2014 Seat Toledo spare wheel

Advice
Vehicle tool kit* Fig. 122
Vehicle tool kit. The vehicle tool kit and the jack are stored in
a box on the spare wheel or in the spare
wheel well. There is also enough space for
the towing bracket ball coupling. The box is
strapped to the spare wheel with tape.
The vehicle tool kit includes the following
parts (depending on equipment):
Screwdriver
Adapter for anti-theft wheel bolts
Towline anchorage
Wire hook for removing hub caps
Jack
Box spanner for wheel bolts
Clip for wheel bolt cover
Spare set of bulbs
1 2
3
4
5
6
7
8 Before stowing the jack again, screw down
the arm as far as it will go.
WARNING
● The factory-supplied jack is only designed
for changing wheels on this model of vehicle.
On no account attempt to use it for lighting
heavier vehicles or other loads. Risk of injury!
● Make sure that the vehicle tools are stored
properly in the luggage compartment. Note
● Make sure the box always remains strap-
ped to the spare wheel with tape.
● The jack does not generally require any
maintenance. If required, it should be
greased using universal type grease. Changing a wheel
Introduction WARNING
● If you have a puncture in moving traffic,
switch on the hazard warning lights and
place the warning triangle at the obligatory
distance. Observe applicable local legal regu-
lations. This is for your own safety and that of
other drivers. ●
If you have a flat tyre, stop the vehicle as
far away as possible from moving traffic. Stop
on flat, solid ground.
● If you have to change the tyre on a gradi-
ent, block the wheel opposite the wheel be-
ing changed by placing a stone or similar ob-
ject under it to prevent the vehicle from roll-
ing away unexpectedly.
● If the vehicle has been fitted with tyres or
alloys that are different to those fitted in
manufacture, the instructions ››› page 146,
Replacing tyres and wheels must be followed.
● Always raise the vehicle with the doors
closed.
● Never place parts of your body, e.g. arms
and legs, underneath the vehicle when it is
supported only by the jack.
● Secure the base of the jack with suitable
supports so that it cannot slip. The jack could
slide if the ground below it is soft and slip-
pery and the vehicle could slip off it. There-
fore, place the jack on a firm surface or use a
large, stable base. On a slippery surface, e.g.
tile, use a non-slip base such as a rubber
mat.
● Never start the engine when the vehicle is
jacked. Risk of injury.
● The jack should only be used in the correct
jacking points. CAUTION
● The prescribed tightening torque for wheel
bolts on steel and alloy wheels is 120 Nm. 150

Emergencies
●
If the anti-theft wheel bolt is overly tight-
ened, this could damage the bolt and the
adapter. Note
● The set of anti-theft wheel bolts or the
adapter are available from authorised SEAT
dealers.
● Please observe the relevant local legal reg-
ulations when changing the wheel. Preparation work
Some preparation is required before chang-
ing a wheel:
– If you have a flat tyre, stop the vehicle as
far away as possible from moving traffic.
The surface must be horizontal.
– All vehicle occupants should leave the ve-
hicle . Vehicle occupants should wait in a
s af
e place, e.g. behind the roadside crash
barrier) while the wheel is being changed.
– Switch off the ignition and engage neutral
or move the selector lever on the automatic
g

earbox to position P.
– Apply the handbrake firmly.
– If t

owing a trailer, unhitch it. –
Take the vehicle tool kit ››
› page 150 and
the spare wheel ››› page 150 out of the lug-
gage compartment.
Wheel trim Removing
– Place the hook from the vehicle tool kit on
the reinforced edge of the wheel trim.
– Insert the box spanner through the hook,
supporting it on the tyre and remove the
wheel trim.
Fitting – First press the wheel trim onto the wheel at
the cut out designed for the valve. Then
press the wheel trim on both sides in the
direction of the valve so that it fits correctly
in place around all the perimeter. CAUTION
● Press down by hand, do not hit the wheel
trim! Knocking it sharply, particularly at
points where the wheel trim has not yet been
inserted, could result in damage to the wheel
trim guiding and centring elements.
● Before fitting the trim on a steel wheel at-
tached with an anti-theft wheel bolt, make
sure the bolt is in the hole in the valve area
››› page 154, Anti-theft wheel bolts*. ●
Where trim is fitted at a later date, ensure
enough air inflow is guaranteed in order to
cool the brake system. Wheel bolt caps
Fig. 123
Pull off the wheel bolt cap. Removing
– Insert the plastic clip into the cap until the
inner retaining notches on the clips touch
the collar of the cap and then remove it
››› Fig. 123 .
Fittin g
– In

sert the caps as far as they will go over
the wheel bolts.
The wheel bolt caps are stored in a box on
the spare wheel or in the spare wheel well.
151
Technical specifications
Advice
Operation
Safety

