2014 SKODA FABIA low beam

Downloaded from www.Manualslib.com manuals search engine Reducing idling
If the vehicle is fitted with the START - STOP system there is an automatic re-
duction of the idling. If the engine is stopped on vehicles without START-STOP
system, such as when waiting in a traffic jam, the fuel economy is already
greater after 30 - 40 s than the fuel quantity which is required for engine re-
start.
Avoid short distances
When driving a short distance of less than about 4 km, the engine cannot
reach its operating temperature. As long as the engine has not reached oper-
ating temperature, the fuel consumption is significantly higher than with the
engine hot.
Pay attention to the correct tyre inflation pressure being maintained
Further information » page 161.
Avoid unnecessary ballast
Per 100 kg of weight, consumption increases by about 0.3 l/100 km. At a speed of 100 - 120 km/h, a vehicle fitted with a roof rack cross member without a load
will use about 10 % more fuel than normal due to the increased aerodynamic
drag.
Saving electricity
Electrical consumers (e.g. seat heating, air conditioning and the like) should
only be turned on for as long as necessary.
Use the cooling system economically
The air conditioning system compressor uses power from the engine when in
cooling mode, which will affect the fuel consumption.
It recommended to open the windows or the doors of a vehicle for which the
interior has been strongly heated through the effect of direct sunlight in order
to allow the heated air to escape.
The cooling system should not be switched on if the windows are open.DriveGreen functionFig. 121
Shown in the infotainment dis-
play
The DriveGreen function (hereinafter referred to only as DriveGreen) evaluates
the driving efficiency based on the information respecting the driving style.
Useful tips for reducing fuel consumption are also offered.
DriveGreen can be displayed on the Infotainment as follows.
›
Press the button  in the Infotainment and then in the display the function
keys one after the other →
DriveGreen .
A
driving liquid display
With the driving is liquid the display is near the green dot. When accelerating
or braking, the indicator moves down or up.
B
“Green leaf”
The leaf margin shown in green shows with a few seconds, the current drive
efficiency. When driving economically there are several green layers on the
edge of the leaf. Otherwise no green colour appears and the leaf can disappear
completely.
C
Graphical review summary
The evaluation of the driving economy during the last 3 minutes or 1.5 minutes
(depending on type of Infotainment) is shown like a beam in 5-second incre-
ments. The current status is shown on the left and moves gradually to the
right. The higher the green bars, the more economic the driving style is.
D
Scoring
In the function key, the evaluation of driving efficiency is shown from the start
in the range from 0 to 100 points. The higher the indicated value, the more
economic the driving style is.
When you press the function key, a detailed assessment showing the driving
efficiency during the last 30 minutes is shown. 
112Driving

Downloaded from www.Manualslib.com manuals search engine Note■Note the embarked code number on both the adapter and at the end of each
anti-theft wheel bolt. This number can be used to purchase a ŠKODA Original
Parts replacement adapter, if necessary.■
The anti-theft wheel bolt set and adapter can be purchased from a ŠKODA
Partner.
■
The position of the anti-theft wheel bolt is marked on the back of the wheel
cover with every ŠKODA supplied original equipment hub cap or directly at the
factors. When using an anti-theft wheel bolt, make sure that this has been fit-
ted according to the position marked on the back of the wheel cover position.
Loosening/tightening wheel bolts
Fig. 174
Changing a wheel: Loosening the
wheel bolts
Before removing the wheel bolts the caps from the wheel bolts must be re-
moved.
Undoing
›
Push the wheel wrench onto the wheel bolt as far as the stop 1)
.
›
Grasp the end of the wrench and turn the bolt about one turn in the direction
of the arrow » Fig. 174.
Tightening
›
Push the wheel wrench onto the wheel bolt as far as the stop 1)
.
›
Grasp the end of the wrench and turn the bolt against the direction of the
arrow » Fig. 174 until it is tight.
After tightening the wheel bolts the caps must be re-fit.
WARNINGIf it proves difficult to undo the bolts, carefully apply pressure to the end of
the wrench with your foot. Keep hold of the vehicle when doing so, and
make sure you keep your footing.
Raising the vehicle
Fig. 175
Jacking points for positioning
lifting jack
Fig. 176
Attach lifting jack
To lift the vehicle, us the jack from the tool kit.
Position the car jack at the jacking point closest to the flat tyre.
The jacking points are located on the metal bar of the lower beam.
The positions of these are embossed by means of markings on the side sur-
face of the lower sill » Fig. 175. 
1)
Use the appropriate adapter for undoing and tightening the anti-theft wheel bolts
» page 169.
170Do-it-yourself

