, raise it out of the top detent and fold it
back down.
The armrest can slide forward and back .
Head restraints
Front head restraints
Applies to veh icles: with ad justable head restraints
Head restraints that are adjusted according to
body size, along with the seat belt, offer effec­
tive protection .
Fig. 7 1 Front seat: adjusting the manual head restra ints
62
Fig. 72 Front seat: adjusting the power head rest rai nt
Adjust the head restraint so the upper edge is as
even as possible with the top of you r head .
If that
i s not possib le, try to adjust the head res traint so
that it is as close to th is position as possible
¢ page 62.
.,. To adjus t the height of the manual head re­
straint *, gr ip the head restra int on the sides
with both hands and slide it up/down until it
locks into place
¢fig. 71.
.. To adjust the height of the power head re-
straint*, press the button up/down ¢
fig. 72.
Refer to ¢ page 116, Proper adjustment of head
restraints
for guidelines on how to adjust the
height of the front head restraints to s uit the oc­
cupant's body size.
A WARNING
-Dr iving without head restraints or with head
restraints that are not properly adjusted in­
creases the risk of ser ious or fatal neck in­
jury dramat ically.
- Read and heed all WARNINGS¢
page 116,
Proper adjustment of head restraints.
@ Tips
- To prevent the head restraints from running
into the head liner, they retract automat ica l­
ly when moving the seat fo rward o r upward .
- Correctly adjusted head restraints and safe­
ty be lts a re an extreme ly effect ive comb ina­
t ion of safety features.

M N
ci LL co
rl I.O
"' N
"' rl
Memory function
Description
Applies to vehicles: with memory function
The memory function allows you to quick ly and
eas ily store and recall personal seating profiles
for the driver. The memo ry function is operated
through the master key and the memory buttons
in the driver's door.
The driver's seating profile is stored and assigned
to the master key each time the veh icle is locked.
When you open the door, the seat profile is auto­
matically recalled. If two people use one vehicle,
it is recommended that each person always uses
"their own" master key.
Up to 2 seat profiles can be stored in the memory
buttons in the driver's door. Once they are stored,
these seat profiles can be selected at any time .
I n addition to the driver's seat settings, you can
also store and access the exterior mirror adjust­ ment settings* using the remote control key or
memory button.
Remote control key
Applies to vehicles: with seat memory
To assign the driver's seat settings to the remote
control key when locking the vehicle, the function
must be activated in the radio or
MM!*
• Select: I CARI function button > Seat adjust·
ment > Driver's seat > Remote control key
>
on .Or
• Select: ~IC _A _ R~I function button> Car systems*
control button > Vehicle settings > Seats >
Driver's seat> Remote control key> On .
(D Tips
If you do not want another driver's settings to
be assigned to the remote key, switch off the
memory function using the radio or
MMI* or
the
I ON/OFF I button ~ page 63.
Seats and storage
Memory buttons
Applies to vehicles: with seat memory
Fig. 73 Driver's door: memory func tion buttons
The memory buttons are located in the driver's
door.
Switching the memory function on/off
.,. Press the ION/OFF ! button to switch the memo­
ry function on/off. The word
OFF lights up when
the memory function is switched off. Seat pro­
files are neither stored nor recalled .
Storing a seat profile
.,. Press the ISETI button. When the word SET
lights up, the memory is ready to store set­
tings.
• Press a memory button
(ill or [II) briefly. A tone
confirms that the settings were stored.
Accessing a seat profile
.,. If the driver's door is open and the ignition is
switched off, press the memory button .
.,. If the driver's door is closed or the ignition is
switched on, press and hold the memory but­
ton until the seat adjustment is complete.
.8, WARNING
- For safety reasons, the seat setting can only
be recalled when the vehicle is stationary -
otherwise you risk having an accident.
- In an emergency the recall procedure can be
cancelled by pressing the
ION/OFF I switch or
by tapping the memory buttons.
63

M N
ci LL co
rl I.O
"' N
"' rl
(upholder
Fig. 76 Center console: front cupholder
Fig. 77 (upholder• in the rear
Front beverage holders
.. You can accommodate two beverages in thi s
storage ¢
fig. 76.
A maximum of two beverages can be placed in
the rear beverage holders* .
A WARNING
Spilled hot liquid can cause an accident and
personal injury.
- Never carry any beverage containers with
hot liquids, such as hot coffee or hot tea, in
the vehicle while it is moving. In case of an
accident, sudden braking or other vehicle
movement, hot liquid could spill, causing
scalding burns. Spilled hot liquid can also
cause an accident and personal injury.
- Use only soft cups in the cupholder. Hard
cups and glasses can cause injury in an acci­
dent.
- Never use the cupholder or adapter as an
ashtray -risk of fire.
Seats and storage
(D Note
Only drink containers with lids should be car­
ried in the cupholder. Liquid could spill out
and damage your vehicle's electronic equip­
ment or stain the upholstery, etc.
Glove compartment
The glove compartment is illuminated and can
be locked.
Fig. 78 Glove compart ment
.. To open the glove compartment, pull the han­
dle in the direction of the arrow ¢
fig. 78 and
sw ing the cover down to open .
.. To close the glove compartment, push the
glove compartment lid upward until the lock
engages.
The glove compartment can be locked using the
mechanical key¢
page 31.
On the right side in the glove compartment is a
holder with the key body into which the emergen­
cy key must be clipped to be able to start the ve­
hicle.
A WARNING
To reduce the risk of personal injury in an acci­
dent or sudden stop, always keep the glove
compartment closed while driving.
Luggage compartment
General information
A WARNING
-
Read and follow the important safety precau­
tions on ¢
page 118, Storing cargo correctly.
65