2014 PORSCHE 911 TURBO check engine light

Instrument Panel and Multi-Function Display 93
F – Engine oil pressure gauge
The oil pressure is controlled as required and should be at least 51 psi (3.5 bar) at an engine speed of 5000 rpm.
The engine oil pressure varies depending on the engine speed, oil temperature and engine load.
If oil pressure drops abruptly and a message is displayed on the multi-function display when the engine is running or while driving:fStop immediately in a suitable place.fSwitch off the engine.fCheck whether there is an obvious oil leak on or under the car.fSelect “ Oil measurement” on the multi- function display.fPlease see the chapter “DISPLAY AND MEASUREMENT OF THE ENGINE OIL LEVEL” on page 101.fAdd engine oil if necessary.
Risk of engine damage.fDo not continue driving if there is an obvious oil leak.fDo not continue driving if the warning message appears even when the oil level is correct.fHave the fault corrected at an authorized Porsche dealer.
G – Reset button for trip counter display/ brightness setting for instrument lighting
Resetting trip counter display
fPress rotary switch G for approx. 1 second. The trip counter display is reset to “0”.
Adjusting brightness of instrument lighting
For information on adjusting the brightness of the instrument lighting:fPlease see the chapter “INTERIOR/READING LIGHTS” on page 84.
H – Odometer
The displays for the total mileage and individual trips are integrated in the speedometer on the instrument panel.
The upper display counts the total mileage, the lower display shows individual trips.
After exceeding 6,213 miles or 9,999 kilometers, the trip counter returns to 0.
I – Digital speedometer
The digital speedometer I is integrated in the tachometer on the instrument panel.
J – Upshift prompt indicator
The consumption-oriented shift indicator to the right of the digital speed display on the tachometer helps you to develop a fuel-saving driving style. The upshift indicator lights up – prompting you to shift up to the next-higher gear – depending on the selected gear, engine speed and accelerator pedal position.fChange to the next-higher gear when the upshift indicator lights up.
NOTICE
14_991_Turbo_21.book Seite 93 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 95
Battery/Alternator
The warning message “Generator fault Park vehicle safely ” will appear on the multi-function display in the instrument panel if the vehicle electrical system voltage drops significantly.fStop at a safe place and switch the engine off.
For information on warning messages on the multi-function display:fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Possible causes
– Defect in the battery charging system– Broken drive belt
Risk of engine damage.
The engine cooling does not function if the drive belt is torn.fDo not continue driving.fHave the fault corrected.fPlease contact an authorized Porsche dealer.
Check Engine
(Emission Control)
Warning light
The emission control system detects malfunctions that could cause increased pollutant emissions or consequential damage etc. well in advance.Faults are indicated by the warning light on the instrument panel which then either lights up continuously or flashes.The faults are recorded in the control unit’s fault memory.
The warning light on the instrument panel lights up when the ignition is switched on as a lamp check and goes out approx. 1 second after the engine starts.
The warning light on the instrument panel flashes to indicate operating states (e.g. engine misfiring) which may cause damage to certain parts of the emission control system.fIn this case, immediately reduce the engine load by easing off the accelerator pedal.
In order to avoid consequential damage to the engine or the exhaust-gas cleaning system (e.g. catalytic converter):fPlease contact an authorized Porsche dealer.
Risk of damage to the emission control system.
If the warning light on the instrument panel continues flashing even when you have eased off the accelerator pedal, the emission control system may overheat.fStop as soon as possible in a safe place.Make sure that combustible materials, such as dry grass or leaves, cannot come into contact with the hot exhaust system.fSwitch off the engine.fHave the fault corrected at an authorized Porsche dealer.
Acoustic Signals
A speaker in the instrument panel generates acoustic signals.The warning message “ Instrument cluster/ Park Assist audio fault Service required ” will appear on the multi-function display in the instrument panel if a speaker fault occurs.The speaker cannot generate acoustic signals.fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Warning message
NOTICE
NOTICE
14_991_Turbo_21.book Seite 95 Mittwoch, 9. April 2014 2:19 14

Instrument Panel and Multi-Function Display 129
Overview of Warning and Information Messages
If a warning message appears, always refer to the corresponding sections in this Owner’s Manual. Warning messages are issued only if all measurement prerequisites are met. Therefore, check all fluid levels regularly – in particular, always check the engine oil level before refueling.
