2015.5 Citroen BERLINGO MULTISPACE RHD sensor

43
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
Instruments and controls
Berlingo-2-VP_en_Chap03_Pret-a-partir_ed02-2015
UNDER-INFLATION DETECTION WITH REINITIALISATION
System which automatically checks the pressures  of   the   tyres   while   driving.
The
  system   monitors   the   pressures  
in the four tyres, once the vehicle is
moving.
It

  compares   the   information   given   by  
the four wheel speed sensors with
reference values, which must be
reinitialised every time the tyre
pressures are adjusted or a wheel
changed

.
The
  system   triggers   an   alert   as   soon  
as

  it   detects   a   drop   in   the   inflation  
pressure

  of   one   or   more   tyres. The   under-inflation   detection  system
  does   not   replace   the   need  
for vigilance on the part of the
driver

.
This
  system   does   not   avoid   the   need   to  
check

  the   tyre   pressures   (including   the  
spare

  wheel)   every   month   as   well   as  
before

  a   long   journey.
Driving
  with   under-inflated   tyres  
impairs

  road   holding,   extends   braking  
distances

  and   causes   premature  
tyre wear

, particularly under arduous
condition (high loading, high speed,
long
  journey).
Driving
  with   under-inflated   tyres  
increases

  fuel   consumption.The
  inflation   pressures   defined   for  your vehicle can be found on the
tyre
  pressure   label.
For
  more   information   on   the  
identification

  markings,   refer   to   the  
corresponding

  section.
Tyre
  pressures   should   be   checked  
when the tyres are "cold" (vehicle
stopped

  for   1   hour   or   after   a   journey   of  
less

  than   6   miles   (10   km)   at   moderate  
speeds).
Otherwise

  (when   hot),   add   0.3   bar   to  
the

  pressures   shown   on   the   label.
REadY To Go
3

 59
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
LED DAYTIME RUNNING LAMPS
Rear foglamps (amber, 
2nd rotation of the ring
forwards).
Front
  foglamps   (green,  
1st

rotation of the ring
forwards). Rotate this ring forwards
to switch on and
rearwards   to   switch   off.
Their   state   is   confirmed   by  
the

  warning   lamps   in   the  
instrument

  panel. Do   not   forget   to   switch   them   off  
when

  they   are   no   longer   needed.
Operation   of   the   automatic   illumination  
of

  headlamps   switches   off   the   rear  
foglamps,

  but   the   front   foglamps  
remain

  on.
To switch off the front and
rear   foglamps,   turn   the  
ring rearwards twice in
succession.
Automatic illumination of headlamps
In foggy weather or in snow,
the  sunshine   sensor   may   detect  
sufficient

  light.  
As
  a   consequence,  
the

 
lighting   will   not   come   on  
automatically

.
If
  necessary,   you   must   switch  
on

  the   dipped   beam   headlamps  
manually

.
d

o not cover the sunshine sensor
located on the windscreen, behind
the
 
mirror.   It   is   used   for   the   automatic  
illu

mination   of   headlamps   and   for   the  
automatic

  rain   sensitive   wipers.
Activation
Turn the ring to the AUTO
  position.  
The activation of this function is
accompanied

  by   a   message   in   the  
screen.
Deactivation
T

urn
  the   ring   forwards   or   rearwards.  
The deactivation of this function is
accompanied

  by   a   message   in   the  
screen.
The

 
function   is   deactivated   temporarily  
when

  you   use   the   manual   lighting  
control

  stalk. The
  sidelamps  
and

  dipped   beam  
headlamps

  switch  
on

  automatically   if  
the light is poor

, or
during operation of the windscreen
wipers.  
They
  switch   off   as   soon   as   the  
light

  becomes   bright   enough   or   the  
windscreen

  wipers   stop.
This
  function   is   not   compatible   with   the  
daytime

  running   lamps.
o

n starting the vehicle, in daylight the
LED
 
daytime
 
running
 
lamps
 
come
 
on
 
automatically

.
If
 
the
 
sidelamps
 
and
 
headlamps
 
are
 
switched

 
on
 
manually
 
or
 
automatically,
 
the

 
daytime
 
running
 
lamps
 
go
 
off.
Programming
For countries where exterior lighting by
day   is   not   a   legal   requirement,   you   can  
activate or deactivate the function via
the

  configuration   menu.
If the user does not operate any
equipment
 
for
 
30
 
minutes,
 
the
 
Economy

 
mode
 
engages
 
to
 
avoid
 
discharging

 
the
 
battery.
 