Advice
Wheel bolts The wheel bolts
are m atched to the rims.
When installing different wheels, e.g. to fit
light alloy wheels or wheels with winter tyres,
it is important to use the correct wheel bolts
with the right length and correctly shaped
bolt heads. This is essential for a secure fit of
the wheels and for proper operation of the
brake system.
Changing a wheel If possible, change the wheel on a level sur-
face.
– Pull off the hub cap ›››
page 151 or the
wheel bolt covers ›››
page 151.
– First loosen the anti-theft wheel bolts and
then the other wheel bolts ›››
page 152.
– Raise the vehicle until the wheel to be
changed is no longer touching the ground
››› page 153 .
– Remo

ve the wheel bolts and place them on
a clean surface (cloth, paper, etc.).
– Take off the wheel.
– Lift the spare wheel into position and tight-
en the wheel bolts lightly.
– Lower the vehicle. –
Tighten the wheel bolts firmly in diagonal
sequence with the box spanner and then
the anti-theft wheel bolt ››› page 152.
– Replace the hub cap and/or the bolt cov-
ers. Note
● All bolts must be clean and turn easily.
● Never grease or oil the wheel bolts!
● Note the direction of rotation when putting
on a tyre with a directional tread pattern
››› page 144. After changing a wheel
Tasks that must be carried out after changing
a wheel:
– Place the wheel with the defective tyre in
the spare wheel well and secure it using a
special bolt ›››
page 146 .
– Put

the vehicle tools back in their storage
location.
– Check the tyre pressure of the newly fitted
s

pare wheel as soon as possible.
– Have the tightening torque of the wheel
bo

lts checked as soon as possible with a
torque wrench.
– Have the flat tyre replaced or ask an Official
Service about the possibility of repair. Note
● If you notice that the wheel bolts are rusty
and difficult to turn when changing a wheel,
they must be replaced before having the
tightening torque checked.
● Drive carefully and at moderate speeds un-
til the tightening torque of the wheel bolts
has been checked. Loosening and tightening wheel bolts
Fig. 124
Changing a wheel: loosen the wheel
bolts. 152

Advice
– Adjust the jack so that its claw surrounds
the jacking point on the door sill ››› Fig. 126
- B underneath the stamp on the door sill.
– Make sure that the base of the jack is en-
tirely supported on a flat surface and that it
is vertical ››› Fig. 126 to the point where the
c l
aw surrounds the jacking point on the
door sill.
– Continue to wind up the jack using the
crank handle until the defective wheel is
clear off the ground.
Anti-theft wheel bolts* Fig. 127
Anti-theft wheel bolt with adapter. On vehicles fitted with anti-theft wheel bolts
(one bolt per wheel) these bolts can only be
loosened or tightened using a factory-sup-
plied adapter.
– Pull off the hub cap or bolt cover. –
Insert the adapter B
››› Fig. 127 with its
t oothed s

ide as far as it will go on the inte-
rior toothing of the anti-theft wheel bolt A so that only the outer hexagonal is protrud-
ing.
– Fit the box spanner as far as it will go over
adapter B .
– Loosen or firmly tighten the wheel bolt
››› page 152 .
– Af t

er removing the adapter, replace the hub
cap or the anti-theft wheel bolt cover.
– Have the tightening torque of the wheel
bo