Warning and information message categories
fVisit or consult an authorized Porsche dealer immediately.
fVisit an authorized Porsche dealer at the next opportunity.
fVisit an authorized Porsche dealer at the next opportunity or remedy yourself.
Red System failure or warning
Yellowfault or system failure warning
WhiteInformation/message
Light in instrument panel
Warning and information message on the multi-function display Meaning/Action required
Oil press. too low Park vehiclesafely
Stop immediately in a suitable place and switch engine off. Do not continue driving. Select “Oil measurement” on the multi-function display. Add engine oil if necessary.Do not continue driving if the warning message is displayed despite the oil level being correct.Have the fault corrected at an authorized Porsche dealer.
Oil pressure measurement faultDriving permittedConsult a workshop
Have the fault corrected at an authorized Porsche dealer.
Oil temperature too high Reduce load Switch engine off and let it cool. Check oil level and, if necessary, add oil.
Oil temperature indicator faultConsult a workshopDriving permitted
Have the fault corrected at an authorized Porsche dealer.
Oil level measurement faultConsult a workshopDriving permitted
Have the fault corrected at an authorized Porsche dealer.
No information about oil levelavailable at present
The oil level can be checked after waiting for approx. 1 minute with the vehicle parked on a level surface and the engine at operating temperature. If the rear luggage compartment lid is opened when the engine is cold (e.g. to top up engine oil), the oil level cannot be displayed for a certain time.
14_991_Turbo_21.book Seite 129 Mittwoch, 9. April 2014 2:19 14

130 Instrument Panel and Multi-Function Display
Oil level minimum reachedRefill oil
Top up engine oil immediately.
Oil level below min. Refill oil at once Do not drive on
Top up engine oil immediately.
Oil level above maximumConsult a workshopDriving permitted
Visit an authorized Porsche dealer at the next opportunity and have the oil drained to the correct level.
Gauge moves to maximum markEngine too hot Park vehicle to cool down Coolant or engine oil temperature is too high. Switch off engine and let it cool.Check coolant or engine oil level. If necessary, top up coolant / engine oil.
Refill coolant Observeengine temperature
Check coolant level. Add coolant if necessary.
Gauge moves to maximum markRefill coolant immediatelyDo not drive on
Switch engine off and let it cool. Check coolant level. Add coolant if necessary.
Cooling system faultConsult a workshopService required
Have the fault corrected at an authorized Porsche dealer.
Coolant temp indicator faultDriving permittedConsult a workshop
Have the fault corrected at an authorized Porsche dealer.
Engine fan failure Avoid full loadDriving permitted
Have the fault corrected at an authorized Porsche dealer.
Generator fault Park vehiclesafely
Stop in a suitable place and switch engine off. Do not continue driving.Have the fault corrected at an authorized Porsche dealer.
Low battery Start the engine and run for extended period
Start the engine immediately so that the battery can be charged.
Light in instrument panel
Warning and information message on the multi-function display Meaning/Action required
14_991_Turbo_21.book Seite 130 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 147
Ignition lock position 0 – Ignition off (initial position)
The engine and ignition are off in ignition lock position 0. The ignition key can be removed in this position.
Ignition lock position 1 – Ignition on
fTurn ignition key to position 1.
All electrical equipment can be switched on. The warning lights on the instrument panel light up for a lamp check.fPlease see the chapter “INSTRUMENT PANEL USA MODELS” on page 90.
If a load is not switched on for 10 minutes after switching on the ignition, the ignition must be switched on again. Turn the ignition key to ignition lock position 0 (initial position) first.
The ignition key cannot be removed when the ignition is switched on or when the engine has been started.
To remove the ignition key: fStop the vehicle.fMove PDK selector lever to position P.fSwitch ignition off.fRemove the ignition key.
