2014 SKODA RAPID warning

CAUTIONIf in addition to the warning light  the warning light  » page 36 lights up
while driving,  stop driving - there is a risk of engine damage! Switch off the
engine and seek assistance from a specialist garage.
 Door open
Read and observe
on page 35 first.
The indicator light 
illuminates if one or several doors or luggage compart-
ment lid are opened.
  Engine oil
Read and observe
on page 35 first.
The warning light  flashes (low oil pressure)
The following message is shown in the MAXI DOT display.
Oil pressure: Engine off! Owner's manual!
› Stop the vehicle, switch off the engine, and check the engine oil lev-
el » page 141 .
› If the oil pressure is too low, top up the engine oil
» page 142.
If the oil level is within the specified range and the warning light flashes
 again after the engine is started,
do not continue driving!
Switch off the engine and seek assistance from a specialist garage.
The indicator light  lights up (oil quantity too low)
The following message is shown in the MAXI DOT display.
Check oil level!
› Stop the vehicle, switch off the engine, and check the engine oil lev-
el » page 141 .
The warning light will go out if the bonnet is left open for more than 30 sec-
onds . If no engine oil has been replenished, the warning light will
come on
again after driving about 100 km.
The indicator light  flashes (engine oil level sensor faulty)
The following message is shown in the MAXI DOT display.
Oil sensor: Workshop!
If the engine oil level sensor is faulty, the warning light  flashes several
times and an audible signal sounds when the ignition is turned on.
Seek assistance from a specialist garage immediately.
CAUTION
 Stop driving if for some reason it is not possible to top up the engine oil un-
der the current conditions. Switch off the engine and seek assistance from a
specialist garage.
  Coolant
Read and observe
on page 35 first.
The  indicator light remains
illuminated until the engine reaches operating
temperature 1)
. Avoid high speeds, full throttle and high engine loads.
If the warning light 
lights up or flashes , either the coolant temperature is
too high or the coolant level is too low.
The following message is shown in the MAXI DOT display. Check coolant! Owner's manual!
›
Stop the vehicle, switch off the engine and check the coolant lev-
el » page 143 .
›
If the coolant level is too low, add coolant to the reservoir » page 143.
If the indicator light 
does not illuminate after adding coolant and switching
on the ignition, you may continue your journey.
If the coolant is within the specified range and the warning light  is still
lit
after switching on the ignition, then there may be a malfunction of the cooling
fan.
›
Switch off the ignition.
›
Check the fuse for the radiator fan, replace if necessary » page 171, Fuses in
the engine compartment .
If the coolant level and fan fuse are OK and the warning light 
lights up again
after switching on the ignition, do not continue driving!
Seek help from a specialist garage. 
1)
Applies to cars with the instrument cluster - Version 2.
36Using the system

WARNING■Carefully open the coolant expansion bottle. If the engine is hot, the cool-
ing system is pressurized – risk of scalding! It is therefore best to allow the
engine to cool down before removing the cap.■
Do not touch the radiator fan. The radiator fan may switch itself on auto-
matically even if the ignition is off - a danger of injury is present!
CAUTION
■ Additional headlights and other attached components in front of the air inlet
impair the cooling efficiency of the coolant.■
Never cover the radiator - there is a risk of the engine overheating.
 Power steering
Read and observe
on page 35 first.
If the indicator light 
is illuminated , there is a fault in the power steering sys-
tem.
The power steering operates with reduced steering assist or does not function
at all.
Seek assistance from a specialist garage immediately.
 Electronic Stability Control (ESC)
Read and observe
on page 35 first.
The warning light 
flashes to show that the ESC is currently operating.
If the warning light 
illuminates , there is a fault in the ESC.
The following message is shown in the MAXI DOT display. Error: stabilization control (ESC)
or Error: Traction control (TCS)
Seek assistance from a specialist garage immediately.
If the warning light 
illuminates immediately after you start the engine, the
ESC might be switched off due to technical reasons.
›
Switch the ignition off and on again.
If the warning light  does not illuminate after you switch the engine back on,
the ESR is fully functional again.
Further information » page 109, Electronic Stability Control (ESC) .
Note
If the vehicle battery has been disconnected and then reconnected, the warn-
ing light  comes on after switching on the ignition. If the warning light does
not go out after moving a short distance, this means that there is an error in
the system. Seek assistance from a specialist garage immediately.
 Traction Control System (ASR)
Read and observe
on page 35 first.
The warning light flashes
 to show that the ASR is currently operating.
If the warning light 
illuminates , there is a fault in the ASR.
The following message is shown in the MAXI DOT display. Error: Traction control (TCS)
Seek assistance from a specialist garage immediately.
If the warning light 
illuminates immediately after you start the engine, the
ASR might be switched off due to technical reasons.
›
Switch the ignition off and on again.
The ASR is fully functional again if the  warning light
no longer illuminates
after you switch the engine back on.
Further information » page 109, Traction Control System (TCS) .
Note
If the vehicle battery has been disconnected and then reconnected, the warn-
ing light  comes on after switching on the ignition. If the warning light does
not go out after moving a short distance, this means that there is an error in
the system. Seek assistance from a specialist garage immediately.
Antilock brake system (ABS)
Read and observe
on page 35 first.
If the warning light 
illuminates , there is a fault in the ABS. 
37Instruments and Indicator Lights