lts checked as soon as possible with a
tor
que wrench.
Note down the code number stamped on the
front of the adapter or on the front of the anti-
theft wheel bolt. You will need this number to
obtain a spare adapter from the SEAT original
accessories programme.
We recommend you always carry the wheel
bolt adapter in the vehicle. It should be stor-
ed in the vehicle tool kit.
Tyre repairs TMS (Tyre Mobility System)* The Tyre Mobility System is stored in a box
under the carpet in the boot.Using the Tyre Mobility System you can relia-
bly seal tyres damaged by foreign bodies,
provided that cuts or punctures are no larger
than approx. 4 mm in diameter. Do not re-
move the foreign bodies, e.g. bolts or nails,
from the tyre!
The tyre must be repaired immediately.
The repair made using the Tyre Mobility Sys-
tem
under no circumstances replaces
perm
a-
nent
tyre repair and should only be used to
drive to the nearest official service.
The Tyre Mobility System kit shall not be
used:
● If the wheel rim has been damaged,
● when the outside temperature is below
-20 °C (-4 °F),
● on slashes or punctures larger than 4 mm,
● if the sidewall of the wheel has been dam-
aged,
● If you have been driving with very low tyre
pressure or a completely flat tyre
● If the best-before date on the air can has
expired WARNING
Read and observe the safety warnings ››› in
Introduction on page 150.
● A ty r

e filled with sealant does not have the
same performance properties as a conven-
tional tyre. 154

Emergencies
●
Do not drive faster than 80 km/h (50 mph).
● Avoid heavy acceleration, hard braking and
fast cornering.
● Check the tyre pressure after 10 minutes of
driving!
● The sealant is harmful to health and must
be immediately rinsed from affected skin. For the sake of the environment
Used or out-of-date sealant must be disposed
of in line with environmental protection regu-
lations. Note
● Observe the usage instructions provided by
the snow chain manufacturer.
● A new can of sealant can be acquired from
the selection of SEAT Original Accessories.
● Change the tyre repaired using the Tyre
Mobility System as soon as possible or ask
an official service about the possibility of re-
pairing it for you. Components of the Tyre Mobility
System*
Fig. 128
Contents of the Tyre Mobility System. The Tyre Mobility System contains the follow-
ing components:
An adapter to fit and remove the valve
Sticker indicating the speed: “max. 80
km/h” or “max. 50 mph”
Flexible filling hose with cap
Compressor
Flexible tyre inflating hose
Tyre pressure gauge
Air release screw
ON/OFF button
12 V cable connector ››› page 79
Can of sealant
1 2
3
4
5
6
7
8
9
10 Spare valve
The valve extractor 1
››› Fig. 128 has a slot
in its lo
wer end that fits onto the valve insert.
This is used to remove the valve insert from
the tyre and to replace it. This is also valid for
the spare valve insert 11 .
Work prior to using the Tyre Mobility
System The following jobs must be performed before
using the Tyre Mobility System:
– If you have a flat tyre, stop the vehicle well
away from moving traffic. Stop on flat, solid
ground.
– All vehicle occupants should leave the ve-
hicle . Vehicle occupants should wait in a
s af

e place (e.g. behind the roadside crash
barrier) while the wheel is being changed.
– Switch off the ignition and engage neutral
or move the selector lever on the automatic
g

earbox to position P.
– Apply the handbrake firmly.
– Check

whether the tyre can be repaired us-
ing the Tyre Mobility System ›››
page 154.
– If towing a trailer, unhitch it.
– Remove the Tyre Mobility System from the
boot

