2014 SKODA YETI height

WARNING■The front passenger airbag should be switched off when transporting ob-
jects on the seat which was folded forwards » page 22, Deactivating the
front passenger airbag .■
Adjust the seat backrest only when the vehicle is stationary.
■
When moving the seat backrest, make sure the seat backrest has been
properly secured – check by pulling on the seat backrest.
■
If the seat backrest is folded, passengers may only be transported on the
outer seat behind the driver.
■
When moving the seat backrest, keep limbs out of the area between the
seat and seat backrest – risk of injury!
■
Never transport the following items on the seat backrest when folded
forwards. ■ Objects that could restrict the driver's view.
■ Objects which make it impossible for the driver to control the vehicle,
e.g. if they roll under the pedals, or could protrude into the driver's zone.
■ Objects which could lead to injury to passengers due to a change of di-
rection or braking manoeuvre when accelerating sharply.
Head restraints
 Introduction
This chapter contains information on the following subjects:
Adjusting, installing and removing the headrests.
82
Rear centre head restraints
83
The head restraints and the front seats must be adjusted to match the body
size at all times and the seat belt must always be fastened properly to provide
the most effective levels of protection to the passengers » page 9, Correct and
safe seated position .
Best protection is achieved if the top edge of the head rest is at the same level
as the upper part of your head.
WARNING■ With seats occupied, the respective head rests must be correctly set (may
not be in the bottom position) - risk of fatal injury!■
With seats occupied, the respective head rests must be installed and ad-
justed correctly - risk of fatal injury!
NoteThe position of the front and rear outer head restraints is adjustable in height.
The middle rear head restraint is only adjustable in two positions.
Adjusting, installing and removing the headrests.
Fig. 65
Head restraint: Move up / move down
Read and observe
on page 82 first.
Setting the height
›
Grasp the restraint and move upwards in the direction of
1
» Fig. 65 .
›
To move the restraint down, press the securing button
A
in the direction of
arrow
2
and hold while at the same time pressing the restraint in the direc-
tion of arrow
3
.
Removing/installing
›
Pull the head restraint out of the seat backrest as far as the stop.
›
Press the locking button
A
in the direction of the arrow
2
» Fig. 65 and pull
the head restraint out.
›
To re-insert the head restraint, push it far enough down into the seat back-
rest until the locking button clicks into place.
82Using the system

WARNING (Continued)■Under certain circumstances, air at a temperature of about 5 °C can flow
out of the vents when the cooling system is switched on.■
To reduce health risks (e.g. common colds), the following instructions for
the use of the cooling system are to be observed. ■The difference between the indoor temperature and the outdoor air
temperature should not be greater than about 5 ° C.
■ The cooling system is to be turned off about 10 minutes before the end
of the journey.
■ Once a year, a disinfection of the air conditioner or the Climatronic is to
be carried out by a specialist company.
CAUTION
■ The air inlet in front of the windscreen must be free of e.g. ice, snow or
leaves to ensure that the heating and cooling system operates properly.■
After switching on the cooling Condensation from the evaporator of the air
conditioning may drip down and form a puddle below the vehicle. This is not a
leak!
■
If the coolant temperature is too high, the cooling system is switched off to
ensure that the engine cools down.
Note
The used air streams out through the vents in the luggage compartment.
Air outlet vents
Fig. 109
Air vents at the front
Fig. 110
Air vents at the rear
Read and observe
and on page 104 first.
Warmed, not warmed fresh or cooled air will flow out of the opened air outlet vents according to the setting of the control dial and the outside atmospheric
conditions.
The direction of airflow can be adjusted using the air outlet vents 3,
4 » Fig. 109 and 6 » Fig. 110 - the outlets can be opened and closed individually.
Open the air outlet vents 3 and 4
›
Turn the knob
B
to the position 
» Fig. 109 .
Close air outlet vents 3 and 4
›
Turn the knob
B
to the 0 » Fig. 109 .
Open the air outlet vents 6
›
Turn the knob
C
between the end positions » Fig. 110.
Close air outlet vents 6
›
Turn the knob
C
to the end position » Fig. 110.
Change air flow of air outlet vents 3 and 4
›
To change the height of the air flow, swivel the horizontal fins with the mov-
able adjuster
A
upward or downward » Fig. 109.
›
To adjust the lateral direction of the air flow, turn the vertical fins with the
movable adjuster
A
to the left or to the right.
Change air flow of air outlet vents 6
›
To change the height of the air flow, swivel the horizontal fins with the mov-
able adjuster
A
upward or downward » Fig. 110.
›
To adjust the lateral direction of the air flow, turn the vertical fins with the
movable adjuster
A
to the left or to the right. 
105Heating and air conditioning

