2015 AUDI A4 checking

216 Checking and filling
-If you have the impression your engine
consumes excessive amounts of oi l, we
recommend that you consult an author­
ized Audi dealer to have the cause of
your concern properly diagnosed. Keep in
mind that the accurate measurement of
oil consumption requires great care and
may take some time . An authorized Audi
dealer has instructions about how to
measure oil consumpt ion accurately.
Checking the engine oil level
Fig. 183 MMI D isp lay : Oil leve l ind icator
Read oil level
.,. Park your vehicle so that it is horizonta lly
level.
.,. Shut the engine off when it is at operat ing
temperature .
.,. Switch only the ignition back on.
• Wait approx . two minutes.
• Se lect : Fu nct ion button
I _C_A_R_I > Oil level. Or
.,. Select : Function button
ICARI > Car sys-
tems* control button > Servicing & checks >
Oil level.
.,. Read the oil Level in the MMI* Display
c:> fig. 183. Add engine oi l if the bar of the
oil level indicator is near "min"
c:> page 216
Depend ing on the way the vehicle is driven
and the operating conditions, oil consumpt ion
can be up to a 1/2 quart per 600 mi les (0.5
li­
ter per 1,000 km) . Consumption may be high­
er within the first 3,000 miles (5 ,000 km).
(D Tips
The oil Level indicator in the MMI* Display
is only an information display . If the oil
Level is too Low, a minimum oil warning ap -pears in
the instrument cluster. Add oil
c:> page 216. If the hood has been opened,
the current oil level is shown in the instru­
ment cluster the next t ime the ignition is
switched on.
'e:;1: Adding engine oil
Fig. 184 Engin e compar tmen t: Cover on th e oil filler
neck
.,. Before you check anything in the engine
compartment,
always read and heed all
WARNINGS c:> .&. in Working in the engine
compartment on page 212 .
.,. Shut the engine off .
.,. Unscrew the cap
't'::71 to the engine oi l filling
hole
¢ fig. 184, c:>page 214, fig. 182 .
.,. Carefully top off with 0 .5 quarts (0 .5 liters)
of the appropriate oil
c:> page 214 .
• Check the oil level again after two minutes
r::;, page 216, Checking the engine ail level .
.,. Top off the oil aga in , if necessary .
.,. Screw the cap back on the filling hole .
_& WARNING
-While topping off, the oil must not come
i n contact with hot engine parts -fire
hazard!
- The oil filler cap must be properly se­
cured to prevent oil from being sprayed
on the hot engine and exhaust system
when the engine is running -fire hazard!
- If your skin has come in contact with the
engine o il, you must subsequently
cleanse it thoroughly.
(D Note
- Check the oil level using the radio or
MMI*. If the message Please reduce oil

218 Check ing and filling
Engine cooling system
Coolant
The engine coolant performs two functions: it
keeps the engine from overheating and it pro ­
tects the engine from freezing in the winter .
The cooling system is sealed and generally re­
quires little attention.
The cooling system has been filled at the fac­
tory with a permanent coolant which does not need to be changed. The coolant consists of a
mixture of specially conditioned water and the
manufacturer's glycol-basedcoolant addi-
tive G13 antifreeze with ant icorrosion addi­
tives (50% for USA models; 60% for Canadian models) . This mixture both assures the neces­
sary frost protection and protects metal com­
ponents in the engine's cooling system from
corrosion and scaling.
It a lso raises the boil­
ing point of the coo lant.
Do not reduce the concentration of the coo l­
ant in the summer by adding plain water .
The
pr opor tion of coolant add itiv e m ust be at
l eas t 50% but not more than 60%
to main­
tain antifree ze protection and cooling efficien­
cy. If the coolant frost protection is too low,
the coolant could freeze and damage the veh i­
cle heating and eng ine cooling system .
For year-round driving, antifree ze is added at
the factory for temperatures down to:
- -31°F(-35°C)USA
- - 40 ° F ( - 40 °C) Canada.
I f you must add coo lant, use a m ixture of wa­
ter and coolant addit ive. M ixing the coolant
addit ive with dist illed water is recommended.
_& WARNING
Before you check anything in the engine
compartment, always read and heed all
WARNINGS
~ &. in Working in the engine
compartment on page 212.
(D Note
- Before winter sets in, have the coolant
checked to see if the coolant additive in
-
your vehicle is sufficient to meet the cli­mate conditions . This is especia lly impor­
tant if you live in a reg ion where the win­
ter is extreme ly cold. If necessary, in­
crease the proportion of coolant additive
to 60% .
- When adding coolant additive to your
cooling system, remember :
- We recommend us ing on ly coolant ad­
d itive G12 ++ or G13 for your vehicle.
This coolant addit ive is availab le at a u­
thorized Audi dealers. Other types of
antifreeze can significantly reduce cor­ rosion protection. The resulting corro­
sion can cause a loss of coolant and se­
rious engine damage .
- Do not add any type of radiator leak seal­
ant to your vehicle's engine coolant.
Add ing radiator repa ir flu id may adverse ­
ly affect the function and performance of
your cooling system and could resu lt in
damage not covered by your New Veh icle
Limited Warranty.
Checking the engine coolant level
The engine coolant level can be checked with
a quick glance.
F ig . 1 85 Engine compar tmen t: Cover on the coo la n t
expans io n t ank
.,. Before you check anything in the engine
compa rtment,
alwa ys read and h eed all
W ARNING S ~ ,& in Working in the engine
compartment on page 212.
.,. Park your vehicle on a level surface .
.,. Turn off the ignition.
.,. Read the engine coolant level from the coo l­
ant expansion tank
c:> fig . 185, c:> page 214,
fig . 182.
With a cold engine, the coolant Iii>-

