12 Instrum ent s and indicator lamp s
Fuel level
The display @
c;, page 10, fig. 3 only works
when the ignition is sw itched on . When the
d isplay has reached the reserve mark, the bot
tom LED wi ll turn red and the
tD indicator
light turns on¢
page 23 . The bottom LED
blinks red when the fue l level is very low .
The on -board computer shows the range
based on the fuel leve l
c;, page 2 7, On-board
computer display.
F or the tank capac ity in yo ur vehicle , refer to
the Tec hnical Data ¢
page 280.
CJ) Note
Never d rive until the tank is completely
empty. The irregular supp ly of fuel that re
sults from that can cause the engine to
misfire. Uncombusted f uel will then enter
the exha ust system. This can cause over
heating and damage to the catalytic con
verter .
Coolant temperature indicator
The coolant temperature ind icator @
c::> page 10, fig . 3 only works when the ignition
is switched on . T o prevent engine damage, ob
serve the fo llow ing notes about the tempe ra
ture ranges.
Cold range
If only the LEDs at the bottom of the gauge
turn on, the engine has not reached operat ing
temperature yet . Avoid high engine speeds,
fu ll acce le rat ing and heavy engine loads.
Norm al range
The engine has reached its operating temper
ature once the LEDs up to the center of the
gauge turn on under normal driving condi
tions. The L EDs higher up may turn on if the
engine is under heavy load or the o uts ide tem
perat ure is h igh. This is not a cause for con
cern as long as the. indicator light in the
display does not t urn on. Hot range
If the L
EDs in the upper area of the d isp lay
and the. indicator light in the instrumen t
cluster disp lay t urn on, the coo lant tempe ra
ture is too high
c::> poge 19.
A WARNING
-Always observe the warning in
c;, page 214 before opening the hood
and checking the engine coolant level.
- Never open the eng ine hood if you see or
hear steam, or if you see engine coo lant
dripping from the engine compartment .
You could burn yourself. Let the engi ne
coo l off first until you can no longe r see
or hea r steam or coolant escaping.
([) Note
- Add itiona l headlights and other compo
ne nts in front of the a ir intake impairs
the cooling eff ect of the coolant. This in
creases the risk of the engine over heat
ing dur ing high outs ide temper atures
and heavy eng ine load .
- The front spoiler also he lps to distr ibute
cooling air correct ly wh ile driving.
If the
spoiler is damaged, the coo ling effect
wi ll be impai red and the risk of the en
gine overheating will increase. See an au
thorized Audi dealer o r authorized Aud i
Service Facility for ass istance.
....,
N
r--. > co
rl I.O
"' rl
"' rl
Service interval display
The service interval display detects when your
v e hicle is due for service .
Fig. 6 In str um en t cluste r: serv ice inte rva l d isp lay (ex
a m ple)
Fig. 7 Disp lay in th e MMI panel: se rv ice interval display
(exa mple )
The serv ice interva l display works in two
stages:
- Inspection or oil change reminder : After a
certain distance driven, a message appears
i n t he instr ument cluster d isp lay each time
the ignit ion is switched on or off
r=> fig. 6.
The remaining distance or t ime is d isplayed
briefly.
- Inspect ion or oil change due : If your vehicle
is due for a n insp ection or o il change or
bot h, a message appears br iefly in the in
strument cluster d isplay when switching the
ignition o n or off:
In spection due! or Oil
change due! or Oil change and in spection
due!.
Checking service intervals
You can check the remaining distance or time
until the nex t oil change or next inspection in
the M MI
¢ fig. 7. Se lect t he I MENU ! button >
Instruments and indicator lamps 13
Car > Systems* control button > Service &
control
> Service intervals .
Resetting the display
Your a uth orized Audi dea le r or auth oriz ed
A udi Se rv ice F acility will rese t the service in
te rv al disp lay after pe rfo rmi ng se rvice.
I f you perfo rm an o il change you rself to the
A udi spe cifications, yo u can reset yo u service
in terval disp lay.
T o reset the display, select the
!ME NUI button
> Car > Sy stem s* control button > Service &
control
> Servi ce interval s > Reset oil change
interval.
