2015 AUDI A3 CABRIOLET change wheel

264 What do I do now?
-Always store the vehicle tool kit, the jack
and the replaced tir e in the luggage com­
partment ¢
page 132.
Changing a wheel
When you change o wheel, follow these­
quence described below step-by-step and in
exactly that order .
1. Remove the decorative wheel cover*. For
more details see also¢
page 264, Deco­
rative wheel covers
or ¢ page 265,
Wheels with wheel bolt caps.
2 . Loosen the wheel bolts¢ page 265 .
3. Locate the proper mount ing point for the
jack and align the jack below that point
¢page 266.
4. Raise the car with the jack ¢ page 266.
5. Remove the
wheel with the flat tire and
then install
the spare ¢ page 267.
6. Tighten all wheel bolts lightly.
7 .
Lowe r the vehicle with the jack.
8 . Use the wheel bolt wrench and
firmly
tighten all whee l bolts c::> page 265.
9. Replace the decorative wheel cover*.
A WARNING
Always read and follow all WARNINGS and
information
c::> .&. in Raising the vehicle on
page
266 and c::> page 268.
After changing a wheel
A wheel change is not complete without the
doing the following .
• Always store the vehicle tool kit, the jack*
and the replaced tir e in the luggage com­
partment ~
page 132 .
• Check the tire pressure on the spare wheel
i mmediately after mount ing it.
• As soon as possible, have the
tightening
torques
on a ll wheel bo lts checked with a
torque wrench. The correct tightening tor­
que is 90 ft lb (120 Nm).
• Have the flat tire
replaced as soon as poss i­
ble.
(D Tips
- If you notice that the wheel bolts a re
corroded and difficult to turn while
chang ing a tire, they should be rep laced
before you check the tightening torque.
- Drive at reduced speed until you have the
tightening torques checked.
- After changing a whee l, the tire pressure
in all four tires must be checked/correct­
ed and the tire pressure monitoring indi­
cator must be stored in the MMI
c::>page260.
Decorative wheel covers
Applies to vehicles: wit h decorative whee l covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 183 Chang ing a wheel : Remov ing th e w heel cover
Removing
.,. Insert the hook (provided with the vehicle
tool kit) in the hole in the whee l hub cover .
.,. Pull
off the decorative wheel cover
c::>fig.183.

266 What do I do n ow ?
Raising the vehicle
The vehicle must be lifted with the jack first
before the wheel can be removed .
Fig. 186 Sill panels: mark ings
Fig. 187 Sill : posit ion ing the veh icle jack
., Engage the pa rkin g brak e to prevent your
vehicle from rolling un intentionally.
., Move the
se lect or l ever to po siti on P .
., Find the marking (imprint) on the sill that is
nearest the wheel that wi ll be changed
r::> fig. 186. Behind the marking, there is a
lifting po int on the sill for the vehicle jack.
., Vehicles with a sill : Note the position of the
s ill when pos itioning the vehicle jack
¢ fig . 187 .
., Place the vehicle jack (vehicle tool kit) on a
firm su rface. Use a flat, stab le support if
necessary. On a slippe ry surface such as tile,
you should use a non-slip pad (such as a rub­
ber mat)
c::> A .
., Turn the vehicle jack located under the lift­
ing point on the sill to raise the jack until its
arm @r=>
fig. 187 is located under the des­
ignated plastic mount
c> A, r=>@ .
., Align the jack so that its arm@r=> fig. 187
engages in the designated lifting point in
the door sill and the movable base @ lies
flat on the gro und . T he base @ must be
ver­
tical
under the lift ing po int @ . .,
Wind the jack up fu rther until the f lat tire
comes off the ground
r=> A.
Position t he vehicle jack only under the desig ­
nated lifting points on the si ll
¢fig. 186.
There is exactly one location for each wheel.
The jack must not be positioned at any other
location
r=> ,&. r=>Q).
An un sta ble surf ace under the jack can cause
the vehicle to slip off the jack . Always provide
a firm base for the jack on the ground . If nec­
essary place a sturdy board or similar support
under the jack. On
hard, sl ipp ery su rfaces
(such as tiles) use a rubber mat or similar to
prevent the jack from slipping
c> ,&. .
