2014 VOLVO XC90 buttons

02 Instruments and controls
HomeLink®
Wireless Control System*
02
90* Option/accessory, for more information, see Introduction.
NOTE
Some devices may require you to replace this Programming Step 2 with proceduresnoted in the “Gate Operator / CanadianProgramming” section. If the HomeLinkindicator light does not change to a rapidlyblinking light after performing these steps,contact HomeLink at www.homelink.comor by phoning the hotline at1–800–355–3515.
3. Firmly press, hold for five seconds and
release the programmed HomeLink but-
ton up to two separate times to activate the door. If the door does not activate,press and hold the just-trained HomeLinkbutton and observe the indicator light.
• If the indicator light
stays on con-
stantly, programming is complete and your device should activate when the HomeLink button is pressed andreleased.
• If the indicator light blinks
rapidly for
two seconds and then turns to aconstant light continue with “Pro- gramming” steps 4-6 to complete the
programming of a rolling code equip- ped device (most commonly a garagedoor opener). 4. At the garage door opener receiver
(motor-head unit) in the garage, locate the “learn” or “smart” button. This canusually be found where the hangingantenna wire is attached to the motor-head unit.
5. Firmly press and release the “learn” or “smart” button. (The name and color ofthe button may vary by manufacturer.)There are 30 seconds to initiate step 6.
6. Return to the vehicle and firmly press, hold for two seconds and release the pro-grammed HomeLink button. Repeat the“press/hold/release” sequence a secondtime, and, depending on the brand of thegarage door opener (or other rolling codeequipped device), repeat this sequence athird time to complete the programmingprocess.
HomeLink should now activate your rollingcode equipped device.
Gate Operator/Canadian ProgrammingCanadian radio-frequency laws require trans-mitter signals to “time-out” (or quit) after sev-eral seconds of transmission – which may notbe long enough for HomeLink to pick up thesignal during programming. Similar to thisCanadian law, some U.S. gate operators aredesigned to “time-out” in the same manner. If you live in Canada or you are having diffi-culties programming a gate operator orgarage door opener by using the “Program-ming” procedures,
replace “Programming
HomeLink” step 2 with the following :
• Continue to press and hold the HomeLink button while you
press and release -
every two seconds (“cycle”) your hand-
held transmitter until the HomeLink indi-cator light changes from a slow to a rap-idly blinking light. Now you may releaseboth the HomeLink and hand-held trans-mitter buttons.
Proceed with “Programming” step 3 to com- plete.
Using HomeLink
To operate, simply press and hold the pro- grammed HomeLink button until the traineddevice begins to operate (this may take sev-eral seconds). Activation will now occur forthe trained device (i.e., garage door opener,gate operator, security system, entry doorlock, home/office lighting, etc.). For conven-ience, the hand-held transmitter of the devicemay also be used at any time. In the eventthat there are still programming difficulties orquestions, contact HomeLink at:www.homelink.com or by phoning the hotlineat 1–800–355–3515.

02 Instruments and controls
HomeLink®
Wireless Control System*
02
* Option/accessory, for more information, see Introduction.91
NOTE
If the ignition is switched off, HomeLink will function for 30 minutes after the driv-er's door has been opened.
Resetting HomeLink Buttons
Use the following procedure to reset (erase programming) from the three HomeLink but-tons (individual buttons cannot be reset butcan be “reprogrammed” as outlined in the fol-lowing section):
1. Press and hold the two outer HomeLink
buttons until the indicator light begins to flash.
2. Release both buttons. > HomeLink is now in the training (orlearning) mode and can be pro-grammed at any time beginning with“Programming” - step 1.
Reprogramming a Single HomeLink Button
To program a device to HomeLink using a HomeLink button previously trained, followthese steps:
1. Press and hold the desired HomeLink button. DO NOT release the button.
2. The indicator light will begin to flash after 20 seconds. Without releasing the Home- Link button, proceed with “Programming”- step 1.
For questions or comments, contact Home-Link at: www.homelink.com or phone 1–800–355–3515. This device complies with FCC rules part 15 and Industry Canada (IC) RSS-210. Operationis subject to the following two conditions: (1)This device may not cause harmful interfer-ence, and (2) This device must accept anyinterference that may be received includinginterference that may cause undesired opera-tion.
NOTE
The transmitter has been tested and com- plies with FCC and IC rules. Changes ormodifications not expressly approved bythe party responsible for compliance couldvoid the user’s authority to operate the device. 2
2
The term “IC:” before the certification/registration number only signifies that Industry Canada technical specifications were met.