(D Note
- On ly r eset th e oil chang e indicato r if th e
oil was cha nged.
- Following the se rv ice intervals is critical
t o m ain ta ini ng th e se rv ic e life a nd val ue
o f yo ur v ehicl e, espe cially th e e ngine.
E ven i f the mile age on t he vehicle i s low,
d o no t exceed the time for th e nex t serv
ice.
- Calcu lating t he time to the next oil
c hange is in te rrupt ed whe n the vehicle
battery is dis connected. If t he vehicle is
n ot d riven f or a long period o f time,
check the ma intenance schedule so th at
you ca n follow the maintena nce inter
vals.
Indicator lights
Description
Fig. 8 Instrum en t cluste r: example of a display in
vehicles wit h a mo noc hrome display
@ Ind icator light
16 Instruments and indicator lamps
or
·~
Lt
CD
TPMS
;
or
or
or Hill ho
ld*
Q page 22
Tire pressure monitoring system
,/
Qpage 258
Tire pressure monitoring system
Q page 258
Adaptive dampers*
Qpage25
Engine control (gasoline eng ine)
,/
Q page 22
Exhaust control system ,/
Qpage 23
Engine speed limitation
Qpage 23
Engine oil level (min.)
Qpage 23
~ -SE NSOR
or
or
or
or
or Engine
oil sensor
Qpage23
Engine temperature
Qpage 19
Battery charge level
Qpage20
Tank system
Qpage23
Washer fluid level
Qpage24
Windshield wipers
Qpage24
Steer ing,// s teer ing lock
Qpage 192
Steering lock
Q page21
20 Instruments and indicator lamps
_& WARNING
-Never open the hood if you can see or
hear steam or coolant escaping from the
engine compartment . This increases the
risk of burns. Wait until you no longer
see or hear steam or coolant escaping.
-
-The engine compartment in any vehicle
can be a dangerous area. Stop the engine
and allow it to cool before working in the
engine compartment. Always follow the
information found in
<:;>pag e 214, Work
ing in the engine compartment.
(D Note
Do not continue driving if the. indicator
light turns on - th is increases the risk of
engine damage.
off engine! Oil pressure too low
Stop the engine and do not continue driving.
Check the engine oil level
<:;>page 218.
-If the engine oil level is too low, add engine
o il ¢
page 217. Only continue driving once
the indicator light turns off.
- If the engine oil level is correct and the indi
cator light still turns on, turn the engine
off
and do not continue driving. See an author
ized Audi dealer or author ized Audi Serv ice
Fac ility for assistance.
@ Tips
The oil pressure warning is not an oil level
ind icator. For this reason, check the oil lev
el regularly.
0 Alternator/battery
• Alternator f ault: battery is not being
charged
There is a malfunct ion in the alternator or the
vehicle electrical system.
Drive to an authorized Aud i dealer or author
ized Audi Service Facility immed iately. Be
cause the vehicle battery is draining, turn off all unnecessary electrical equipment such as
the
MMI. See your authorized Audi dea ler or a
qualified repair facility if the battery charge
l evel is too low.
(•] low battery charge: Battery will be
charged while driving
The starting ability may be impaired.
If this message turns off afte r a little while,
the battery has charged enough wh ile driving.
If the message does not turn off, have and au
thorized Audi dea ler or authorized Audi Serv
ice Facility repair the malfunction.
tli1 !I: Safety systems
The II (USA models) Im (Canada models)
indicator light monitors the safety systems.
Safety system
If the II (USA models)/ m (Canada models)
indicator light turns on or blinks, there is a
malfu nction in a safety system.
Drive to an authorized Audi dealer or author
ized Audi Serv ice Facility immediately to have
the malfunction corrected.
_& WARNING
-Have the safety systems inspected imme-
diately. Otherwise, there is a risk that the
systems may not activate during a colli
s ion, wh ich increases the risk of serious in
jury or death.
4f-Front safety belt
The. indicator light stays on until the driv
er's and front passenger's safety belts are
buck led. There is also a warning tone above a
certain speed .