The following message is shown in the MAXI DOT display.Error: ABS
The vehicle will only be braked by the normal brake system without the ABS.
Seek assistance from a specialist garage immediately.
In the event of an ABS fault, the other braking and stabilization systems are
turned off » page 109 , Braking and stabilisation systems .WARNING■
A fault to the ABS system or the braking system can increase the vehi-
cle's braking distance – risk of accident!■
If the warning light 
together with the warning light 
» page 35 , 
Brake system illuminates, 
do not continue to drive! Seek help from a
specialist garage.
 Rear fog light
Read and observe
on page 35 first.
The warning light 
illuminates when the rear fog light is switched on.
 Lamp failure
Read and observe
on page 35 first.
The warning light 
illuminates if a lamp is faulty or if an external vehicle lamp
is faulty .
The indicator light 
illuminates within a few seconds after switching on the
ignition or when a light with a faulty lamp is switched on .
The following message, for example, may be shown in the MAXI DOT display. INFORMATION Check front right low beam!
The rear side lights and the licence plate lighting have several light bulbs. The indicator light  only lights up if all bulbs in the parking light (in one rear light)
or the licence plate lighting are faulty 1)
. For this reason, regular check that
these light bulbs are working correctly.
 Exhaust inspection system
Read and observe
on page 35 first.
If the warning light 
illuminates , there is a fault in the exhaust inspection
system. The system allows the vehicle to run in emergency mode.
Seek assistance from a specialist garage immediately.
 Glow plug system (diesel engine)
Read and observe
on page 35 first.
The warning light 
illuminates after the ignition has been switched on. Once
the light has gone out, the engine can be started immediately.
There is a fault in the glow plug system if the warning light 
does not come
on at all or lights up continuously .
If the warning light  begins to
flash while driving, a fault exists in the engine
control. The system allows the vehicle to run in emergency mode.
Seek assistance from a specialist garage immediately.
 Engine performance check (petrol engine)
Read and observe
on page 35 first.
If the indicator light 
illuminates , there is a fault in the engine control. The
system allows the vehicle to run in emergency mode.
Seek assistance from a specialist garage immediately.
 Diesel particulate filter (Diesel motor)
Read and observe
on page 35 first.
The diesel particulate filter separates the soot particles from the exhaust. The soot particles collect in the diesel particulate filter where they are burnt on a
regular basis.
If the indicator light 
illuminates , soot has accumulated in the filter. 
1)
Applies to vehicles with START-STOP system.
38Using the system

To clean the filter, and where traffic conditions permit » , drive as follows for
at least 15 minutes or until the indicator light  goes out.
4th or 5th gear selected (automatic transmission: position S).
Vehicle speed at least 70 km/h.
Engine speed between 1800-2500 rpm.
If the filter is properly cleaned, the warning icon 
goes out .
If the filter is not properly cleaned, the warning light 
does not go out and
the warning light 
begins to flash.
The following message is shown in the MAXI DOT display. Diesel particulate filter: Owner's manual!
The system allows the vehicle to run in emergency mode. After switching the
ignition off and on again the indicator light, the indicator light  also
illumi-
nates .
Seek assistance from a specialist garage immediately.WARNING■ The diesel particulate filter reaches very high temperatures - there is a
fire hazard and serious injury could be caused. Therefore, never stop the
vehicle at places where the underside of your vehicle can come into contact
with flammable materials such as dry grass, undergrowth, leaves, spilled
fuel or such like.■
Always adjust your speed to suit weather, road, region and traffic condi-
tions. The recommendations indicated by the warning light must not tempt
you to disregard the national regulations for road traffic.
CAUTION
■ As long as the warning light  lights up, one must take into account an in-
creased fuel consumption and in certain circumstances a power reduction of
the engine.■
Using diesel fuel with increased sulphur content can significantly reduce the
service life of the diesel particle filter. A ŠKODA Partner will be able to tell you
which countries use diesel fuel with increased sulphur content.
Note
■ To assist the combustion process of the soot particles in the filter, we recom-
mend that regularly driving short distances be avoided.■
If the engine is turned off during the filter cleaning process or shortly after-
wards, the cooling fan may turn on automatically for a few minutes.
 Fuel reserve
Read and observe
on page 35 first.
When the warning light 
is illuminated , this means there is a fuel reserve of
under around 7 litres left.
The following message is shown in the MAXI DOT display.
Please refuel. Range: ... km
CAUTION
Never drive until the fuel tank is completely empty! The irregular supply of fuel
can cause misfiring. This can result in considerable damage to parts of the en-
gine and the exhaust system.
Note
The text in the display goes out only after refuelling and driving a short dis-
tance.
 Airbag system
Read and observe
on page 35 first.
If the warning light 
illuminates , there is a fault in the airbag system.
The following message is shown in the MAXI DOT display. Error: Airbag
The functionality of the airbag system is monitored automatically even if one
of the airbags is switched off.
The front passenger airbag has been disabled with the key switch
› The indicator light

