2014 PORSCHE 911 TURBO parking brake

152 Driving and Driving Safety
Releasing the parking brake
The electric parking brake can only be released when the ignition is switched on.1. Press the brake pedal. 2. Pull switch . The brake warning light on the instrument panel goes out.
Automatic electric parking brake release when driver’s intention to drive off is detected
If the engine is running, the driver’s door is closed and the driver’s safety belt is fastened, it is still possible to drive off normally even though the parking brake is on.The electric parking brake detects the driver’s intention to drive off and releases automatically.The warning light on the instrument panel goes out.
If the driver’s door is not closed or the driver’s safety belt is not fastened, the electric parking brake will not be released automatically when the driver attempts to drive off.The message “ Release parking brake” appears on the multi-function display in the instrument panel. The brake warning light on the instrument panel and the indicator light on the switch start to flash.
For information on warning messages on the multi-function display: fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Engaging the electric parking brake automatically
The electric parking brake engages if PDK selector-lever position D, R or M is selected when the vehicle is stationary and the driver’s door is opened. The brake warning light on the instrument panel and the indicator light on the switch light up. For information on warning messages on the multi-function display: fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Emergency braking function
If the vehicle cannot be stopped by conventional braking, you can decelerate sharply and stop the vehicle using the electric parking brake.fPress switch and keep it pressed.The message “ Emergency braking” appears on the multi-function display in the instrument panel. The brake warning light on the instrument panel and the indicator light on the switch start to flash.The emergency braking function is deactivated when you release the switch.
Emergency braking takes place with very high braking power. The following traffic may be endangered.fOnly use the emergency braking function in an emergency situation.fDo not use the emergency braking function to stop the vehicle when driving normally.
Brake warning light USA
Brake warning light Canada
If the electric parking brake could not be applied fully when the vehicle is stopped, the brake warning light on the instrument panel starts to flash.
For information on warning messages on the multi- function display: fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Brakes
fMake it a habit to check the operation of your brakes before driving.
Keep in mind that the braking distance increases very rapidly as the speed increases. At 60 mph (100 km/h), for example, it is not twice but four times longer than 30 mph (50 km/h). Tire traction is also less effective when the roads are wet or slippery.fTherefore, always maintain a safe distance from the car in front of you.
Severe decelerationWARNINGh
14_991_Turbo_21.book Seite 152 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 155
In heavy rain, while driving through water or after leaving a car wash, the braking action may be delayed and increased pressure may be required.fFor this reason, keep further back from the vehicle in front and “dry” the brakes by applying them at intervals. Make sure that the traffic behind you is not affected.
After a long drive over salted or gritted roads, a coating may form on the brake disks and pads that significantly reduces friction and therefore also braking effect.fEven though the brake disks consist of alloyed gray cast iron, they will unavoidably start to corrode if your vehicle is parked for an extended period. The brakes will tend to “rub” as a result.The nature, extent and effects of corrosion depend on the amount of time the vehicle was parked, whether road salt or grit was spread and whether grease-dissolving agents were used in car washes (not on vehicles with Porsche Ceramic Composite Brake).To prevent corrosion of the brake disks, “brake them dry” before parking the vehicle (not on vehicles with Porsche Ceramic Composite Brake).If braking comfort is noticeably impaired, we recommend that you have the brake system checked by experts at an authorized Porsche dealer.
fTo relieve the brake system on downhill stretches, change down to a lower gear in good time (engine braking).If engine braking is insufficient on steep stretches, operate the footbrake at intervals. Avoid continuous braking as it overheats the brakes and reduces the braking effect.
For information on brake fluid and checking the brake fluid level:fPlease see the chapter “BRAKE FLUID” on page 243.
New brake pads or linings
New brake pads have to be “broken in”, and therefore only attain optimal friction when the car has covered several hundred miles or km.The slightly reduced braking ability must be compensated for by pressing the brake pedal harder. This applies whenever the brake pads and/or brake disks are replaced.