(D Tips
For additional information on safety belts,
refer to¢
page 138.
M N ,....
> co ,...., \!) ..,.,
,...., ..,., ,....,
-Vehicles with a conven ience key
¢ page 79, Automatic start malfunction.
a System indicator light (MIL)
The system indicator light (MIL) is part of the
On Board Diagnostic system (OBD II). The
¢4 symbol turns on when the ign it ion is
switched on and turns off aga in once th e en
g ine is started an d running at a st eady idle
speed. This ind icates that the M IL is funct ion
ing cor rectly .
The indicator light turns on if there is a mal
function in the engine electronics . See an au
thor ized Audi dealer or authorized Audi Se rv
ice Facility to have the malfunction co rrected.
The system indicator light (MIL) may turn on
if the fuel fille r cap is not closed correctly
¢ page 212.
For addit ional i nformation, refer to
¢ page 29.
!?) Engine speed limitation
Appl ies to vehicles: with engine speed limitation
(Ill Max. engine spee d: XXXX rpm
The engine speed is automatically lim ited to
the speed disp layed in the driver information
system. This protects the engine from over heat ing.
The engine speed limitation deactivates once
the eng ine is no longer in the cr it ica l tempera
ture range and you have released the accelera
tor peda l.
If the engine speed limitation was activated by an eng ine control malfunction, the~ indi
cator light also turns on. Make s ure the en
g ine speed does not go above the speed dis
p layed, for examp le when downsh ifting. Drive
to an author ized Audi dealer or author ized
Aud i Service Fac ility immediately to have the
malfunct ion corrected .
'l'.::r., Engine oil level (min.)
II Check oil level
In strum ent s an d indicator lamp s 23
You may cont inue driving for the time be ing.
Check the oil leve l as soon as possib le
¢ page 217.
-If the eng ine o il level is too low, add eng ine
oil ¢page218 .
-If the eng ine o il level is correc t and the indi
cato r light still turns on, drive at low engine
speed to the nearest authorized Audi dealer
or qualified repair facility.
~"" Engine oil sensor
• Oil le vel sensor: system fault!
The sensor to check the engine oi l level has
failed. Drive to an author ized Audi dealer or
authorized Aud i Service Fac ility immediately
to have the malfunction corrected.
(D Note
Refe r to the description in the Owner's
M anual
¢ page 218 and ¢page 218,
Adding engine oil
liD Please refuel
If the indicator light turns fi rst turns on and
th is message appears, the tank conta ins the
follow ing amount of fue l:
- Front whee l drive: approximate ly 1. 8 ga l
lons (7 liters)
-All wheel drive: approximately 2 .2 gallons
(8 . 5 liters)
liD Plea se refuel immediately
If the indicato r light turns on the message ap
pears, the fue l tank is a lmost empty . Refuel
t h e ve hicl e immed iate ly.
liD Fuel tank malfunction! Please contact
Service
If the indicator light turns on and this mes
sage appears, there is a malfunct ion in the
ta nk system .
•
M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Switchin g th e ig nition on /off
"'T o sw itch the ignition on, turn the ignition
key to position
(D .
"'To switch the ignition off, turn the ignition
key to position @.
Starting the engin e
Your vehicle is equipped w ith launch cont ro l.
As soon as you have turned the ign ition key to
position @, the engine will start automatical
l y.
"' Press the brake peda l and move the se lector
lever to the P or N pos it ion.
"'T urn the key briefly to position @. The igni
t ion key automatically r eturns to posit ion
(D . Do not press the accelerator pedal wh en
doing this .
Major electrical equipment switches off tem
porarily when starting the eng ine.
If the engine does not sta rt immedia tely , stop
the starting procedure by turning the ignition key to position @and repeat after 30 sec
onds .
Automatic start m alfunction
If the ~ indicator l ight turns on (gasoline en
g ine) and the message
Engin e start sys te m
m alfu nction. Ple ase contac t Se rvice
appears ,
there is an automatic start ma lfunction.
To start t he eng ine, hold the ignition key in
position @until the engine runs .
