2015 Acura MDX change time

DISCLoSUreS
California Proposition 65 Warning
WARNING: This product contains or emits chemicals known to the state of California to
cause cancer and birth defects or other reproductive harm.
California Perchlorate Contamination Prevention ActThe airbags, seat belt tensioners, and CR-type batteries in this vehicle may contain
perchlorate materials — special handling may apply. See www.dtsc.ca.gov/
hazardouswaste/perchlorate/ for more information.
Devices That emit radio Waves
The following products and systems on your vehicle emit radio waves when in operation:
•  AcuraLink®
•  Audio system
•  Blind Spot Information (BSI) system
•  Bluetooth® Audio
•  Bluetooth® HandsFreeLink®
•  Collision Mitigation Braking
System
TM (CMBSTM) • 
HomeLink® Universal Transceiver
•  Immobilizer system
•  Remote transmitter
•  Keyless Access System
•  Tire Pressure Monitoring System
Each of the above complies with the appropriate requirements or the required standards
of FCC (Federal Communications Commission) and Industry Canada, described below:
As required by  the FCC:
This  device complies  with Part 15 of the FCC rules.  Operation is subject  to the following 
two conditions:  (1) This  device may not cause harmful interference,  and (2)  this device 
must  accept  any interference received,  including interference that may cause undesired 
operation.
Changes  or modifications not expressly  approved by the party responsible for compliance 
could  void the user’s  authority to operate  the equipment.
As required by Industry  Canada:
This  device complies  with Industry Canada Standard RSS-Gen/210/310.  Operation is subject 
to  the following  two conditions:  (1) this  device may not cause interference,  and (2)  this 
device must  accept any interference,  including interference  that may cause undesired 
operation  of the  device.  
event Data r ecorders
This vehicle is equipped with an event data recorder (eDr). The main purpose of
an EDR is to record, in certain crash or near crash-like situations, such as an air bag
deployment or hitting a road obstacle, data that will assist in understanding how a
vehicle’s systems performed. The eDr is designed to record data related to vehicle
dynamics and safety systems for a short period of time, typically 30 seconds or less.
The eDr in this vehicle is designed to record such data as:
•  How various systems in your vehicle were operating;
•  Whether or not the driver and passenger safety belts were buckled/fastened;
•  How far (if at all) the driver was depressing the accelerator and/or brake pedal; and,
•  How fast the vehicle was traveling.
These data can help provide a better understanding of the circumstances in which crashes
and injuries occur. NOTE: EDR data are recorded by your vehicle only if a non-trivial crash
situation occurs; no data are recorded by the EDR under normal driving conditions and
no personal data (e.g., name, gender, age, and crash location) are recorded. However,
other parties, such as law enforcement, could combine the EDR data with the type of
personally identifying data routinely acquired during a crash investigation.
To read data recorded by an EDR, special equipment is required, and access to the vehicle
or the EDR is needed. In addition to the vehicle manufacturer, other parties such as law
enforcement that have the special equipment can read the information if they have
access to the vehicle or the EDR.
The data belong to the vehicle owner and may not be accessed by anyone else except as
legally required or with the permission of the vehicle owner.
Service Diagnostic r ecorders
This vehicle is equipped with service-related devices that record information about
powertrain performance. The data can be used to verify emissions law requirements and/
or help technicians diagnose and solve service problems. It may also be combined with
data from other sources for research purposes, but it remains confidential.

