2014 Ram ProMaster turn signal

Fog Lights — If Equipped
The fog light switch is located on the center
stack of the instrument panel, just below the
climate controls. Press the switch once to turn
the fog lights on. Press the switch a second time to turn
the fog lights off.
Turn Signals
Move the multifunction lever up or down and the arrows
on each side of the instrument cluster flash to show
proper operation of the front and rear turn signal lights.
NOTE: If either light remains on and does not flash, or
there is a very fast flash rate, check for a defective outside
light bulb. If an indicator fails to light when the lever is
moved, it would suggest that the indicator bulb is
defective.
Parking Lights
These lights can only be turned on with ignition key in
the STOP position or removed, by moving the end of the
multifunction lever to O (off) position and then to the
headlight position.
The warning light telltale in the instrument panel comes
on. The lights stay on until the next ignition cycle is
performed.
Lane Change Assist
Tap the lever up or down once, without moving beyond
the detent, and the turn signal (right or left) will flash five
times then automatically turn off.
High Beam/Low Beam Select Switch
Pull the multifunction lever toward you to switch the
headlights to high beam. Pull the lever a second time to
switch the headlights back to low beam.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93

Flash-To-Pass
You can signal another vehicle with your headlights by
partially pulling the multifunction lever toward the steer-
ing wheel. This will cause the high beam headlights to
turn on until the lever is released.
Follow Me Home/Headlight Delay
When this feature is selected the driver can choose to
have the headlights remain on for a preset period of time.
Activation
Remove the key or turn the ignition to the OFF/LOCK
position, and pull the multifunction lever toward the
steering wheel, within two minutes. Each time the lever
is pulled, the activation of the lights will be extended by
30 seconds. The activation of the lights can be extended to
a maximum of 210 seconds.The warning light on the instrument panel will light up
and the corresponding message will appear in the EVIC
display for as long as the function is activated. The
warning light comes on when the lever is operated and
stays on until the function is automatically deactivated.
Each movement of the lever only increases the amount of
time the lights stay on.
Deactivation
Pull the multifunction lever toward the steering wheel
and hold it for more than two seconds.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

While audible signals are emitted, the audio system is not
muted.
The audible signal is turned off immediately if the
distance increases. The tone cycle remains constant if the
distance measured by the inner sensors is constant. If this
condition occurs for the external sensors, the signal is
turned off after three seconds (stopping warnings during
maneuvers parallel to walls).
ParkSense® Rear Park Assist Failure Indications
A malfunction of the ParkSense® Rear Park Assist sen-
sors or system is indicated, during REVERSE gear en-
gagement, by the instrument panel warning icon.The warning icon is illuminated and a message
is displayed on the multifunction display (if
equipped). Refer to “Instrument Cluster De-
scriptions” in “Understanding Your Instrument
Panel” for further information. The sensors and wiring are tested continuously when the
ignition is in the ON/RUN position. Failures are indi-
cated immediately if they occur when the system is ON.
Even if the system is able to identify that a specific sensor
is in failure condition, the instrument cluster display shall
indicate that the ParkSense® Rear Park Assist system is
unavailable, without reference to the sensor in failure
condition. If even a single sensor fails, the entire system
must be disabled. The system is turned off automatically.
Cleaning The ParkSense® Rear Park Assist
System
Clean the ParkSense® Rear Park Assist sensors with
water, car wash soap and a soft cloth. Do not use rough
or hard cloths. In washing stations, clean sensors quickly
keeping the vapor jet/high pressure washing nozzles at
least 4 in (10 cm) from the sensors. Do not scratch or poke
the sensors. Otherwise, you could damage the sensors.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109

INSTRUMENT CLUSTER DESCRIPTIONS
1. Speedometer
The speedometer shows the vehicle speed in miles per
hour (mph) and/or kilometers per hour (km/h).
2. Turn Signal IndicatorsThe arrow will flash with the exterior turn
signal when the turn signal lever is operated.
NOTE: •A continuous chime will sound if the vehicle is
driven more than 1 mile (1.6 km) with either turn
signal on.
• Check for an inoperative outside light bulb if either
indicator remains on and does not flash, or flashes at
a rapid rate. 3. Stop Light Failure Indicator
This light will illuminate if one or more of the stop light
bulb fails.
The failure relating to this light could be: one or more
blown bulbs, a blown protection fuse or a break in the
electrical connection.
4. Front Fog Light Indicator — If Equipped
This indicator will illuminate when the front
fog lights are on.
5. High Beam Indicator This light shows that the high beam headlights
are on. Pull the multifunction lever toward you
to switch the headlights to high beam. Pull the
lever a second time to switch the headlights back to low
beam.
128 UNDERSTANDING YOUR INSTRUMENT PANEL