Drive to an authorized Aud i dealer or author
ized Audi Service Facility immed iate ly to have
the ma lfunction corrected .
_& WARNING
-Never allow the engine to run in confined
spaces -there is a risk o f asphyxiation.
- Never remove the ign ition key from the
ignition lock whi le the vehicle is moving .
Otherw ise the steering lock wi ll engage
and you will not be able to steer the vehi
cle.
- Please note that the brake booster and
power steering only work when the en-
Dri vin g 77
gine is running. When the engine off, you
must use more force to steer or brake
the vehicle. Because the usual steering
and brak ing capability is not avai lab le,
the risk of accidents or injur ies increases.
- Always take the vehicle key with you
when leaving the vehicle, even for a
short period of time. This applies part ic
ularly when children remain in the veh i
cle. Otherwise the ch ild ren could start
the engine or operate electrical equip
men t such as power w indows.
(D Note
- Avo id h igh engine speed, full throttle,
and heavy eng ine load as long as the en
gine has no t reached operat ing tempera
t u re yet . You could damage the engine.
- T he engine cannot be started by pushi ng
or towing.
(® For the sake of the environment
Do not let the eng ine run w hile pa rked to
warm u p. Begin driv ing immediately . T his
r educes unne cessary emissions.
(D Tips
- If it is d iff icult to turn the key to position
(D , turn the steering wheel back and
forth slightly to release the s teer ing
wheel lock .
- After s tarting a cold engine, there may
be a brief period of inc reased no ise be
cause the oil press ure must first bui ld up
in the hydraulic va lve adj usters . This is
normal and not a cause for concern.
- If the battery is disconnected and recon
nected, you have to hold the ignition key
in posit ion
(D for five seconds for the en
gine to start.
- After sw itching the ignition off, you can
only remove the key when the selector
lever is in the "P" (Park) position. After
that, the selector lever is locked.
•
M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Switchin g th e ig nition on /off
If the> ,:r- u indicator l ight blinks and the mes
sage
Ple ase move s teering wheel appea rs
when switching the ignition on, the steering is locked by th e steering lock. In this case, turn
the steering wheel slight ly to the left/ right.
.. To switch the ignition on or
off, press the
I S TAR T ENG INE S T OPI button. Do not press
the brake pedal whil e doing this .
Starting the engin e
Your vehicle is equipped with launch cont ro l.
The engine starts automa tically when you
press the
I S T AR T ENG INE S T OP I button brief
l y.
.. Press the brake peda l and move the se lector
lever to the P or N pos ition .
.. Press the
I STAR T ENGINE STOP I button
briefly . The eng ine will star t.
Majo r electrical equ ipment switches
off tem
porarily when starting the eng ine .
I f the engine does not start immediately , stop
the starting procedu re by push ing the
I S TAR T ENGINE ST OP ! button again and re
peat after 30 seconds .
Automatic start m alfunction
If the Ila indicator l ight turns on (gasoline en
g ine) when you start the engine, there is an
automatic sta rt malfunction .
To start the eng ine, press and hold the
!STAR T ENGIN E STOP ! button until the eng ine
runs.
Drive to an authorized Aud i dealer or author
i z ed Audi Service Fac ility immed iately to have
the malfunction corrected .
A WARNING
-Never allow the engine to ru n in confined
spaces -there is a r isk of asphyxiation.
- Always take the veh icle key with you
when leaving the vehicle, even for a
short per iod of t ime . This applies partic
ularly when chi ldren remain in the vehi
cle . Otherwise the children could start
Dri vin g 79
the engine or operate electrical equip
ment such as power w indows.
- Please note that the brake booster and
power steering only work when the en
gine is running. When the engine
off, you
must use more force to steer or brake
the vehicle . Because the usual steer ing
and brak ing capability is not avai lable,
the risk of accidents or injur ies increases .
(D Note
-Avo id h igh engine speed, full throttle,
and heavy eng ine load as long as the en
gine has not reached operat ing tempera
ture yet. You could damage the engine .
- The engine cannot be started by pushing
or towing .
