2014 SKODA ROOMSTER bulb

No.Consumer27Telephone preinstallation28Petrol engine: AKF valve, Diesel engine: Control flap29Injection, coolant pump30Fuel pump, ignition, Cruise control system, operation of PTC relay31Lambda probe32High pressure fuel pump, pressure valve33Engine control unit34Engine control unit, vacuum pump35Daytime running lights/radio for vehicles with START-STOP36Main beam37Rear fog light, DC/DC converter START-STOP38Fog lights39Air blower for heating40-41Not assigned42Rear window heater43Horn44Windscreen wipers45Central control unit for convenience system46Engine control unit, fuel pump47Cigarette lighter, power socket in the luggage compartment48ABS, START-STOP (DC/DC) converter, ESC49Turn signal lights, brake lights50START-STOP (DC/DC) transformer, radio51Electrical power window (front and rear) - left side52Electrical power window (front and rear) - right side53Parking light = left side, electrical sliding/tilting roof54START-STOP (instrument cluster), alarm55Control unit for automatic gearbox56Headlight cleaning system, parking light - right side57Left low beam, headlight range adjustment58Low beam on the rightFuses in the engine compartmentFig. 159
Vehicle battery: Distribution board cover.
Fig. 160
Schematic representation of fuse
box in engine compartment
Read and observe and on page 175 first.
› Press the securing clips on the fuse box cover together at the same time in
the direction of arrow
A
» Fig. 159 and remove the cover in the direction of
arrow
B
.
› Release the fixtures in the openings
C
using a flat screwdriver and fold the
cover upwards in direction of arrow
D
.
Fuse assignment in engine compartment
No.Consumer1Generator2Not assigned3Interior4Electrical auxiliary heating system5Interior 177Fuses and light bulbs

No.Consumer6Glow plugs, radiator fan7Electro-hydraulic power steering8ABS or TCS or ESC9Radiator fan10Automatic gearbox11ABS or TCS or ESC12Central control unit13Electrical auxiliary heating system
Note
Fuses 1-7 are replaced by a specialist garage.
Replacing bulbs
Introduction
This chapter contains information on the following subjects:
Headlights
179
Changing the low beam and high beam bulb (halogen headlights)
179
Changing the high beam bulb (halogen projector headlights)
179
Changing the high beam bulb (halogen projector headlights)
180
Changing the front turn signal bulb
180
Changing the front parking light bulb
180
Fog lights and daytime running lights
180
Fog light, Roomster Scout
181
Replacing the bulb for the licence plate light
181
Rear Light
181
Some manual skills are required to change a bulb. For this reason, we recom-
mend having bulbs replaced by a specialist garage or seeking other expert help
in the event of any uncertainties.
› Switch off the ignition and all of the lights before replacing a bulb.
› Faulty bulbs must only be replaced with the same type of bulbs. The designa-
tion is located on the light socket or the glass bulb.
› A stowage compartment for replacement bulbs is located in a plastic box in
the spare wheel or underneath the floor covering in the boot.
WARNING■ Always read and observe the warnings before completing any work in the
engine compartment » page 145.■
Accidents can be caused if the road in front of the vehicle is not suffi-
ciently illuminated and the vehicle cannot or can only be seen with difficul-
ty by other road users.
■
Bulbs H7 and H4 are pressurised and may burst when changed - there is a
risk of injury. We therefore recommended wearing gloves and safety
glasses when changing a bulb.
■
Switch off the respective vehicle light when changing the bulb.
CAUTION
■ Do not take hold of the glass bulb with naked fingers (even the smallest
amount of dirt reduces the working life of the light bulb). Use a clean cloth,
napkin, or similar.■
When removing and installing the number plate light and tail light make sure
that the paintwork of the vehicle and the tail light are not damaged.
Note
■ This Owner's Manual only describes the replacement of bulbs where it is pos-
sible to replace the bulbs on your own without any complications arising. Other
bulbs must be replaced by a specialist garage.■
We recommend that a box of replacement bulbs always be carried in the ve-
hicle. Replacement bulbs can be purchased from ŠKODAOriginal Accessories.
■
We recommend having the headlight settings checked by a specialist garage
after replacing a bulb in the main beam, low beam or fog lights.
■
Visit a specialist garage if an LED is faulty.
178Do-it-yourself