Ignition lock position 2 – Start engine
fTurn ignition key to ignition lock position 2.
The key is reset automatically from position 2 to position 1 when you start the engine.
Emergency operation with Porsche Entry & Drive
Interference in radio transmission between the vehicle and ignition lock or a discharged ignition lock battery can disable the Porsche Entry & Drive comfort function.
If this happens, the control unit can be removed from the ignition lock and the vehicle can be started using the ignition key.
For information on removing the control unit from the ignition lock: fPlease see the chapter “EMERGENCY OPERATION – UNLOCKING THE IGNITION KEY/CONTROL UNIT” on page 28.
Starting and Stopping the Engine
The immobilizer can be deactivated and the engine started only using an authorized ignition key.fPlease see the chapter “IMMOBILIZER” on page 217.
Exhaust gas contains colorless and odorless carbon monoxide (CO), which is toxic even in low concentrations. Carbon monoxide can cause unconsciousness and even death if inhaled.fNever start or let the engine running in an enclosed, unventilated area. It is not recommended to sit in your car for prolonged periods with the engine on and the car not moving.
Exhaust fumes and the exhaust system are very hot when the engine is running. The exhaust system remains hot for some time after the engine is turned off.fDo not park or drive your vehicle where combustible materials, such as dry grass or leaves, can come into contact with the hot exhaust system.fIf your car catches on fire for any reason, call the fire department. Do not endanger your life by attempting to put out the fire.
Exhaust Gas
Exhaust System Fire Hazard
WARNINGh
WARNINGh
14_991_Turbo_21.book Seite 147 Mittwoch, 9. April 2014 2:19 14

150 Driving and Driving Safety
Information
The engine will start automatically in certain situations, e.g. if the vehicle starts rolling, if air conditioning causes reduced comfort, or if the brake vacuum is reduced.The engine is stopped again automatically if the preconditions for stopping the engine automatically are then met again.
Exceptions for the Auto Start Stop function
The Auto Start Stop function is deactivated e.g.: – When Sport mode is activated.– When PSM is off.– In maneuvering mode.– When A/C MAX mode is activated.– When the “Windshield defrost” function is active. – At altitudes above approx. 9,843 ft. (3,000 meters)
For information on switching on and off the Auto Start Stop function:fPlease see the chapter “SWITCHING AUTO START STOP FUNCTION AND COASTING MODE ON AND OFF” on page 150.
The Auto Start Stop function is available with limited functionality in the following situations, e.g.:– If the air conditioning or passenger compartment heating is operated at a high setting or if the defrost function is run for long time periods.– If the battery charging condition is low.– On upward or downward slopes.– During internal vehicle test procedures, e.g. automatic engine checks.
Information
If one of these situations arises after the engine has stopped automatically, the engine can be restarted automatically.
Reaction after leaving the vehicle (selector-lever position D or N selected)
If the vehicle is left after an automatic stop when PDK selector-lever position D or N is engaged, an automatic engine start is executed to remind the driver that the Auto Start Stop function is still active.
In selector-lever position D, the electric parking brake is additionally engaged.
The brake warning light on the instrument panel and the indicator light on the switch light up.fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Reaction after leaving the vehicle (selector-lever position P selected)
If the vehicle is left after an automatic stop when PDK selector-lever position P is engaged, in order to open the garage door, for example, no automatic engine start is executed. Auto Start Stop mode is resumed if the driver closes the driver’s door and presses the brake within 30 seconds of leaving the vehicle.
If one of these requirements is not met, the engine has to be started manually. The
message “ Please start engine manually” will appear on the multi-function display in the instrument panel.fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Switching Auto Start Stop function and coasting mode on and off
Switching off
fPress button . The indicator light on the button lights up.Automatic stopping of the engine is suppressed and gliding mode is switched off.
Switching on
fPress button . The indicator light on the button goes out.The engine is automatically stopped when the vehicle stops and gliding mode is switched on.fPlease see the chapter “DRIVING IN COASTING MODE” on page 174.