A WARNING ~
-You or your passengers could be injured
while changing a wheel if you do not fo l­
low these safety preca utio ns:
- Position the vehicle jack on ly at the
designated lifting points and align the
jack. Otherwise, the vehicle jack could
slip and cause an injury if it does not
have sufficient hold on the vehicle .
- A soft or unstable surface under the
jack may cause the vehicle to slip off
the jack . Always provide a firm base for
the jack on the ground. If necessa ry,
use a stu rdy board under the jack.
- On hard, slippery surface (such as t iles)
use a rubber mat or simi lar to prevent
the jack from slipping.
- Only raise your vehicle with the vehicle
jack provided by the fac to ry.
If you use
a vehi cle jack for another vehicle, your
vehicle can slide and cause injury.
- Changes in temperat ure or load can af­
fect the height o f the veh icle .
- Never start the engine when the vehi­ cle is raised, which co uld cause an acc i­
dent.
- Suppo rt the ve hicle securely with ap­
propr iate s tands if work is to be per­
formed underneath the vehicle; other ­
wise, there is a potential risk for in jury . .,.

....,
N
r--. > co
rl I.O
"' rl
"' rl
-To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is secu rely engaged.
- Passengers must not remain in the ve­
h icle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and t raffic.
- M ake sure jack position is correct, ad­
just as necessary and then conti nue to
ra ise the jack .
- Changes i n temperature or load can af­
fect the height of the ve hicl e.
CD Note
Do not lift the vehicle by the sill. Pos ition
the vehicle jack only at the des ignated lift­
ing points o n the sill. Othe rwise, your vehi­
cle will be damaged.
Taking the wheel off/installing the spare
Follow these instructions step-by-step for
changing the wheel.
Fi g. 188 Changing a wheel: using the screwdriver han ­
dle (with th e blade re moved} to turn the bolts
F ig . 189 Changing a wheel: alignment pin inside th e
top hole
What do I d o now ? 267
After you have loosened all wheel bo lts and
raised the vehicle off the grou nd, remove and
replace the wheel as follows:
Removing the wheel
.,. Use the hexag onal socket in the scr ewdriv ­
er handle
to completely remove the top ­
most wheel bolt and set it aside on a
clean
surface c:> fig. 188.
.,. Screw the threaded end of the alignment
pin
from the tool kit hand-tight into the
empty bolt hole
c:> fig. 189.
.,. Then remove the other wheel bolts as de­
scribed above.
.,. Tak e off the whee l leaving the a lignment pin
in the bo lt ho le
c:> (D .
Putting on the compact spare wheel
.,. Lift the spare wheel and carefully s lide it
over the alignment pin to guide it in place
c:>(D .
.,. Use the hexagona l socket in the screwdriver
handle to screw in and tig hten all whee l
bolts
slightly.
.,. Remove the a lignment pin and inse rt and
tighten the rema ining whee l bolt slightly
Like the rest .
.,. Turn the jack hand le counter-clockwise to
lower the vehicle until the jack is fully re­
leased .
.,. Use the wheel bo lt wrench to tighten all
wheel bo lts f irmly
c:> page 265 . Tighten
them
crosswise, from o ne bolt to the (ap­
proxima tely) oppo site one, to keep the
wheel cente red.
CD Note
When remov ing or i nsta lling the whee l,
the r im cou ld hit the b rake roto r and dam­
age the ro tor. Wor k carefu lly and have a
second pe rson help you.
(D Tips
Neve r use the hexagonal socket in the han­
d le of the screwdriver to loosen or tighten
the wheel bo lts .
llll-

268 What do I do no w?
-Pull the reversible blade from the screw ­
driver before you use the hexagonal
socket in the handle to t urn the whee l
bo lts.
- When mounting tires with
unid ire ctional
t re ad design
make s ure the tread pat­
tern is pointed the right way
¢ page 268.
-The wheel bolts should be clean and easy
to turn. Check for d irt and corrosion on
the mat ing su rfaces of both the whee l
and the hub. Remove all dirt from these
surfaces before remount ing the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the right direction.