Downloaded from www.Manualslib.com manuals search engine No.Power consumer11Not assigned12Engine components13Brake pedal switch14Engine components, coil of the fuel pump relay15Engine control unit16Starter17Engine control unit18Engine components, coils of the relay for auxiliary electric heater, radi-
ator fan19Lambda probe20Engine components, control unit for glow plug system, heating the
crankcase ventilation
Replacing bulbs
 Introduction
This chapter contains information on the following subjects:
Bulb arrangement in the headlights
185
Removing and installing the cover in the front wheel arch
185
Fitting and removing the wash water container nozzle
185
Replacing the low beam and high beam bulb (halogen headlights)
186
Change bulb for turn signal switch (halogen headlight)
186
Replacing the parking light bulb (halogen headlights)
187
Changing bulb for daytime running lights switch (halogen headlight)
187
Replacing the dipped beam bulb (halogen projector headlights)
187
Replacing the high beam bulb (halogen projector headlights)
188
Replacing the turn signal switch bulb (halogen projector headlights)
188
Replacing the bulb for the fog light
189
Changing the licence plate light bulb
189
Rear Light
190
Replacing bulbs in rear light
190
Some manual skills are required to change a bulb. For this reason, if uncertain,
we recommend that bulbs are replaced by a specialist garage or other expert
help is sought.
› Switch off the ignition and all of the lights before replacing a bulb.
› Faulty bulbs must only be replaced with the same type of bulbs. The designa-
tion is located on the light socket or the glass bulb.
› A stowage compartment for replacement bulbs is located in a plastic box in
the spare wheel or underneath the floor covering in the boot.WARNING■ Always read and observe the warnings before completing any work in the
engine compartment » page 149.■
Accidents can be caused if the road in front of the vehicle is not suffi-
ciently illuminated and the vehicle cannot or can only be seen with difficul-
ty by other road users.
■
Bulbs H8, H7 and H4 are pressurised and may burst when changed - there
is a risk of injury! We therefore recommended wearing gloves and safety
glasses when changing a bulb.
■
Switch off the respective vehicle light when changing the bulb.
CAUTION
Do not take hold of the glass bulb with naked fingers (even the smallest
amount of dirt reduces the working life of the light bulb). Use a clean cloth,
napkin, or similar.
Note
■ This Owner's Manual only describes the replacement of bulbs where it is pos-
sible to replace the bulbs on your own without any complications arising. Other
light bulbs should be changed by your specialist garage.■
We recommend that you always carry a box of replacement bulbs in the vehi-
cle. Replacement bulbs can be purchased from ŠKODAOriginal Accessories.
■
We recommend having the headlight settings checked by a specialist garage
after replacing a bulb in the main beam, low beam or fog lights.
■
Visit a specialist garage if an LED is faulty.
184Do-it-yourself

Downloaded from www.Manualslib.com manuals search engine Bulb arrangement in the headlightsFig. 194
Principle sketch: Halogen headlights/halogen projector head-
lights
Read and observe
and on page 184 first.
The vehicle is equipped with headlights with halogen bulbs.
Bulb arrangement » Fig. 194
Dayl. dri. light
Low beam, high beam and parking light
Flashing
Low beam
High beam and turning signal switch
Removing and installing the cover in the front wheel arch
Fig. 195
Remove the plastic cover
Read and observe and on page 184 first.
The cover in the front wheel must be removed in order to change certain light
bulbs.
ABCDEDetails about removing the cover - if needed - are given in the description of
each lamp change.
Removing›
Adjust front wheels in the direction of centre of the vehicle.
›
Insert the clamp for removing the full wheel covers » page 167, Vehicle tool
kit into the recess in the cover.
›
Remove the cover by pulling the hook in the direction of arrow » Fig. 195.
Fitting
›
Insert and push the cover into the corresponding opening.
The cover must engage securely.
Fitting and removing the wash water container nozzle
Fig. 196
Remove the holder of the wash water container nozzle
Read and observe
and on page 184 first.
The holder of the wash water container nozzle must be removed in order to
replace some light bulbs. The holder is located in the engine compartment,
front right. 
185Fuses and light bulbs