03 Climate
Electronic climate control (ECC)
03
100* Option/accessory, for more information, see Introduction.
switch will light up to indicate that the defrost function is engaged.
• Blower speed increases automatically and the air conditioning will switch on (ifnot already on and if the passenger com-partment blower is not turned off) todehumidify the air in the passenger com-partment.
• Recirculation will not function whiledefrost is engaged.
The climate system will return to its previous settings when the defroster function isswitched off.
Rear window and door mirror
defrosters
This function defrosts/deices the rear window and door mirrors. The LED in the switch willlight up to indicate that the heating function isengaged. For additional information on thisfunction see page 75. Never use ice scrapers made of metal as they can easily scratch the mirror surface.
Heated front seats*
1. Press the switch once for maximum seat heating. Both LEDs in the switch will be lit. 2. Press the switch a second time for com-
fort heating. One LED in the switch will belit.
3. Press the switch a third time to turn the heating off completely. The LED will gooff.
The seat heating for the passenger seatshould be switched off when the seat is notoccupied.
Heated rear seats (XC90 Executive*)
G030976
Button for rear seat heating Heating for the respective outboard rear seats can be switched on or off with buttons on either side of the center console (see theillustration). To switch on rear seat heating:
–Press the button.
> The symbol in the button will illumi-
nate.
To switch off rear seat heating:
–Press the button.
> The symbol in the button will go out.
Temperature
These controls are used to individually set the temperature for both sides of the passengercompartment. Please note that the compart-ment will not be heated or cooled faster bysetting the temperature higher or lower thannecessary. Set the control to the temperature you prefer.
Blower control 1
Turn the control clockwise to increase or counterclockwise to decrease the blowerspeed. Pressing the
AUTO switch will auto-
matically regulate blower speed and overridemanual adjustment. Turning the blower control counterclockwise until an orange LED comes on will turn boththe blower and the air conditioning off.
1 See also see page 94.

04 Interior
Front seats
04
* Option/accessory, for more information, see Introduction.105
Power seat*
OperationDriver's seat: The seat can be adjusted if the
ignition key is in position I, II or if the engine
is running. It can also be adjusted as follows with the ignition off:
• Within several minutes after the driver's door has been unlocked from the outside,has been opened, and remains open.
• Within a short period if the driver's doorhas just been closed.
• Within a short period if the driver's doorhas not been opened after the ignitionhas been switched off.
Passenger seat: The seat can only be
adjusted if the ignition key is in position I, II or
if the engine is running.
G027036
Power seat adjustment controls
Seat adjustmentAdjust the power seat(s) with the two controls at the side of the seat as follows:
Front edge of seat (raise/lower)
Forward – rearward
Rear edge of seat (raise/lower)
Backrest tilt
NOTE
The power seats have an overload protec- tor that activates if a seat is blocked byany object. If this occurs, switch off theignition (key in position 0 ) and wait for ashort period before operating the seatagain.
Emergency stopIf the seat accidentally begins to move, press any of the buttons to stop the seat.
NOTE
Please refer to the following page for infor- mation on programming the memory func-tion in the driver's seat.
Remote keyless entry system and the driver's seat
The remote key transmitter also controls the position of the electrically operated driver'sseat in the following way:
• Adjust the seat to your preferences.
• When you leave your vehicle, lock it using the remote key.
The position of the seat is now stored in the remote key.

04 Interior
Front seats
04
106* Option/accessory, for more information, see Introduction.
Automatic seat adjustmentTo move the seat to the position in which you left it:
1. Unlock the driver's door with the same
remote key (the one used to lock the doors)
2. Open the driver's door within 2 minutes. The driver's seat will automatically move to the position in which you left it.
NOTE
• The seat will move to this position even if someone else has moved it to adifferent seating position and lockedthe vehicle with a different remote key.
• This feature will work in the same waywith all of the remote key transmitters(up to 3 ) that you use with your vehi-cle.
• This feature will not function if you lockyour vehicle with the key.
WARNING
•Because the driver's seat can be adjusted with the ignition off, childrenshould never be left unattended in thevehicle.
• Movement of the seat can be STOP-PED at any time by pressing any but-ton on the power seat control panel.
• Do not adjust the seat while driving.
• The seat should be adjusted so thatthe brake pedal can be depressedfully. In addition, position the seat asfar rearward as comfort and controlallow.
• The seat rails on the floor must not beobstructed in any way when the seat isin motion.
G027037
Programming the memoryThree different seating and door mirror posi- tions can be stored in the driver seat's mem-ory. The following example explains how button 1 can be programmed. Buttons 2 and 3 can beprogrammed in the same way. To program (store) a seat position in button 1:
1. Move the seat to the desired position
using the seat adjustment controls (see page 104).
2. Press and hold down the MEM (memory)
button.