If the trailer that is to be towed has a 7-pin connector, you can use a suitable
adapter from ŠKODA Original Accessories to establish a connection to the elec-
tricity.›
Hook the breakaway cable of the trailer onto the safety eyelet
B
.
The breakaway cable of the trailer has to sag when mounted into the security
lock slot for all trailer positions relative to the vehicle (sharp curves, reverse
driving and the like.)
Uncoupling
›
Unhook the breakaway cable of the trailer from the safety eyelet
B
» Fig. 156 .
›
Unplug the trailer cable from the 13-pin socket.
›
Remove the trailer from the ball head.
›
Place the cap
5
» Fig. 147 on page 159 onto the ball head.
›
Grip the 13-pin socket at point
A
and swing in the opposite direction to the
arrow » Fig. 156 .
Exterior mirrors
You have to have additional exterior mirrors fitted if you are not able to see
the traffic behind the trailer with the standard rear-view mirrors. The national
legal requirements must be observed.
Headlights
The front of the vehicle may lift up when a trailer is being towed and the head-
lights may dazzle other road users.
Adjust the headlights using the headlight beam control » page 64,
 Lights
and visibility 1)
.
WARNING■ Incorrect or improperly connected electrical installation can cause acci-
dents and serious injury due to electric shock.■
Work on the electrical system must only be carried out by specialist ga-
rages.
■
Never directly connect the trailer's electrical system with the electrical
connections for the tail lights or other current sources.
■
After coupling the trailer and connecting up the power socket, check the
rear lights on the trailer to ensure they are working.
WARNING (Continued)■ The handbrake on the towing vehicle must be applied when coupling and
uncoupling the trailer.■
Never use the safety eyelet for towing!
CAUTION
Incorrect or improperly connected electrical installations may cause malfunc-
tion of the entire vehicle electronics.
Loading a trailer
The vehicle/trailer combination must be balanced, whereby the maximum per-
missible drawbar load must be utilised. If the drawbar load is too low, it jeop-
ardises the performance of the vehicle/trailer combination.
Distribution of the load
Distribute the load in the trailer in such a way that heavy items are located as
close to the axle as possible. Secure the items from slipping.
The distribution of the weight is very poor if your vehicle is unladen and the
trailer is laden. Maintain a particularly low speed if you cannot avoid driving
with this combination.
Tyre pressure
Correct the tyre inflation pressure on your vehicle for a “full load” » page 191.
Towing capacity and trailer weight
The permissible trailer load must not be exceeded under any circumstan-
ces » page 222 , Technical data .
The details given in the vehicle's technical documentation always take prece-
dence over the details in the Owner's Manual.
The trailer loads specified apply only to altitudes up to 1 000 metres above
mean sea level.
The engine output falls as altitude increases, as does the vehicle's climbing
power. Therefore, for every additional 1000 m in height (or part), the maximum
permissible towed weight must be reduced by 10%.
The towed weight is made up of the actual weights of the loaded towing vehi-
cle and the loaded trailer. 
1)
Applies to vehicles with bi-xenon headlights.
164Driving

