Page 240 of 284

Advice
Removing tail light Fig. 217
Luggage compartment: location of
the bolt securing the tail light unit. Fig. 218
Remove the rear light unit from side
panel. –
Check which of the bulbs is defective.
– Open the rear lid.
– Remove the cover by prying the flat side of
a screwdriver into the recess and remove
the cover from the opening ››› Fig. 217 1 .–
Carefully loosen the screw located behind
the cover with a screwdriver, turning it anti-
clockwise (arrows) ››› Fig. 217 2 .
– Tilt the light in the direction of the arrows
until it comes out (positions 3 and
4 ›››
Fig. 218 ).
– Remo
ve the bulb holder ››› page 238. CAUTION
Take care when removing the rear light unit to
make sure there is no damage to the paint-
work or any of its components. Note
Make sure you have a soft cloth ready to
place under the glass on the rear light unit, to
avoid any scratches. Remove the bulb holder
Fig. 219
Retaining tabs on reverse side of tail
light. –
Remove the bulb holder ››› Fig. 219 unlock-
in g the r
etaining tabs 1 .
– Raise the bulb holder.
– Change the defective bulb.
– To refit follow the steps in reverse order,
taking special care when fitting the bulb
holder. And especially that all retaining
tabs are properly secured.
– Place the light back into place and tighten
with a screwdriver. Note
In the case of LED lights, change only the turn
signal bulb. 238
Page 241 of 284

Fuses and bulbs
Changing tail light bulbs (on
rear lid) Overview of tail lights Rear lights on tailgateLeft side
Side lights2x W5W LL
Fog lightsH21 W
Right side
Side lights2x W5W LL
Reverse lightP21W LL
The table corresponds to a right-hand traffic
vehicle. The position of lights may vary ac-
cording to the country.
Remove the bulb holder Fig. 220
Remove the cover from the boot lid. Fig. 221
Remove the lamp holder The rear lid must be open to change the
bulbs.
– Remove the rear lid cover in the direction
indicated ››› Fig. 220 .
– Un loc
k the retaining tabs A of the bulb
holder, following the direction of arrows 1 and
2
››› Fig. 221 . –
Remo
ve the bulb holder by turning it in the
direction of arrow 3
››› Fig. 221 .
Ch an
ging bulbs Fig. 222
Position of the bulbs in the bulb
holder –
Lightly press the defective bulb into the
bulb holder ››› Fig. 222 1 , then turn it to
the left 2 and remove it.
– Fit the new bulb, pressing it into the bulb
holder and turn it to the right as far as it
will go.
– Use a cloth to remove any fingerprints from
the glass part of the bulb.
– Check that the new bulb works properly.
– Replace the bulb holder.
»
239
Technical specifications
Advice
Operation
Safety
The essentials
Page 243 of 284

Technical specifications
Technical specifications
Technical specifications Important The information in the vehicle documentation
always takes precedence over the informa-
tion in this Instruction Manual.
All technical specifications provided in this
documentation are valid for the standard
model in Spain. The vehicle data card inclu-
ded in the Maintenance Programme or the
vehicle registration documents shows which
engine is installed in the vehicle.
The figures may be different depending
whether additional equipment is fitted, for
different models, for special vehicles and for
other countries.
Abbreviations used in the Technical
Specifications sectionAb-
brevia- tionMeaning
kWKilowatt, engine power measurement.
PSPferdestärke (horsepower), formerly used to
denote engine power.
rpmRevolutions per minute - engine speed.
NmNewton metres, unit of engine torque.
litresper
100 kmFuel consumption in litres per 100 km (70
miles).
g/kmCarbon dioxide emissions in grams per km
(mile) travelled.
CO 2Carbon dioxide
CNCetane number, indication of the diesel com-
bustion power.
RONResearch octane number, indication of the
knock resistance of petrol. Vehicle identification data
Fig. 225
Vehicle data sticker (boot). Fig. 226
Chassis number.
» 241
Technical specifications
Advice
Operation
Safety
The essentials
Page 245 of 284

Technical specifications
Note
In practice, and considering all the factors
mentioned here, consumption values can dif-
fer from those calculated in the current Euro-
pean regulations. Weights
Kerb weight refers to the basic model with a
fuel tank filled to 90% capacity and without
optional extras. The figure quoted includes
75 kg to allow for the weight of the driver.
Special versions, optional equipment fittings
or retro-fitting accessories will increase the
weight of the vehicle
››› .
WARNING
● Please note that the centre of gravity may
shift when transporting heavy objects; this
may affect vehicle handling and lead to an ac-
cident. Always adjust your speed and driving
style to suit road conditions and require-
ments.
● Never exceed the gross axle weight rating
or the gross vehicle weight rating. If the per-
missible axle load or the permissible total
weight is exceeded, the driving characteris-
tics of the vehicle may change, which could
lead to accidents, injuries and damage to the
vehicle. Towing a trailer
Trailer weights Trailer weight
The trailer weights and drawbar loads ap-
proved are selected in intensive trials accord-
ing to precisely defined criteria. The ap-
proved trailer weights apply to vehicles in the
EU and generally for maximum speeds of 80
km/h (100 km/h in c
er
tain circumstances).
The figures may be different in other coun-
tries. All data in the official vehicle documen-
tation takes precedence over these data at all
times ››› .
Drawbar loads
The maximum
permitted drawbar load on the
b
all joint of the towing bracket must not ex-
ceed
80 kg.
In the interest of road safety, we recommend
that you always tow approaching the maxi-
mum drawbar load. The response of the trail-
er on the road will be poor, if the drawbar
load is too small.
If the maximum permissible drawbar load
cannot be met (e.g. with small, empty and
light-weight single axle trailers or tandem
axle trailers with a wheelbase of less than 1
metre), a minimum of 4% of the actual trailer
weight is legally required for the drawbar
load. WARNING
● For safety reasons, do not exceed the 80
km/h (50 mph) limit. This is also valid in
countries where higher speeds are permitted.
● Never exceed the maximum trailer weights
or the drawbar load. If the permissible axle
load or the permissible total weight is excee-
ded, the driving characteristics of the vehicle
may change, leading to accidents, injuries
and damage to the vehicle. Wheels
Tyre pressure, snow chains, wheel
bolts Tyre pressures
The sticker with the tyre pressure values can
be found on the inside of the fuel tank flap.
The tyre pressure values given there are for
cold
tyres. The slightly raised pressures of
w arm ty
res must not be reduced. ››› Snow chains
Snow chains may be fitted only to the front
wheels, and only for the following tyres:
»
243
Technical specifications
Advice
Operation
Safety
The essentials