2014 PORSCHE 911 TURBO performance

154 Driving and Driving Safety
fBefore descending a steep grade, reduce speed and shift the transmission into a lower gear to control speed. fDo not “ride the brakes” by resting your foot on the pedal when not intending to apply brake pressure.fDo not hold the pedal down too long or too often. This could cause the brakes to overheat and lose braking power.
Brake booster
The brake booster assists braking only when the engine is running.
When the car is moving while the engine is not running, or if the brake booster is defective, more pressure on the brake pedal is required to bring the car to a stop.
Moisture, road salt or grit on brakes affects braking. Brakes will dry after a few cautious brake applications.
Driving through water may reduce the traction. Moisture on brakes from road water, car wash, or a coating of road salt or grit may affect braking efficiency.fCautiously apply brakes to test and dry the brakes after exposure to road water, etc.
The brake booster is ready for operation only while the engine is running. If the engine is switched off or there is a defect in the brake booster, much greater force has to be applied to the pedal when braking. fVehicles with defective brakes must not be towed and must be transported on a flat bed.
For information on towing:fPlease see the chapter “TOWING” on page 278.
Brake wear
Your car has excellent brakes, but they are still subject to wear. The rate at which they wear depends on how the brakes are used.fHave the brake system inspected at the intervals recommended in your Maintenance Booklet.
Brake system warning light
You can check the functionality of the brake system warning light by switching the ignition to the “On” position (position 1) and verifying that the warning light illuminates.
A warning message will be displayed on the multi- purpose display of the instrument panel if the brake pads are worn, excessively.fDo not continue to operate the vehicle.Have your authorized Porsche dealer inspect or replace the brake pads.
For information on warning messages on the multi-purpose display:fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Brake pads and brake disks
Wear on the brake pads and brake disks depends to a great extent on the driving style and the conditions of use and therefore cannot be expressed in actual miles on the road.
The high-performance brake system is designed for optimal braking effect at all speeds and temperatures.
Certain speeds, braking forces and ambient conditions (e.g. temperature and humidity) can therefore cause the brakes to “squeal”.
Unsuitable or incorrectly installed floor mats or objects can obstruct the movement of the brake pedal or prevent application of the brake pedal.fDo not obstruct the pedal travel with floor mats or other objects.
Riding the Brakes
Wet Brakes
WARNINGh
WARNINGh
Loss of Braking PowerWARNINGhBrake wear warning message USA
Brake wear warning message Canada
Obstructed Brake PedalWARNINGh
14_991_Turbo_21.book Seite 154 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 175
is suppressed because here, the vehicle does not slow down, despite the engine overrun torque and no fuel is consumed in this driving situation due to utilization of the overrun shut-off.
Ending coasting mode/utilizing engine braking effect
fPress the accelerator or brake pedalor Operate a shift paddle or a shift button or Shift gear using the selector lever.
Initiating coasting mode manually
– Driving in selector lever position D or driving in selector lever position M
When coasting mode is suppressed, e.g. in the case of sporty driving, sudden release of the accelerator pedal or excessively low engine temperature, coasting mode can be initiated manually.fTake your foot off the accelerator pedal and shift past the highest possible gear with the shift paddle, one of the shift buttons, or with the selector lever.
Switching coasting mode on and off using the Auto Start Stop button
Switching off
fPress button . The indicator light on the button lights up.Coasting mode is switched off and automatic stopping of the engine is suppressed.
Switching on
fPress button . The indicator light on the button goes out.Coasting mode is switched on and the engine is automatically stopped when the vehicle stops.
“Sport” mode activated
The PDK transmission switches to a sporty gear- changing map and shortens the shifting times.A sporty driving style is recognized more quickly and the gear-changing speeds are adapted to driving performance.
Braking downshifts are initiated earlier. Downshifts occur for small decelerations, even at higher revs.
“Sport Plus” mode activated
In “Sport Plus” mode, the PDK transmission changes to a shift program designed for driving on race circuits. 7th gear is not selected.The gear-changing performance is enhanced significantly again compared with “Sport” mode.fPlease see the chapter ““SPORT” AND “SPORT PLUS” MODE” on page 188.
Driving off with Launch Control
Launch Control allows you to achieve maximum acceleration from standstill.
Launch Control is designed to be used in a controlled environment on closed circuit driving courses where no vehicle cross traffic or pedestrian traffic is present.fUse Launch Control only if conditions permit it to be applied in a safe manner.fDo not use Launch Control if there is a possibility it could endanger other persons.Such a possibility exists if you cannot see that you have a clear road with no possibility of cross traffic in your intended direction of driving.