4 || 5
SAFeTy
SAFeTy
Carbon monoxide Gas
The engine exhaust from this vehicle contains carbon monoxide, a colorless, odorless, and
highly toxic gas. As long as you properly maintain your vehicle and follow the instructions
set forth below, you will not accumulate dangerous levels of carbon monoxide gas in the
vehicle interior.
Have the exhaust system inspected for leaks whenever:
•  The exhaust system is making an unusual noise.
•  The exhaust system may have been damaged.
•  The vehicle is raised for an oil change.
When you operate a vehicle with the tailgate open, airflow can pull exhaust gas into the
interior and create a hazardous condition. If you must drive with the tailgate open, open
all the windows and set the climate control system as shown below.
1. Select the fresh air mode.
2. Select the (
) mode.
3. Set the fan speed to high.
4. Set the temperature control to a comfortable setting.
Adjust the climate control system in the same manner if you sit in your parked vehicle
with the engine running. Improperly operating this vehicle on or off pavement can cause a crash or
rollover in which you and your passengers can be seriously injured or killed.
• Follow all instructions and guidelines in 
this guide.
• Keep  your speed low, and  don’t drive faster  than conditions permit.
WArNING
Safety messages
When you see the following messages throughout this guide, pay close attention.
You WILL be KILLED or SERIOUSLY HURT if you don’t
follow instructions.
You CAN be KILLED or SERIOUSLY HURT if you don’t
follow instructions.
You CAN be HURT if you don’t follow instructions.
This information is intended to help you avoid damage to your
vehicle, other property, or the environment.
WArNING
CAUTIoN
NoTICe
DANGer
An enclosed area such as a garage can quickly fill up with carbon monoxide gas. Do not
run the engine with the garage door closed. Even when the garage door is open, drive out
of the garage immediately after starting the engine. Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and
even kill you.
Avoid any enclosed areas or activities that expose you to carbon monoxide.
WArNING
Seat Belts
A seat belt is your best protection in all types of collisions. Airbags are designed to
supplement seat belts, not replace them. So even though your vehicle is equipped with
airbags, make sure you and your passengers always wear your seat belts and wear them
properly.
Lap/Shoulder Seat Belts
All seven seating positions are equipped with lap/shoulder seat belts with emergency
locking retractors. In normal driving, the retractor lets you move freely while keeping
some tension on the belt. During a collision or sudden stop, the retractor locks to restrain
your body. The front passenger’s, second-row, and third-row seat belts also have a
lockable retractor for use with child seats.
The front seats are equipped with automatic seat belt tensioners to enhance safety. The
tensioners automatically tighten the front seat belts during a moderate-to-severe front
collision, sometimes even if the collision is not severe enough to inflate the front airbags
or the driver’s knee airbag.
Proper Use of Seat BeltsFollow these guidelines for proper use:
•  All occupants should sit upright, well back in the seat, and remain in that position for
the duration of the trip. Slouching and leaning reduces the effectiveness of the belt and
can increase the chance of serious injury in a crash.
•  Never place the shoulder part of a lap/shoulder seat belt under your arm or behind your
back. This could cause very serious injuries in a crash.
•  Two people should never use the same seat belt. If they do, they could be very seriously
injured in a crash.
•  Do not put any accessories on the seat belts. Devices intended to improve comfort
or reposition the shoulder part of a seat belt can reduce the protective capability and
increase the chance of serious injury in a crash.
•  No one should sit in a seat with an inoperative seat belt or one that does not appear to
be working correctly. Using a seat belt that is not working properly may not protect the
occupant in a crash. Have a dealer check the belt as soon as possible.

26 || 27
INSTrUmeNT P
ANeL
INSTrUmeNT P ANeL
on/off Indicators
These indicators remind you when an item is on or off.
VSA off
CRUISE MAIN on
CRUISE CONTROL on
Turn signals/hazards on
High beams on
Exterior lights on CMBS
TM* off
BSI* off
ACC* on
LKAS* on
FCW* off
CRUISE MAINCRUISE
CONTROL
CRUISE MAINCRUISE
CONTROL
multi-Information Display
Consists of several displays that provide you with useful information.
right selector wheel:
Scroll to change main
displays.
main display
Lower display TrIP button: Press to
change lower displays.
Main display
Vehicle Settings Instant/average
fuel economy
Tire pressure for each tire Range
Engine oil life
main Displays
Outside temperature Odometer Outside temperature
Trip A Outside temperature
Trip B
Lower Displays
Elapsed time
Compass/
directions*Average speed
SH-AWD*/IDS
*if equipped *if equipped

34 || 35

veHICLe CoNTroLS
veHICLe CoNTroLS
Interior and exterior Lights
Operate interior and exterior lights when the vehicle is on or off.
exterior Lights
Rotate the switch on the headlight lever to operate the exterior lights. Push the lever
forward to turn on the high beams. Return the lever to its original position for low beams.
OFF All exterior lights are off.
AUTO Turn on the automatic lighting
feature. Headlights turn on or
off depending on ambient
brightness when the vehicle is on.
Headlights automatically come
on after the wipers are engaged for a
certain time.
Turn on exterior lights except headlights.
Turn on all exterior lights including headlights.
Brightness Control
Adjust instrument panel brightness when the vehicle is on.
To brighten: Press the + button.
To dim: Press the - button.
A beep sounds when the brightness reaches minimum or
maximum.
Headlight Washers* Turn the headlights on. Press the headlight washer button to operate the washers.
The headlight washers also operate when you first turn
on the windshield wipers.
Headlight
washer
button
High
beams Low
beams
Flash high
beams
Press the map light
button to turn lights on
or off when the front
light switch is in the
door-activated position.
Interior Lights Change the interior light settings using the switches on the ceiling.
on position: The light
comes on when the
tailgate is open and
goes off when it is
closed.
off position: The light
stays off.
Cargo area lights
Located on the inside of the tailgate door.
on position: Interior
lights remain on.
Door-activated
position: Interior lights
come on when any of
the doors are opened,
the driver’s door
is unlocked, or the
vehicle is turned off.
off position: Interior
lights remain off.Door-activated position
On
Off
Second- and third-row lights
On Off
Front lights
BrightDim
*if equipped (Canadian models)