Using a spare tire with a tread pattern
int ended fo r use in a specific dir ection
When us ing a spare tire w ith a tread pattern
i ntended for use in a specific direction, please
note t he following:
- The direction of rotation is marked by an ar ­
row on the side of the tire .
-If the spare t ire has to be installed in the in­
correct direction, use the spare tire only
temporarily since the t ire will not be able to
achieve its optimum perfo rma nce character­
ist ics with rega rd to aquaplaning, noise and
wea r.
- We recommend that you pay particular at­
tent ion to this fact du ring wet weat her and
that you adjust your speed to match road
condit ions .
- Replace the fla t tire w ith a new one and
have it ins talled on your veh icle as soon as
possible to restore the handling advantages
of a unidirectiona l tire .
Notes on wheel changing
Please read the information ¢ page 248, New
tires and replacing tires and wheels
i f you are
go ing to use a spare t ire which is d ifferent
from the tires on your veh icle . After you change a tire:
-
Ch eck the tire pr essure on th e spar e imm e­
diatel y after in stallation .
- Hav e th e whe el bolt tight ening torque
c h ec ked with a torque wr ench as soon as
po ssible by your author ized Audi de aler or
a qu alified servic e sta tion.
- With ste el and alloy wheel r im s, the wheel
bolt s ar e c orre ctl y tightened at a torque of
9 0 ft lb (120 Nm ).
- If you notice th at the wheel b olt s ar e co r­
rod ed and diffi cult to turn w hile changing
a tire , the y should be repl aced before you
check the t ightening to rque.
- Repl ace the flat tire with a new o ne and
ha ve it in stalled on your vehicle as soon a s
possible. Remount the wheel cov er.
Until then , dri ve with extra care and at re­
duc ed sp eed s.
A WARNING
-
- If you are going to equip your vehicle
with tires or rims which differ from those
which were factory installed, then be sure to read the information
¢ page 248,
New tires and replacing tires and
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool kit
are properly secured in the luggage com­
pa rtment and are not loose in the pas­
senger compartment.
- In an accident or sudden maneuver they
could fly forwa rd, injuring anyone in the
veh icle.
- Always sto re damaged wheel , jack and
too ls se curely in the luggage compart­
men t. Otherwise, in an accident or s ud­
den maneuve r they could f ly forwa rd,
causing injury to passengers in the vehi­
cle.

....,
N
" > co
rl I.O
"' rl
"' rl
No. Equipment Ampere
Door/front passenger's side
F39 doors (for examp le, power
30
windows)
F40 Sockets 20
F41 Reversible front
passenger's
25
side safety belt tensioners
F42 Central locking components,
40
windshield washer system
F43 Headlights, light ing 30
F44 all wheel drive
15
F49 Starte
r, clutch sensor, head-
5
light re lay coil
FS3 Rear window defogger 30
The power seats* are protected v ia
ci rc uit
b reaker s
that automatically sw itch on after a
few seconds after the overload has been re­
duced.
(D Tips
Note that the following table was accurate
at the time of print ing and is subject to
change.
Left engine compartment fuse
assignment
F ig. 193 Engine compartme nt: fuse assignment
No.
Fl
F2
F3
F4
F5
F6
F7
F8
F9
FlO
F ll
F12
Fl3
FlS
F l 6
F l 7
Fl8
F19
F20
F22
F23
F24
F3 1
F32
Fu se s and bulb s 2 71
Equipment Ampere
E5C contro l modu le 40
ESC contro l modu le 40
Engine control module (gas-
15/30
oli ne/d iesel)
Engine cooling, eng ine com-
ponents, auxiliary heater 5/10
coi l relay (1+2), secondary
air injection pump relay
Engine components, tank 7.5/10/
system 15
Brake light sensor 5
Engine components, wa ter 7.5/10/
pumps 15
Oxygen sensor
10/15
Engine compone nts, ex-
haust door, glow time con- 5/10/20
tro l module, SU LEV valve
Fuel injectors, fuel control
15/20
module
Auxiliary heater heating ele- 40
ment 2
Auxilia ry heater heat ing ele-
40
ment 3
Automat ic transmiss ion con-
15/30
t ro l module
Horn 15
Ignit ion coil 5/20
ESC contro l module, engine
7.5
control module
T ermina l 30 (reference volt-
5
age)
Windsh ie ld wipers
30
Horn 10
Termina l 50 diagnosis
5
Starter 30
Auxilia ry heater heat ing ele-
40
ment 1
Vacuum pump 15
L E D head lights 5

M N ,....