'"" N
0 ::.,: co ,...., \!) ..,.,
,...., ..,., ,....,
level should be between the "MIN" and
"MAX" markings. When the engine is warm,
the level may be slightly above the "MAX"
marking .
The location of the coolant expansion tank
can be seen in the engine compartment illus­
tration
<=> page 214.
To obtain an accurate reading , the engine
must be switched
off.
The expansion tank in your vehicle is equipped
with an electric coolant level sensor.
When the coolant level is too low, the warning
light in the Auto-Check System <=>
page 17 will
blink until you add coolant and the level has
been restored to normal. Even though there is
an electric coolant level sensor, we still rec­
ommend you check the coolant level from
time to time.
Coolant loss
Coolant loss may indicate a leak in the cooling
system. In the event of coolant loss, the cool­
ing system should be inspected immediately
by your authorized Audi dealer.
It is not
enough merely to add coolant.
In a
sealed system, losses can occur only if
the boiling point of the coolant is exceeded as
a result of overheating.
A WARNING
The cooling system is under pressure and
can get very hot. Reduce the risk of scald­
ing from hot coolant by following these
steps.
- Turn
off the engine and allow it to cool
down.
- Protect your face, hands and arms from escaping fluid and steam by covering the
cap with a large, thick rag .
- Turn the cap slowly and very carefully in
a counter-clockwise direction while ap­
plying light, downward pressure on the
top of the cap .
- To avoid being burned, do not spill anti­
freeze or coolant on the exhaust system
Checking and filling 219
or hot engine parts. Under certain condi­
tions, the ethylene glycol in engine cool­
ant can catch fire.
([) Note
Do not add any type of radiator leak seal­
ant to your vehicle's engine coolant. Add- ing radiator repair fluid may adversely af­
fect the function and performance of your
cooling system and could result in damage
not covered by your New Vehicle limited
Warranty .
Adding coolant
Be very careful when adding engine coolant.
Before you check anything in the engine com­
partment ,
always read and heed all WARN­
INGS <=>
A in Working in the engine compart­
ment on page 212 .
Requirement: There must be a residual
amount of coolant in the expansion tank <=>(D.
.,. Turn
off the engine.
.,. Let the engine cool down.
.,. Place a thick rag over the coolant expansion
tank
<=> page 218, fig . 185 and carefully turn
the cap counter-clockwise
<=> .&_ .
.,. Add coolant mixed in the correct ratio
<=> page 218, Coolant up to the MAX mark­
ing.
.,. Make sure that the fluid level remains sta-
ble. Add more coolant if necessary.
.,. Twist the cap on again
tightly.
Replacement engine coolant must conform to
exact specifications <=>
page 218, Coolant.
We recommend using only coolant additive
G12 ++, G13 or in an emergency G12 +. Do
not
use a different additive. In an emergency use
plain water until you can get the correct addi­
tive and can restore the correct ratio. This
should be done as soon as possible.
If you have lost a considerable amount of
coolant , then you should add cold antifreeze
and cold water only when the engine is cold.
Always use
new engine coolant when refilling . .,.
•
•