Downloaded from www.Manualslib.com manuals search engine Details about removing the holder - if needed - are given in each lamp replace-
ment description .
Removing›
Unclip the container nozzle
A
from the holder in the direction of arrow
1
» Fig. 196 .
›
Insert a finger into the recess
B
in the direction of arrow
2
and lift the catch
C
in the direction of arrow
3
.
›
Remove the holder of the container nozzle in the direction of arrow
4
.
Fitting
›
Slide the holder of the container nozzle in the opposite direction to the ar-
row
4
» Fig. 196 .
The holder must engage firmly.
›
Push the container nozzle into the holder in the opposite direction to the ar-
row
1
.
Replacing the low beam and high beam bulb (halogen headlights)
Fig. 197
Replacing the bulb for low beam and main beam
Read and observe
and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185.
To replace lamp, first remove the bracket of the wash water container nozzle
in the right headlight » page 185.
›
Remove the protective cap
B
» Fig. 194 on page 185 .
›
Press the connector latch and remove the plug connector by jiggling in the
direction of arrow
1
» Fig. 197 .
›
Push in the spring in the direction of the arrow
2›
Release the spring in the direction of the arrow
3
.
›Remove the defective bulb in the direction of arrow 4.›Fit a new bulb into the headlamp and secure the spring in the opposite direc-
tion to the arrow 3
.
›
Insert the plug in the opposite direction to the arrow
1
.
›
Fit protective cap
B
» Fig. 194 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
›
Replace the appropriate cover in the front wheel arch » page 185.
Change bulb for turn signal switch (halogen headlight)
Fig. 198
Changing the bulb for the front
turn signal light
Read and observe and on page 184 first.
Remove the holder of the wash water container nozzle before replacing the
lamp in the right headlight » page 185.
›
Remove the protective cap
C
» Fig. 194 on page 185 .
›
Turn the socket with the bulb in the direction of arrow
1
» Fig. 198 .
›
Remove the socket with the bulb in the direction of arrow
2
.
›
Insert the socket with the new bulb in the opposite direction to the arrow
2
.
›
Turn the socket with the new bulb in the opposite direction to the arrow
1
until it stops.
›
Fit protective cap
C
» Fig. 194 on page 185 .
186Do-it-yourself

Downloaded from www.Manualslib.com manuals search engine Replacing the parking light bulb (halogen headlights)Fig. 199
Change the light bulb for the parking light
Read and observe
and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185.
Remove the holder of the wash water container nozzle before replacing the
lamp in the right headlight » page 185.
›
Remove the protective cap
B
» Fig. 194 on page 185 .
›
Remove the bulb holder with the bulb by jiggling it out in the direction of the
arrow
1
» Fig. 199 .
›
Grasp the lamp socket at the places marked by arrows.
›
Remove the faulty bulb from the holder in the direction of the arrow
2
.
›
Push a new bulb into the bulb holder up to the stop.
›
Replace the bulb holder in the headlamp with the bulb.
›
Fit protective cap
B
» Fig. 194 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
›
Replace the appropriate cover in the front wheel arch » page 185.
Changing bulb for daytime running lights switch (halogen
headlight)Fig. 200
Changing the bulb for the day-
time running light
Read and observe and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185.
›
Turn the socket with the bulb in the direction of arrow
1
» Fig. 200 .
›
Remove the socket with the bulb in the direction of arrow
2
.
›
Change the bulb in the socket.
›
Insert the socket with the new bulb into the headlight in the opposite direc-
tion to the arrow
2
.
›
Turn the socket with the new bulb in the opposite direction to the arrow
1
until it stops.
›
Replace the appropriate cover in the front wheel arch » page 185.
Replacing the dipped beam bulb (halogen projector headlights)
Fig. 201
Changing the bulb for the low beam
Read and observe
and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185. 
187Fuses and light bulbs