Information
Stress on components increases dramatically when starting with maximum acceleration in comparison with normal driving off.
Preconditions: – Launch Control should only be used when the engine has reached operating temperature.–“ Sport Plus” mode must be switched on (indicator light on the button comes on and SPORT PLUS appears on the digital speedometer or on the steering wheel).1. Press the brake with your left foot. 2. Quickly press the accelerator down fully (kickdown activated) and hold it.The engine speed will level off at around 5,500 rpm.“ Launch Control activated” is displayed on the multi-function display.Depending on equipment, the “LAUNCH CONTROL” logo appears on the steering wheel.3. Release the brake within a few seconds.
Remaining stationary for a long time with LAUNCH CONTROL can lead to overloading of the transmission.To protect the transmission, the engine power is then reduced and the LAUNCH CONTROL process is cancelled.
In order to drive off, the accelerator must first be fully released.
Endangering Other Road Users
WARNINGh
14_991_Turbo_21.book Seite 175 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 179
Transmission and Chassis Control Systems
Your Porsche sports car features a complex integrated system made up of all control systems acting in power transmission and in the chassis.
All control systems are networked with the aim of combining the best possible driving performance with maximum safety.
The following systems are involved, depending on equipment:
System/designation Scope
PTM
Porsche Traction Management
– Active allwheel drive with electronically regulated map-controlled multi-plate clutch
PSM
Porsche Stability Management
– Driving stability control – Anti-lock brake system (ABS)– Brake system prefilling– Brake booster (Hydraulic Brake Assist)– Automatic brake differential (ABD)– Anti-slip control (ASR)– Engine drag torque control (MSR)– Steering torque recommendation– HOLD function: Standstill management
PASM
Porsche Active Suspension Management
– Shock absorber system with adaptive, continuous shock absorber control
PDCC
Porsche Dynamic Chassis Control
– Active chassis control system to stabilize roll tendency of vehicle body when driving
PTV Plus
Porsche Torque Vectoring Plus
– Laterally dynamic braking intervention for more agile cornering – Fully-variable electronically controlled rear differential lock
14_991_Turbo_21.book Seite 179 Mittwoch, 9. April 2014 2:19 14

180 Driving and Driving Safety
Despite the advantages of transmission and chassis control systems, it is still the driver’s responsibility to adapt his driving style and maneuvers in line with road and weather conditions, as well as the traffic situation.
The increased safety that is provided should not induce you to take greater risks with your safety. The limits set by the physics of driving cannot be overcome.These systems cannot reduce the risk of accidents due to inappropriate speed.fAdapt your driving style, maneuvers and speed to the road and weather conditions, as well as the traffic situation.
Porsche Traction Management
(PTM)
Porsche Traction Management is an active allwheel control system designed to influence longitudinal and lateral dynamics. It is closely linked with the Porsche Stability Management (PSM) system.
The permanently driven rear axle enhances the vehicle’s sporty features. Drive power is distributed fully variably to the front axle, depending on the driving situation.
In conjunction with PSM, the PTM system ensures perfect distribution of power among all four wheels in every driving situation. This improves traction and driving stability and ensures the same high level of agility and dynamic response.
In spite of the advantages of PTM and four-wheel drive, it is still the driver’s responsibility to adapt his driving style and maneuvers in line with road and weather conditions, as well as the traffic situation.
The increased safety that is provided should not induce you to take greater risks with your safety. The limits set by the physics of driving cannot be overcome, even with PTM or four-wheel drive.Risk of accidents due to inappropriate speed cannot be reduced by PTM or four-wheel drive.
Advantages of PTM
– Clearly perceptible improvement in traction, driving stability and steering ability of the vehicle.– Vehicle is more manageable when driven at its performance limits.– Improved straight-ahead tracking and greater stability.– More sporty vehicle setup while making full use of all the advantages of four-wheel drive.– ASR, ABD and PTV Plus further enhance traction for all wheels.
For information on ASR and ABD:fPlease see the chapter “PORSCHE STABILITY MANAGEMENT (PSM)” on page 181.
For information on current torque distribution between front and rear wheels in the multi-function display:fPlease see the chapter “ALLWHEEL MENU” on page 114.
Driver ResponsibilityWARNINGh
Loss of control over the vehicleWARNINGh
14_991_Turbo_21.book Seite 180 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 183
When PSM is switched off, PSM support is no longer provided in critical driving situations outside the ABS control range. fPSM should always be switched on during “normal” driving.
However, it may be a good idea to switch off PSM temporarily in exceptional situations:– On a loose surface and in deep snow.– When “rocking the vehicle free”.
