2014 TOYOTA DYNA 100/150 lock

SEATS, SEAT BELTS, STEERING WHEEL AND MIRRORS27
When returning the bottom cushion to its
original position, hang the strap on the
hook.
CAUTION
DAny operations should not be made
while the vehicle is moving.
DAfter raising the bottom cushion,
make sure to secure it with the
holding strap.
DWhen returning the bottom cushion
to its original position, observe the
following precautions in order to
prevent death or serious injury in a
collision or sudden stop:
Make sure the bottom cushion is
securely locked by trying to pull up
the edge of the bottom cushion.
Failure to do so will prevent the
seat belt from operating properly.
Make sure the seat belts are not
twisted or caught under the bottom
cushion and are arranged in their
proper position and are ready to
use.
The head restraints can be removed.
For your safety, always use the head
restraints in the locked position.
To remove: Pull it up while pressing the
lock release button.
When an occupant sits on the rear seat,
always pull up the head restraint to the
lock position.
The head restraint is most effective when
it is close to your head. Therefore, using
a cushion on the seatback is not recom-
mended.
CAUTION
DUse the head restraint designed for
each respective seat.
DMake sure the head restraint is
locked in position.
DDo not drive with the head re-
straints removed.
Dyna100/150_EE
Head restraints (rear seats)

30SEATS, SEAT BELTS, STEERING WHEEL AND MIRRORS
Adjust the seat as needed (driver ’s seat
only) and sit up straight and well back
in the seat. To fasten your belt, pull it
out of the retractor and insert the tab
into the buckle.
You will hear a click when the tab locks
into the buckle.
The seat belt length automatically adjusts
to your size and the seat position.
The retractor will lock the belt during a
sudden stop or on impact. It also may
lock if you lean forward too quickly. A
slow, easy motion will allow the belt to
extend, and you can move around freely.
If the seat belt cannot be pulled out of the
retractor, firmly pull the belt and release
it. You will then be able to smoothly pull
the belt out of the retractor.
CAUTION
DAfter inserting the tab, make sure
the tab and buckle are locked and
the belt is not twisted.
DDo not insert coins, clips, etc. in
the buckle as this may prevent you
from properly latching the tab and
buckle.
DIf the seat belt does not function
normally, immediately contact any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional. Do not use
the seat until the seat belt is fixed,
because it cannot protect an adult
occupant or your child from death
or serious injury.
Dyna100/150_EE
—3−point type

SEATS, SEAT BELTS, STEERING WHEEL AND MIRRORS31
Seat belts with an adjustable shoulder
anchor—
Adjust the shoulder anchor position to
your size.
To raise: Slide the anchor up.
To lower: Push in the lock release button
and slide the anchor down.
After adjustment, make sure the anchor is
locked in position.
CAUTION
Always make sure the shoulder belt
is positioned across the center of
your shoulder. The belt should be
kept away from your neck, but not
falling off your shoulder.Failure to
do so could reduce the amount of
protection in an accident and cause
death or serious injuries in a colli-
sion.
Ta k e u p
slack
To o h i g h
Keep as low on
hips as possible
Adjust the position of the lap and
shoulder belts.
Position the lap belt as low as possible
on your hips—not on your waist, then ad-
just it to a snug fit by pulling the shoulder
portion upward through the latch plate.
CAUTION
DBoth high−positioned lap belts and
loose−fitting belts could cause
death or serious injuries due to
sliding under the lap belt during a
collision or other unintended result.
Keep the lap belt positioned as low
on hips as possible.
DFor your safety, do not place the
shoulder belt under your arm.
Dyna100/150_EE

32SEATS, SEAT BELTS, STEERING WHEEL AND MIRRORS
To release the belt, press the buckle
release button and allow the belt to
retract.
If the belt does not retract smoothly, pull
it out and check for kinks or twists. Then
make sure it remains untwisted as it re-
tracts.
Lengthen
Front seat
Lengthen
Rear seat
Sit up straight and well back in the
seat. To fasten your belt, insert the tab
into the buckle.
You will hear a click when the tab locks
into the buckle.
If the belt is not long enough for you, hold
the tab at a right angle to the belt and
pull on the tab.
Dyna100/150_EE
—2−point type

SEATS, SEAT BELTS, STEERING WHEEL AND MIRRORS33
CAUTION
DAfter inserting the tab, make sure
the tab and buckle are locked and
the belt is not twisted.
DDo not insert coins, clips, etc. in
the buckle as this may prevent you
from properly latching the tab and
buckle.
DIf the seat belt does not function
normally, immediately contact any
authorized Toyota dealer or repairer,
or another duly qualified and
equipped professional. Do not use
the seat until the seat belt is fixed.
It cannot protect an adult occupant
or your child from death or serious
injury.
Adjust to
a snug fit
Keep as low on
hips as possibleTo o h i g h
Front seat
To o h i g h
Adjust to a
snug fit
Keep as low on
hips as possible
Rear seat
Remove excess length of the belt and
adjust the belt position.
To shorten the belt, pull the free end of
the belt.
Position the lap belt as low as possible
on your hips—not on your waist, then ad-
just it to a snug fit.
Dyna100/150_EE