WARNING■Read and observe the information and warning instructions on the fluid
containers.■
Keep the working fluids in sealed original containers and safe from peo-
ple who are not completely independent, e.g. children.
■
Never spill operating fluids over the hot engine - risk of fire.
■
If you intend to work underneath the vehicle, you must secure the vehicle
from rolling away and support it with suitable supporting blocks; the car
jack is not sufficient – risk of injury!
CAUTION
Always top up using the correct specification of fluids. This may result in major
operating problems and also vehicle damage!
For the sake of the environment
In view of the requirements for the environmentally friendly disposal of fluids and the special tools and knowledge required for such work, we recommend
that fluids be changed by a specialist garage.
Note
■ Please consult a specialist garage for any questions relating to fluids.■Fluids with the proper specifications can be purchased from the ŠKODA Origi-
nal Accessories or from the ŠKODA Genuine Parts ranges.
Opening and closing the bonnet
Fig. 158
Opening the bonnet
Read and observe and on page 180 first.
Open flap
›
Open the front door.
›
Pull the release lever underneath the dash panel in the direction of the ar-
row
1
» Fig. 158 .
Before opening the bonnet, ensure that the arms of the windscreen wipers
are correctly in place against the windscreen, otherwise the paintwork on the
flap could be damaged.
›
Press the release lever in the direction of the arrow
2
and the bonnet is un-
locked.
›
Grasp the bonnet catch and lift in the direction of arrow
3
.
›
Remove the lid prop in the direction of arrow
4
from the holder.
›
Secure the open flap inserting the end of the post into the opening in the di-
rection of arrow
5
.
Close the flap
›
Lift the bonnet.
›
Decouple the bonnet support and press into the holder designed to hold it.
›
Let the bonnet drop into the lock carrier lock from a height of around 20 cm –
do not push it in .
WARNING■
Check that the bonnet is closed properly.■If you notice that the lock is not properly engaged while driving, stop the
vehicle immediately and close the bonnet – risk of accident!■
Make sure that when closing the boot lid, no body parts are crushed -
there is danger of injury!
CAUTION
Never open the bonnet by the locking lever » Fig. 158.181Inspecting and replenishing

225Tyre width in mm50Height/width ratio in %RCode letter for the type of tyre – Radial17Diameter of wheel in inches91Load indexTSpeed symbol
The date of manufacture is stated on the tyre wall (possibly on the inside).
For example, DOT ... 11 14... means, for example, that the tyre was manufac-
tured in the 11th week of 2014.
The marking M+Smeans that the associated tyre is suitable for winter use.
Load index
The load index indicates the maximum permissible load for each individual
tyre.
Load index90919293949597Load
(In kg)600615630650670690730
Speed symbol
The maximum speed symbol indicates the maximum permissible vehicle speed
with fitted tyres in each category.
Speed iconSTUHVWYMaximum speed
(in km/h)180190200210240270300WARNING■ Never exceed the maximum permissible load bearing capacity of moun-
ted tyres.■
Never exceed the maximum permissible speed for the mounted tyres.
CAUTION
The information about load index and speed symbol can be found in the vehi-
cle sales and technical documentation.Yeti with the 1.2 l/77 kW TSI engine.Model variantTyre sizeMinimal
Load indexMinimal Speed iconYeti with a ground
clearance of 155
mm205/50 R1793T205/55 R1691T195/65 R1591T225/45 R1791TYeti with a ground
clearance of 180
mm205/50 R1793T205/55 R1691T215/60 R1695T225/50 R1794T
Other engine variants
Engine variantTyre sizeMinimal
load indexMinimal speed icon
1.4 ltr. / 90 kW TSI
205/50 R1793H205/55 R1691H215/60 R1695H225/50 R1794H1.6 ltr./77 kW TDI CR205/50 R1793T205/55 R1691T
1.8 ltr./112 kW TSI
205/50 R1793H205/55 R1691H215/60 R1695H225/50 R1794H
1.8 ltr./118 kW TSI
205/50 R1793H205/55 R1691H215/60 R1695H225/50 R1794H 194General Maintenance