A - Switch cruise control on/off 1 - Set/increase desired speed 2 - Reduce desired speed 3 - Interrupt (OFF) 4 - Return to set speed (RESUME)
Cruise Control
Cruise control maintains any selected speed between approx. 20–150 mph (30–240 km/h) without you having to use the accelerator.Cruise control is operated using the control stalk at the bottom left of the steering wheel.Downshifts are carried out to help maintain the pre-selected speed (especially when driving downhill).
Wet Brakes
Reduced Braking Efficiency
WARNINGh
WARNINGh
14_991_Turbo_21.book Seite 155 Mittwoch, 9. April 2014 2:19 14

164 Driving and Driving Safety
Driving off again
The vehicle can be driven off again after being stopped and speed and distance control will be resumed, depending on the operating state of the adaptive cruise control system.
Adaptive cruise control active
1. Press the control stalk on the steering wheel upwards (position 4, RESUME). 2. Press the accelerator pedal briefly. Your vehicle drives off again automatically.
Information
Your vehicle will not drive off if the vehicle detected in front is stationary.
Adaptive cruise control is ready
Automatic speed and distance control can only be resumed when your vehicle is moving.1. Drive off normally. 2. Press the control stalk on the steering wheel upwards (position 4, RESUME). orSet or change the desired speed.
Interrupting and resuming cruise control and distance control
Interrupting cruise control and distance control – OFF
fPress the brake pedal.orPress the control stalk on the steering wheel downwards (position 3, OFF). Adaptive cruise control is inactive.The desired speed that was stored and the desired distance are retained.
Resuming cruise control and distance control – RESUME
fPress the control stalk on the steering wheel upwards (position 4, RESUME). The vehicle accelerates to the desired speed that was stored unless a vehicle traveling in front is detected as driving slower than the desired speed and the distance from this vehicle is less than the desired distance that was set.The status display B changes from grey to orange.orPress the control stalk on the steering wheel upwards and keep it pressed (position 4, RESUME ). The vehicle accelerates in a more sporty driving style to the desired speed that was stored.
Information
If speed and distance control was interrupted by moving the control stalk to position 3 (OFF), it can only be resumed again when the vehicle is moving and no stationary objects are detected in front.
Messages on the multi-function display
If adaptive cruise control was deactivated automatically or if an action cannot be performed, a message to this effect in blue appears on the multi-function display.–“ ACC not available” Adaptive cruise control is not available, e.g. when maneuvering.–“ ACC not possible ABS/PSM intervention” Adaptive cruise control was deactivated because ABS or PSM intervened as a control mechanism.–“ Release parking brake” Adaptive cruise control was deactivated because the electric parking brake was activated.–“ ACC not possible Move gear lever to D/M ” Adaptive cruise control was deactivated because the PDK selector lever is not in position D or manual position M. –“ ACC not possible while stationary” The required action is not possible because your vehicle is stationary, e.g. when setting a desired speed.–“ ACC not possible Revs too high” Adaptive cruise control was deactivated because the engine-speed limit was reached in manual position M of the PDK selector lever/ shift paddles.–“ ACC not possible Gradient too steep” The desired distance or the desired speed cannot be set because the incline of the road is too steep.–“ ACC not possible Stationary object ahead ” The action is not possible because a stationary object was detected ahead.
14_991_Turbo_21.book Seite 164 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 165
–“ACC not possible Switch on PSM” Adaptive cruise control is not available because PSM was switched off.For information on Porsche Stability Management (PSM) :fPLEASE SEE THE CHAPTER “PORSCHE STABILITY MANAGEMENT (PSM)” on page 181.–“ ACC off” Adaptive cruise control was deactivated.– “ACC not possible Steering lock too large” The steering is turned too far.
General information
“Sport” and “Sport Plus” Mode
Adaptive cruise control regulates your driving more dynamically in “ Sport” and “Sport Plus” mode.