@ For the sake of the environment
Do not let the eng ine run wh ile parked to
warm up . Begin dr iv ing immediately . Th is
reduces unnecessary emissions .
(D Tips
-After starting a cold engine, there may
be a brief period of increased no ise be
cause the oil press ure must f irst bu ild up
in the hydraulic va lve ad justers. This is
normal and not a cause for concern.
- If the . indicator light blinks in the in
st rument cluste r before switching the ig
nition
off, the ignit ion wi ll not switch on
again .
qpoge 192
- If you leave your vehi cle wit h the ignition
switched on, the ign it ion w ill switch
off
after a certain amount of time . Make
sure that electrical equipment such as
the exterior lights are switched
off .
T · th · ff using the
button
App lies to vehicles: wit h convenience key
.. Bring the veh icle to a full stop .
.. Move the se lector lever into the P posit ion .
.. Press the
I STA RT E NGINE ST OP ! button
q page 78, fig. 80. ..,.
•
M N ,....
> co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Corrosion
Leaving the vehicle parked for long periods of
time, low mi leage and avoiding heavy braking
can contribute to corrosion on the brake ro
tors and dirty brake pads.
If you usually avoid heavy braking or if there is
corrosion present, occasiona l heavy braking at
high speeds is recommended to clean the
brake rotors and pads~,& .
Brake system malfunction
if you notice that the brake pedal t ravel has
suddenly gotten larger, then a brake circuit
may have failed . Drive to you r authorized Audi
dealer or qualified repair facility immediately
to have the problem corrected. On the way
there, drive with reduced speed and keep in
mind that a long braking distance and in
creased pressure on the brake pedal will be
necessary .
Low brake fluid level
When the brake fluid level is low, ma lfunc
tions in the brake system may occur . The
brake fluid level is electronically monitored.
Brake booster
The brake booster amplifies the pressure you
apply to the brake pedal. It only works when
the eng ine is running.
A WARNING
-You should on ly perform braking maneu
vers to clean the brakes when the road condit ions perm it . Never put others on
the road at risk -never forget the risk of
acc idents!
- On steep slopes, reduce the speed and
select a lower gear or lower selector lev
er posi tion. Drive as little as possible
wh ile pressing the bra ke peda l and avoid
putt ing your left foot on the brake pedal
whi le driving. This could ca use the brakes
to overheat and impair the efficiency of
the brakes.
- Do not let the brakes "grind" by always
keeping yo ur foot on the brake peda l.
Smart Technolog y 191
This can cause the brakes to overheat in-,
crease wear and increase braking dis
tance unnecessar ily.
- Certain weather and operating condi
tions such as driving through water, driv
ing in heavy rain or driving after washing
your veh icle can impa ir the effectiveness
of the brakes. In the winter, ice may
bui ld up on the brake pads, rotors and
drums . Check these components by brak
ing caref ully. App lying the brakes care
fu lly several times dries the brakes and
removes ice build-up .
- The effic iency of the brakes can also be
impaired by driving for long stretches on
roads covered with salt without using the
brakes. You can remove salt deposits
from the brake rotors and pads by care
fully applying the brakes several times.
- If the front spoiler is damaged or you in
stall another spoiler, make sure the front
wheel brakes are ventilated properly.
Otherwise, the brake system could over heat, wh ich reduces their effectiveness .
- Failure of a brake circuit impa irs braking
performance, wh ich increases braking
d istance . Avoid driving the vehicle and
have it towed it to the nearest author
i z ed Audi dealer or authorized Audi Serv
ice Facility.
- Do not let your veh icle roll w ith the en
gine switched off under any circumstan
ces .
- If the brak e booster is not working, you
wi ll have to press much harder on the
brake peda l to compensate for the lack
of the booster.
(D Note
-Never let the brakes "rub" by pressing
the pedal lightly when braking is not
really necessary. This causes the brakes
to overheat and increases braking dis
tance and causes wear.
- Before driving on a long stretch with
steep s lopes, reduce your speed and shift
to the next lower gear This makes use of
the engine brak ing effect and relieves ..,.
•
•
•