2014 YAMAHA SR400 check oil

PERIODIC MAINTENANCE AND ADJUSTMENT
6-23
1
2
3
4
56
7
8
9
10
11
12 gine as well as other vital parts
of the motorcycle and can lead
to chain slippage or breakage.
To prevent this from occurring,
keep the drive chain slack with-
in the specified limits.
[ECA10572]
TIPUsing the alignment marks on each
side of the swingarm, make sure that
both drive chain pullers are in the sameposition for proper wheel alignment.
6. Take the motorcycle off the center- stand, and then put the sidestand down.
7. Tighten both drive chain puller locknuts, and then tighten the axle
nut and brake torque rod nut to
their specified torques.
8. Adjust the brake pedal free play. (See page 6-18.)
WARNING
EWA10661
After adjusting the brake pedal free
play, check the operation of thebrake light.
9. Make sure that the drive chain pull- ers are in the same position, the
drive chain slack is correct, and
the drive chain moves smoothly.
EAU23026
Cleaning and lubricating the
drive chainThe drive chain must be cleaned and
lubricated at the intervals specified in
the periodic maintenance and lubrica-
tion chart, otherwise it will quickly wear
out, especially when riding in dusty or
wet areas. Service the drive chain as
follows.NOTICE
ECA10584
The drive chain must be lubricated
after washing the motorcycle, ridingin the rain or riding in wet areas.
1. Clean the drive chain with kero- sene and a small soft brush.
NOTICE: To prevent damaging
the O-rings, do not clean the
drive chain with steam cleaners,
high-pressure washers or inap-
propriate solvents.
[ECA11122]
2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a special O-ring chain
lubricant. NOTICE: Do not use
engine oil or any other lubri-
cants for the drive chain, as they
1. Axle nut
2. Drive chain puller locknut
3. Drive chain slack adjusting bolt
4. Alignment marks
1
2
(a) (b)
3
4
Tightening torques:
Drive chain puller locknut:16 Nm (1.6 m·kgf, 12 ft·lbf)
Axle nut: 129 Nm (12.9 m·kgf, 92 ft·lbf)
Brake torque rod nut:
19 Nm (1.9 m·kgf, 14 ft·lbf)
2RD-9-E0.book 23 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

PERIODIC MAINTENANCE AND ADJUSTMENT
6-27
1
2
3
4
56
7
8
9
10
11
12
EAU51951
Checking the front forkThe condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.
To check the condition
Check the front fork for damage and ex-
cessive oil leakage.
To check the operation 1. Place the vehicle on a level sur- face and hold it in an upright posi-
tion. WARNING! To avoid injury,
securely support the vehicle so
there is no danger of it falling
over.
[EWA10752]
2. While applying the front brake, push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.
NOTICE
ECA10591
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-pair it.
EAU45512
Checking the steeringWorn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the pe-
riodic maintenance and lubrication
chart.1. Place the vehicle on the center- stand. WARNING! To avoid inju-
ry, securely support the vehicle
so there is no danger of it falling
over.
[EWA10752]
2. Hold the lower ends of the front fork legs and try to move them for-
ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.
2RD-9-E0.book 27 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

PERIODIC MAINTENANCE AND ADJUSTMENT
6-31
1
2
3
4
56
7
8
9
10
11
12 possibly a fire.
[EWA15132]
4. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
5. If a fuse immediately blows again, have a Yamaha dealer check the
electrical system.
EAU23799
Replacing the headlight bulbThis model is equipped with a halogen
bulb headlight. If the headlight bulb
burns out, replace it as follows.NOTICE
ECA10651
Take care not to damage the follow-
ing parts:
Headlight bulb
Do not touch the glass part of
the headlight bulb to keep it free
from oil, otherwise the transpar-
ency of the glass, the luminosity
of the bulb, and the bulb life will
be adversely affected. Thor-
oughly clean off any dirt and fin-
gerprints on the headlight bulb
using a cloth moistened with al-
cohol or thinner.