04 Interior
Interior lighting
04
}}
111
Reading lights and courtesy light
G026960
Driver's side front reading lamp
Courtesy lights
Passenger's side front reading lamp The reading lights can be switched on or offby pressing buttons 1 or 3. The courtesylighting (including footwell lighting) can beturned on or off by pressing button 2.This also activates the automatic func-tion.
G027153
Rear reading lights
Driver's side rear reading light
Passenger's side rear reading light. The rear reading lights can be switched onand off by pressing buttons (4) or (5).
Automatic functionThe reading lights and courtesy lights willswitch off automatically approximately10 minutes after the engine has been turnedoff. The lights can be turned off sooner bypressing the respective buttons.The courtesy lights come on automatically
1
and remain on for approximately 30 secondswhen: • The vehicle has been unlocked from the outside with the remote key or key blade
• If the engine has been switched off andthe ignition key has been turned to posi-tion 0
The courtesy lights will come on and remain on for approximately 10 minutes when:
• One of the doors is opened (assuming the courtesy lighting has not previously beenswitched off)
The courtesy lighting will go off when:
• The engine is started
• The vehicle is locked from the outsidewith the remote key or key blade
The automatic function can be disconnected by pressing button (2) for more than 3 sec-onds. Briefly pressing the button again automati- cally reconnects the function. The courtesy light timer periods can be changed. Contact a trained and qualifiedVolvo service technician.
1 This function is light dependent and is only activated in dark conditions.

04 Interior
Securing cargo
04
120
Attachment eyelet in front seat rail
If the vehicle is equipped with the cargo area cover, lift the cover out of the vehicle beforeinstalling the cargo net.
1. The upper and lower rods of the cargo net are hinged. Position the rods so that they are straight and lock in position.
2. Insert the end of the upper rod in one of the attachment brackets (see illustrationin the left column).
3. Insert the other end of the rod in the attachment bracket on the opposite sideof the vehicle.
NOTE
When using the net in the rear attachment brackets, be sure it is installed in front ofthe side armrests.
4. Attach the lower straps to the eyelets onthe floor if the net has been installed in the rear attachment brackets. Use theeyelets in the front seat rails if the net hasbeen installed in the forward attachmentbrackets.
5. Adjust the straps to pull the net taut.
Folding and storing the cargo netPress the release buttons on the hinges (1 in the illustration) and fold the net.
WARNING
• Be sure the cargo net is properly inserted in the attachment bracketsand the straps are correctly attachedto the eyelets and pulled taut.
• Do not use the net if it is damaged inany way.
• When it is not in use, store the net sothat it cannot be thrown forward in theevent of sudden braking, etc.
G027056
Upper attachments

05 Locks and alarm
Remote keys and key blades
05
129
WARNING
Never use the transmitter to lock the doors from inside the vehicle.• Doing so would ACTIVATE:
• the break-in alarm, which would sound if one of the doors were opened
• the optional interior motion and incli-nation alarm sensors.
• Doing so would DEACTIVATE:
• the moonroof and interior courtesylight controls.
• the central locking buttons on the frontdoor armrests, although the interiordoor handles would still function toallow occupants to leave the vehicle.
• Disabled features would remain disa-bled until the remote is used again tounlock the vehicle.
• In addition, locking an occupied vehi-cle would hinder rapid access to theoccupants in an accident or emer-gency.
Replacing the battery in the remote keyIf the range of the transmitter is noticeably reduced, this indicates that the battery isweak and should be replaced.
To replace the battery:1. Carefully pry open the rear edge of the
cover with a small screwdriver.
2. Insert a new 3-volt, CR2032 battery, with the battery's plus side up. Avoid touching the contact surfaces of the battery withyour fingers.
3. Press the cover back into place. Ensure that the rubber seal is correctly posi-tioned to help keep out moisture.
NOTE
The old battery should be disposed of properly at a recycling center or at yourVolvo retailer.