Downloaded from www.Manualslib.com manuals search engine Heating94
Control elements96
Exterior mirrors69
Seats71
HHC116
Hill Start Assist (HHC)116
Hitch127
Drawback load127
Hooks85
Horn26
I
Ice scrapers
142
Ignition lock101
Immobilizer100
Individual settings Locking
52
Unlocking52
Inertia reel13
Information system39
Compass point display45
Door warning39
Gear recommendation39
MAXI DOT display42
Multifunction display40
operation40
Service interval display46
Information system operation40
Infotainment4
Instrument cluster27
Auto-check control39
Counter for distance driven30
Display29
Fuel gauge30
Overview28
Revolution counter28
Temperature gauge29
Warning lights31
Interior care144
Natural leather145
interior light Front
64
Interior monitor55
ISOFIX22
J
Jack
167
Maintenance143
Jacking points Raise vehicle
170
Jump-starting174
K
KESSY Locking
51
Unlocking51
Key Locking
50
Start the engine101
Stopping the engine101
Switch off the ignition101
Switch on the ignition101
Unlocking50
L
Lamp failure Warning light
37
Lamps Warning light
37
Leather Natural leather care
145
LEAVING HOME63
Lever Main beam
61
Turn signal61
Levers Windscreen wipers
67
LightCockpit64
COMING HOME / LEAVING HOME63
Fog lights with CORNER function62
Lighting Luggage compartment
83
Lights59
Automatic driving lamp control61
Daylight running60
Fog lights62
Hazard warning light system63
Headlight flasher61
Headlight range adjustment60
Low beam60
Main beam61
parking lights60
Parking lights63
Rear fog light62
Replacing bulbs184
Switching on and off60
Turn signal61
Warning lights31
Locking Individual settings
52
KESSY51
Key50
Remote control50
Locking and unlocking the vehicle from the in- side
53
Locking the door without a locking cylinder Emergency
179
Low beam60
Luggage compartment83
Cover86
Fastening elements84
Fixing nets84
Flexible storage compartment88
Lighting83
Storage compartments under the floor87
unlock manually179
204Index

Downloaded from www.Manualslib.com manuals search engine Polishing vehicle paint worksee vehicle care141
Power Steering Warning light
32
Power windows56
Button in the front passenger door58
Force limitation58
Practical equipment Net pockets on the front seat rests
82
Reflective Vest166
Practical features Storage pockets on the front seats
81
Waste container78
Protective foils142
R
Radiator fan
152
Radio see Infotainment
4
Raise vehicle170
Rear interior light
65
Rear-view mirror Exterior mirrors
69
Rear fog light62
Warning light33
Rear mirror68
Rear view mirror Interior mirror
68
Rear window - heater65
Recirculated air mode96
Refuelling147
Fuel147
Remote control Locking
50
Replacing the battery177
Synchronisation process178
Unlocking50
Remote control key Replacing the battery177
Removing the bar ball, Step 1
131
bar ball, Step 2131
Repairs and technical alterations136
Replacing Bulb for the fog light
189
Bulb in rear light190
Bulbs184
High beam bulb (halogen projection-type head- lamp)
187
High beam bulb (halogen projector headlights) 188 Low beam and high beam bulb (halogen head- lights)
186
parking light bulb187
Rear window wiper blade180
turn signal switch bulb (halogen projector headlights)
188
Vehicle battery159
windscreen wiper blades180
Replenishing Coolant
155
Engine oil154
Windscreen washer fluid152
Reserve fuel Warning light
35
Revolution counter28
Rims160
Roller blind Luggage compartment cover
87
Roof Load
94
Roof rack93
mounting points94
Roof load94
Rubber seals141
Running-in Brake linings111
Engine111
Tyres111
S
SAFE see SafeLock
52
SafeLock52
SAFELOCK see SafeLock
52
Safety8
Child safety20
Child safety seats20
Correct seated position8
Headrests70
ISOFIX22
TOP TETHER24
Save electrical energy111
Save fuel111
Seals Vehicle care
141
Seat Adjusting
70
Seat belt height adjustment
12
Warning light32, 36
Seat belts11
Belt tensioners14
fastening and unfastening13
Seatbelts Inertia reels
13
Seat belts The physical principle of a frontal collision
12
Seat features71
Seats Armrest
72
Headrests70
Heating71
206Index