Information
The vehicle retains its enhanced braking readiness through prefilling of the brake system even when PSM is switched off.
When PSM is switched off, wheel-specific brake interventions and the anti-slip control system (ASR) are also switched off.The automatic brake differential (ABD) remains on.
Switching PSM back on
fPress button . PSM is active immediately.The indicator light on the button and the PSM OFF warning light on the instrument panel go out.The message “ PSM on” appears on the multi-function display in the instrument panel.
“Sport Plus” mode
A sportier setup is obtained when “ Sport Plus” mode is switched on.PSM interventions occur later than in Normal mode. The vehicle can be maneuvered with greater agility at its performance limits, without having to dispense with the assistance of PSM in emergency situations. This helps to achieve optimal lap times, particularly on race circuits and on a dry road surface.
PSM warning light
– The PSM warning light on the instrument panel lights up for a lamp check when the ignition is switched on.– The light indicates a control operation, even when PSM is switched off, e.g. brake control in the event of one-sided wheel spin.– The light – in conjunction with the multi-function display – indicates a fault.The warning message “ PSM failure Consult a workshop Adapted driving permitted ” appears on the multi-function display in the instrument panel.
For information on warning messages on the multi-function display:fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.fAdapt your driving style according to the changed conditions.fContact an authorized Porsche dealer.
Towing
For information on towing:fPlease see the chapter “TOWING” on page 278.
No PSM assistanceWARNINGh
14_991_Turbo_21.book Seite 183 Mittwoch, 9. April 2014 2:19 14

188 Driving and Driving Safety
Dynamic Engine Mounting (PADM)
On vehicles with Sport Chrono package
Dynamic Engine Mounting with variable damping is a system designed to enhance both driving dynamics and driving comfort. Depending on the driving situation, the ideal mounting rigidity and damping is automatically set in the range between an rigid engine-to-body connection (increase in driving dynamics) and decoupling of the engine from the body (increase in driving comfort).
“Sport” mode
When “ Sport” mode is switched on, a more rigid engine-to-body connection is achieved for a sporty driving style.
“Sport Plus” mode
When “ Sport Plus” mode is switched on, an optimal engine-to-body connection is achieved for driving on race circuits.
Warning message
Dynamic engine mounting faults are indicated by a warning message on the multi-function display.fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
“Sport” and “Sport Plus” mode
The selectable chassis settings mean that the vehicle can offer various modes for a sportier overall setup.The “ Sport” mode pushes the control systems more in the direction of greater emotionality and performance during every day driving.
In “ Sport Plus” mode, maximum performance is set for race-circuit-like driving:– In “ Sport Plus” mode: PASM (Porsche Active Suspension Management) is automatically changed to “ Chassis Normal” or “Chassis Sport” mode. – In “ Sport Plus” mode: Like PASM, PDCC is switched to the corresponding “ Sport” mode, whereby the rolling movements of the vehicle are reduced further, depending on the selected mode.– The PDK transmission switches to a sporty gear-changing map and shortens the gear shifting times when Sport mode is activated. Gear changes take place faster.– The electronic accelerator pedal reacts sooner, and the engine is more responsive to throttle inputs. When Sport mode is switched on and the vehicle is traveling at a speed of less than 40 km/h (25 mph), this function is activated only after the driver has floored the accelerator pedal or released it briefly.– The rpm limiter characteristic is “harder”. In other words: the engine is immediately throttled when the performance limits are reached (only in manual selection mode on vehicles with PDK).
– PSM (Porsche Stability Management) control is more sporty in “ Sport Plus” mode. PSM interventions are later than in Normal mode. The driver can maneuver the vehicle with greater agility at its performance limits, without having to dispense with the assistance of PSM in emergency situations. This helps to achieve optimal lap times, particularly on race circuits with a dry road surface.– PADM changes to more sporty maps for the dynamic engine mountings to achieve a stiffer engine-to-body connection.In “ Sport” for a sporty driving style, in “ Sport Plus” mode for race-circuit-like driving. – PTV Plus changes to a more dynamic map when “ Sport Plus” is switched on. – The dynamic cornering light reacts more spontaneously to steering angle changes.– The sports exhaust system is be switched to a sound-optimized mode, but can be switched off separately via the button.The Auto Start Stop function and coasting mode are deactivated.fPlease read the relevant chapters.
Overboost function
On vehicles with Sport Chrono package
When “ Sport” or “Sport Plus” mode is switched on and the accelerator is fully pressed, the boost pressure is temporarily increased by approx. 2 psi (0.15 bar) in the medium engine-speed range and the maximum torque increases.
For information on the torque display:fPlease see the chapter “PERFORMANCE MENU” on page 116.