. »
11
155
Technical specifications
Advice
Operation
Safety

Advice
● Replace the cover again or close the fuse
box lid. CAUTION
If you replace a fuse with higher-rating fuse,
you could cause damage to another part of
the electrical system. Changing bulbs
Introduction Changing bulbs requires a certain degree of
practical skill. If in doubt, we recommend you
have defective bulbs changed by a special-
ised service or, in case of an emergency,
seek professional assistance.
●
Switch off the ignition and all of the lights
before changing a bulb.
● Do not touch the glass part of the bulb with
your bare hands. The fingerprints left on the
glass will vaporise as a result of the heat gen-
erated by the bulb, reducing bulb life and
causing condensation on the reflector sur-
face, thus reducing effectiveness.
● A bulb must only be replaced by one of the
same type. The type is indicated on the bulb,
either on the glass part or on the base.
● There is a storage area for the bulb box in
the spare wheel well or below the carpet in
the luggage compartment. The light source used for each function is lis-
ted below:
Double headlights
H7 Long Life
H7
W5W Long Life PY21W NA P21W Super Long Life WARNING
● Take particular care when working on com-
ponents in the engine compartment if the en-
gine is warm. Risk of burns.
● Bulbs are highly sensitive to pressure. The
glass can break when you touch the bulb,
causing injury.
● The high voltage element of gas discharge
bulbs* (xenon light) must be handled correct-
ly. Otherwise, there is a risk of death.
● When changing bulbs, please take care not
to injure yourself on sharp parts in the head-
light housing. CAUTION
● Remove the ignition key before working on
the electric system. Otherwise, a short circuit
could occur.
● Switch off the lights and the parking light
before changing a bulb. Dipped beam:
Main beam:
Side lights:
Turn signals:
Daytime driving lights: For the sake of the environment
Please ask your specialist retailer how to dis-
pose of used bulbs in the proper manner. Note
● Depending on weather conditions (cold or
wet), the front lights, the fog lights, the rear
lights and the turn signals may be temporari-
ly misted. This has no influence on the useful
life of the lighting system. By switching on
the lights, the area through which the beam
of light is projected will quickly be demisted.
However, the edges may continue to be mis-
ted.
● Please check at regular intervals that all
lighting (especially the exterior lighting) on
your vehicle is functioning properly. This is
not only in the interest of your own safety,
but also that of all other road users.
● Before changing a bulb, make sure you
have the correct new bulb.
● Do not touch the glass part of the bulb with
your bare hands, use a cloth or paper towel
instead. Otherwise, the fingerprints left on
the glass will vaporise as a result of the heat
generated by the bulb, they will be deposited
on the reflector and damage its surface. 166

Technical specifications
Type plate
The type plate ››› Fig. 165 is located at the
bott om of
the front driver side door pillar be-
tween the front and rear doors.
The type plate indicates the following
weights:
Total permitted weight of the vehicle
when loaded
Maximum authorised weight of the vehi-
cle with a trailer, when the vehicle oper-
ates as a tractor
Maximum permitted load of the front axle
Maximum permitted load of the rear axle
Weight in running order
The weight in running order only has one ap-
proximate value. This value corresponds to
the minimum operative weight of the vehicle
without additional equipment that increases
its weight, i.e. air conditioning, spare wheel,
towing bracket.
The running order weight also includes 75 kg
of the weight of the driver and service fluids,
in addition to a fuel tank at 90% capacity.
From the difference between the total permit-
ted weight in running order the approximate
carrying capacity can be calculated ››› .
The carrying capacity must include:
● occupants,
8 9
10
11 ●
all pieces of equipment and other weights,
● roof loads including the roof rack,
● equipment that is not included in the run-
ning order weight,
● when using the towing bracket, the draw-
bar load (max. 50 kg)
Calculating fuel consumption and CO 2
emissions according to the ECE regulations
and the EU specifications
Calculation of fuel consumption for urban
driving begins when cold-starting the engine.
Then, normal city driving is simulated.
In calculating extra-urban driving fuel con-
sumption, braking and acceleration is done
in all gears, as in daily use of the vehicle.
Driving speed varies within a range of 0 and
120 km/h (75 mph).
The consumption value in combined driving
is composed of 37% of the value of urban
driving and 63% of the value of extra-urban
driving. WARNING
The maximum permitted weight values must
not be exceeded – Risk of an accident and
damage to the vehicle! Note
● If you wish to calculate the exact weight of
your vehicle please contact a SEAT dealer. ●
Depending on the volume of equipment,
driving style, road conditions, weather condi-
tions and the condition of the vehicle, con-
sumption values can differ from the theoreti-
cal values stated here. Information on fuel
consumption
Fuel consumption The consumption and emission details
shown on the vehicle data sticker differ from
one vehicle to another.
Vehicle fuel consumption and CO
2 emissions
appear on the vehicle data sticker in the
spare wheel well, inside the boot and on the
rear cover of the Maintenance Programme.
The fuel consumption and CO 2 emission val-
ues refer to the weight category assigned to
your vehicle according to the engine and
gearbox combination, as well as the specific
equipment fitted, and is only used to com-
pare between the different models.
The fuel consumption and CO 2 emissions do
not depend only on the performance of the
vehicle, they can also differ from the estab-
lished values depending on other factors
such as driving style, road conditions, traffic
conditions, environmental conditions, load
and number of passengers. »
175
Technical specifications
Advice
Operation
Safety