Volume
Turn the ROTARY knob clockwise to increase the vol-
ume. Turning it counterclockwise will lower the volume.
The volume can be set between 0 and 30.
Tuner Mode (AM/FM Radio)
When you enter TUNER mode, the radio tunes to the
most recently selected station and will remain on the
most recently selected frequency band.
In this mode of operation the display will show one of the
following 5 codes:
CH (Channel)
When this is on, it indicates that the current radio station
is stored in memory. The code is only shown when the
tuned frequency is showing on the display.
ST (Stereo)
When this is on, it indicates that the radio station is
transmitting a 19 kHz signal (pilot).Searching for Stations In Automatic Mode
When you press
orfor less than two seconds, the
radio will search for the next valid station. While the
radio is searching for the new station, the display will
show SEEKING. When the search is complete, the
display will show the tuned frequency band and
station in the format F1 106.9or, if the station was
previously stored in memory, the display will show
the channel where it is stored and the tuned station.
Searching for Stations In Manual Mode
Pressing
orfor more than two seconds displays
the selected radio station frequency. Each time a
button is pressed, the radio station frequency is in-
creased or decreased according to the default search
pattern for the selected band (100 kHz for FM and 10k
Hz for AM). When the search button is pressed and
held, the radio station frequency will continue to be
increased or decreased. If the buttons are not pressed
4
UNDERSTANDING YOUR INSTRUMENT PANEL 159

for five seconds, the display will show the message
AUTOand manual search mode will be canceled.
When the search is complete, the display will show the
tuned band and station in the format F1 106.9,or,if
the station found was previously stored in memory,
the display will show the channel where it is stored
and the tuned station.
Mute/Pause
Pressing this button mutes the sound. The display will
switch between MUTE ONand the previous display
(3 seconds).
Pressing the button again restores the audio without
changing the original volume setting. The display will
show MUTE OFF for three seconds, and then return to
the previous display mode.
When the
or, Audio, 1, 2, 3, 4, 5, 6, BAND/AS
buttons and SRC are pressed in Mute / Pausedmode, these will be implemented and the audio will
be restored without changing the original volume.
Turn the ROTARY knob to restore the audio and change
the volume to the level selected. The display will show
the settings described in the volume function.
The other buttons should be implemented when pressed,
but the radio will remain in
MUTE ONmode.
Storing Stations In Memory
Press and hold the memory buttons (1 through 6) for
more than two seconds to associate the tuned station
with the pressed button. The display will show a message
in MEMO 2 format for three seconds to confirm that the
station has been tuned in. The CH signal is then activated
and the display will show the preset number and station
frequency for three seconds 2 106.9. The display will
then return to the previous view.
160 UNDERSTANDING YOUR INSTRUMENT PANEL

Accessing Preset Stations
When the preset buttons (1 through 6) are pressed for less
than two seconds the radio will tune in to the station
associated with that particular memory location. The
display shows the preset number and frequency of the
associated station for three seconds. The display will then
return to the previous view.
Retuning the band: When the BAND/AS button is
pressed for less than two seconds, the radio will alternate
between bands in the sequence: FM1
FM2FM3
AM1AM2FM1. While changing bands from
the FM3 band to
AM1, the display will show AM
for two seconds and when changing from the AM2
band to
FM1, the display will show FMfor two
seconds.
The display will then show the selected band and fre-
quency in the format F1 106.9for two seconds and then
return to the previous view. Presetting stations with a strong signal: when the
BAND/AS button is pressed for more than two seconds,
the radio will search for the 6 best stations and automati-
cally store them in the 6 memory positions of the current
band. During the search, the display will indicate
FM
AST orAM AST, depending on the band selected. To
record the stations that are found, these are sorted in
ascending order of frequency and the first one is stored in
memory position 1, and so on, until positions 1-6 are all
in use. If fewer than 6 stations are found, the unused
channels will be allocated to the 107.9 MHz frequency for
FM and AM 1710 KHz for the AM band. At the end of the
search process, the radio tunes in to the first preset
position and the display will indicate the associated
preset number (1) and the station frequency for three
seconds. The display will then return to the previous
view.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 161

Tire Pressure Monitoring Low Pressure Warnings
The Tire Pressure Monitoring Telltale Light will illumi-
nate in the instrument cluster, an audible chime will be
activated, and the “Check tire pressure” text message will
display when one or more of the four active road tire
pressures are low. Should this occur, you should stop as
soon as possible, check the inflation pressure of each tire
on your vehicle, and inflate each tire to the vehicle’s
recommended cold placard pressure value. The system
will automatically update and the Tire Pressure Monitor-
ing Light will extinguish once the updated tire pressures
have been received. The vehicle may need to be driven
for up to 20 minutes above 15 mph (24 km/h) to receive
this information.
Check TPMS Warnings
The Tire Pressure Monitoring Telltale Light will flash on
and off for 75 seconds and remain on solid when a system
fault is detected, an audible chime will be activated and
the “Tire Pressure Monitoring Unavailable” text message
will display. If the ignition key is cycled, this sequence
will repeat providing the system fault still exists. The Tire
Pressure Monitoring Telltale Light will turn off when the
fault condition no longer exists. A system fault can occur
with any of the following scenarios:
1. Jamming due to electronic devices or driving next tofacilities emitting the same radio frequencies as the
TPM sensors.
2. Installing some form of aftermarket window tinting that affects radio wave signals.
3. Snow or ice around the wheels or wheel housings.
5
STARTING AND OPERATING 253