14_991_Turbo_21.book Seite 150 Mittwoch, 9. April 2014 2:19 14

Driving and Driving Safety 151
Auto Start Stop function display
If the engine was stopped automatically by the Auto Start Stop function, the indicator light on the multi-function display in the instrument panel will light up green.
If the Auto Stop function is not available or if no driver is detected in the vehicle after the engine has stopped automatically (driver’s seat belt not fastened or driver’s door open), the indicator light on the multi-function display in the instrument panel will light up yellow when the vehicle is stationary.
The Auto Start Stop system has detected that: – At least one precondition for stopping the engine automatically is not met.
or – There is at least one exception for the Auto Start Stop function.fPlease see the chapter “PRECONDITIONS FOR STOPPING THE ENGINE AUTOMATICALLY” on page 149.fPlease see the chapter “EXCEPTIONS FOR THE AUTO START STOP FUNCTION” on page 150.
Information
If the indicator light in the multi-function display continuously lights up yellow when the vehicle is stopped and if the engine does not stop regularly when the vehicle is stopped despite the fact that the preconditions for stopping the engine automatically are met, have the Auto Start Stop system checked the next time you visit the workshop.
Fault reporting
If there is a fault, the warning message “ Start/ Stop operation deactivated ” will appear on the multi-function display in the instrument panel.fHave the fault corrected at an authorized Porsche dealer.
Electric Parking Brake
The electric parking brake acts on the rear wheels and serves to secure the vehicle while parked.
Applying the parking brake
fPress switch .The brake warning light on the instrument panel lights up.
For information on indicator lights and warning lights on the instrument panel: fPlease see the chapter “INSTRUMENT PANEL USA MODELS” on page 90.
Automatic engine stop and restart readiness
No engine stop or restart readiness
14_991_Turbo_21.book Seite 151 Mittwoch, 9. April 2014 2:19 14

152 Driving and Driving Safety
Releasing the parking brake
The electric parking brake can only be released when the ignition is switched on.1. Press the brake pedal. 2. Pull switch . The brake warning light on the instrument panel goes out.
Automatic electric parking brake release when driver’s intention to drive off is detected
If the engine is running, the driver’s door is closed and the driver’s safety belt is fastened, it is still possible to drive off normally even though the parking brake is on.The electric parking brake detects the driver’s intention to drive off and releases automatically.The warning light on the instrument panel goes out.
If the driver’s door is not closed or the driver’s safety belt is not fastened, the electric parking brake will not be released automatically when the driver attempts to drive off.The message “ Release parking brake” appears on the multi-function display in the instrument panel. The brake warning light on the instrument panel and the indicator light on the switch start to flash.
For information on warning messages on the multi-function display: fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Engaging the electric parking brake automatically
The electric parking brake engages if PDK selector-lever position D, R or M is selected when the vehicle is stationary and the driver’s door is opened. The brake warning light on the instrument panel and the indicator light on the switch light up. For information on warning messages on the multi-function display: fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Emergency braking function
If the vehicle cannot be stopped by conventional braking, you can decelerate sharply and stop the vehicle using the electric parking brake.fPress switch and keep it pressed.The message “ Emergency braking” appears on the multi-function display in the instrument panel. The brake warning light on the instrument panel and the indicator light on the switch start to flash.The emergency braking function is deactivated when you release the switch.
Emergency braking takes place with very high braking power. The following traffic may be endangered.fOnly use the emergency braking function in an emergency situation.fDo not use the emergency braking function to stop the vehicle when driving normally.
Brake warning light USA
Brake warning light Canada
If the electric parking brake could not be applied fully when the vehicle is stopped, the brake warning light on the instrument panel starts to flash.
For information on warning messages on the multi- function display: fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Brakes
fMake it a habit to check the operation of your brakes before driving.
Keep in mind that the braking distance increases very rapidly as the speed increases. At 60 mph (100 km/h), for example, it is not twice but four times longer than 30 mph (50 km/h). Tire traction is also less effective when the roads are wet or slippery.fTherefore, always maintain a safe distance from the car in front of you.
Severe decelerationWARNINGh
14_991_Turbo_21.book Seite 152 Mittwoch, 9. April 2014 2:19 14