DimensionsFig. 208
Principle sketch: Vehicle dimensions
Vehicle dimensions for operating weight without driver (in mm)
» Fig. 208SpecificationYetiYeti OutdoorA
Height
Basic dimension16911691Vehicles with the 1.2 l/77 kW TSI engine.Basic dimension16711691Vehicles with raised suspension1691-Vehicles with the 1.6 l/77 kW TSI engine.16711671BFront track15411541CWidth17931793DRear track15371537EWidth including exterior mirror19561956F
Clearance
Basic dimension180180Vehicles with 1.2 l / 77 kW TSI engineBasic dimension155180Vehicles with raised suspension180-Vehicles with 1.6 l / 77 kW TSI CR engine155155GWheel base25782578HLength42224222224Technical data

angle and gradeabilityFig. 209
Principle sketch: Overhang angle and ramp angle / slope angle
Angle » Fig. 209
Overhang angle, front
Ramp angle
Overhang angle, rear
Pitch angle / climbing ability
ABCDOverhang angle
The values shown indicate the maximum incline of an embankment, up which
the vehicle can drive at a slow speed without collision of the bumper or under-
body.
The values listed correspond to the maximum axle load, front or back.
Ramp angle
The angle indication determines the angle at which you can drive the vehicle
over a ramp, at a slow speed, without the under body of the vehicle touching
the ramp edge.
Pitch angle / climbing ability
The specification to which the vehicle can drive up a slope on its own (depend-
ing inter alia on the road surface and engine power).
The height gained over a distance of 100 m (slope) is specified in percent or degrees.Angle and climbing abilityEngineOverhang angle (°)Overhang angle (°)Ramp angle (°)Slope angle (°) / climbing ability (%)1.2 l / 77 kW TSIYeti17.1 / 19a)30 / 32a)17.2 / 19.6 a)24 / 45Yeti Outdoor193219.624 / 451.4 ltr. / 90 kW TSI193219.627 / 501.6 l. / 81 kW MPIMG5193219.622 / 40AG6193219.645 / 1001.8 l/118 (112) kW TSI193219.629 / 551.6 ltr. / 77 kW TDI CR17.13017.229 / 552.0 ltr / 81 kW TDI CRMG5193219.629 / 55MG6 4 x 4193219.631 / 602.0 l / 103 (125) kW TDI CR193219.631 / 602.0 ltr./103 kW TDI CR - Green tec193219.629 / 55a)
Valid for vehicles with raised suspension.
225Technical data

Index
A
abroad lead-free petrol
178
Abroad Headlights
69
ABS Function
143
Warning light38
Acceptance and recycling of used vehicles169
Accessories166
Adaptive headlights (AFS)66
adjusting auxiliary heating and ventilation
111
Adjusting Belt height
15
Exterior mirrors76
Head restraints82
Interior mirror75
seats78
Steering wheel10
the seats electronically78
Adjusting the seats9
Adjusting the seats electronically78
adjustment Front seat
77
Adjustment Headlight beam
64
AFS66
Display messages39
Warning light39
Air-conditioning system Air outlet vents
105
Airbag16
Deactivating21
Deactivating the front passenger airbag22
Deployment17
Front airbag18
Head airbag20
Knee airbag19
Modifications and damage to the airbag system 168
Side airbag
19
Warning light40
Airbag system16
Air conditioning104
Air distribution control106
Climatronic108
manual air conditioning107
Air distribution control106
Air outlet vents105
Alarm Switching off
56
Triggering56
Alcantara cleaning
175
Alternator Warning light
36
Anti-theft alarm system Activating/deactivating
56
Trailer165
Anti-theft wheel bolts203
Antilock Braking System143
Armrest Front
81
artificial leather175
Ashtray89
ASR warning light
37
Assistance systems TSA
144
Assistence systems OFF ROAD-mode
144
Assist system ABS
143
Assist systems142
ABS38
ASR37
Cruise Control System154
DSR144
EDL143
ESC38, 143
HBA144
HHC144
Park assist150
Parking aid146
START-STOP155
TCS143
Audio See Infotainment / radio
4
Auto Check Control33
Automatic driving lamp control66
Automatic gearbox Manual shifting of gears
139
Selector lever-emergency unlocking212
Selector lever lock139
Starting-off and driving140
Tiptronic139
Using the selector lever138
Automatic gearbox modes138
Automatic load deactivation190
automatic transmission selector lever lock defect
139
Automatic transmission138
Kickdown140
Selector lever lock139
Auxiliary heating and ventilation Switching on and off directly
111
System settings111
Auxiliary heating (auxiliary heating and ventila- tion)
110
Radio remote control111
B
Ball head Check fitting
161
Ready position160
231Index