M N
~ co
rl I.O
"' rl
"' rl
Brake fluid
Checking brake fluid level
The brake fluid level can be checked with a
quick glance.
N
N
;:;;
" 03
"'
Fi g. 186 Eng ine compartment: Cover on the brake flu ­
id reservoi r
Before you check anything in the engine com­
partment,
a lwa ys read and heed a ll W ARN­
ING S c:> .&.. in Working in the engine compart­
ment on page 212 .
~ Read the brake fluid level from the brake
fluid reservoir
c:> fig. 186, <=> page 214,
fig . 182.
The brake flu id level must be be­
tween the "MIN" and "MAX" markings.
The brake fluid reservoir is located at the rear
partition of the engine compartment on the
left side
<::;> page 214 .
The fluid level may drop slightly after some
time due to the automatic adjustment of the
brake pads . This is not cause for alarm .
If the brake fluid level falls
considerably be­
low the "MIN" mark, the brake warning/indi­
cator light (U.S. models:~, Canadian
models: .) will come on
r:> page 15. Do not
continue to operate the vehicle. The complete b rake system shou ld be thoroughly checked
by an authorized A udi dealer or qualified
workshop and the cause co rrected . If the
b rake fluid level is too low, the brake warn ing/
indicator light w ill illuminate. Contact an au­
thorized Audi dealer
immediately .
@ Tips
The brake f luid reservoir is located under­
neath the cover .
Checking and fillin g 221
Changing brake fluid
Have the brake fluid changed by an experi­
enced technician.
Brake fluid absorbs moisture from the air. If
the water content in the brake fluid is too
high, corrosion in the brake system may result
after a period of time . The boiling point of the
brake flu id will also dec rease considerably and
decrease braking pe rformance.
Therefore, the brake fluid must be changed
every two years. Always use new brake flu id
which conforms to Federal Motor Vehicle
Standard "F MVSS 116 DOT 4".
The brake fluid reservo ir can be d iff icult to
reach, the refore, we recommend that you
have the brake fluid changed by your author­
i zed
Audi d ealer. Your dealer has t he correct
tools, the right brake fl uid and t he know-how
to do this for you .
A WARNING -.
-Brake fluid is poisonous . It must be stor­
ed only in the closed original container
out of the reach of children!
- Brake failure can resu lt from o ld or inap­
propriate brake f luid. Observe these pre­
cautions:
- Use only brake fluid that meets SAE
spe cificat ion
J 1 7 03 and conforms to
Federa l Moto r Ve hicl e Standard 116.
Always check with yo ur authorized Audi
dealer to make sure yo u are using the
correct bra ke fluid. The correct type of
brake f luid is also indicated on the
brake f luid reservoir.
- The brake fluid must be new. Heavy use
of the brakes can cause a vapor lock if
the brake fluid is left in the system too
l ong. This can seriously affect the effi­
c iency of the brakes as well as your
safety. Th is cou ld resu lt in an accident.
(D Note
Brake fluid will damage the paint of your
vehicle .

224 Checking and filling
(D Note
- Do not disconnect the vehicle battery
when the ignition is switched on or when
the engine is running, otherwise, you will
damage e lectronic components i n the
electrical system.
- If your vehicle is going to stand for a
long period of time without being driven,
protect t he battery from "freezing", oth­
e rwise it w ill be damaged and w ill then
have t o be repla ced.
Battery charging
Starting the engine requires a well charged
batt ery.
Fig. 187 Eng ine compartment: Connectors for charger
a nd jumper cables
Always read and heed all WARNINGS below
c::> & and c::> & in Working on the battery on
page 223 .
•Turnoff th e ignit ion and all electrical con­
sumers.
• Make sure the area is well vent ilated when
yo u cha rge the battery .
• Ope n the engi ne hood
i=!.> page 2 12.
• Open the cove r o n the pos it ive pole
e!.>fig. 187.
• Connect the charger connectors according to
t h e instr uctions to the
jump start bolts.
(Bo lts under the cover = "positive", Bolts
with hex head= "negative").
• Only now plug the mains lead for the charg­
i ng equipment into the wall outlet and turn
i t on
c::> .&,. .
• Make sure the charging rate i s not over
30 amps /14.8 Volt .
• When the battery is fully cha rged: Turn the
charging equipment off and remove the
mains lead from the wall out let.
• Now remove the clamps for the charging
equ ipment.
.,. Close the cover on the positive pole .
.,. Close the hood
c::> page 212.
A discha rged battery can freeze at tempera­
tures of only 32 °F (0 °C). Allow a frozen bat­
tery to thaw comp letely before attempting to
charge i t
c::> .&.. However, we recommend not
u sing a thawed batte ry aga in because the ba t­
te ry casing can be c racked due to ic e f orma­
t io n an d can leak ba ttery a cid.
Battery charging (Maximum charging rate
of
30 amps/14.8 Volt)
When ch arg ing at low vo lta ges (e.g. wi th a
trickle charger ), the ba tte ry cables do not
have to be disconnected f irs t. T he bat tery
caps should
not be opened when charg ing a
battery .
It is no t necessa ry to remove the b att ery from
t h e luggage com partmen t.
Fast charging the battery (charging rate
above 14.8 Volts)
F or te chnica l re asons do not u se a batt ery
ch arger that uses voltage greater than
14 .8
Volts to c harge yo ur vehicle's battery.
A WARNING
.------
C harging a battery can be dan gero us.
-A lways follow t he operati ng inst ru ctions
p rovi ded by the battery charger manu ­
facturer when charg ing your battery.
- Never charge a frozen batte ry . I t may ex­
p lode because of gas trap ped in the ice.
A llow a frozen battery to thaw out f irst.
- Do not reuse batteries w hich were fro­
zen. The battery housing may have
cracked and weakened w hen the battery
froze .
- Charge the battery in a we ll ventilated
area. Keep away from o pen flame or elec­
tr ica l spark. Do not s moke. Hyd rogen gas
ge nera ted by t he battery is explos ive .