Electrical
 
functions are put on standby and the
battery

 
warning
 
lamp
 
flashes.
Sidelamp
 
operation
 
is
 
not
 
affected
 
by
 
Economy

 
mode.
In clear weather or in rain, both day
and  night,   rear   foglamps   dazzle   and  
their

  use   is   prohibited.
Refer to chapter 8, "Battery
section".
Front and rear foglamps
They
 
operate
 
with
 
the
 
sidelamps
 
and
 
dipped

 
beam
 
headlamps.
Steering mounted controls
EASE OF USE and COMFORT
4

60
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
If the sunshine sensor
does not function correctly,
the  lighting   comes   on  
accompanied

  by   the   service  
warning

  lamp,   an   audible  
signal

 
and   a   message   in   the   screen.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Guide-me-home lighting
Keeping the dipped beam headlamps on   temporarily   with   the   ignition   off,  
makes

  the   driver's   exit   easier   when   the  
light

  is   poor.
HEADLAMP BEAM
The beam setting must be adjusted to suit
  the   load   in   the   vehicle.
0 -
  No   load.
1 -
  Partial   load.
2 -
 
A
verage   load.
3 -
  Maximum   authorised   load.
Manual operation
-
 With
 
the
 
ignition
 
off,
 
"flash"
 
the
 headlamps
 
within
 
one
 
minute
 
after
 
switching

 
off
 
the
 
ignition.
The
 
guide-me-home
 
lighting
 
switches
 
of

f
 
automatically
 
after
 
a
 
set
 
time.
Automatic operation
Refer to chapter 10, "Screen
menu
 
map"
 
section. Initial setting is position 0.
a

ctivate the function via the
vehicle
 
configuration
 
menu. Programming
The
 
system
 
is
 
activated
 
or
 
deactivated
 
in

 
the
 
vehicle
 
configuration
 
menu.
The
 
system
 
is
 
activated
 
by
 
default.
Switching off
The
 
system
 
does
 
not
 
operate:
-

below a certain angle of rotation of
the steering wheel,
-

 
above

 
25
 
mph
 
(40
 
km/h),
-
 
when

 
reverse
 
gear
 
is
 
engaged.
Switching on
This
 
function
 
starts:
-

when the corresponding direction
indicator is switched on,
or
-

 
from

 
a
 
certain
 
angle
 
of
 
rotation
 
of
 
the

 
steering
 
wheel.
With
 
dipped
 
or
 
main
 
beam
 
headlamps,
 
this

 
function
 
makes
 
use
 
of
 
the
 
beam
 
from

 
a
 
front
 
foglamp
 
to
 
illuminate
 
the
 
inside of a bend, when the vehicle
speed

 
is
 
below
 
25
 
mph
 
(approximately
 
40

 
km/h)
 
(urban
 
driving,
 
winding
 
road,
 
intersections,

 
parking
 
manoeuvres...).
Cornering lighting
Travelling abroad
If using your vehicle in a country
that drives on the other side of the
road,
  the   headlamps   must   be   adjusted  
to

 
avoid   dazzling   on-coming   drivers.
Contact a CITR
o Ë n dealer or a
qualified
  workshop.
Steering mounted controls

 61
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
2 Fast  wipe   (heavy   rain).
1  
Normal
  wipe   (moderate   rain).
l
 