illuminates for around 4 seconds after the ignition has
been switched on;
› The warning light


in the display 




in the middle of the
dash panel lights up after switching on the ignition » Fig. 12 on page 20 .
One of the airbags or a belt tensioner has been disabled by the diagnostic
tool
› The warning light

illuminates for approx. 4 seconds after switching on the
ignition and then flashes again for approx. 12 seconds afterwards.
The following message is shown in the MAXI DOT display. Airbag / belt tensioner deactivated. 
39Instruments and Indicator Lights

WARNINGWhen a fault in the airbag system occurs, there is a risk of the system not
being triggered in the event of an accident. Therefore, this must be
checked immediately by a specialized company.
 Tyre inflation pressure
Read and observe
on page 35 first.
The warning light  is illuminated
If the warning light  illuminates while driving, it means one of the tyres has
undergone a pressure change.
An audible signal sounds as a warning signal.
›
Immediately reduce speed and avoid sudden steering and braking manoeu-
vres.
›
Stop the vehicle, turn the ignition off and check the tyres and their inflation
pressure » page 149 .
›
Correct the tyre pressure, if necessary or replace the affected
wheel » page 156 or use the repair kit » page 160.
›
Store the tyre pressure values in the system » page 115.
The indicator light  flashes for about 1 min. and remains lit
If the warning light  flashes for approximately 1 minute and stays on, there
may be a fault in the tyre pressure monitoring system.
›
Stop the vehicle, turn the ignition off and start the engine again.
If the warning light  flashes again after the engine has started, there is a
system error.
Seek help from a specialist garage.
The following reasons can explain the warning light  being illuminated.
› The vehicle is loaded on one side. Distribute loads as evenly as possible.
› The wheels of one axle are loaded more heavily (e.g. when towing a trailer or
when driving uphill or downhill).
› Snow chains are mounted.
› A wheel has been changed.
Store the tyre pressure values in the system » page 115.
CAUTIONUnder certain circumstances (e.g. sporty style of driving, wintry or unpaved
roads) the warning light  in the instrument cluster can be delayed or does
not light up at all.
Note
If the vehicle battery has been disconnected and then reconnected, the warn-
ing light  comes on after switching on the ignition. If the warning light does
not go out after moving a short distance, this means that there is an error in
the system. Seek help from a specialist garage.
 Windscreen washer fluid level
Read and observe
on page 35 first.
If the windscreen washer fluid level is too low, the warning light 
illumi-
nates .
The following message is shown in the MAXI DOT display. Top up wash fluid!
Top up with liquid » page 139, Windscreen washer system .
  Turn signal system
Read and observe
on page 35 first.
Either the left 
or the right 
warning light flashes depending on the position
of the turn signal lever.
If there is a fault in the turn signal system, the warning light flashes at twice
its normal rate.
Switching off the hazard warning light system is switched on will cause all of
the turn signal lights as well as both warning lights to flash.
 Fog lights
Read and observe
on page 35 first.
The warning light 
illuminates when the fog lights are operating.
40Using the system