36SEATS, SEAT BELTS, STEERING WHEEL AND MIRRORS
The driver ’s seat belt pretensionersystem
mainly consists of the following compo-
nents and their locations are shown in the
illustration.
1. SRS warning light
2. Airbag sensor
3. Driver ’s seat belt pretensioner assem-
bly
4. Airbag sensor assembly
The driver ’s seat belt pretensioner is con-
trolled by the airbag sensor assembly. The
airbag sensor assembly consists of a saf-
ing sensor and airbag sensor.
When the driver ’s seat belt pretensioner is
activated, an operating noise may be
heard and a small amount of smoke−like
gas may be released. This gas is harm-
less and does not indicate that a fire is
occurring.
Once the driver ’s seat belt pretensioner
has been activated, the seat belt retractor
remains locked.
If the vehicle is involved in multiple colli-
sions, the pretensioner will activate for the
first collision, but will not activate for the
second or subsequent collisions.
CAUTION
Observe the following precautions to
reduce the risk of injury in the event
of sudden braking or an accident.
Failure to do so may cause death or
serious injury.
DIf the pretensioner has activated,
the SRS warning light will come on.
In that case, the seat belt cannot
be used again and must be re-
placed at any authorized Toyota
dealer or repairer, or another duly
qualified and equipped professional.
DDo not modify, remove, strike or
open the seat belt pretensioner as-
semblies, airbag sensor or sur-
rounding area or wiring. Consult
any authorized Toyota dealer or re-
pairer, or another duly qualified and
equipped professional about any re-
pair and modification.
Dyna100/150_EE

SEATS, SEAT BELTS, STEERING WHEEL AND MIRRORS45
A child restraint system for a small
child or baby must itself be properly
restrained on the seat with either the
lap belt or the lap portion of the lap/
shoulder belt. You must carefully con-
sult the manufacturer ’s instructions
which accompany the child restraint
system.
To provide proper restraint, use a child
restraint system following the manufactur-
er ’s instructions about the appropriate age
and size of the child for the child restraint
system.
Toyota recommends that you use a child
restraint system which conforms to the
regulation “ECE No.44”.
Install the child restraint system correctly
following the instructions provided by its
manufacturer. General directions are also
provided under the following illustrations.
The child restraint system should be
installed on the rear seat. According to
accident statistics, the child is safer when
properly restrained in the rear seat than
in the front seat.CAUTION
When the child restraint system is
not in use:
DKeep the child restraint system
properly secured on the seat even
if it is not in use. Do not store the
restraint unsecured in the passen-
ger compartment.
DIf it is necessary to detach the
child restraint system, remove it
from the vehicle or store it securely
in the luggage compartment. This
will prevent it from injuring passen-
gers in the event of a sudden stop,
sudden swerve or accident.
DAfter installing the child restraint
system, make sure it is secured in
place following the manufacturer ’s
instructions. If it is not restrained
securely, it may cause death or se-
rious injury to the child in the
event of a sudden stop, sudden
swerve or accident.
When installing a child restraint system
witha3−point seat belt, you will need a
locking clip.
If your child restraint systemdoes not
provide a locking clip, you can purchase
the following item from any authorized
Toyota dealer or repairer, or another duly
qualified and equipped professional.
Locking clip for child restraint system
(Part No. 73119−22010)
Dyna100/150_EE
—Child restraint system

SEATS, SEAT BELTS, STEERING WHEEL AND MIRRORS49
CAUTION
Do not install a child restraint system
on the front center position. This seat
position is not designed to hold a
child restraint system.
If used in the front center position,
depending on its type, the child re-
straint system may interfere with the
proper usage of the driver ’s and front
passenger ’s seat belts. It may also
hamper your driving.
To install the child seat:
1. Run the center lap belt through or
around the child seat following the
instructions provided by its manufactur-
er and insert the tab into the buckle
taking care not to twist the lap belt.
CAUTION
DAfter inserting the tab, make sure
the tab and buckle are locked and
that the lap belt is not twisted.
DDo not insert coins, clips, etc. in
the buckle as this may prevent your
child from properly latching the tab
and buckle.
DIf the seat belt does not function
normally, it cannot protect your
child from death or serious injury.
Contact any authorized Toyota
dealer or repairer, or another duly
qualified and equipped professional,
immediately. Do not install the child
restraint system on the seat until
the seat belt is fixed.
Dyna100/150_EE