Intermittent
  wipe.
0
 
Of
f.
â

Single wipe
 (press

  downwards).
In the Intermittent
  position,   the   wiping  
speed is in proportion to the vehicle
speed.
WIPERS
Manual wipingWhenever the ignition has been
switched  off   for   more   than   one   minute,  
with

  the   windscreen   wiper   stalk   in  
position

  2,   1   or   I,   the   stalk   must   be  
reactivated.
-

 
Move
  the   stalk   to   any   position.
-
 
Return
  it   to   the   desired   position.
d

o not cover the rain sensor,
located in the centre of the
windscreen,
  behind   the   mirror.Activation
Press
  the   control   downwards.  
a ctivation of the function is
accompanied   by   a   message   in   the  
screen.
Deactivation
Place

  the   windscreen   wipers   stalk   in  
position

I, 1 or 2.d
eactivation of the function is
accompanied   by   a   message   in   the  
screen.
In

  the   event   of   malfunction   of   the  
automatic

  windscreen   wipers,   the  
windscreen wipers will operate in
intermittent

  mode.
Contact a CITR
o Ë n dealer or a
qualified
  workshop   to   have   the   system  
checked. In the
AUTO position, the windscreen
wipers   operate   automatically   and  
adapt their speed to the intensity of the
rainfall.
When not in

AUTO   mode,   for   the  
other

  positions,   refer   to   the   manual  
windscreen

  wipers   section.
The   automatic   rain   sensitive  
windscreen

  wipers   function   must  
be

  reactivated   by   pressing   the   stalk  
downwards, if the ignition has been
switched

  off   for   more   than   one   minute.
When   using   an   automatic   car  
wash, switch of

f the ignition to
avoid
  triggering   the   automatic  
wiping.
In winter

, it is advisable to wait for the
windscreen
  to   completely   clear   of   ice  
before

  operating   the   automatic   wipers.
Automatic wipers
Steering mounted controls
EASE OF USE and COMFORT
4

72
Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015Berlingo-2-VP_en_Chap04_Ergonomie_ed02-2015
Good practice
For maximum cooling or heating of the passenger  compartment,   it   is   possible  
to exceed the value 15 by turning until
LO

  is   displayed   or   the   value   27   by  
turning

  until   HI   is   displayed.
o

n entering the vehicle, the inside
temperature
  may   be   much   colder  
(or
  warmer)   than   is   comfortable.  
There
 
is no advantage in changing the value
displayed

  in   order   to   quickly   reach   the  
level

  of   comfort   required.  
The
  system  
will

  use   its   maximum   performance   to  
reach

  the   comfort   value   set.
DIGITAL AIR CONDITIONING
Automatic operation
AUTO comfort programme
This
  is   the   normal   air   conditioning  
system

  operating   mode. Driver or passenger side comfort
value
The value indicated in the screen
corresponds
  to   a   level   of   comfort   and  
not

  a   temperature   in   degrees   Celsius  
or

  Fahrenheit.
Turn this control to the left
or to the right to decrease or
increase   the   value.  
A 
setting  
around the value 21 provides
optimum

  comfort.   However,  
depending

  on   your   requirements,   a  
setting

  between   18   and   24   is   usual.
d

o not cover the sunshine sensor
located
  on   the   dashboard.
Press this button, the AUTO
symbol
  is   displayed.
The
  system   controls   the  
distribution,

  the   flow   and   the  
intake

  of   air   to   guarantee  
comfort

  and   a   sufficient   circulation  
of

  air   in   the   passenger   compartment  
according

  to   the   comfort   value   set.   No  
further

  action   on   your   part   is   required.Air
  flow   will   increase   gradually   when  
the

engine is cold, to prevent excessive
distribution   of   cold   air.
For   your   comfort,   the   settings   are  
stored when the ignition is switched of

f
and   are   reinstated   the   next   time   the  
vehicle

  is   started.
The   automatic   function   will   no   longer  
be

  maintained   if   you   change   a   setting  
manually

  (AUTO   is   cleared).
SEPARATE SETTINGS FOR DRIVER AND
PASSENGER
Ventilation

11 5
Berlingo-2-VP_en_Chap05_Securite_ed02-2015
The audible (front and rear) and visual
(rear)  parking   sensor   system   consists  
of

  proximity   sensors,   installed   in   the  
rear

  bumper.
The sensors detect any obstacle which
enters
  its   field   of   operation:   person,  
vehicle, tree, fence, behind the vehicle
during

