2015.5 VAUXHALL MERIVA lock

Seats, restraints37
Seat positioning
Pull handle, slide seat, release
handle. Try to move the seat back and forth to ensure that the seat is locked
in place.
Seat backrests
Pull lever, adjust inclination and
release lever. Allow the backrest to
engage audibly.
Seat height
Lever pumping motion
up=seat higherdown=seat lower

Seats, restraints43
Insert the hooks of the adapter into
the recesses of the seatback and
push the adapter forwards.
Lock the adapter by turning the
ignition key clockwise in the lock. The adapter is locked properly when the
green mark is visible.
Mount the armrest on the adapter.
Armrest 3 39.
Attaching the armrest to the
adapter
Press the front button and insert the
front guide pins into the guide rails. Move the armrest until it engages
audibly. Release the button.
Lower the armrest at the rear. Pull the rear handle firmly and insert the rear
guide pins into the guide rails.
Release the handle.
Notice
Install the armrest in the direction
shown in the illustration. Otherwise
the armrest may not engage
properly.
Removing the armrest Pull the rear handle firmly and raise
the armrest at the rear. Press the front
button and remove the armrest.

44Seats, restraints
Removing the adapter
Unlock the adapter by turning the
ignition key anticlockwise in the lock.
The adapter is unlocked when the red mark is visible.
Push the adapter rearward and
remove.Seat belts
The seat belts are locked during
heavy acceleration or deceleration of
the vehicle holding the occupants in
the sitting position. Therefore the risk
of injury is considerably reduced.
9 Warning
Fasten seat belt before each trip.
In the event of an accident, people
not wearing seat belts endanger their fellow occupants and
themselves.
Seat belts are designed to be used by only one person at a time. Child
restraint system 3 54.
Periodically check all parts of the belt
system for damage, pollution and
proper functionality.
Have damaged components
replaced. After an accident, have the
belts and triggered belt pretensioners replaced by a workshop.
Notice
Make sure that the belts are not
damaged by shoes or sharp-edged
objects or are trapped. Prevent dirt
from getting into the belt retractors.
Seat belt reminder X 3 94.
Belt force limiters Stress on the body is reduced by the
gradual release of the belt during a
collision.
Belt pretensioners In the event of a head-on or rear-end
collision of a certain severity, the front
seat belts are tightened.

Seats, restraints47
Click bottom latch plate into right-
hand buckle ( 1) at centre seat.
Remove top latch plate from retainer,
guide over shoulder and lap area with belt (do not twist) and click into left-
hand buckle ( 2) at centre seat.
To remove the seat belt, first press
the button on the left-hand buckle ( 2)
and remove top latch plate. Then
press the button on the right-hand
buckle ( 1) and remove bottom latch
plate. The seat belt retracts
automatically.Push the top latch plate into the
retainer. Fold over locked together latch plates against the seat belt.
Insert in the seat belt holder in the roof
with the lower latch plate pointing
forward.
Using the seat belt while
pregnant9 Warning
The lap belt must be positioned as
low as possible across the pelvis
to prevent pressure on the
abdomen.

Storage61StorageStorage compartments................61
Load compartment .......................73
Roof rack system .........................79
Loading information .....................80Storage compartments9Warning
Do not store heavy or sharp
objects in the storage
compartments. Otherwise, the
storage compartment lid could
open and vehicle occupants could be injured by objects being thrown
around in the event of hard
braking, a sudden change in
direction or an accident.
Glovebox
The glovebox features a pen holder,
a coin holder and an adapter for the
locking wheel bolts.
Inside the glovebox there is a
compartment for the Owner's Manual. Pull the lug to open the compartment.
The glovebox should be closed whilst driving.
Cupholders
A cupholder is located in the centre
console.

66Storage
Push the clamping lever down and
push the lamp support into the
retainer until it engages.
Perform this procedure for both tail
lamps.
Check the cable and lamp position to
make sure these are correctly
installed and are securely located.
Lock the rear carrier system
Swivel the right clamping lever ( 1)
first, followed by the left clamping
lever ( 2), until a resistance is
noticeable.
The rear carrier system is locked
when the clamping levers are
swivelled by approx. 50°. Otherwise
safe functionality is not guaranteed.
Notice
Close the tailgate.

72Storage
Insert the strap retainer and pull
tightly downwards as far as possible.
Press release lever and slide in wheel recesses all the way as far as they will
go.
Disengage the locking lever on the
diagonal support and fold both pedal crank recesses down.
9 Warning
Risk of pinching.
Remove number plate and fold down
the number plate holder.
Swivel first the left clamping lever ( 1),
followed by the right clamping lever
( 2 ), until they stop.

Storage73
Push the clamping lever down and
pull both lamp supports out of the
recesses.
Fold in the lamp supports on the
backs of the tail lamps.
First place the front tail lamp ( 1), then
the rear tail lamp ( 2) in the recesses
and push down as far as possible. Push cables all the way into all guides
in order to prevent damage.
Open the tailgate.
Push the release lever up and hold.
Lift the system slightly and push it into the bumper until it engages.
Release lever must return to original
position.
9 Warning
If the system cannot be correctly
engaged, please seek the
assistance of a workshop.
Load compartment
Folding down rear seat backrests The rear seat backrest is divided into
three parts. All parts can be folded
down and lowered individually to
increase the size of the load
compartment.9 Warning
Do not stow objects under or
behind the seats. The objects
might be damaged and prevent
the guide rails from locking
properly.
A completely flat load bay is created if the rear seat backrests are folded
down.