14_991_Turbo_21.book Seite 188 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 189
Switching “Sport” mode on and off
fPress button . When “ Sport” mode is switched on, the indicator light on the button lights up.The word “ SPORT” appears on the digital speedometer or on the steering wheel, depending on vehicle equipment.
A sporty gear-changing map is enabled and the gear shifting times are shorter for the PDK transmission.
A sporty driving style is recognized more quickly and the gear-changing speeds are adapted to driving performance.
Braking downshifts are initiated earlier. Downshifts occur for small decelerations, even at higher revs.
Switching “Sport Plus” mode on and off
fPress button .When “ Sport Plus” mode is switched on, the indicator light on the button lights up.The words “ SPORT PLUS” appear on the digital speedometer or on the steering wheel, depending on vehicle equipment.
In “ Sport Plus” mode, the PDK transmission changes to a shift program designed for driving on race circuits. 7th gear is not selected.
“Sport Plus” and “PASM Chassis Sport” modes
Switching “ Sport Plus” mode on and off simultaneously activates and deactivates the “ PASM Sport” mode. Switching “ Sport” mode has no influence on the PASM mode.
The PASM mode can be switched manually if you want to use the characteristics of “ Sport” or “ Sport Plus” mode, but prefer a more comfortable chassis setup.fPress button (repeatedly).The indicator light for the selected chassis setup on the button lights up.fPlease see the chapter “PORSCHE ACTIVE SUSPENSION MANAGEMENT (PASM)” on page 185.
14_991_Turbo_21.book Seite 189 Mittwoch, 9. April 2014 2:19 14

Maintenance and Car Care 221
Radiator fan, engine compartment blowers
The engine-compartment blowers are mounted under the engine compartment lid.After the engine is switched off, the engine compartment temperature is monitored for approx. 30 minutes.During this period, and depending on temperature, the engine-compartment blowers may continue to run or start to run.fCarry out work in this area only with the engine off and exercise extreme caution.
The radiators and radiator fans are in the front of the vehicle.The radiator fans in the front of the vehicle may be operating or unexpectedly start operating when the engine is switched on.fCarry out work in these areas only with the engine switched off.fTake great care to ensure that parts of the body, items of clothing or jewelery cannot be drawn in by the radiator fan, engine-compartment blower, drive belt or other moving parts.
Measurements on test stands
Performance test
Performance tests on roller-type test stands are not approved by Porsche.
Brake tests
Brake tests must be performed only on roller-type test stands.
The following limit values must not be exceeded on roller-type test stands: – Test speed 4.7 mph (7.5 km/h)– Test duration 20 seconds
Testing the electric parking brake
Electric parking brake tests on the brake test stand must only be performed with the ignition switched on and with the Porsche Doppelkupplung selector lever in position N. The vehicle switches automatically to brake test stand mode, in which the electric parking brake can be tested.The message “ Electric parking brake in service mode ” appears on the multi-function display in the instrument panel.
Balancing wheels on the vehicle
During finish balancing of the wheels, the entire vehicle must be lifted and the wheels must be free to turn.
Engine Oil
It is important to perform oil changes regularly in accordance with the intervals specified in your Maintenance Schedule .
Engine oil consumption
It is normal for your engine to consume oil. The rate of oil consumption depends on the quality and viscosity of oil, the speed at which the engine is operated, the climate, road conditions as well
as the amount of dilution and oxidation of the lubricant.
If the vehicle is used for repeated short trips, and consumes a normal amount of oil, the engine oil measurement may not show any drop in the oil level at all, even after 600 miles (1000 km) or more. This is because the oil is gradually becoming diluted with fuel or moisture, making it appear that the oil level has not changed. The diluting ingredients evaporate out when the vehicle is driven at high speeds, as on an expressway, making it then appear that oil is excessively consumed after driving at high speeds.
If the conditions you drive your vehicle in are dusty, humid, or hot, the frequency of the oil change intervals should be greater.
If the vehicle is driven at a high rate of speed, climatic conditions are warm, and the load is high, the oil should be checked more frequently, as driving conditions will determine the rate of oil consumption.– The engine in your vehicle depends on oil to lubricate and cool all of its moving parts. Therefore, the engine oil should be checked regularly and kept at the required level.– Make it a habit to have the engine oil level checked with every refueling.– The oil pressure warning light is not an oil level indicator. The oil pressure warning light indicates serious engine damage may be occurring when lit, if engine rpm is above idle speed.
Radiator Fans, Engine Compartment Blowers
WARNINGh
14_991_Turbo_21.book Seite 221 Mittwoch, 9. April 2014 2:19 14