  the   manoeuvre.
Certain
  objects   detected   at   the  
beginning

  of   the   manoeuvre   will   no  
longer be detected at the end of the
manoeuvre

  due   to   the   blind   spots  
between

  and   below   the   sensors.
Examples:
  stake,   roadworks   cone   or  
pavement

  post.
Engage reverse gear
P
ARKING


SENSORS
Display in the screen
An
 
audible
 
signal
 
confirms
 
the
 
activation

 
of
 
the
 
system
 
by
 
engaging
 
reverse

 
gear.
The
 
proximity
 
information
 
is
 
indicated
 
by

 
an
 
audible
 
signal
 
which
 
becomes
 more
 
rapid
 
as
 
the
 
vehicle
 
approaches
 the
 
obstacle.
When the distance between the rear
of the vehicle and the obstacle is less
than
 
approximately
 
thirty
 
centimetres,
 
the

 
audible
 
signal
 
becomes
 
continuous.
Parking sensors
SaFETY
5

11 6
Berlingo-2-VP_en_Chap05_Securite_ed02-2015
Activation / DeactivationMalfunction
In the event of a malfunction, the LED in
  the   button   comes   on,   accompanied  
by

  an   audible   signal   and   a   message   in  
the

  screen.
Contact
  a   CITROËN   dealer   or   qualified  
workshop.
Good practice
In bad weather or in winter, ensure that
the  sensors   are   not   covered   with   mud,  
ice

  or   snow.
The
  system   will   be   deactivated  
automatically

  if   a   trailer   is   being   towed  
or

  if   a   bicycle   carrier   is   fitted   (vehicle  
fitted

  with   a   towbar   or   bicycle   carrier  
recommended

  by   CITROËN).
You can activate or deactivate
the
 
system
 
by
 
pressing
 
this
 
button.
The activation or deactivation
of

 
the
 
system
 
is
 
stored
 
when
 
the

 
vehicle
 
stops.
Engage forward gear
In addition to the rear parking sensors, the   front   parking   sensors   are   triggered  
when an obstacle is detected in
front of the vehicle and the speed
of

  the   vehicle   remains   below   6   mph  
(10 km/h).The

  tone   from   the   speaker   (front  
or rear) allows an obstacle to be
identified

  as   either   in   front   of   or  
behind

  the   vehicle.
Stop the assistance
Change to neutral. The   parking   sensor   system  
cannot,

  in   any   circumstances,  
take

  the   place   of   the   vigilance   and  
responsibility

  of   the   driver.
Parking sensors

 117
Berlingo-2-VP_en_Chap05_Securite_ed02-2015
REVERSING CAMERA
The reversing camera is activated automatically  when   reverse   gear   is  
engaged.
The

  image   is   displayed   in   the   touch  
screen

  tablet.
The
  reversing   camera   function   may   be  
completed

  with   parking   sensors.
The
  reversing   camera   cannot   in  
any

  circumstances   be   a   substitute  
for vigilance on the part of the
driver

. High pressure jet washing
When washing your vehicle, do
not
 
direct
 
the
 
lance
 
within
 
30
 
cm
 
of
 
the

  camera   lens.
The
  superimposed   representation   of  
guide

  lines   helps   with   the   manoeuvre.
They
  are   represented   by   lines   marked  
"on the ground" and do not allow the
position

  of   the   vehicle   to   be   determined  
relative

  to   tall   obstacles   (for   example:  
other

  vehicles,   ...).
Some
  deformation   of   the   image   is  
normal.The blue lines represent the general
direction of the vehicle (the dif

ference
corresponds to the width of your
vehicle
  without   the   mirrors).
The red lines represent a distance of
about
  30   cm   beyond   the   edge   of   your  
vehicle's

  rear   bumper.
The green lines represent distances of
about
  1   and   2   metres   beyond   the   edge  
of

  your   vehicle's   rear   bumper.
The turquoise blue curves represent
the
  maximum   turning   circle.
o

pening the tailgate causes the
display
  to   disappear.
Clean
  the   reversing   camera   regularly  
using

  a   soft,   dry   cloth.
Parking sensors
SaFETY
5