 Cruise control systemRead and observe
on page 35 first.
The warning light 
illuminates when the cruise control is active » page 111.
 Brake pedal (automatic gearbox)
Read and observe
on page 35 first.
If the warning light 
illuminates , operate the brake pedal.
 Main beam
Read and observe
on page 35 first.
The warning light 
illuminates when the main beam or the headlight flasher
is operated.
Information system
Driver information system
 Introduction
This chapter contains information on the following subjects:
Using the information system
42
Display a low temperature
42
Gear recommendation
43
Door, boot or engine compartment warning
43
The information system provides the driver with alerts and messages about in-
dividual vehicle systems.
This information and advice is shown in the instrument cluster display or indi-
cated by the illumination of the corresponding indicator light in the instrument
cluster.
The information system provides the following information and instructions
(depending on vehicle equipment).
› Data relating to the multi-function display (MFD)
» page 43.
› Data relating to the MAXI DOT display
» page 46.
› Service interval display
» page 47.
› Auto Check Control
» page 33.
› Selector lever positions for an automatic gearbox
» page 105.
WARNINGConcentrate fully on your driving at all times! As the driver, you are fully re-
sponsible for the operation of your vehicle.41Information system

Using the information systemFig. 26
Buttons/wheel: on the operating lever or the multifunction steer-
ing wheel
Read and observe
on page 41 first.
Some functions of the information system can be operated using the buttons
on the multifunction steering wheel » Fig. 26.
Description of the operation
Button/ wheelActionOperationABriefly press at the top or below for a longer timeSelect data / set data valuesPress top
or below for a longer timeDisplay main menu of the
MAXI DOT display » page 46BPress brieflyView information / confirm specificationCPress brieflyTo go up one level in the menu of the
MAXI DOT display » page 46Press and hold buttonDisplay main menu of the
MAXI DOT display » page 46DTurn upwards or down-
wardsSelect data / set data valuesPress brieflyView information / confirm specificationDisplay a low temperature
Read and observe
on page 41 first.
Prompt in the MAXI DOT display
If the outside temperature while driving drops to below +4°C, the following
icon appears on the display in front of the temperature display 
. An audible
signal is emitted.
If the outside temperature is already below +4°C when turning the ignition on,
the 
icon appears immediately.
Prompt in the segment display 1)
If the outside temperature while driving drops to below +4°C, the temperature
display » page 45 , Outside temperature will show up with the following icon
in front . An audible signal is emitted.
If the outside temperature is already below +4°C when turning the ignition on, the temperature display and the  icon appear immediately.
After pressing button
A
» Fig. 26 on page 42 , the most recently displayed da-
ta is shown.
WARNINGEven at outside temperatures of around +4 °C, black ice may still be present
on the road surface! You should therefore not rely solely on the outside
temperature display for an indication of whether there is black ice on the
road.1)
Applies to vehicles with the multifunction display (MFA).
42Using the system

Gear recommendationFig. 27
Information on the selected
gear / Gear recommendation
Read and observe on page 41 first.
The function of the gear recommendation is to help reduce fuel consumption.
A suitable gear is engaged, if necessary, a recommendation to shift to high or
lower gear is displayed.
Display » Fig. 27
Optimal gear engaged
Recommended gear
Recommended gear
The gear recommendation is intended only for vehicles with a manual trans- mission or for vehicles with an automatic transmission in manual shift mode
(Tiptronic).
The recommended 1)
gear and the arrow icon 2)
is displayed.
› 
- Recommends that you shift to a
higher gear
› 
- Recommends that you shift to a
lower gear
If for example  is shown in the display with vehicles that have
manual gear-
boxes this indicates that it is better to shift from a lower gear to the 4th gear.
If for example  is shown in the display with vehicles that have
automatic
gearboxes and are in the manual switching mode (Tiptronic), this indicates
that it is better to shift from the 4th gear to a higher gear.
WARNINGThe driver is always responsible for selecting the correct gear in different
driving situations, such as overtaking.
For the sake of the environment
A suitably selected gear has the following advantages.■It helps to reduce fuel consumption.■
It reduces the operating noise.
■
It protects the environment.
■
It benefits the durability and reliability of the engine.
Door, boot or engine compartment warning
Read and observe
on page 41 first.
Vehicles with a MAXI DOT display
If at least one door, the boot or bonnet is open, the display indicates the rele-
vant open door, boot or bonnet vehicle icon.
Vehicles with a segment display
If at least one door or the tailgate is open, the 
warning light in the instru-
ment cluster lights up » page 36.
An acoustic signal will also sound if you drive the vehicle above 6 km/h when a door is open.
Multifunction display (MFD)
 Introduction
This chapter contains information on the following subjects:
Memory
44
Information overview
45
Warning at excessive speeds
46
The driving data is displayed on the multifunction display. 
1)
With vehicles that have an automatic gearbox and in the manual switching mode (Tiptronic) the
current-
ly engaged gear is shown.
2)
For vehicles with segment display the arrow is displayed behind the gear indication.
43Information system