Index
Seat belt tensioner control lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Seat belt tensioners . . . . . . . . . . . . . . . . . . . . . . . . 15
Seats adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
head restraints . . . . . . . . . . . . . . . . . . . . . . . . . . 72
heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Selector lever see selector lever positions . . . . . . . . . . . . . . . 101
Selector lever positions . . . . . . . . . . . . . . . . . . . . 101
Service display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Setting clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Settings exterior mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Interior rear vision mirror with manual anti-dazzle adjustment . . . . . . . . . . . . . . . . . . . . . 70
light range control . . . . . . . . . . . . . . . . . . . . . . . 62
Side airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 safety instructions . . . . . . . . . . . . . . . . . . . . . . . 20
Sitting position driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Sitting position for vehicle occupants . . . . . . . . . . 6
Snow chains . . . . . . . . . . . . . . . . . . . . . . . . 149, 177
Spare changing a wheel . . . . . . . . . . . . . . . . . . . . . . . 150
Spare wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
Speedometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 see speedometer . . . . . . . . . . . . . . . . . . . . . . . . 31
Start-Stop description . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Starting the engine . . . . . . . . . . . . . . . . . . . . . . . . 97
Starting with jump leads jump-starting . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Steering wheel controls . . . . . . . . . . . . . . . . . . . . . 46
Storage luggage compartment . . . . . . . . . . . . . . . . . . . . 82 Storage compartment . . . . . . . . . . . . . . . . . . . 76, 85
Summary
control lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
controls and displays . . . . . . . . . . . . . . . . . . . . . 29
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 see sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Switching off the engine . . . . . . . . . . . . . . . . . . . . 98
T Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
Temperature selection heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Tightening torque of wheel bolts . . . . . . . . . . . . 177
Tiptronic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 see automatic gearbox . . . . . . . . . . . . . . . . . . . 102
Tool kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Topping up coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
engine oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
windscreen washer . . . . . . . . . . . . . . . . . . . . . . 139
Top Tether system . . . . . . . . . . . . . . . . . . . . . . . . . 27
Tow-away protection system . . . . . . . . . . . . . . . . . 58
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Towing bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Towline anchorage . . . . . . . . . . . . . . . . . . . . . . . . 160 rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Traction control . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 Towing a trailer . . . . . . . . . . . . . . . . . . . . . . . . . 115
Trailer weights . . . . . . . . . . . . . . . . . . . . . . . . . . . 176
Transport roof rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Transporting children . . . . . . . . . . . . . . . . . . . . . . . 24
Trip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Trip counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Tyre Mobility System . . . . . . . . . . . . . . . . . . . . . . 154
see Tyre Mobility System . . . . . . . . . . . . . . . . . 154
Tyre pressures . . . . . . . . . . . . . . . . . . . . . . . . . . . . 177
Tyre repair kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 154
Tyre repair set see Tyre Mobility System . . . . . . . . . . . . . . . . . 154
Tyres see Wheels and tyres . . . . . . . . . . . . . . . . . . . . 146
Tyre tread . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
Tyre tread depth . . . . . . . . . . . . . . . . . . . . . . . . . . 144
U
Underbody sealant . . . . . . . . . . . . . . . . . . . . . . . . 127
Unlocking central locking system . . . . . . . . . . . . . . . . . . . . 55
remote control . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Unlocking and locking from the inside . . . . . . . . . 56
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
V
Vehicle care door lock cylinder . . . . . . . . . . . . . . . . . . . . . . . 126
Vehicle interior monitoring . . . . . . . . . . . . . . . . . . 58
Vehicle status see Auto-check system . . . . . . . . . . . . . . . . . . . 44
Vehicle tool kit . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Ventilation slits . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Voice control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
disabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
enter the number . . . . . . . . . . . . . . . . . . . . . . . . 50
W Warning symbols see warning lamps . . . . . . . . . . . . . . . . . . . . . . . 32
Warning triangle . . . . . . . . . . . . . . . . . . . . . . . . . . 149
192