Exceptions for adaptive cruise control
Adaptive cruise control is not available in the following situations:– If the ignition is switched off.– When PSM is off.– If the driver’s door is opened and the driver’s safety belt is not fastened.– When parking or maneuvering in very tight spaces.– When the electric parking brake is activated.– If the PDK selector lever is in position N , R or P. – On upward or downward slopes of more than 15 %.
If one of these exception situations occurs when adaptive cruise control is switched on, adaptive cruise control will be switched off.A message to this effect appears on the multi-function display.
Warning messages
Overtake request when adaptive cruise control is active (ACC active)
If adaptive cruise control detects that braking assistance is required on the part of the driver, a warning signal sounds and the warning message “ Distance Please brake” appears on the multi- function display.
In this case, the braking power of the adaptive cruise control is not sufficient to prevent a collision.fBrake immediately.
Traffic situations in which vehicles cannot be reliably detected
The radar sensor for adaptive cruise control scans a narrow, cone-shaped area in front of your vehicle.Detection can be limited or unreliable, depending on the traffic situation and the size of the vehicle in front. The system may brake too late or unexpectedly.Stationary vehicles are not detected. The system cannot respond to stationary vehicles.fDrive with extreme care.fSlow down if necessary.
Inadequate braking power during automatic braking by the adaptive cruise control.
WARNINGh
14_991_Turbo_21.book Seite 165 Mittwoch, 9. April 2014 2:19 14

172 Driving and Driving Safety
Porsche Doppelkupplung (PDK)
Porsche Doppelkupplung (PDK) is a seven-speed transmission with an automatic and a manual selection mode.
In automatic selection mode (selector-lever position D), gear changing is automatic. You can change temporarily from automatic to manual mode using the shift buttons on the steering wheel.
In manual selection mode (selector-lever position M), you change gear using the shift buttons or shift paddles on the steering wheel or with the PDK selector lever.
You can change between selector-lever positions D and M as you wish while driving.
Information
fTake care not to operate the shift buttons on the steering wheel inadvertently in either automatic or manual mode, thereby triggering undesired gear changes.
Changing selector-lever position
The selector lever is blocked in the P position when the ignition is switched off.
When the ignition is switched on, the selector lever can be moved from position P and N only when the release button is pressed, and when the brake pedal is pressed.
Release button
The release button ( arrow) in the selector lever prevents the gear from being changed unintentionally.The release button must be pressed when shifting to position R or P.
Starting
The engine can be started only if the brake pedal is depressed and the selector lever is in position P or N.
Driving off
fOnly select the desired position for driving off ( D, M or R) when the engine is idling and the brake pedal is pressed.fSince the vehicle crawls when in gear, do not release the brake until you are ready to drive off.
Driving off on hills
The Drive-Off Assistant assists the driver when driving off on hills. The vehicle is held on the slope for a short time during the change from the brake pedal to the accelerator to facilitate driving off immediately after the brake is released.fPlease see the chapter “HOLD FUNCTION: DRIVE-OFF ASSISTANT, STANDSTILL MANAGEMENT” on page 184.
Stopping
fFor a brief stop, e.g. at traffic lights, leave the selector lever in drive position and hold the vehicle with the brake pedal.fDo not hold the vehicle on a slope using the accelerator. Use the brake pedal or the electric parking brake instead.fBefore leaving the vehicle, always apply the electric parking brake and move the selector lever to position P.
Parking
fGo easy on the accelerator!fWhen parking or maneuvering in a small space, control the speed by careful use of the footbrake.
14_991_Turbo_21.book Seite 172 Mittwoch, 9. April 2014 2:19 14

174 Driving and Driving Safety
Selector-lever Positions
P – Parking lock
fEngage parking lock only when the vehicle is stationary.If selector-lever position P is flashing in the instrument panel, the parking lock is not engaged. The vehicle can roll away.Shift again from selector-lever position R to P.fActivate the electric parking brake and then engage the parking lock.If selector-lever position P is flashing in the instrument panel, the parking lock is not engaged. The vehicle can roll away.Shift again from selector-lever position R to P.