36 || 37

veHICLe CoNTroLS
veHICLe CoNTroLS
one-Touch Turn Signal
Use this quick and convenient method to signal a lane change.
Lightly push the turn signal lever up or down for a three-blink
sequence.
For a continuous signal, push the lever up or down until it
locks into place.
Wiper operation
The windshield wipers and washers can be used when the vehicle is on.
Front Wipers
Move the wiper lever up or down to the desired position.
Headlight-Wiper IntegrationWhen the headlights are in the AUTO position, they
automatically turn on when the front wipers operate
several times within a certain interval. The headlights
turn off shortly after the wipers are turned off, or if
there is enough ambient light.
Intermittent Wipers*When you move the lever to the INT position, the
wipers operate based on the delay adjustment.
Adjust the wiper delay using the intermittent time adjustment ring.
Right
Left
*if equipped
Automatic rain-Sensing Wipers*
When you move the lever to the AUTO position while driving in rainy weather, the wipers
operate based on the amount of detected rainfall.
Adjust the rainfall sensor sensitivity using the adjustment ring.
r ear Wiper
Rotate the end of the wiper lever to operate the rear
wiper.
When you shift to Reverse (R) and the front wipers are
activated, the rear wiper activates even if the switch is
off.
Mist
Off
Intermittent* (or automatic*)
Low speed
High speed Pull for
washer.
Long delay
Short delay
Lower sensitivity
Higher sensitivity
Intermittent time
adjustment ring
Adjustment ring
Do not use the wipers when the windshield is dry. The windshield will get scratched, or the
rubber blades will get damaged.
In cold weather, the blades may freeze to the windshield, becoming stuck. Operating the
wipers in this condition may damage the wipers. Use the defroster to warm the windshield,
or manually clear the windshield of ice and snow before turning on the wipers.
No TICe
oFF
INT: Intermittent
oN: Continuous wipe
Washer
Washer
Always ensure the wiper lever is in the OFF position before entering a car wash to
prevent severe damage to the windshield wiper system.
NoTICe

50 || 51
AUDIo AND CoNNeCTIvITy
veHICLe CoNTroLS
*if equipped
Customized Features
You can easily customize many features of your vehicle. The customized settings are
recalled every time you unlock the driver’s door with the remote (Driver 1 or Driver 2).
Settings are unique to each remote.
How to Change a Setting
The vehicle must be in Park (P) to select Vehicle Settings. Use the interface dial to make
and enter selections.
1. Press SETTINGS.
2. Select an option (System, Vehicle, Camera, Audio, Phone, Info, or Navi*).
3. Select a setting option, and make your preferred changes.
4. Press BACK to exit out of the menus.
Setting the Clock
On vehicles without navigation, use the interface dial to adjust the time in the clock
display. On vehicles with navigation, the time is automatically set using GPS signals.
1. Press SETTINGS.
2. Select System Settings.
3. Select Clock Adjustment.
4. Rotate the interface dial to change the hour value. Press the interface dial to select
minutes, and rotate to change the value. Press the interface dial to exit the screen.
5. Press BACK to exit out of the menus.
Settings screen
BACK
button
Interface
dial SeTTINGS
button
Basic
Audio operation
Connect audio devices and operate buttons and displays for the audio system.
USB Port
Connect a USB flash drive or other audio device, such as an iPod® or iPhone®.
1. Slide back the center console cover. Open the USB
port cover.
2. Install the flash drive or iPod cable to the USB port.
Auxiliary Input Jack
Connect standard audio devices with a 1/8-inch (3.5 mm) stereo miniplug.
1. Slide back the center console cover. Open the AUX
cover.
2. Connect the device to the input jack.
3. Use the device to control the audio.
iPod  and iPhone  are trademarks  of Apple,  Inc.
State  or local laws may prohibit  the operation  of handheld electronic  devices while operating  a vehicle.
AUDIo AND CoNNeCTIvITy
Learn how to operate the vehicle’s audio system.
Accessory Power Socket
Located in the center console, center pocket, and rear
cargo area. Open the socket cover to use power when
the vehicle is on.
Do not insert an automotive type cigarette lighter element. This can overheat the
power socket.
No TICe

