2014 TOYOTA URBAN CRUISER stop start

434
5-1. Essential information
URBAN CRUISER_OM_OM52F47E_(EE)
Using a flat bed truck If you use chains or cables to tie
down your vehicle, the angles
shaded in black must be 45°.
Do not overly tighten the tie
downs or the vehicle may be
damaged.
■ Before emergency towing
Vehicles without smart entry & start system
Put the shift lever in “N”.
Put the engine switch in the “ACC” (engine off) or “ON” position
(engine running).
Release the parking brake.
Vehicles with smart entry & start system Put the shift lever in “N”.
The “ENGINE START STOP” switch must be in the ACCESSORY
mode (engine off) or IGNITION ON mode (engine running).
Release the parking brake.
■ Emergency towing eyelet location
→ P. 449, 465
STEP1
STEP2
STEP3
STEP1
STEP2
STEP3

436
5-1. Essential information
URBAN CRUISER_OM_OM52F47E_(EE)
NOTICE
■ To prevent causing serious damage to the transmission when towing
using a wheel-lift type truck (4WD models)
Never tow this vehicle with any of the wheels in contact with the ground.
■ To prevent damaging the vehicle
●Vehicles without smart entry & start system: Do not tow the vehicle with
the engine switch to the “LOCK” position.
Vehicles with smart entry & start system: Do not tow the vehicle with the
“ENGINE START STOP” switch OFF.
The steering lock mechanism is not strong enough to hold the front wheel
straight. (2WD models)
● When raising the vehicle, ensure adequate ground clearance for towing at
the opposite end of the raised vehicle. Without adequate clearance, the
vehicle could be damaged while being towed.
■ To prevent body damage when towing with a sling-type truck
Do not tow with a sling-type truck, either from the front or rear.

438
5-1. Essential information
URBAN CRUISER_OM_OM52F47E_(EE)
Fuel pump shut off system (gasoline engine)
Follow the procedure below to restart the engine after the system is
activated.Vehicles without smart entry & start system:
Turn the engine switch to the “ACC” or “LOCK” position.
Vehicles with smart entry & start system:
Turn the “ENGINE START STOP” switch to the ACCESSORY
mode or OFF.
Restart the engine.
NOTICE
■Before starting the engine
Inspect the ground under the vehicle.
If you find that fuel has leaked on to the ground, the fuel system has been
damaged and is in need of repair. Do not restart the engine.
To minimize the risk of fuel leakage when the engine stalls or an air-
bag inflates upon collision, the fuel pump shut off system stops sup-
plying fuel to the engine.
STEP1
STEP2

444
5-2. Steps to take in an emergency
URBAN CRUISER_OM_OM52F47E_(EE)
Warning lightWarning light/DetailsCorrection procedure
(Flashes) Engine oil change
reminder light
(diesel engine)
Check the engine oil, and
change if necessary. After
changing the engine oil, the
oil change system should
be reset. (→P. 375)
Indicates that the engine
oil is scheduled to be
changed.
Flashes approximately
14500 km (9000 miles)
after the engine oil is
changed. ( →P. 447) (The
indicator will not work
properly unless the oil
maintenance date has
been reset.)
Indicates that the engine
oil should be changed. • Flashes while you are driving.
• Vehicles without smart entry & start system:
Flashes for about 12
seconds when the
engine switch turned to
the “ON” position.
• Vehicles with smart entry & start system:
Flashes for about 12
seconds when the
“ENGINE START
STOP” switch turned to
the IGNITION ON
mode.

446
5-2. Steps to take in an emergency
URBAN CRUISER_OM_OM52F47E_(EE)
Follow the correction procedures. (vehicles with smart entry &
start system) After taking the specified steps to correct the suspected problem,
check that the warning light turn off.
InteriorbuzzerExterior buzzerWarning lightWarning
light/DetailsCorrection procedure
Once3 times
A passenger has
removed the smart
key from the vehi-
cle while the
engine is not OFF.
Check
whether the
passenger
leaving the
vehicle is car-
rying the smart
key
Once(Comes on for 5 seconds)
The vehicle’s ID
code detection
system has judged
that the smart key
is not present
when the
“ENGINE START
STOP” switch is
pressed.
Check that the
smart key is in
the vehicle
and within the
detection area.

5
485
5-2. Steps to take in an emergency
When trouble arises
URBAN CRUISER_OM_OM52F47E_(EE)
Starting the engine
Shift the shift lever to “N” and depress the clutch pedal. Touch the Toyota emblem side of
the electronic key to the
“ENGINE START STOP” switch.
An alarm will sound to indicate
that the start function cannot
detect the electronic key that is
touched to the “ENGINE START
STOP” switch if any of the doors
is opened while the key is
touched to the switch.
Press the “ENGINE START STOP” switch within 5 seconds
after the buzzer sounds, keeping the clutch pedal depressed.
In the event that the “ENGINE START STOP” switch still cannot be
operated, contact any authorized Toyota dealer or repairer, or another
duly qualified and equipped professional.
STEP1
STEP2
STEP3

486
5-2. Steps to take in an emergency
URBAN CRUISER_OM_OM52F47E_(EE)
■ Stopping the engine
Shift the shift lever to “N” and press the “ENGINE START STOP” switch as
you normally do when stopping the engine.
■ Replacing the key battery
As this procedure is a temporary measure, it is recommended that the elec-
tronic key battery be replaced immediately when the battery depletes.
(→ P. 399)
■ Alarm
Using the mechanical key to lock the doors will not set the alarm system.
If a door is unlocked using the mechanical key when the alarm system is set,
the alarm may be triggered. ( →P. 120)
■ Changing “ENGINE START STOP” switch modes
Within 5 seconds of the buzzer sounding, release the clutch pedal and press
the “ENGINE START STOP” switch.
The engine does not start and modes will be changed each time the switch
is pressed. ( →P. 186)

5
489
5-2. Steps to take in an emergency
When trouble arises
URBAN CRUISER_OM_OM52F47E_(EE)
Remove the engine cover
Positive (+) battery terminal on your vehicle
Positive (+) battery terminal on the second vehicle
Negative (-) battery terminal on the second vehicle
Connect the jumper cable to ground on your vehicle as shown in
the illustration.
Start the engine of the second vehicle. Increase the engine
speed slightly and maintain at that level for approximately 5
minutes to recharge the battery of your vehicle.
Vehicles with smart entry & start system: Open and close
any of the doors with the “ENGINE START STOP” switch
OFF.
Vehicles without smart entry & start system: Maintain the
engine speed of the second vehicle and turn the engine
switch to the “ON” position, then start the vehicle’s engine.
Vehicles with smart entry & start system: Maintain the
engine speed of the second vehicle and turn the “ENGINE
START STOP” switch to the IGNITION ON mode, then start
the vehicle’s engine.
Once the vehicle’s engine has started, remove the jumper
cables in the exact reverse order in which they were con-
nected.
STEP3
STEP4
STEP5
STEP6