Vehicles without Porsche Entry & Drive: The ignition key can only be removed in selector- lever position P.
R – Reverse gear
fSelect only if the vehicle is stationary and the brake is applied.
N – Neutral
Selector-lever position N must be selected for towing or in car washes, for example.fOnly select the desired position for driving off ( D, M or R) when the engine is idling and the brake pedal is pressed.
D – Automatic selection mode
Select position D for “normal” driving. The gears are shifted automatically according to the accelerator position and speed.
Depending on the way the vehicle is driven (economical, comfortable or sporty driving style) and on the resistance (e.g. uphill), the gear-changing points are shifted towards higher or lower engine-speed ranges.The accelerator position, driving speed, engine speed, longitudinal and lateral acceleration and the road profile all have an influence on the gear-changing characteristic.
Unwanted upshifts, e.g. when entering bends, are prevented by swiftly releasing the accelerator pedal.
Depending on lateral acceleration, upshifts on bends are not made until the engine-speed limit is reached.
When you brake, and depending on the amount of deceleration, the PDK transmission changes down earlier.For subsequent cornering, the correct gear is engaged when pressure is applied to the brakes before the bend. The bend is taken in the right gear, and when you accelerate out of the bend you do not have to change down.
With a sporty driving style, downshifts are already initiated when the brake pedal is touched lightly. This further enhances a dynamic driving style.
The PDK transmission temporarily changes to the sportiest gear-changing map, i.e. to the highest possible gear-changing points, if the accelerator pedal is pressed quickly. The transmission accordingly shifts down immediately by one or two gears (temporary downshift).
The transmission no longer selects 7th gear at very high driving speeds.
However, if necessary, the gear can be selected manually.
Upshifts and downshifts are avoided as far as possible when PSM is active. In the case of high wheel slip when PSM is switched off, upshifts are prevented until slip is no longer detected.
Driving in coasting mode
Through attentive driving, fuel can be saved in coasting mode. The vehicle rolls with the engine disengaged and at idle speed without engine braking effect.
Preconditions for automatic coasting mode – Driving in selector lever position D – Coasting mode is switched on.Indicator light on the button is off.– Sport and Sport Plus modes are switched off– PSM is active– Cruise control is not active– Engine, transmission and battery are at operating temperature– Calm/economic driving style– Slight uphill or slight downhill gradientsfSlowly take your foot off the accelerator.
The engine is disengaged and runs at idle speed. The vehicle rolls with no engine braking effect. Coasting mode is recognizable by the idle speed indicated on the tachometer.
Information
In the case of a sporty driving or when swiftly releasing the accelerator pedal, coasting mode is suppressed to allow targeted use of the engine braking effect. On more pronounced uphill gradients, “coasting” is also prevented as the coasting phases are very short due to the gradient and no significant fuel savings can be achieved. On more pronounced downhill gradients, coasting
14_991_Turbo_21.book Seite 174 Mittwoch, 9. April 2014 2:19 14

184 Driving and Driving Safety
HOLD function: Drive-Off
Assistant, Standstill Management
The HOLD function, as an assistance function, assists the driver when stopping and driving off on upward slopes.The vehicle is automatically prevented from rolling back away from the desired direction of travel.When the HOLD function is active, the indicator light on the instrument panel comes on.
The vehicle is stopped and prevented from rolling back away from the desired direction of travel even without pressing the brake.
Information
The HOLD function is not available if the PDK selector lever is in position P and N.
If the PDK selector lever is moved while the HOLD function is active, the HOLD function is deactivated.
If the driver’s safety belt is unfastened and the driver’s door is opened while the HOLD function is active, the electric parking brake is activated automatically.
For information on the electric parking brake:fPlease see the chapter “ELECTRIC PARKING BRAKE” on page 151.