HeadlightsFig. 161
Bulb arrangement: Halogen headlights/halogen projector head-
lights
Read and observe
and on page 178 first.
Bulb arrangement in the Halogen headlamp
A
- low beam, main beam and side lights
B
- front turn signal light
Bulb arrangement in the Halogen projector headlights
1
- low beam / low and main beam
2
- parking light / parking and main beam lights
3
- turn signal lights
Changing the low beam and high beam bulb (halogen headlights)
Fig. 162
Removing bulbs for low and
main beam
Read and observe and on page 178 first.
›
Remove the protective cap
A
» Fig. 161 on page 179 .
›Remove the connector from the bulb, unlock the securing clip and remove
the bulb in the direction of the arrow » Fig. 162.›
Insert a new light bulb in such a way that the fixing lugs of the bulb socket fit
in the recesses of the reflector.
›
Lock the circlip and insert the connector in the bulb.
›
Fit the protective cap
A
.
Changing the high beam bulb (halogen projector headlights)
Fig. 163
Removing the bulb for the low
beam
Read and observe and on page 178 first.
›
Remove the protective cap
1
» Fig. 161 on page 179 .
›
Turn the socket with the bulb to the stop in the direction of the ar-
row » Fig. 163 and remove it.
›
Replace the bulb, insert the connector and new bulb and turn to the stop in
the opposite direction to that of the arrow.
›
Fit the protective cover
1
.
179Fuses and light bulbs

Changing the high beam bulb (halogen projector headlights)Fig. 164
Removing the bulb for the main
beam
Read and observe and on page 178 first.
›
Remove the protective cap
2
» Fig. 161 on page 179 .
›
Turn the socket with the bulb to the stop in the direction of the ar-
row » Fig. 164 and remove it.
›
Replace the bulb, insert the connector and new bulb and turn to the stop in
the opposite direction to that of the arrow.
›
Fit the protective cover
2
.
Changing the front turn signal bulb
Read and observe
and on page 178 first.
›
Remove the bulb holder
B
» Fig. 161 on page 179 or the bulb holder
3
to the
stop in an anti-clockwise direction and remove with the bulb for the turn sig-
nal.
›
Replace the bulb, insert the bulb holder with the new bulb and turn clock-
wise to the stop.
Changing the front parking light bulb
Read and observe
and on page 178 first.
›
Remove the protective cap
A
» Fig. 161 on page 179 or
2
.
›
Grasp the lamp holder and remove it from the bulb housing.
›
Replace the light bulb and insert the lamp holder back into the headlamp
with the bulb.
›
Fit the protective cap.
Fog lights and daytime running lightsFig. 165
Front bumper: Protective grille/removing the fog light
Read and observe
and on page 178 first.
Bulb arrangement » Fig. 165
Light bulb for daytime driving light
Light bulb for fog lights
Removing the cap
›
Grasp the protective grille in the areas marked by the arrows » Fig. 165 -

and remove the cover in the direction of the arrow.
Replacing light bulbs for fog lights/daytime running lights
›
Insert your hand into the opening in the protective grille and press the
catch » Fig. 165 -
 in the direction of the arrow.
›
Remove the fog lamp.
›
Turn the connector with the bulb in
counter-clockwise up to the stop and re-
move.
›
Replace the bulb, insert the holder with the new bulb and turn clockwise to
the stop.
›
To re-install the fog light, first of all place the fog light with the lug on the
side opposite the licence plate.
›
Press in the fog lamp on the side closest to the licence plate.
›
Insert the cap, beginning with the lug on the side opposite the license plate.
›
Press in the cap on the side facing the license plate. The cap must engage
firmly.
AB180Do-it-yourself

Fog light, Roomster ScoutFig. 166
Front bumper: Roomster Scout
Fig. 167
Front bumper: Fog lights/fog lights: Replacing the light bulb
Read and observe
and on page 178 first.
Removing the cap and fog light
›
Insert the tool » page 166, Vehicle tool kit into the opening above the fog
light » Fig. 166 and remove the cover.
›
Unscrew the screws » Fig. 167 -
 with the screwdriver
» page 166, Vehicle
tool kit .
›
Remove the fog lamp.
Changing light bulbs and installing fog lights
›
Press the locking tab
1
» Fig. 167 on the connector
A
and remove the con-
nector from the bulb holder
B
.
›
Turn the bulb holder
B
and bulb in the direction of the arrow to the stop and
remove.
›
Replace the bulb, insert the bulb holder and new bulb and turn in the oppo-
site direction to that of the arrow to the stop.
›
Insert the plug
A
into the socket
B
.
› Retighten the screws and insert the cap. The cap must engage firmly.
Replacing the bulb for the licence plate light
Fig. 168
Remove the licence plate light
Read and observe and on page 178 first.
›
Open the tailgate and unscrew the glass cover
» Fig. 168.
›
Remove the faulty bulb from the holder and insert a new one.
›
Replace the glass cover and push in until the stop. Make sure that you install
the rubber seal in the right direction.
›
Slightly screw the glass cover.
Rear Light
Fig. 169
Removing the tail light assembly/disconnecting the plug connec-
tion 
181Fuses and light bulbs