76 || 77
NA
vIGATIoN
NA vIGATIoN
Learn how to enter a destination and operate the navigation system.
Basic Navigation operation
A real-time navigation system uses GPS and a map database to show your current location
and help guide you to a desired destination. You can operate the system using voice
commands or the system controls.
To reduce the potential for driver distraction, certain manual functions may be
inoperable or grayed out while the vehicle is moving. voice commands are always
available.
Steering Wheel Controls
Use the steering wheel controls to give voice commands.
Hang-Up/Back button: Press to cancel a command or
operation.
Talk button: Press to give navigation commands.
v oice Command Tips
•  When using the Talk button, wait for a beep before saying a command.
•  To bypass the system prompts, simply press the Talk button again to say your
command.
•  When the Talk button is pressed, all available voice commands are highlighted in
yellow.
•  Speak in a clear, natural voice.
•  Reduce all background noise.
•  Adjust the dashboard and side vents away from the microphone in the ceiling.
•  Close the windows and moonroof.
Using the navigation system while driving can take your attention away from
the road, causing a crash in which you could be seriously injured or killed.
Only operate system controls when the conditions permit you to safely do so.
NA vIGATIoN*
WArNING
*if equipped
Back
button
Talk
button
Navigation Display and Controls Use the controls to enter information and make selections.
REAR
REAR
AUDIO
FRON
T
AUDIO
NAVFFFFAAAAAAAAAREARAUDIOFAAFRON
TAUDIOAA
REAR
NAVNAVFRONT
AUDIOREAR
AU DIO
NA v button:
Display the map
screen or directions
when en route. INFo button:
Select items such
as calendar, traffic
incidents, and
AcuraLink messages.
BACK button:
Return to the
previous display. meNU button:
Enter destination
information.
button: Change
screen brightness. Use
the interface dial to
make adjustments. Interface dial (from the map
screen): Rotate to zoom in or
out of the map. Press to display
the map menu. Rotate and press
to make and enter selections.
GPS
signal
strength Traffic
incident
icon*
Traffic
status* Traffic
flow*
Current
map scale
Current
vehicle
position
map
orientation
Current
street Landmark
icon
*subscription feature
SeTTINGS button:
Choose Navi Settings.

96 || 97
DrIvING
DrIvING
Cruise Control
Maintain a constant vehicle speed without having to keep your foot on the accelerator
pedal. Use cruise control on freeways or open roads where you can travel at a constant
speed with little acceleration or deceleration.
Improper use of the cruise control can lead to a crash.
Use cruise control only when traveling on open highways in good weather.
Activating and Setting the vehicle Speed
1. Press CRUISE. The CRUISE MAIN indicator appears.
2. Accelerate to the desired speed (above 25 mph/40 km/h).
Press RES/+ and take your foot off the pedal to set the
speed. The CRUISE CONTROL indicator appears.
Adjusting the v ehicle Speed
Press RES/+ to increase or SET/- to decrease.
Each time you press the button, the vehicle speed is increased
or decreased by about 1 mph (1 km/h). If you keep the button
pressed, the vehicle speed increases or decreases until you
release it.
Canceling Cruise Control Press CANCEL or the brake pedal. The CRUISE CONTROL
indicator goes off.
After cruise control has been canceled, you can still resume the
prior set speed by pressing RES/+ while driving at a speed of at
least 25 mph (40 km/h).
Press CRUISE to turn the system off.
CRUISE button
RES/+ button
SET/- button
CANCEL button
WArNING
Adaptive Cruise Control (ACC) with Low Speed Follow*
Helps maintain a constant vehicle speed and a set following distance behind a vehicle
detected ahead of yours. When the vehicle ahead changes speed, ACC senses the change
and accelerates or decelerates to maintain a set interval.
MAIN button
RES/+ button
SET/- button
CANCEL button
Distance button
Activating and Setting the vehicle Speed
1. Press MAIN. The ACC indicator appears.
2. Accelerate to the desired speed.
  Above 25 mph/40 km/h: Press SET/- and take
your foot off the pedal to set the speed.
  Below 25 mph/40 km/h (Low Speed Follow):
Press SET/- to set the speed below 25 mph/40
km/h when there is a vehicle ahead of you. If
there is no vehicle ahead, ACC will not engage.
Adjusting the v ehicle Speed
Press RES/+ to increase or SET/- to decrease.
Each time you press the switch up or down, the vehicle speed
is increased or decreased by about
1 mph (1 km/h). If you keep the switch pressed up or down,
the vehicle speed increases or decreases by
5 mph (8 km/h) until you release it.
Adjusting the Following Distance Press the Distance button to change the following distance.
Each time you press the button, the following distance cycles
through short, middle, long, and extra long.
Switching to Standard Cruise ControlPress and hold the Distance button.
*if equipped