The limits set by the physics of driving cannot be overcome, even with the HOLD function. Responsibility for driving off on upward slopes is still the driver’s, despite the HOLD function.Assistance by the HOLD function is not always guaranteed when stopping and driving off on a slippery surface (e.g. on icy or loose surfaces). In this case, the vehicle can slip.fAlways adjust your driving style to the driving conditions and vehicle load. Use the footbrake if necessary.
If the Drive-Off Assistant is not functioning, the driver cannot be assisted when driving off on hills.fHold the vehicle with the footbrake.
If the vehicle comes to a standstill on a steep uphill gradient without operation of the footbrake by the driver, this may result in a certain roll-back before the vehicle is held by the HOLD function. In this situation, the roll-back can be reduced by pressing the footbrake.fAssist holding of the vehicle by increasing the braking force with the footbrake.
Information
When the HOLD function is active, the brake pedal may feel different and you may hear hydraulic noises.
This behavior is normal for the system. It is not a fault.
ABS Brake System
(Anti-lock Brake System)
In spite of the advantages of ABS, it is still the driver’s responsibility to adapt his driving style and maneuvers in line with road and weather conditions, as well as the traffic situation.
The increased safety that is provided should not induce you to take greater risks with your safety. The limits set by the physics of driving cannot be overcome, even with ABS.Risk of accidents due to inappropriate speed cannot be reduced by ABS.
ABS helps provide:
– Full steering control The vehicle remains steerable– Good driving stability No skidding due to locked wheels– Optimum braking distance Shorter stopping distance in most cases– Prevention of wheel locking No flat spots on the tires
Limits of HOLD Function
Drive-Off Assistant Not Working
Vehicle Roll-back
WARNINGh
CAUTIONh
CAUTIONh
Loss of control over the vehicleWARNINGh
14_991_Turbo_21.book Seite 184 Mittwoch, 9. April 2014 2:19 14

Parking 207
ParkAssist
When the driver is parking and maneuvering the vehicle, ParkAssist indicates the distance between the vehicle and a large obstacle by means of signal tones.fOn vehicles with front and rear sensors:For information on the ParkAssist visual display, please refer also to the section “PARKASSIST” in the operating instructions for the Porsche Communication Systems PCM/CDR.
ParkAssist is activated automatically when reverse gear is selected and the ignition is on.
If the vehicle has front ParkAssist, this also issues an automatic warning when the distance between the vehicle and an obstacle in front is less – than approx. 40 in./100 cm (acoustically) and approx. 32 in./80 cm (visually).
A warning signal sounds when – the distance between the vehicle and an obstacle at the rear is less than approx. 71 in./180 cm.The ParkAssist visual display appears on the central screen of the Porsche communication system.
Front and rear ParkAssist is not activated: – At a speed of more than approx. 9 mph (15 km/h).– When the electric parking brake is activated.– When the ParkAssist has been switched off with button A in the overhead console with the ignition switched on. The indicator light in button A lights up.
Responsibility for parking and for assessing the risk to persons, children, pets, and small objects around the vehicle lies completely with the driver. fMake sure that no persons (especially small children), animals or obstacles are within the maneuvering area. fIf the continuous tone sounds, stop and do not move your vehicle further in that direction.
Ultrasound sensors
Sensors
The ultrasound sensors A in the rear bumper and the sensors A in the front bumper (depending on vehicle equipment) measure the distance to the closest obstacle:– Range behind the vehicle: approx. 71 in. (180 cm)– Range at the side of the vehicle: approx. 24 in. (60 cm)– Range in front of the vehicle: approx. 47 in. (120 cm)
Obstacles cannot be detected in the “blind” sensor area (above and below the sensors, e.g. objects hanging down or close to the ground).
ParkAssist LimitsWARNINGh
14_991_Turbo_21.book Seite 207 Mittwoch, 9. April 2014 2:19 14