Fig. 170
Remove the middle part of the light/bulb arrangement
Read and observe
and on page 178 first.
Bulb arrangement in the tail light » Fig. 170
Brake light
Flashing
Reversing light
The rear fog light
Parking lights
Removing and installing the tail light
›
Open the tailgate.
›
Unscrew the light assembly » Fig. 169 -
 .
›
Grip the light in the upper and lower area and move backwards somewhat.
›
Unplug the connector
» Fig. 169 -
 .
›
To access the bulbs, unscrew the middle of the light assembly and press off
the tabs » Fig. 170 -
 .
›
To reinstall, screw the middle part of the light onto the housing of the rail
light.
›
Reconnect the plug connection and put the light into the original position.
›
Screw the light into place
Replacing the bulbs in the tail lamp assembly
›
Remove the faulty bulb
1
,
2
,
3
or
4
» Fig. 170 from the holder and fit a
new bulb.
›
To replace the bulb, turn the bulb holder
5
anti-clockwise up to the stop
and remove it from the housing.
›
Replace the bulb, insert the holder with the bulb into the housing and turn in
a clockwise direction to the the stop.
12345182Do-it-yourself

Central locking system49
lock51
unlock51
Changing brake fluid
152
bulbs178
Changing the bulb for fog light (Scout)181
Fog lights and daytime running lights bulbs180
Front parking light bulb180
Front turn signal bulb180
High beam bulb - halogen projector headlights 179, 180
light bulb in tail light
181
Low beam and high beam bulb - halogen head- lights
179
Wheels166
Changing a wheel Follow-up work
167
Preliminary work167
Remove and attaching a wheel167
Changing brake fluid
152
Charging a vehicle battery155
Check Fit ball head properly
128
Checking Battery electrolyte level
154
Brake fluid152
Coolant151
Engine oil149
Oil level149
Windscreen washer fluid147
Checks Statutory checks
132
Children and safety22
Child safety Side airbag
24
Child safety lock48
Child seat Classification
24
ISOFIX25
on the front passenger seat23
TOP TETHER26
Use of child seats24
Use of ISOFIX child seats25
Chrome parts refer to Taking care of your vehicle
137
Cigarette lighter82
Cleaning Alcantara
141
Covers of electrically heated seats141
Fabrics141
Headlight lenses138
Natural leather140
Plastic parts137
Synthetic leather141
Wheels139
Cleaning vehicle135
Climatronic95
automatic mode96
Control elements95
Controlling blower96
Defrosting windscreen97
Recirculated air mode96
Setting the temperature96
Clock32
Clothes hook83
Cockpit 12-volt power outlet
82
Ashtray81
Cigarette lighter82
General view29
Lighting63
Storage compartments83
Compartments83
Components of the puncture repair kits170
Computer see Multifunction display
33
Convenience turn signal61
Coolant150
Checking151
Display messages41
Replenishing151
Warning light41
Coolant temperature gauge display
31
Correct seated position9
Driver9
Front passenger10
Instructions11
Rear seats11
Counter for distance driven32
Cruise Control System121
Cupholders81
D
DAY LIGHT see Daylight running lights
60
Daylight running lights60
Deactivating an airbag20
Decorative films137
Defrosting rear window64
Delayed locking of the boot lid see boot lid
55
Diesel refer to Fuel
144
Diesel fuel Operation in winter
144
Diesel particulate filter43
display messages43
Digital clock32
Dimmed headlights59
Dipstick149
Display Service interval
36
Distance driven32
191Index

Glow plug systemWarning light43
GSM97
H
Handbrake
109
Hazard warning light system63
Head airbag19
Headlight cleaning system Headlight cleaning system
67
Headlights179
Driving abroad118
Headlight cleaning system67
Headrest Headrest
73
Head restraint72
Heating Deicing the windows
92
Exterior mirrors68
Operating91
Operation91
Rear window64
Recirculated air mode92
Seats69
Heating and air-conditioning90
Hill hold control119
Hitch126
Accessories129
Drawback load126
Horn29
I
Ignition
107
Ignition lock107
Immobilizer107
Individual settings locking
50
unlocking50
Inertia reels15
Instrument cluster30
Overview30
see instrument cluster30
Interior monitor54
Internal lighting Praktik
89
Internal lights Praktik
89
ISOFIX25
J
Jack
166
Maintenance138
Jump-starting172
L
lashings Praktik
88
Light Cockpit
63
Dimmed headlights59
Headlight beam adjustment60
Headlight flash61
Sidelights59
Lights59
Cockpit63, 64
Daylight running60
Fog lights61
Foglights with the CORNER function62
Halogen projector headlights with cornering light function
61
Hazard warning light system63
Main beam lights61
Parking lights63
Rear fog light62
Replacing bulbs178
Tourist lights62
Turn signals61
warning lights39
Lock Central locking system51
Locking Emergency locking
49
Remote control52
without central locking49
Locking and unlocking from the inside51
Low tyre pressure warning refer to the tyre pressure monitoring
125
Luggage compartment Class N1 vehicles
74
Lighting64
Variable loading floor76
Luggage compartment lid54
M
Main beam
61
Maintenance116
Decorative films137
Manual air conditioning Recirculated air mode
94
Manual gear changing see gear changing
109
MAXI DOT Main menu
37
see MAXI DOT display37
Settings38
MAXI DOT display37
Maximum permissible weights
183
Maximum speed186
MDI104
Mechanical windows58
open and close58
Media see radio / navigation system
4
193Index