Headlight lens
Do not affix any type of tinted
film or stickers to the headlight
lens.
Do not use a headlight bulb of awattage higher than specified. 1. Remove the headlight unit by re-
moving the screws.
Specified fuses:Main fuse:30.0 A
Signaling system fuse: 15.0 A
Headlight fuse:
15.0 A
Ignition fuse: 10.0 A
Backup fuse: 7.5 A
Fuel injection system fuse:
7.5 A
Parking lighting fuse: 7.5 A
1. Do not touch the glass part of the bulb.
1. Screw1
2RD-9-E0.book 31 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

MOTORCYCLE CARE AND STORAGE
7-4
1
2
3
4
5
678
9
10
11
12
2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to pro- tect the cylinder, piston rings, etc.
from corrosion.
a. Remove the spark plug cap and spark plug.
b. Pour a teaspoonful of engine oil into the spark plug bore.
c. Install the spark plug cap onto the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)
d. Turn the engine over several times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING! To
prevent damage or injury
from sparking, make sure to
ground the spark plug elec-
trodes while turning the en-
gine over.
[EWA10952]
4. Lubricate all control cables and the pivoting points of all levers and
pedals as well as of the sidestand/
centerstand.
5. Check and, if necessary, correct the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlet with a plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0 C (30 F) or more than 30
 C (90 F)]. For more information
on storing the battery, see page
6-28.TIPMake any necessary repairs beforestoring the motorcycle.
2RD-9-E0.book 4 ページ ２０１３年１１月２８日　木曜日　午後４時１８分

10-1
1
2
3
4
5
6
7
8
91011
12
INDEX
AAir filter element, replacing ...................... 6-12
Auxiliary light bulb, replacing ................... 6-34BBattery ..................................................... 6-28
Brake and clutch levers, checking and lubricating .............................................. 6-25
Brake fluid, changing ............................... 6-21
Brake fluid level, checking ....................... 6-20
Brake lever ................................................ 3-6
Brake lever free play, adjusting ............... 6-17
Brake light switches ................................. 6-19
Brake pads and shoes, checking............. 6-20
Brake pedal ............................................... 3-6
Brake pedal, checking and lubricating ..... 6-25
Brake pedal height and free play, adjusting ................................................ 6-18CCables, checking and lubricating ............. 6-24
Care ........................................................... 7-1
Catalytic converter ..................................... 3-9
Centerstand and sidestand, checking and lubricating ....................................... 6-26
Clutch lever................................................ 3-5
Clutch lever free play, adjusting .............. 6-16DDecompression lever ............................... 3-11
Dimmer switch ........................................... 3-4
Drive chain, cleaning and lubricating ....... 6-23
Drive chain slack ..................................... 6-22EEngine break-in ......................................... 5-3
Engine idling speed, checking ................. 6-13
Engine oil and oil filter element.................. 6-9 Engine serial number ................................ 9-1
Engine stop switch .................................... 3-5
Engine trouble warning light ...................... 3-3
FFront fork, checking................................. 6-27
Fuel ........................................................... 3-7
Fuel cock ................................................. 3-10
Fuel consumption, tips for reducing .......... 5-3
Fuel level warning light .............................. 3-3
Fuel tank breather/overflow hose .............. 3-9
Fuel tank cap............................................. 3-7
Fuses, replacing ...................................... 6-29HHandlebar switches ................................... 3-4
Hazard switch............................................ 3-5
Headlight bulb, replacing......................... 6-31
High beam indicator light ........................... 3-3
Horn switch ............................................... 3-5IIdentification numbers ............................... 9-1
Ignition circuit cut-off system ................... 3-13
Indicator lights and warning lights ............. 3-2KKickstarter ............................................... 3-10MMain switch/steering lock .......................... 3-1
Maintenance and lubricatio
n, periodic....... 6-4
Maintenance, emission control system ..... 6-3
Matte color, caution ................................... 7-1
Model label ................................................ 9-2NNeutral indicator light ................................ 3-2PPanel, removing and installing .................. 6-7 Parking.......................................................5-4
Part locations .............................................2-1
Pass switch ................................................3-4
SSafety information ......................................1-1
Seat ......................................................... 3-11
Shifting .......................................................5-2
Shift pedal ..................................................3-6
Shift pedal, checking................................ 6-19
Shock absorber assemblies, adjusting ....3-12
Sidestand .................................................3-12
Spark plug, checking .................................6-8
Specifications.............................................8-1
Speedometer unit ......................................3-3
Starting the engine.....................................5-1
Starting the engine, trouble........................5-2
Steering, checking ................................... 6-27
Storage ......................................................7-3
Swingarm pivots, lubricating .................... 6-26TTachometer................................................3-4
Tail/brake light bulb, replacing ................. 6-32
Throttle grip and cable, checking and
lubricating ..............................................6-24
Throttle grip free play, checking............... 6-13
Tires ......................................................... 6-14
Tool kit .......................................................6-2
Troubleshooting ....................................... 6-39
Troubleshooting chart ..............................6-40
Turn signal indicator light ...........................3-2
Turn signal light bul b, replacing ............... 6-33
Turn signal switch ......................................3-4VValve clearance ....................................... 6-13
2RD-9-E0.book 1 ページ ２０１３年１１月２８日　木曜日　午後４時１８分