2014 PORSCHE 911 TURBO clock setting

Opening and Locking 29
Door lock under door handle (driver‘s side)
The vehicle cannot be locked
This is recognizable by the fact that the emergency flasher does not flash and there is no locking noise.
The remote control of the key may – fail due to a fault,– due to a flat key battery,– not function correctly due to radio waves(e.g. mobile phone) in the vicinity of the vehicle (even radio contact between remote control and vehicle in the case of Porsche Entry & Drive).
Emergency locking if the central locking system has failed
If the vehicle cannot be locked, then: 1. Remove the emergency key from the car key. Please see the chapter “EMERGENCY KEY” on page 17.2. Open the driver’s door.
3. Lift the door handle on the driver’s door ( illustration). Insert the emergency key in the door lock, turn 90° clockwise and remove the emergency key again.Successful locking is indicated by the hazard warning lights flashing twice.4. Release the door handle and shut the door. The driver’s door is now locked.5. To use the emergency locking function on the passenger’s door , insert the emergency key into the door lock on the driver’s door again, turn 90° clockwise and remove the emergency key again.The passenger’s door is now locked.
Information
Emergency locking of the passenger’s door is not possible if the central locking system is defective.
Information
If the central locking system is defective, operating the lock cylinder in the driver’s door will lock all functioning locking elements of the central locking system.fHave faults in the central locking system repaired by an authorized Porsche dealer.
Emergency key
Removing emergency key
1. Push the release button to the side. 2. Pull out the key.
Insert emergency key
fPush in the key until the release button engages audibly.
Information
Different vehicle settings are stored on the respective key when the vehicle is locked, provided the vehicle is fitted with the relevant equipment.
14_991_Turbo_21.book Seite 29 Mittwoch, 9. April 2014 2:19 14

66 Windows, Sunroof and Cabriolet
1.Carefully lever off the cap from the roof liner using a screwdriver, for example.2. Take the hexagon key out of the tool kit in the luggage compartment.
For information on the tool kit:fPlease see the chapter “TOOLS” on page 198.
3. Insert the hexagon key all the way into the opening.4. Applying continuous upward pressure, turn the key clockwise until the roof is fully closed.5. Remove the key. 6. Refit the cap. 7. Stow the key in the tool kit.fHave the fault corrected at an authorized Porsche dealer.
Storing end position of the sunroof
The end positions of the roof are lost after disconnection/connection of the vehicle battery, if the vehicle battery is exhausted or after jump lead starting, after emergency operation or after changing the fuse for the roof.
The roof closes with its full closing force when storing the end position.fEnsure that nobody is injured when closing the roof.
The vehicle must be stationary in order to store the end position of the roof.1. Switch on ignition. 2. Pull and hold button C in the first setting until the roof closes and stops in the closed position.The process for storing the end position begins after approximately 10 seconds. The roof now opens and closes once automatically. Storage is now complete.If this process is not executed, please perform the following procedure:Pull and hold button C in the first setting until the roof closes fully and stops. If necessary, repeat the closing operation until the roof has stopped moving completely.The process takes a maximum of 15 seconds.Start the storing process again if the button is released before the roof has stopped moving completely.
Storing the end positionWARNINGh
14_991_Turbo_21.book Seite 66 Mittwoch, 9. April 2014 2:19 14

124 Instrument Panel and Multi-Function Display
Setting date and time
The date and time displays on the vehicle can be adjusted individually.
Information
On vehicles with Porsche Communication Management (PCM), the date and time are set and synchronized automatically by satellite navigation signals (GPS).Some setting options may be temporarily unavailable, depending on satellite signal reception.
Setting the time
The time, time format and time zone can be set in the “ Time” menu.
Displaying GPS time
The time can be synchronized via the GPS signal and displayed.
Setting the time format
The time can be displayed in 12-hour or 24-hour format.
Available setting options: –“ 12h” –“ 24h”
Setting current time
On vehicles without Porsche Communication Management (PCM), the hours and minutes can be set separately when setting the time.
Setting time zone
The time zone of the vehicle clock can be set individually on vehicles with Porsche Communication Management (PCM).
1. Main menu “Vehicle” > “ Settings” > “ Date & Time” and confirm.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time” > “ Time” and confirm.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time” > “ Time”
2.Select “GPS time”.
3.Confirm your selection.
Time synchronized with GPS.
Time not synchronized with GPS.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time” > “ Time”
2.“Format” and confirm.
3. Select the desired setting and confirm.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time” > “ Time”
2.Select “Hour/Minute”. in the main menu.
3. Set the desired time and confirm the setting.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time” > “ Time”
2.Select “Zone” and confirm.
3. Set the desired time zone and confirm.
14_991_Turbo_21.book Seite 124 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 125
Setting the date
The date and date format can be changed in the “ Date” menu.
Setting the date format
The date format can be adjusted.
Available setting options: –“ DD.MM.YYYY” –“ MM/DD/YYYY” –“ YYYY/MM/DD”
Setting the current date
The day, month and year can be set individually on vehicles without the navigation module.
Setting Daylight Saving Time
The vehicle clock can be configured to change to Daylight Saving Time.
Displaying time in stopwatch on dashboard
You can configure the stopwatch on the dashboard to display the time.
Setting units
You can select the units of measurement for vehicle displays such as the speed on the digital speedometer in the instrument panel, the temperature gauge in the air-conditioning displays and the tire pressure display on the multi-function display.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time” > “ Date” and confirm.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time” > “ Date”
2.“Format” and confirm.
3. Select the desired setting and confirm.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time” > “ Date” and confirm.
2. “Date”. in the main menu.
3. Set the desired date and confirm the setting.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time”
2.Select “ DST (+01:00)”
3.Confirm your selection.
Daylight Saving Time is activated.
Daylight Saving Time is deactivated.
1. Main menu “Vehicle” > “ Settings” > “ Date & Time”
2.Select “Time – Chrono” in the main menu.
3. Confirm your selection.
Time is displayed.
Time is not displayed.
1. Main menu “Vehicle” > “ Settings” > “ Units” and confirm.
14_991_Turbo_21.book Seite 125 Mittwoch, 9. April 2014 2:19 14