> co ,...., \!) ..,.,
,...., ..,., ,....,
Locking/unlock ing
by remote contro l
.............. .. .. 33
with the central locking switch .. .. .. .. 35
with the convenience key . . . . . . . . . . . . . 34
wi th the door lock ........ .... .. .. .. 35
L ong -term memory .............. .. .. 27
L ow beam
I ndicator light . . . . . . . . . . . . . . . . . . . . . 24
Low beams .. .... ............. .. .. .. 49
L ower universal anchorages (Canada) . .. 183
L uggage compartment .. .... .. .. .. .. .. 65
Cargo net .................. .... ... 68
I ncreasing the size . . . . . . . . . . . . . . . . . . 66
L oading .. .. ................. .. .... 65
Reversible mat .............. ... .. .. 69
Socket ..... .. .............. ... .... 64
Storage hooks . . . . . . . . . . . . . . . . . . . . . 68
Stowing luggage ......... .. .. .. .. . 132
Tie-downs . . . . . . . . . . . . . . . . . . . . . . . . . 67
L uggage compartment lid
Centra l locking . . . . . . . . . . . . . . . . . . . . . 38
Emergency release ................. 261
L umbar support . . . . . . . . . . . . . . . . . 60, 61
M
Maintenance ............... ... ... .. 282
Maintenance intervals
with driver information system .. .. .. .. 13
Mirror Digital compass switching on and
off ... 57
dimming ... ................ ... .... 56
Vanity mirror . . . . . . . . . . . . . . . . . . . . . . 53
Mirror compass ............ .... .. .... 57
Mirrors Adjusting the exterior mirrors . .. ... ... 55
Monitoring the Advanced Airbag System 158
Motor stopping (driver messages with mechani-
cal ignition key) .............. .... .. 81
Multifunction steering wheel ..... . ... .. 27
On-board computer ........... ... ... 27
N
Natural leather care/cleaning .. .. .. .. . 207
Navigation system
CD-ROM player . . . . . . . . . . . . . . . . . . . . . 65
Index 293
New tires and wheels
NHTSA 248
Contacting .. .. .. ................. 134
Number of seats . .. ................. 138
Number of vehicle keys ............... 31
0
Occupant protection .. .. ......... .. .. . 95
Occupant seating posi tions ....... .. .. 127
Octane rating ..... ................ . 210
Odometer ........ .. ................ 11
Oil Indicator light . .. ............. .... . 23
also refer to Engine oil . . . . . . . . 217, 218
Oil change interval
with driver information system . . . . . . . . 13
On-Boa rd-D iagnost ic System (OBD)
System indicator light (MIL) ..... .. .. . 29
On-board computer . . . . . . . . . . . . . . . . . . 26
Operation (multifunction steer ing
wheel) .. .. .. .. .... ... .. ..... ..... . 27
On-Board Diagnostic System (OBD)
Data Link Connector (DLC) ......... .. . 30
On Board Diagnostic System (OBD)
E lectronic speed limiter .............. 30
Open ing .... .. .. .. .. .. ........... .. . 31
Fuel filler door ... .. ........... .... 212
Hood ..... .. .. .. .... ............. 215
Luggage compartment lid . . . . . . . . . . . . 38
Windows ......................... 38
Open ing/closing
with the centra l locking sw itch ... .. .. . 35
with the conven ience key ........ .. .. . 34
with the door lock ................ .. 35
Operate your vehicle economically and
minimize pollution ..... ......... .. .. 198
Other equipment (efficiency program) .. . 29
Outside temperature disp lay . . . . . . . . . . . 11
Overview (cockpit) . . . . . . . . . . . . . . . . . . . . 8
p
Paint damage
206
Paint No ..... ..... .. .............. . 279
Parking aid Cleaning sensors/came ra lenses .... .. 205
•
•
•