Favorite destinations on the map
A favorite category can be specified for stored destinations. Favorite destinations can be displayed on the map with the orange favorite icon assigned to them (private T or business P).
The list of favorite destinations is called up from the Destination entry menu.
Points of interest on the map
Points of interest can be selected as a navigation destination.
Points of interest are divided into point of interest categories. These point of interest categories are assigned to blue point of interest icons (such as * hotel and , petrol station). A list of available point of interest categories can be called up from the Map settings menu. Map icons can be selected there for display.
Display detailed information on points of interest
x Press the symbol on the map briefly to display a window with further information.
Due to the map scale, there may be several entries behind one symbol on the map, in which case a list appears for selecting an entry.
x Select the required entry by pressing.
Function keys for further operation are displayed in the information window that appears.
x Selecting points of interest and favorite destinations from the map.
x TMC traffic reports on the map.
3D models on the map
An abstract 3D city model can be displayed in the 6 3D display type for some cities (such as Berlin).
In addition, special historical buildings and sights of interest are displayed as photo-realistic 3D models.
To display these, autozoom needs to be switched off in some cases and you have to zoom further into the map.
The display of 3D city models and 3D sights of interest is enabled and disabled in the map settings.
If no symbols or 3D models can be displayed due to the scale, turn the setting knob clockwise
⇒ fig. 133 (3) in order to zoom in on the map.
Map settings: selecting map symbols
x Unscrew the valve core from the tire valve using the valve core wrench ⇒ fig. 326 (1) and place it on a clean surface.
x Vigorously shake the tire inflation cylinder ⇒ fig. 326 (10) a few times back and forth.
x Tightly screw the filling hose ⇒ fig. 326 (3) to the tire inflation bottle (turn clockwise). The foil on the seal is automatically pierced.
x Remove the sealing plug from the filling hose ⇒ fig. 326 (3) and slide the open end onto the tire valve.
x Hold the cylinder with the bottom pointing up and fill the entire contents of the tire inflation cylinder into the tire.
x Detach the empty tire inflation cylinder from the valve.
x Using the valve core wrench ⇒ fig. 326 (1) screw the valve core back into the tire valve.
Inflating the tire
x Screw the tire inflation hose ⇒ fig. 326 (5) of the air compressor tightly to the tire valve.
x Check whether the air release valve ⇒ fig. 326 (7) is screwed on tightly.
x Open the engine hood ⇒ Working in the engine compartment.
x Attach the cable clips ⇒ fig. 326 (9) only to the jump-start terminals in the engine compartment
⇒ fig. 327. The red clip on the compressor cable is connected to the positive (+) terminal; the black clip is connected to the negative terminal (—).
x Start the vehicle engine and let it run.
x Switch the air compressor on using the ON / OFF switch ⇒ fig. 326 (8),
x Let the air compressor run until a pressure of 36 – 44 psi (250 - 300 kPa) is reached ⇒ .
Maximum run time 8 minutes ⇒ .
x Switch off the air compressor.
x If an air pressure of 36 – 44 psi (250 - 300 kPa) cannot be reached, unscrew the tire inflation hose from the tire valve.
x Drive about 30 feet (10 meters) backwards or forwards so that the sealant can be distributed inside the tire.
x Connect the tire inflation hose of the air compressor again to the tire valve and repeat the inflation process.
x If the required tire pressure still cannot be reached, the tire is too badly damaged. The tire cannot
be sealed using the tire mobility set. Do not drive the vehicle. Get professional assistance ⇒ .
x Disconnect the air compressor and unscrew the tire inflation hose from the tire valve.
x If a tire pressure of 36 – 44 psi (250 – 300 kPa) is reached, continue driving right away and drive at a speed of not more than 50 mph (80 km/h).
x Check tire pressure after 10 minutes of driving ⇒ Check after 10 minutes of driving.
WARNING
The tire inflation hose and air compressor can get hot during inflation.
x Protect hands and skin from hot parts.
x Do not place the hot tire inflation hose or hot air compressor on flammable material.
x Let the equipment cool off almost completely before stowing it.
x If the tire cannot be inflated to at least 36 psi (250 kPa), the damage is too great to be repaired with the tire mobility set. The sealant is not able to seal the tire. Do not drive the vehicle. Get professional assistance.