226 Checking and filling
Clean water should be used when filling up. If
possible, use soft water to prevent scaling on
the washer jets. Always add a glass cleaner
solut ion (with frost protection in the winter) .
Do not mix engine coolant antifreeze or
any other additives to fill up the wind­
shie ld washer reservoir.

lead to a serious or fatal ac­
cident.
- Incorrect tire pressures
and/or underinflation cause increased tire wear and can
affect the handling of the
vehicle .
-Incorrect tire pressures and/or underinflation can
also lead to sudden tire fail­ure, including a blowout
and sudden deflation, caus­ ing loss of vehicle control.
Checking tire pressure
The correct tire pressure for the
tires originally installed on
your vehicle is listed on the tire pressure label located on driv­er 's side 8-pillar.
The recommended tire pres­
sures are on the tire pressure
label and in the table
c:> page 234, Cold tire inflation
pressure.
This means that the
pressure must be checked and
adjusted when the tire has not
been driven for more than a
couple of miles (kilometers) at
low speeds during the previous
three hours. Air in the tires ex­ pands when the tire heats up as
Tires and wheels 239
a result of internal friction as it
flexes in use. The tire pressure is higher when the tire has
warmed up than when it is " ld ,, co .
It is the inflation pressure in a
"cold" tire that counts. There­
fore, you should never let air
out of a warm tire to match
"Cold tire inflation pressure" recommendations
c:> page 234.
The tires would then be under­ inflated and could fail sudden­
ly.
The tire pressure label on your
Audi lists the recommended cold tire inflation pressures at maximum capacity for the new,
original equipment tires that
were on your vehicle at the time it was manufactured. For the
location of the label
c:> page 234, fig. 189.
Most tires lose air naturally
over time. They can also lose
some air if you drive over a pot­ hole or hit a curb while parking.
It is usually not possible to see
whether the radial tires used
today are underinflated just by looking at them.
•
•
'

240 Tires and wheels
Therefore, be sure to check tire and luggage) for the tires on
pressures at least once a month your vehicle as listed on the on
and always before going on a your vehicle and in this manual
long trip. Make sure to take the and the kind of driving you plan
number of people and the to do.
amount of luggage into ac-
Never exceed the maximum in-
count when adjusting tire pres-flation pressure listed on the
sure for a trip -even one that tire sidewall for any reason.
you would not consider to be
Remember that the vehicle
" long ." See
¢ page 242, Tires
manufacturer, not the tire man-and vehicle load limits for more
important information. ufacturer, determines the cor-
rect tire pressure for the tires
Always use an accurate tire on your vehicle.
pressure gauge when checking It is important to check the tire
and adjusting inflation pres-
pressure when the tires are
sures. Check all of the tires and
be sure not to forget the spare cold
.
tire. If the pressure in any tire is -Read the
required tire pres-
too high when the tire is "cold", sure from the tire pressure
la-
let air out of the tire slowly bel.
The tire pressure label is
with the edge of the tire gauge located
on the driver's side B-
and keep checking the pressure pillar. The tire pressure label
until you reach the pressure lists the recommended cold
that is correct for the load (pas- tire inflation
pressures for the
sengers and luggage) and kind vehicle at its maximum capaci-
of driving you plan to do. ty weight and the tires that
If the pressure in any tire is too were on your
vehicle at the
time it was manufactured. For
low, note the difference be-
tween the pressure in the cold recommended
tire pressures
for normal load conditions,
tire and the pressure you need
please see chapter
and add the air that you need to
¢page 234. ...
reach the correct pressure for
the vehicle load (passengers